Search Documents

By Lana Alagha, Ashraf Alsafasfeh, Amal Al‑Hanaktah

As freshwater resources are becoming scarce, the use of seawater as replacement of fresh water is appealing in order to make mineral processing operations more sustainable. Since froth stability plays a critical role in determining the performance of flotation operations, there is an urgent need to study the effect of frother dosage and seawater on froth stability. In this study, flotation tests in seawater were conducted to examine the effect of frother’s dosage (MIBC) on the froth stability and flotation performance of low-grade phosphate ore. The stability of the froth layer was assessed by measuring the froth growth velocity and the froth maximum height at equilibrium. Results indicated that the best flotation performance was obtained at 75 g/ton of MIBC where ~ 90% of phosphate minerals were recovered. At this recovery value, the concentrate grade was determined to be ~ 70%. Results from froth stability experiments showed that the stability of the froth layer increased by increasing MIBC dosage. At MIBC dosage of 75g/ton, the calculated values of dynamic froth stability and the froth height were ~ 0.4 cm/sec and 16 cm, respectively.

Jan 17, 2024

By Han Zhao, FENGLIANG WU, Tong Wang

Calibrating an entire mine ventilation network model from survey data has long been considered a challenging and sometimes impractical task. This paper proposes a solution to this issue with the development of a quadratic programming optimization model. The optimization model takes the minimum modification of input resistances as the objective function, uses the mesh pressure equations as equality constraints, and incorporates the lower limits of airway resistances as inequality constraints. A two-step method is developed to solve the model, which includes finding an initial feasible solution and iteratively solving the final solution using the active set method. A computer program has been developed to implement the optimization model. To demonstrate its practicality, a study case using a 35-branch ventilation network is presented, which indicates that the solution process converges after only 57 iterations, a significant improvement over the times of trial and error, which could reach 3.4 × 1010 for the worst-case scenario. Additionally, it is shown that considering only the equality constraints results in negative resistances, while incorporating the lower limits of resistance ensures that the corrected resistances are within a reasonable range. Using the resistance corrected by the optimal model to simulate the ventilation system via traditional methods generates quantities and fan pressures that perfectly match the measured values, eliminating the tedious process of manually adjusting airway resistances repeatedly.

Jan 13, 2024

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicated the potential for scrap formation, validated through lab experiments with varying coke rate, basicity, and holding time. The investigation discovered that smelting this combination could yield a metal product comprising 59% Fe, 24.93% Cr, 7.56% Mn, 0.62% Ni, and 0.93% Si. The optimum basicity was found to be 0.6 with 80% recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall CO2 emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of USD 330 per ton.

Jan 10, 2024

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

This study presents the results of the mineralogical characterization of Ti-Zr ore from the Jiboia deposit, located in the municipality of Brejo Grande, Sergipe State, Brazil. The goal is to identify the main Ti, Zr, and REE carrier phases in the different particle size fractions in order to subsidize the development of a cost-effective processing route for the production of heavy minerals concentrate. The mineral resources are estimated at 31.5Mt @ 3.5% of total heavy minerals (THM) for the Jiboia Ti-Zr deposit, of which 5 Mt @ 3.39% THM were classified as measured and indicated. The mineralogy of the heavy mineral concentrate recalculated to 100% is represented by 22% pseudorutile, 20% ilmenite, 15% zircon, 5% rutile, 2% monazite, and 36% gangue. The ore minerals are preferably concentrated in the 150 × 53-μm granulometric fractions, which represents 80% of the THM and only 27% of the ROM (Run-of-Mine) ore. Therefore, by cutting the ore to 150 μm, it is possible to discard 73% of the ROM mass and recover 80% of the THM, including 100% of the zircon and monazite which are the most valuable minerals present in the heavy mineral concentrate. The global recovery of THM starts to decline rapidly in the fractions finer than 106 μm and the mass disposal (tailing) does not follow in the same proportion. Higher zircon contents in the concentrates of the fractions finer than 150 μm imply a significantly lower recovery of heavy minerals like ilmenite, pseudorutile, and rutile that make the fractions coarser than 150 μm.

Jan 9, 2024

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

Among underground coal miners, roof bolter operators are generally considered to have some of the highest risks for hazardous respirable dust exposure. This is because bolting requires drilling into roof strata that can often be a source of silica and silicate dust, which are associated with occupational lung diseases. However, little is known about the variability of dust characteristics (e.g., mineralogy constituents, particle size) in the vicinity of the bolter—or when specific dust controls are applied. As part of a prior NIOSH study, respirable dust samples were collected during several different events in standardized locations around an active roof bolter, and personal samples were also collected from the operator during the cleanout of the bolter’s dust collection system when it was equipped with a novel wet dust box versus a traditional dry box. Those samples were made available for follow-up analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDX), as well as direct-on-filter Fourier transform infrared spectroscopy (FTIR). Results showed variability in dust constituents and particle sizes at locations around the roof bolter, and indicated some event-to-event differences in dust sources. Additionally, compared to the dry dust box, the wet dust box appeared to reduce (by 41–82%) the relative silica and silicate content in the respirable dust to which the operator was exposed during cleanout. Furthermore, an inter-laboratory comparison demonstrated the reproducibility of a standardized direct-on-filter FTIR method for estimating quartz mass (i.e., the predominant form of crystalline silica) in respirable coal mine dust samples. However, for constituent analysis by SEM–EDX, differences observed between results from two independent labs indicate that standardization of the analytical protocol is necessary to enable comparability of results.

Jan 5, 2024

By Jian Zhou, Shuai Huang, Wenqin Xi, Kun Du

The deep oceans harbor a wide variety of mineral resources that are characterized by their abundance and high quality. Nations worldwide are actively pursuing the exploration and extraction of these resources. This paper provides a concise overview of the mineral resources found in the deep sea, highlighting the challenges associated with their exploitation. Furthermore, it presents a comprehensive analysis of the historical development of deep-sea mining technology and equipment, offering valuable insights into this field. By examining the current issues and obstacles faced in deep-sea mineral extraction, this study concludes that the future of deep-sea mining lies in the direction of automation, intelligence, and standardization. Additionally, it identifies the key technological advancements that need to be achieved in order to overcome the challenges associated with deep-sea mining.

Jan 5, 2024

By E. Líder, J. Pavez, J. Rivera

The application of new technologies, methodologies, and the use of new products in mining operations is a practice that is becoming more common in the industry every day, added to the new challenges and restrictions found in the operation. In the city of Tierra Amarilla, the interaction between mining operations and the community presents a constant challenge given the proximity to the community and the limitations that this presents. Explosive charge mass, in conventional blasting using traditional explosives (ANFOs, packaged explosives for example) limits the explosive charge lengths (they are reduced), impacting the explosive charge productivity. To improve the productivity of explosive charge and fragmentation, the use of low-density explosives was proposed, allowing the increase of the explosive charge length, trying to maintain the vibration levels within the established limits (2mm/s), preserving the fragmentation of the rock in the required sizes. The present study shows the results obtained from the application of low-density bulk emulsion for production blasting charges using upward and downward fan drillings. During this process, 18 blasting events were carried out, of which 8 were Up-hole loading (average density of 0.75 gr/cc) and 10 with Down-Hole loading (average density of 0.95 gr/cc). In summary, a total of 110,760 tons of ore have been broken, using low density emulsion, meeting the proposed objectives such as: 33% reduction of vibrations, 12% overbreak (within the theoretical design), P80 of 11in and 4.6% in fines.

Jan 1, 2024

By J. Sanchidrián, A. Fernández, P. Segarra

The combination of chemical analysis techniques as XRF and measurement-while-drilling (MWD) technology in underground mining is a novel approach to gather comprehensive on-line information about physical and mineralogical data. In this work their integration is investigated aiming to delineate the ore/waste boundary. The input data analyzed come from a narrow vein underground mine, where the ore correspond to fluorite, and gathered in two production levels with complex mineralogical characteristics. Two approaches are followed to build a generalizable classification methodology and a site-specific model: a k-means clustering heuristic algorithm to define rock classes based on their physicochemical features, and a machine learning (ML) ensemble model trained with drilling parameters. For an imbalance class problem, a good recognition is obtained for the ore when is related to a high content of silica and for the waste. To predict the ore with low silica content it is necessary to integrate an analysis-while-drilling method to recognize the fluorite content when this mineral is embedded in different rocks. MWD can be employing for the lithologies recognition when representing different structural and mechanical properties between them.

Jan 1, 2024

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024

By P. Lozada

The objective currently demanded from controlled blasting techniques is to minimize damage to the remaining rock mass while protecting the integrity of mine walls and ensuring the quality of the fragmented material for easier extraction. Finding this balance represents one of the three main challenges faced by large open-pit mines. They must achieve mine stability by complying with slope designs while also maintaining good results in terms of fragmentation and equipment productivity. The main constraints are related to unfavorable geological conditions, water presence, limited drilling diameters and available explosive products, as well as managing drilling times and blast scheduling, among others. For slope control, in addition to presplitting, blasting designs generally include buffered rows, drilled with smaller diameters, and loaded with fewer kilograms of explosives than production holes. The objective is to reduce the powder factor (kg/t) to minimize the energetic influence on the walls and attenuate damage. However, this often requires using very short charge lengths compared to the bench height (one-third or less) and reducing the pattern geometry, which increases the number of holes per ton and drilling costs. This traditional technique of reducing powder factor in the buffered rows has the main limitation of not being able to distribute the explosive energy throughout the entire column, leading to fragmentation issues mainly in the steaming area. Measurements conducted by Orica in their operations indicate at least a 30% increase in P80 particle size in the buffer zone associated with this condition. To improve energy distribution, techniques such as decking, or vertically decoupled charges can be employed. However, these techniques cannot be applied under wet conditions, and strict control over implementation quality is required to avoid deviations, which increases loading operational times and resource required. In this sense, the use of less energetic and lower-density explosives is a better alternative. On one hand, they allow for complete charge columns in the buffered rows, ensuring homogeneous fragmentation, and on the other hand, they reduce the energetic influence on the slopes, significantly decreasing vibration levels. With less energy per kilogram of explosive (MJ/kg) and less charge per linear meter (kg/m), it becomes possible to handle higher specific charges and longer explosive columns, providing flexibility in drilling and loading design options without compromising slope stability.

Jan 1, 2024

By C. Breeds, K. Jeremiah, E. Jennings

Washington State has a well developed set of blasting regulations which have been promulgated by the Department of Labor using extensive stakeholder input, not only from citizens but also from manufacturers and representatives of IME, blasters in charge, blasting engineers, blasting companies, local and federal law enforcement agencies, fire officials, and local and state government representatives. WAC 296-52 therefore provides a foundation or platform for developing city ordinances for Washington State cities should a City wish to do so. On the other hand, Oregon’s code is based on OSHA 1926, Subdivision U, Blasting and the Use of Explosives which provides scant direction regarding the modern use of explosives. Reference is also made to ODOT Section 00335 - Blasting Methods and Protection of Excavation Backslopes. This paper examines two separate programs that have been developed by two Cities, one in Washington State and one in Oregon to further regulate blasting inside City limits and discusses why the lack of a regulatory foundation made one approach more difficult than the other. One of the authors was retained by the City of Kennewick, WA to develop their ordinance and has more recently followed and reacted to a pending ordinance for the City of Redmond, Oregon. The paper will compare and contrast the different approaches and comment on the reaction from both Blasters and the public. We also present a case study that involved blasting in an urban area of Oregon to prepare a foundation for a water tank. Controlled Blasting was carried out within 70-ft of residencies and within a community that had expressed reservations regarding blasting even though the work would make a significant contribution to the betterment of the community. Pre-construction surveys of residencies located in a large area surrounding the site were performed and a well-planned blasting program was carried out. Residencies were subject to vibration levels that were monitored using six seismographs that surrounded the site and these units measured vibration levels that were significantly lower than allowed by statute. There were complaints triggered by individuals reactions to blast vibrations which validated commonly held models of human perception but no damage was caused by the Blasting.

Jan 1, 2024

By P. Couceiro, J. Navarro

A new methodology to perform selective blast designs by adapting the explosive energy, hole by hole (or in the hole), to the rock properties as a combination of their strength properties through the X-Rock model has been developed based on drill-monitoring data from both autonomous and manual rotary drilling modes. For that, a thorough normalization process has been developed to minimize external influences in the data induced by the different rig system and the operator interventions during manual drilling operation. Principal component analysis has been used to combine drill monitoring information. Data from 48,385 blastholes, comprised in 102 production blasts at 7 different levels in one expansion of the mine have been used for the analysis. The methodology, called X-Energy, combines the X-Rock model outputs with actual blast design parameters (drill pattern, stemming and borehole length, explosive mass/density and others) and a constant variable obtained from a machine learning algorithm, to estimate size distribution and percentage of fines and coarse material, hole by hole, by combining and recalibrating the Kuznetsov (Cunningham, 1987) based equation. From it, a new shovel-independent diggability model has been developed as combination of the P80 size, the rock properties (from the X-Rock) and a constant variable obtained from a machine learning algorithm. The X-Energy application presented in this study have been implemented in Minera Escondida Limitada (MEL), to design and operate production blasts with the goal of varying the explosive density to the rock properties to obtain a more uniform size distribution and digging rates, hole by hole, based on a target size and rate, and improving slope care, preventing active faults to fail. The methodology has been applied and validated in 17 production blast (8,277 blasthole), unlocking an average of 12.8% reduction in explosives costs (explosive consumption), by combining a pattern expansion strategy and a better distribution of the explosive density within the blast. The results demonstrate how a better distribution of the explosive energy by varying its density in the hole according to the rock and blast geometry variables can reduce powder factor (explosive consumption) while improving or maintaining blasting and digging results.

Jan 1, 2024

By M. Araos

Non-ideal explosives can be characterised by different methods like velocity of detonation measurement, double pipe tests, underwater tests, aquarium tests, etc., to name a few. Both aquarium and velocity of detonation tests were selected to characterise a non-ideal explosive that is based on hydrogen peroxide, fuel, and void sensitisation. The detonation process in an aquarium of this sensitised explosive was captured at 80,000 frames per second using a high-speed camera. The explosive product was detonated using 51mm (2inches) diameter acrylic pipe charges. The product was detonated at different densities in an aquarium (cube box containing water). An aquarium provides a homogenous confinement for the detonation of explosives and more importantly, allows observing the shock wave as it changes the refraction index of water. The analysis of the video footage allowed the calculation of the velocity of detonation, pressure, gas rate release, and how the shock wave's shape in water changes with densities. It is suggested that the calculation of the rate of gas release could be related to the bubble data obtained from underwater tests.

Jan 1, 2024

By A. Gontijo, A. Matos, P. Lincoln, L. Fonsecail

This paper investigates how to manage and model the vibrations caused by rock blasting in a Brazilian underground mine. Considering the frequent detonations and the previous lack of effective vibration control, understanding, and reducing the impact of these seismic waves is critical. We emphasize the use of the near field model technique, which considers the varied physical properties of different rocks, optimizes blasting plans, and minimizes damage to the rock mass. We detail a case study that demonstrates a comprehensive approach to vibration control. The discussion includes the creation of a monitoring plan, the methodology used, results and the specific challenges and solutions found during the blasting process. This study provides a practical guide for similar future projects. Finally, we present a predictive model based on the collected data, offering insights into the vibrations caused by blasting. This model helps decision-makers minimize the risk of displacing rock blocks in the blasting area, improving safety and operational efficiency

Jan 1, 2024

By J. A. Sanchidrián, P. Segarra, S. Gómez

Blasting is a common activity in mining that can cause significant damage in the remaining rock mass. The most commonly used method for predicting vibrations is the Swedish or Holmberg-Persson approach. It is a simple and fast method that uses empirical formulation to estimate the vibration levels based on the explosive charge weight, distance to the source, and other parameters. However, it has limited accuracy and does not consider the effect of free surfaces or other boundary conditions. On the other hand, recently developed methods as the full-field solution (FFS) can provide more accurate predictions of vibrations due to excitations provoked by cylindrical columns of explosive, but the inclusion of free surfaces in analytical methods is a challenging problem. This paper presents a new approach that includes free surfaces in the FFS to predict vibrations analytically in the near-field. The main obstacle to including free surfaces in the FFS was the belief that the solution was non-decoupleable in P- and SV-waves separately. The Heelan's approach was previously used to decouple them, but it only provides valid radiation patterns in the far-field and does not account for intrinsic attenuation. In this paper, we address this problem successfully, allowing for the inclusion of free surfaces in the FFS.

Jan 1, 2024

By A. Ribeiro

The effective utilization of resources and process optimization play a crucial role in the sustaining and growth of overall businesses. This principle holds true in the mining sector, where particular attention is required during the comminution steps. This necessity arises from the fact that mining operations often consume substantial amounts of energy in mineral processing. Therefore, it becomes imperative to thoroughly study the integration of comminution steps. In many instances, an approach to be studied is the operation commencing with the drill and blast phase and culminating in the grinding product process. Nevertheless, establishing an optimal integration between drill and blast operations and the grinding phase is a complex undertaking due to the direct influence of rock characteristics on this process. And in many cases, the complexity and variability of such physical characteristics makes mining operations to ignore such influence. Consequently, Enaex Mining Technical Solutions (EMTS), in collaboration with Lundin Mining's Chapada Mine engineering team, and with the assistance of Hatch Consulting and Technology, has undertaken a comprehensive study aimed at enhancing mill throughput at the Chapada operation. The basis of this study lies in characterizing the rock masses present in the Chapada Mine to gain a deep understanding of the material that needs to be comminuted. Subsequently, the mineral processing team determined the most suitable size distribution for the Run-of-Mine (ROM) material. With this information, the drilling and blasting team built a site-specific blast fragmentation model, able to simulate various blast design scenarios. This approach enabled to optimize the utilization of available drilling and blasting resources while striving to achieve the optimum ROM characteristics. Since 2021, the Mine to Mill methodology has been progressively implemented at the Chapada Mine. As a result, the blasting engineering team now utilizes the blast plans generated by the fragmentation model simulations as a foundation for designing blast plans that align with the operational and financial capacities of the mine. Overall, it was predicted that this implementation could lead to an average increase in mill throughput of 13-22 % depending on blend feed, once all recommendations are implemented. Even with partial implementation, plant results demonstrate a 5 % increase compared to the period before the Mineto-Mill project, without any coarsening of the associated grinding product size.

Jan 1, 2024

By R. Hazael, R. Alford, R. Critchley

The ability to compare explosives is fundamental. Numerous methods are used and while simple conversion factors are often used, the use of TNT Equivalency (TNTe) is not a simple subject as explosives exhibit very different equivalencies depending on whether the pressure or impulse are being considered as well as other conditions. The scaled distance has been found to have a significant effect on the TNTe but due to the difficulty of taking measurements at very close ranges, no TNTe have been quoted for charges in direct contact (Z=0). This paper describes the use of a ballistic pendulum to measure the impulse from contact charges and presents some surprising results that require a two-stage propulsion, as originally described by Backofen, to be explained.

Jan 1, 2024

By C. Aimone-Martin, C. Dowding, M. Jern, J. Gjødvad

This article compares percentages of compliance for six national standards to demonstrate how these standards vary on-site in a real project. This, to the best of the authors' knowledge, has not been accomplished before. Different standards not only vary in allowable amplitudes of induced vibrations but also in how they are measured (transducer location, transducer orientation, frequency content of vibration, etc.). Thus it is not straightforward to compare the permissible values of induced vibrations with each other. This challenge of comparison is overcome in this project by instrumenting a structure with multiple transducers according to different national standards and comparing the degrees of compliance. Compared herein are compliance with standards used in United States of America, Germany, Great Britain, France, Austria, and Sweden. Averages of the percentage of compliance and ratios of measured vibration amplitudes for all six national standards are compared both in tabular and graphical form for 20 blasts at the Aitik mine northern Sweden. It is the largest open pit mine in Europe and blasts are atypically large with more than 1000 kg charge per hole and several hundred holes per blast, lasting 3-5 seconds. Results show that percentages of compliance can vary by as much as 2 to 75 % for these blasts at this structure. The overall project is a cooperative effort between EFEE (European Federation of Explosives Engineers) and ISEE (International Society of Explosives Engineers), supported by more than 17 persons from 8 different countries. At the present the experts are the four authors of the present paper and Dr. Robert Farenfield, Dr. Nathan Rouse, Douglas Rudenko, Brent Meins, Kenneth K. Eltschlager, Karin NorénCosgriff, Travis A. Davidsavor, Vitor Luconi Rosenhaim, Johannes Kutschera, Bernard Thierry, Thomas Moser, Cory Loukedis, and Keith Best. The project began with a literature study and a survey including an evaluation of the answers provided by members of EFEE. Results were presented at the ISEE conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019 (Gjødvad & Jern, 2019; 2020). The second part of the project was initiated in May 2021 with installation of 7 seismographs from two different manufactures, 3 cracs gauges and 2 microphones on a building at the Aitik mine in northern Sweden. The third part of the project has moved to the United States. Two residential structures adjacent to quarries are being monitored in Michigan and Ohio. Installation and monitoring began in March 2023 and are expected to continue for 6 to 12 months. In addition to the objectives of phase two the 2023 study includes calculations of global wall strains from measured velocity time histories and measurement of response of existing cracks to vibratory and climatological effects

Jan 1, 2024

By C. Morel, P. Fredes, L. Rojas

This article presents a comprehensive study on the development and application of the specific module called "Exclusion Zone" created by Orica to determine blast evacuation exclusion zones. This module, integrated into the "SHOTPlus™ (blast design software)" software, has been used in the context of optimizing equipment evacuation exclusion zones in a northern Chile mine. The main objective has been to reduce the travel times of extraction equipment without compromising the safety of individuals. The module considers various factors such as the explosive charges used, stemming, sector topography, and detonation sequence to determine the rock projection generated by the blast. Furthermore, it utilizes information collected by drones and support tools such as Groundprobe and BlastVision™. The results obtained demonstrate that the use of this technology has allowed the optimization of blast evacuation distances in the northern Chile mine, generating significant economic benefits for the client.

Jan 1, 2024

By N. Skopak, W. Birch, A. Douglas, C. Johnson

Determining the origins of air overpressure has been a long-debated topic within the explosives engineering community. Historically, it has been accepted that the initial face movement gave rise to air displacement, resulting in an air overpressure pulse. Later research proposed that the air overpressure pulse resulted from the shockwave rapidly propagating through and impacting the quarry face. Most recently, researchers have derived that air overpressure is associated with the gas phase from which a gaseous product from explosives rapidly pours out the quarry face under high pressure. Significant research has strongly indicated that the time at which the air overpressure pulse exits the face fails to coincide with either the arrival of the shockwave at the free face or the initial face movement. Research has consistently shown that the shockwave arrival at the face occurs before the air overpressure pulse leaves the face. Therefore, to best determine which blast mechanism contributed to the initial air overpressure pulse, testing was aimed at verifying the precise time at which the air overpressure exited the faces compared to when the face first moved. This research describes tests using scaled concrete blocks, which provided the ability to control the key parameters necessary for the research to be successfully concluded. Black powder was selected as the energetic material to eliminate the production of the detonation wave while still inducing other gas-producing effects. The components evaluated were air blast arrival times in front of the face, the initial movement of the blast face, the precise initiation time of the blast hole, timing of pressurization within the rock mass (between borehole and face, or adjacent borehole), and the speed of sound in the air. A detailed timeline was created which portrays the actions within the blast to promote an understanding of the sequencing of events. The results showed that the initial face movement occurred at 17.57 milliseconds (ms) while the calculated time at which the air overpressure exited the face occurred at 7.07 ms. The large disparity continues to reaffirm the premise that the origin fails to coincide with the air pressure pulse. Average pressurization through the block occurred at a rate of 341.23 feet per second (104.15 meters per second) which resulted in the gas release pulse being calculated to exit the face between 4.41 and 6.21 ms. This pulse correlates more accurately with the air overpressure origin timing which will be the focus of continued research. Knowing the precise origin of blast-induced air overpressure will assist in being able to better control it through appropriate blast design.

Jan 1, 2024