Search Documents

By Peter Middendorp, David J. Tara, Gerald E. Verbeek, Jan Fischer

"For pile driving simulation the model used must be accurate for the entire process, i.e. from the start of pile driving until the pile has reached its target depth. Of the various model components (hammer, pile and soil), the soil is the most difficult to characterize accurately. This is well known, but the aspect that is not as well understood (and therefore commonly misapplied) is the fact that the soil properties and thus the soil parameters do not remain constant during the pile driving process. Furthermore, this phenomenon of soil fatigue, mainly for skin friction, as a continual change of soil resistance during pile installation, is not implemented into all commonly applied pile driving simulation software and could therefore not be taken into consideration. In this paper the effect of soil fatigue will be described by numerous research results, showing that this effect will occur regardless. Different methods to consider the change of soil resistance during pile installation will be presented, some applying soil fatigue while others merely reduce soil resistances. Using currently available wave equation software that can take soil fatigue into consideration, the importance of doing so will be shown on the basis of the back calculation of a monopile installed offshore in Germany.THEORY BEHIND SOIL FATIGUESkin friction and toe resistanceTo simulate pile installation as accurately as possible, detailed geotechnical knowledge about the mechanical behavior of the soil surrounding the pile is necessary during each step of the installation process. Therefore, to ensure ""geo-mechanical correctness"" of a pile driving simulation, the shaft friction and the toe resistance have to be recalculated at each penetration level. For the skin friction parameters this is especially important since they change significantly during pile installation because of soil fatigue. Depending on the pile and soil type, the toe resistance can experience changes as well due to soil fatigue during to pile driving. However, in this paper the toe resistance values were kept constant over the entire penetration depth.In general, the unit skin friction can be derived from measured values (CPT, qs) or calculated as a function of the horizontal effective stresses dh acting perpendicular to the pile wall of a vertically driven pile. The horizontal stresses can then be converted into the unit skin friction qs using the Mohr-Coulomb failure criterion:"

Jan 1, 2017

By K. V. Raj

"Air inversion is a meteorological phenomenon generally occurs during winter times. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for health and safety of miners. Mine operations cease if the concentration of NOx or CO exceeds the threshold limit value (TLV) of the pollutants. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Studies of the turbulence parameters suggest that effective ventilation of the pit and removal of pollutants can be accomplished if a large enough mixing length in the open pit can be created. Turbulent mixing by eddies of different length scales under an inversion layer is product of wind shear, thermal gradient and buoyancy. The main result of turbulence is mixing of the atmospheric profile and transport of momentum. Computational fluid dynamics (CFD) Simulation results of a novel mitigation approach using cloud cover will be presented in this paper. INTRODUCTION In extreme climatic conditions, deep open-pit mines tend to trap pollutants at the pit bottom due to air inversions. Keeping open pits adequately ventilated is a considerable challenge for the mining community. Mine operators in cold regions are very familiar with this problem, the severity of which can be judged from Figures 1 and 2. The top portion of the figures show clear sky and snow covered benches. The brown haze, containing various contaminants accumulated over time in the pit under the air inversion, can be seen in the bottom portion of the figures. Several Arctic or subarctic mines have reported air inversions. Even Rio Tinto’s Bingham Canyon pit in Utah has reported local air inversions from time to time [1].Mitigation of pollutants in deep open-pit mines in the Arctic is a challenging task. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for human health. Mine operations cease if the concentration of any one of the pollutants (NOx or CO) exceeds the TLV. Sustained cessation of a mine operation has serious economic consequences. For continued mining operation, the levels of pollutants must be below the TLVs. If no significant synoptic meteorological situation changes during an inversion, a warm air mass sits over the cold air mass within the open pit. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Some of the early approaches in artificially ventilating open pits were attempted in the USSR. Most of the studies by Soviet researchers suggested the use of turbojets and turbo-propeller engines, airscrews, axial pit fans, and meteotrons [2, 3]. However, the majority of these studies were only theoretical in nature, with no evidence of an approach that really worked in practice."

Jan 1, 2017

By Davood Moradkhani, Maryam Rasouli

"The present study reports solvent extraction and separation of zinc from concentrated nickel sulfate solution. In our previous study, Zn and Cd in cold filter cake (CFC, 45-55% Zn, 11-16% Cd, and 2.5-4% Ni) were extracted by alkaline leaching followed by electrowinning processes respectively. The strip solution from electrowinning process, was a pregnant liquor solution (PLS) containing 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process for separation of traces of Zn from high grade nickel. The zinc free raffinate containing 16.6 g/l Ni sulfate solution will flow to nickel electrowinning plant for cathode production. Di-(2-ethylhexyl) phosphoric acid (D2EHPA) is the organic phase used in this study. The effects of various parameters such as organic phase concentration (10- 40 % v/v), pH (1.5-3), and temperature (25 and 45°) are investigated. Zinc over nickel separation factor increases by increasing pH from1.5 to 3. The results show that 98.7% of Zn was loaded at25°C O/A ratio of 1, pH 3, and 10% vol. D2EHPA. A 10 M NaOH is used for pH control. However, replacement of pH controlling agent with ammonia solution (25%. v/v) results in interesting observations. Ammonia addition, reduces the solubility of Ni2+ cations in solution. Nickel starts to precipitate from raffinate in a crystalline bluish-green form. The obtained crystals are characterized by XRF and identified to be nickel-bearing analog of boussingaultite, a rare sulfate mineral of nickel with chemical formula of Ni (NH4)2(SO4)2.6H2O. The crystallization rate of crystals is studied. It is a slow precipitation process with 75% in 4 days.INTRODUCTION Annually, many hydrometallurgical processes such as electrowinning, solvent extraction and leaching are applied to waste filter cakes in Zanjan, Iran. These additional processes on filter cakes are critical from both environmental and economic points of view. CFC (cold filter cake) is a toxic but valuable filter cake (45-55% Zn, 11-16% Cd, 2.5-4% Ni, and 0.2-1.5% Cu) produced in many zinc production plants. Our research group at Research and Engineering Company for Non-ferrous Metals (ReCo.), developed a series of hydrometallurgical methods for extraction of zinc, cadmium and nickel from CFC (Moradkhani, & Rasouli 2012). The recovery of zinc and cadmium with alkaline leaching and electrowinning was successfully studied. The strip sulfate solution from cadmium electrowinning unit, contains high concentration of nickel with some traces of zinc impurity. This pregnant liquor solution (PLS) was analyzed and reported to contain 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process to separate Zn from nickel (Fig. 1). The organic phase stripping solution containing 4.2 g/l zinc and 200 ppm nickel can be circulated and used in the acidic leaching step. This generates nickel solution with high purity suitable for nickel cathode production."

Jan 1, 2017

By Nathaniel Schaefer, Christopher Newman, Zach Agioutantis

"As mining reserves continue to be developed in deeper and more complex geological and geometric conditions, there has been an increased demand for underground mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. Current ground control design software are limited to a given device and data files generated can only contain a single design. However, with the growth of cloud computing and increases in internet access, even underground where permissible, web-based software applications allow for in-the-field calculations, as well as collaborations, from multiple users. webGroundControl (webGC) utilizes a multiple-tier architecture, building upon existing NIOSH ground control design software, more specifically ARBS, ALPS, and ARMPS. By providing operators the ability to access ground control design programs from any device, given an internet connection, webGC allows for on demand calculations to ensure underground pillar and roof stabilities with respect to current site-specific parameters, geometries, and geology. Through the development of new features, which aid in design analyses, as well as project collaborations, webGC provides the modern engineer with a more versatile ground control design tool for the improvement of underground health and safety. With the completion of the ARBS, ALPS, and ARMPS modules, this paper introduces potential users within the mining industry to the navigation and operation of the webGC application, as well as its ability to facilitate collaborations between operational personnel and planning engineers. The purpose of this paper is to raise interest in the web-based application before its official launch in Summer 2018."

Jan 1, 2017

By S. Kelebek

Efficient separation of minerals is the essence of mineral processing. Separation of hexagonal pyrrhotite in processing of Ni-Cu sulphide ores was investigated together with particle size effects with respect to selective flotation recovery of pentlandite and nickel. The recovery by size response was compared for sodium metabisulphite (SMBS), triethylenetetramine (TETA) and their combinations with amyl xanthate as a collector. The pyrrhotite recovery for all sizes was lower than that of pentlandite for the blank case as well as individual cases with SMBS and TETA. For pyrrhotite, the recovery by size relations in the case of individual uses of reagents were mainly determined by recovery losses at coarser size range (>74 um), which occurs at a coarser size for pentlandite (>212 um). The combined use of SMBS and TETA, and the associated synergistic effect very significantly knocked down the pyrrhotite recovery to less than 7% that was a maximum for the –10 um (attributable to hydraulic entrainment). High recovery of pentlandite in a wide range of intermediate sizes and drastically low recovery of pyrrhotite resulted in a very efficient separation of pentlandite from pyrrhotite in all sizes. Separation of this mineral is discussed in relation to fundamental functionality of the reagents used.

Jan 1, 2017

By J. Erik Loehr, Minh Uong, Andrew Z. Boeckmann, Sarah G. Myers

"The University of Missouri performed a lateral load test program involving 32 drilled shaft load tests for the Missouri Department of Transportation (MoDOT). Tests were performed at two MoDOT geotechnical research sites, and all shafts were founded in shale. Shafts were instrumented to measure the displacement of the shaft head, and the structural response of each shaft was interpreted from strain gage data and from ShapeAccelArray (SAA) data. The SAA is a chain of rigid segments with sensors that use MEMS (microelectromechanical systems) technology to measure the tilt of each segment/joint. The measuring principle of the SAA is therefore similar to that of an inclinometer. The SAA device was placed in a casing installed in the center of each test shaft to provide a continuous record of deflection along the length of the shaft throughout each test.Bending moment profiles were calculated from strain gage data and from SAA data. Interpretation of bending moments from measurements of strain (via strain gages) and displacement (via SAA) is a nontrivial exercise, primarily because the bending stiffness, EI, is nonlinear and greatly influenced by concrete cracking, which is difficult to predict. The procedure used for this work predicted values of bending stiffness along the length of the shaft as a function of the bending curvature, which was interpreted from the SAA data. Values for bending stiffness as a function of curvature were computed using Ensoft LPile v2012. Bending moment profiles from SAA data were typically similar to those from strain gage data. The SAA bending moment profiles were often “noisier” than the strain gage bending moment profiles, but the SAA bending moment profiles had more data points since the SAA chain was continuous from the top to the bottom of each shaft."

Jan 1, 2017

By A. Drouin, D. Lemieux, C. Chouinard

"A gold bearing pyrite concentrate was treated at the demonstration scale (15 t/d) for the extraction of gold using a cyanide-free process. The pyrite was depressed in the flotation circuit in order to promote the flotation of copper and to achieve a sufficient copper grade to meet the copper smelter criteria. However, the recoveries of copper were 80% and only about 50% for the gold was found in the copper concentrate. The balance of the gold (50%) and copper (20%) contained in the pyrite concentrate as a reject from an overall flotation circuit. The gold grade in the pyrite concentrate is 5.40 g Au/t and copper about 0.77%. About 170 tons of pyrite concentrate were processed in the DST demonstration plant. The concentrate was first oxidized using a fluid bed to produce a calcine. Copper was then extracted as copper sulphate using diluted sulphuric acid. The residual solid was submitted to the DST chlorination process for gold extraction. Thereafter, the gold was recovered from the pregnant brine by precipitation over silica using DST proprietary process. The maximum gold recovery by chlorination was 90%. The average gold recovery by cyanidation of these calcines was 71%.IntroductionDundee Sustainable Technologies (“DST”) has developed a chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from ores or concentrates. The technology offers viable and efficient gold recoveries and the ability to handle refractory ores and contaminated material (As, Hg, etc..). The process was successfully demonstrated on hundreds of samples provided by various mines, exploration and development projects and has evolved from laboratory experiment to demonstration at an industrial scale.DST’s chlorination process operates in a closed loop circuit, which implies that no liquid effluents are generated. The chemistry and process design allows precious metal deposits containing base metals to be treated viably. The tailings from the process are inert and non-toxic, sulphide depleted and thus non-acid generating. The efficiency of the process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. The company completed in 2015 the construction of the first industrial demonstration plant operating with the DST technology. The plant has a capacity of 15 tons per day of mineral concentrate, and the ability to extract gold and silver utilizing DST chlorination technology.DST has tested its chlorination technology at demonstration scale on the refractory pyrite concentrate containing 5.40 g Au/t and 0.8 %copper. This auriferous pyrite concentrate, was by-product of copper concentrate respecting the copper smelter norms, is produced in a country where cyanide is prohibited and refractory to cyanidation. The pyrite concentrate was initially processed successfully (gold recoveries: > 90%) by the DST technology at laboratory (2011: 20 kg) and pilot (2014: 5 tons) scales to extract gold. About 170 tons of this pyrite concentrate were processed in the DST demonstration plant located in Thetford Mines."

Jan 1, 2017

By S. D. Graham

"The extractive metallurgy of gold is largely controlled by mineralogical factors such as the presence of refractory gold, particle size, gangue mineral associations, presence of preg-robbers, oxygen and cyanide consumers, and locking characteristics in base metal sulphides. Light microscopy and automated mineralogy techniques are regularly used to characterise the effect of these variables on gold recovery. However, despite their widespread application there are a range of limitations when grades are low. Typically, the analysis of low-grade samples requires the preparation and analysis of numerous polished blocks. This is often costly and time consuming, with complexities regarding analysing statistically representative particle quantities and problems overcoming stereological bias. This is compounded by the “nugget” effect and high tenor nature of gold mineralisation. X-ray Microscopy techniques have the potential to overcome many of these problems, in particular the statistical representivity of analysis, removing stereological bias and effectively locating phases that are present in ultra-trace proportions. In this paper we outline the potential benefits of employing X-ray Microscopy (XRM) in characterising gold losses from a typical Cu-Au porphyry project, which were illusive in 2D based analysis. The talk will also outline additional application areas of XRM within the extractive value chain."

Jan 1, 2017

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By Vighnesh Chandurkar, Peter Moser, Michael Hitch, Michael Tost, Susanne Feiel

"From 1998-2002 the world's leading mining and metals companies developed the Global Mining Initiative (GMI) to understand their industry's role in the transition to sustainable development and to ensure its long-term contribution to sustainable development (SD). Since then, the industry has come a long way: For example, operational safety and health have improved significantly, environmental management systems and impact assessments have become the norm, community relations have been established, many mining companies report annually on their contributions to SD and the International Council on Mining and Metals (ICMM) has taken on the recommendations of the GMI as an industry association. However, since the GMI the concept of sustainable development has been evolving from a rather generic and loose definition (“weak sustainability”), to an absolute and strict definition of sustainability, based on the boundaries of our planet (“strong sustainability”). Similarly, other concepts such as corporate social responsibility (CSR) have evolved and even deviated from their initial intentions. This paper presents results from a literature review looking at how far this transition has moved from a scientific debate towards becoming mainstream. Furthermore, it explores, by using qualitative comparison analysis, if the current efforts of the large mining companies are still sufficient or if the industry is again at risk of falling behind societal expectations and hence should once again come together - for a GMI 2.0 - in order to update its approach. We conclude that the mining industry, whilst in a “weak sustainability” position and behind the peer group on climate change and natural capital considerations, is aligned with current societal expectations, expressed through the Sustainable Development Goals, and therefore there is no need for a GMI 2.0 at present."

Jan 1, 2017

By Qi Wang, Zengzhu Kang, Jianguo Liu, Guanglei Liu

"Due to the increase of automotive vehicles, available parking spaces become a new type of limited resource in central cities of China, especially in those old districts without visionary urban planning. Additional mechanical parking in underground space is an efficient solution to provide parking spaces under the situation where the urban space is constrained. Shichahai district is an old protected zone in Beijing which is close to the Forbidden City and there are many Hutong (alleyway) and Quadrangles (courtyard house). No spaces are available for car parking on the ground and all vehicles are parking in Hutong without order currently. The local government plan to do renovation work for this district and improve the residential environment. Several innovative solutions are studied including parking in deep shafts, parking under existing buildings by under-pinned method, parking under buildings by covered excavation method, parking under roads built together with utility tunnel etc. 5000 difference types underground parking spaces are planned to be constructed in the following three years. Project examples are also introduced in this paper. INTRODUCTIONCar parking resources are very limited in central cities, especially in old districts without planning for increasing automotive vehicle volume. Traffic get worse when cars park on the side of the roads or move slowly to find parking spaces. Investigation shows the normal (parking space/ automotive vehicle volume) ratio is about 1.2 in most big cities such as New York, Tokyo and Hong Kong, while this ratio is only 0.5 in Beijing. One solution is to move cars out of central cities. But there are still huge parking requirements for the citizens living in central cities. Shichahai district is an historic protected zone in Beijing which is close to the Forbidden City and there are many Hutong and Quadrangles (refer to Figure 1 for project location). No spaces are available for car parking on ground and all vehicles are parked in Hutong without order currently. The local government had a plan to do renovation work of this district and improve the residence environment. 5000 different types of underground parking spaces are planned to be constructed in the following three years. One project designed and to be constructed by Zhongyan Technology will be introduced in this paper. Other innovative solutions will be introduced briefly as well."

Jan 1, 2017

By Tracy Brettmann, Melis Sutman, C. Guney Olgen

"The use of energy piles for geothermal heat exchange has been steadily increasing during the last decade, yet there are still pending questions on their behavior during temperature changes. This paper focuses on the thermo-mechanical response of three full-scale energy piles installed in Richmond, TX. The behavior of test piles subjected to thermo-mechanical loadings was studied in situ with the aim of quantifying the thermal influence on the performance and capacity of energy piles. An extensive field test program, including conventional pile loading tests and application of heating-cooling cycles was conducted on the test piles during a period of six weeks. For thermal load applications, the heat exchanger fluid with maximum temperature of 113°F (45°C) and minimum of 47°F (8°C) was circulated in the geothermal loops placed at the center of the test piles. Optical fiber sensors, vibrating wire strain gages, thermistors and thermal integrity profile wires were installed to monitor the strain and temperature variations along the energy piles throughout the field tests. The strain and temperature profiles during heating-cooling cycles on the test piles under static loads and without a maintained load were monitored to investigate the effect of thermo-mechanical and pure thermal loads on the energy piles, respectively. Conventional pile load tests were applied before and after the application of thermal cycles. The results of the pile load tests are compared to evaluate the effect of temperature cycles on pile capacity.IntroductionEnergy piles are deep foundation elements designed to access and exploit the relatively constant temperature of the ground and its heat storage capacity for efficient heating and cooling of buildings. The deep foundation elements that are already in place for structural support are integrated with adsorber pipes to perform as heat exchangers connected to ground source heat pump (GSHP) systems. With the use of energy piles, the heat energy is fed into and withdrawn from the ground for cooling in the summer and heating in the winter, respectively.Energy piles present an innovative way to harvest near-surface geothermal energy and to provide lower carbon emissions, however, there are still pending question on their performance. During heating-cooling cycles, energy piles experience temperature changes, which result in expansion or contraction of the piles."

Jan 1, 2017

By M. B. Kime, E. K. Kanowa

"Heap leaching of low-grade copper-cobalt oxidized ore and solvent extraction of copper, cobalt, manganese, and zinc were investigated. Heap-leaching parameters were optimized using agitated and tray batch leaching tests, capped by tests on a pilot semicontinuous heap-leach plant. The optimum pregnant leach solution yielded 2,350 mg/L Cu, 3,800 mg/L Co, 3,600 mg/L Fe, 130 mg/L Mn, 25 mg/L Zn, and 0.58 g/L solids in suspension, with pH and acidity of 1.27 and 3.66 g/L, respectively. Copper, cobalt, and impurities (Mn and Zn) were extracted using (v/v) 30% CP-150, 20% IONQUEST® 290, and 20% D2EHPA, respectively; overall recoveries of copper, cobalt, and impurities were 98, 99, and 70%, respectively.RÉSUMÉ La lixiviation en tas des minerais oxydés de cuivre et de cobalt et l’extraction par solvant du cuivre, du cobalt, du manganèse et du zinc ont été étudiés. Les paramètres de lixiviation en tas ont été optimisés à l’aide d’essais de lixiviation en discontinu sur un plateau, complétés par des essais relatifs à une usine pilote de lixiviation en tas en semi-continu. La liqueur-mère optimale a produit 2 350 mg/L de Cu, 3 800 mg/L de Co, 3 600 mg/L de Fe, 130 mg/L de Mn, 25 mg/L de Zn et 0,58 g/L de solides en suspension, avec un pH et une acidité respectifs de 1,27 et 3,66 g/L. Le cuivre, le cobalt et les impuretés (Mn et Zn) ont été extraits avec un pourcentage volumique (v/v) de 30 % de CP-150, de 20 % d’IONQUEST ® 290 et de 20 % de D2EHPA, respectivement. Les récupérations totales de cuivre, de cobalt et d’impuretés étaient de 98 %, 99 % et 70 % respectivement.INTRODUCTIONBoss Mining S.P.R.L. is a privately owned hydrometallurgical plant located in southeastern Democratic Republic of Congo. It treats oxidized ores of copper and cobalt that are recovered by sulphuric acid heap leaching (Trujillo, Cisternas, Gálvez, & Mellado, 2014; Kime, Kanowa, Mulaba- Bafubiandi, & Diyambi, 2016) and solvent extraction processes (Crane, Urbani, Dudley, Horner, & Virnig, 2009; Fisher, 2011; Kime et al., 2016). The ore to the plant is primarily sourced from the Luita and Mukondo mines. Geological prospecting work by Gecamines and Boss Mining showed that the Mukondo mine contains a very large cobalt reserve not yet exploited, but with grades as low as 0.2%.Currently, Boss Mining is focusing on the production of copper, but is investigating methods to efficiently produce both copper and cobalt. A challenge in the production of cobalt from this ore is its presence in the third oxidation state. This requires the addition of reducing agents, which increases the overall operating cost (Kime & Makgoale, 2016). Cobalt solvent extraction is also very sensitive to impurities such as nickel, zinc, manganese, and aluminum, which are often co-extracted (Swartz, Donegan, & Amos, 2009). This sensitivity to impurities requires the optimization of operational parameters to lower impurity levels as much as possible in the electrolyte."

Jan 1, 2017

By William (Bill) H. Walton

"I arrived in Chicago in 1993 with Dr. Ralph Peck’s University of Illinois bulletin titled Engineering Properties of Chicago Subsoils (Bulletin 429), which he published in 1954 with William Reed. Being an outsider, I wanted to learn from Chicago geotechnical practice leaders that included Clyde Baker, Jr., John Gnaedinger, Charles Pfingsten, Dr. Safdar Gill, Robert Lukas and Dr. Jorj Osterberg, who have influenced foundation designs for the structures that make up the contemporary Chicago skyline. One of my immediate goals was to get the Illinois Structural Engineering license to be on par with the likes of Eli Cohen, Mike Tylk, Stan Korista, Bob Halverson, Joe Burns, Ron Johnson, Bill Baker, Bob Sinn, Chuck Anderson and Dave Eckmann, who have led their structural firms in the design of the skeletal core and frames of many of Chicago’s iconic buildings (and for many other buildings around the world). From my time with GEI Consultants (GEI), then on with STS Consultants (STS, and now AECOM), and now back with GEI, I have had the opportunity to analyze and design foundations and, with the help of many skilled foundations and building constructors, to verify that predicted foundation performance matches actual movement data. The theme of Chicago’s foundation design practice is to assume and verify. In 1948, Peck published the History of Building Foundations in Chicago (Bulletin 373) that was updated in 1998 by Baker, Pfingsten and Gnaedinger, who meticulously documented hundreds of Chicago’s foundations, and have shown the value of advanced analyses and testing to advance the deep foundation design practice that includes a variety of high-capacity driven and drilled deep foundations. Mehmet Uyanik, Peck and Baker have made Chicago’s subsurface into a full-scale foundation test laboratory. They confirmed soil mechanics principles like Terzaghi’s 1-D consolidation theory when early foundations bearing on sand-clay crust over soft to medium silty clays (e.g., Auditorium, Masonic Temple, Monadnock Block and Old Board of Trade buildings) took 40 to 60 years to consolidate clay 1 to 2 ft (0.3 to 0.6 m). They also confirmed proven increases in bearing pressures based on measured performance of deep foundations bearing on the glacially derived hardpan clay till and in solid dolomite that underlies Chicago."

Jan 1, 2017

By Ilhan Chang, Ernest Nsabimana, Kiseok Kwak, Juhyung Lee, Young-Hoon Jung

"Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.IntroductionWith the development of offshore technology, applications and real site installations of suction piles are increasing significantly nowadays. They are generally used as mooring anchors in various floating structures, marine platforms, and offshore wind turbines. According to its convenience in installation and removal, suction type foundations are becoming good alternatives for deep ocean support systems. The bearing capacity is similar to the bearing behavior of ordinary offshore structures (piles or drilled shafts). The most common use of suction caissons is anchors for catenary mooring lines, where the chain angle at the mudline is close to zero (Randolph, 2002; Sharma, 2004).Recently, it is reported that a huge isolated single suction pile can be replaced by a group of moderatesized suction piles (Randolph et al. 2004). A single monopile is easy to be produced and installed in site. It is expected that monopile foundation is not applicable for deep depths because it has a limitation on penetration according to its huge side skin area (i.e. friction). Moreover, stiffness requirements sometimes render thicker pile wall conditions which are impractical to be produced."

Jan 1, 2017

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

By Morgan M. Sears, Mark Van Dyke, Gamal Rashed, John Rusnak, Khaled Mohamed

"In 2016, room-and-pillar mining provided nearly 40% of underground coal production in the United States. Over the past decade, rib falls have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Nine of these 12 fatalities (75%) have occurred in room-and-pillar mines. The objective of this research is to study the geomechanics of bench room-and-pillar mining and the associated response of high pillar ribs at overburden depths greater than 1,000 ft. This paper provides a definition of the bench technique, the pillar response due to loading, observational data for a case history, a calibrated numerical model of the observed rib response, and application of this calibrated model to a second site. INTRODUCTION Bench mining is a an underground mining technique typically applied to room-and-pillar mines where full seam extraction on development presents an unacceptably high risk of injury from high pillar ribs or where the mining equipment is not designed to extract the full seam thickness. To mitigate the increased risk associated with high ribs and slender pillars, a more modest thickness is extracted from the top of the seam on development. This is followed by grading the floor and recovering the bottom of the seam with or without extraction of the pillars during retreat mining. A mine located in Eastern Kentucky extracts two seams at depths ranging from outcrop to 2,000 ft. In some areas of the mine, Seam A and Seam B are close enough together to be mined simultaneously. Seam A (top) is mined on development 7 to 9 ft. high for the entire length of the panel. On retreat, as each pillar is extracted, the continuous miner is ramped down into the floor (Seam B), two pairs of Mobile Roof Support (MRS) units are set, and the pillars are extracted at the full mining height of 14+ ft. During the pillar recovery process, the floor is extracted in each entry, from a ramp initiated outby the retreat line, sequentially just prior to extracting the lifts from the pillars (see Figure 1)."

Jan 1, 2017

The Curtin University Gold Technology Group has been involved in surveying, modelling and optimisation of batch centrifugal concentrator type gravity circuits and CIP/CIL circuits for nearly two decades. The most commonly asked question regarding gravity recovery is, “What is the benefit of a gravity circuit”, which can be hard, if not impossible, to quantify. With the help of the AMIRA P420 Project’s Integrated Liberation Leach Model (ILLM) it is now possible to evaluate the effect of gravity recovery on total gold recovery when changes are made to the grind size, gravity and/or leach/adsorption circuits. This paper demonstrates how the ILLM can be used to determine the net benefit of introducing or modifying a gravity circuit and assess the effect of operating conditions (grind size, coarse gold size distribution, leach residence time, carbon activity, etc.) on plant performance.

Jan 1, 2017

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017