Search Documents

By Yuri Hovanski, Jingyi Zhang, David P. Field, Piyush Upadhyay

Friction stir welding has gained wide interest in industry and drawn large research attention due to its high level of automation and superior joint performance. In this study we further expand the welding parameters to be of magnitudes higher than those previously reported to lower the cost and enable high volume joint production. Sound butt-joints were produced with aluminum alloy 6111-T4 blanks with welding speeds up to 6000 mm/min. Tensile tests of the joint pieces show >97% joint efficiency in terms of ultimate tensile strength. The T4 natural aging and grain refinement is found to contribute to the superior joint properties. Electron backscatter diffraction (EBSD) analysis is used to qualitatively study the local shear texture inside the nugget zones of the welds. The shear texture result is a good indicator of the material flow directions in the nugget zones. The flow directions behind the rotation tool are found to be flattened towards the top surface of the workpiece when the welding speed is increased, suggesting intense material mixing and transportation along the longitudinal welding direction (WD).

Mar 1, 2018

By Yuya Nakai, Kuniaki Murase, Kazuhiro Fukami, Atsushi Kitada, Ken Adachi

Concerning nodulation in copper electrore fining, it has been reported that short circuits caused by nodulation have the largest impact on the current efficiency. Therefore, to improve the current efficiency, it is important to prevent nodulation. In this research, the nodulation growth was investigated by replicating nodulation in the laboratory. The experiments were conducted by cathodic electrodeposition on copper plates attached to copper sticks of various heights. The nodulation was analyzed in terms of growth rates versus the initial heights.

Mar 1, 2018

By Ming-Feng Ye, Guang-liang Wu

The microstructure and mechanical strength variations of chromite pellets preheated and roasted in air were studied systematically. The results show that the chromite (Fe,Mg)(Cr,Fe,Al)2O4 is oxidized to magnesium-rich (Mg,Fe)(Cr,Fe, Al)2O4 and ferrochromium complex oxide (Cr,Fe,Al)2O3 in the preheating process over 500 °C. When the temperature is higher than 1000 °C, the new phase (Cr,Fe, Al)2O3 is formed, which is mainly distributed in the outer layer of a single chromite particle. Inner the particles there are acicular (Cr,Fe,Al)2O3 and unoxidized (Fe,Mg) (Cr,Fe,Al)2O4, which forming an interwoven structure together. The oxidation rates of pellets can reach to superior limits in 20 min. With the temperature increasing from 950 to 1300 °C, the mechanical strength and oxidized rates increase to varying degrees correspondingly.

Mar 1, 2018

By Shengli Wu, Binbin Du, Mingyin Kou, Laixin Wang, Kai Gu, Shun Yao, Heng Zhou

Coke plays an important role on the actual blast furnace production (BF), and its quality significantly influences the BF ironmaking process. In this study, the effects of physical properties, chemical composition and high-temperature properties of coke on main technical indexes of blast furnace were investigated. Some coke indexes were defined to evaluate the coke quality. The main technical indexes of BF include production, quality of HM, and fuel consumption. The quantitative relationship between coke quality and main technical indexes of BF were obtained after a series of statistical analysis. What’s more, the effect of these coke quality indexes on blast furnace smelting process was also explored, and all the relationships obtained from the analysis will provide a theoretical basis for the appropriate use of coke in blast furnace. The most reasonable range of coke quality indexes can be determined combining with the actual production as well.

Mar 1, 2018

By Djalma Souza, Jean Igor Margem, Sergio N. Monteiro, Frederico M. Margem

Synthetic fibers have been used for many years to attend the demands required by the technologica lfields. However, the use of them has been questioned due to the impact on the environment. In this way, the natural fibers have received extensive attention, in particular hybrid fabrics of natural fibers to reinforce environmentally friendly polymer matrix composites. Thus, the present work has the objective of evaluating and comparing the mechanical properties of composites formed by hybrid fabric with 70% Malva—30% Jute in epoxy polymer matrix. The tests carried out are the Charpy and Izod Impact Tests, with specimens of 10, 20 and 30% in volume of hybrid fabric environmentally friendly into polymer matrix composites at room temperature. The 30% samples had the best results, functioning as an efficient reinforcement.

Mar 1, 2018

By Monica M. Jimenez Correa, Jorge A. Soares Tenorio, Denise Crocce Romano Espinosa, Paula Aliprandini

The surface zone of nickel laterite ore is generally considered as residue. However, because of the depletion of ore sources and the increase in demand, this previously discarded zone may now be processed economically for nickel and cobalt. After leaching and removal of the impurities, the solution contains cobalt, magnesium, manganese and nickel. Solvent extraction is a hydrometallurgical technique used in the separation of metals from aqueous solutions. Cyanex 272 and D2EHPA are extractants used to separate nickel from cobalt. The mixture of extractants can change the performance during the metals extraction. This work aims to evaluate the solvent extraction of nickel and cobalt when Cyanex 272 and D2EHPA are mixed. The results showed that the increased concentration of D2EHPA in the organic phase increased the extraction of nickel and magnesium. However, cobalt extraction was reduced and the manganese extraction was not altered.

Mar 1, 2018

By Mike Johnson, Greg Andrews, Niels Verbaan, Ernesto Bourricaudy, David Dreisinger

Search Minerals has developed a Direct Extraction Process for recovery of rare earths from the Foxtrot and Deep Fox deposits in Labrador Canada. The process includes crushing, acid treatment, water leaching, impurity removal, precipitation of an intermediate rare earth product and finally re fining of the intermediate product to produce a high purity mixed rare earth oxide (*99% total rare each oxides). The Direct Extraction Process has been validated in an extensive demonstration pilot plant program at SGS Minerals. A total of 3 tonnes of material was processed to produce final mixed rare earth product. The results of the demonstration pilot plant program are reported.

Mar 1, 2018

By Jose Carlos D'Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano

The production and consumption of Direct Reduced Iron (DRI) are continuously increasing, as a consequence of the impact of shale gas extraction technology on the Natural Gas (NG) market. Considering this context, DRI may improve the Blast Furnace (BF), Electric arc Furnace (EAF) and LD converter ’s productivities and consequently their competitiveness. In this work the results of a cooperative research conducted by PUC-Rio University and a Brazilian mining company are presented. Laboratory-scale simulation tests, using DR commercial pellets and typical industrial operational parameters of a benchmarked DR shaft furnace, were conducted and planned using statistical and factorial analysis. In the simulated experiments, the following three regions of the DR shaft furnace were considered: Reduction Zone (RZ), Transition Zone (TZ) and Cooling Zone (CZ). Three stages were considered in the research development: (i) the reactions and equations concerning pellet metallization and Carbon precipitation were analyzed; (ii) experiments focused on the de finition of the carburization kinetic equations occurring in the Transition and Cooling zones, and finally, (iii) aimed to develop the “METCARB” model, a computational program conceived to simulate mathe- matically the metallization and carbonization reactions along the height of the furnace. In conclusion, a comparison is made with industrial results in order to validate the resulting “METCARB” model.

Mar 1, 2018

By Zhucheng Huang, Zhikai Liang, Ronghai ZHONG, Lingyun Yi

In this work, research of reduction process was studied by means of rotary kiln (u1.5 m /C215 m) process anatomy in order to provide fine guidance to large-scale operation. It was shown that the average reduction degree of 89.96% and metallization ratio of 85.15% were obtained at the highest temperature of 977°C and total residence time of 90 min. The generation amount of metallic iron in section of temperature higher than 900°C and lower than 900°C was 34.15 and 56.38%, respectively. The section of lower temperature of 830–900 °C played an important role in formation of metallic iron, making it possible for mini-pellet to reduce quickly at lower temperature. Two main tasks were completed for mini-pellets in rotary kiln: the reduction of iron oxides in the range of 15.0–4.5 m as well as migration and bene ficiation of metallic iron, facilitating the subsequent separation of iron and gangue minerals.

Mar 1, 2018

By Maria S. Gudjonsdottir, Miao Yu, Gudrun Saevarsdottir, Pall Valdimarsson

Around half of the energy consumed in aluminum production is lost as waste heat. Approximately 30–45% of the total waste heat is carried away by the exhaust gas from the smelter and is the most easily accessible waste heat stream. Alcoa Fjarðaál in east Iceland produces 350 000 tons annually, emitting the 110 °C exhaust gas with 88.1 MW of heat, which contains 13.39 MW exergy. In this study, three scenarios, including organic Rankine cycle (ORC) system, heat supply system and combined heat and power (CHP) system, were proposed to recover waste heat from the exhaust gas. The electric power generation potential is estimated by ORC models. The maximum power output was found to be 2.57 MW for an evaporation temperature of 61.22 °C and R-123 as working fluid. 42.34 MW can be produced by the heat supply system with the same temperature drop of the exhaust gas in the ORC system. The heat requirement for local district heating can be fulfilled by the heat supply system, and there is a potential opportunity for agriculture, snow melting and other industrial applications. The CHP system is more comprehensive. 1.156 MW power and 23.55 MW heating capacity can be produced by CHP system. The highest energy efficiency is achieved by the heat supply system and the maximum power output can be obtained with the ORC system. The efficiency of energy utilization in aluminum production can be effectively improved by waste heat recovery as studied in this paper.

Mar 1, 2018

By Dachun Liu, Wenlong Jiang, Guozheng Zha, Liang Hu

In this paper, a novel technique for recovery of gallium and arsenic by thermal decomposition under vacuum is presented. The effects of distillation tem- perature on the volatilization behavior of each component were investigated. Theoretical calculations and experimental studies have shown that the method is feasible. The results show that under optimum conditions, highly pure Ga can be extractedwithadvantagesoverconventionaltechniques,includingsimpleoperation andenvironmentalfriendliness.Forexample,metallicgallium(purity > 99.99%)is obtained at 1273 K after 3 h under 3–8 Pa. Arsenic is obtained in the form of a elementary substance which could be preserved with relative ease. (cid:1) (cid:1)

Mar 1, 2018

By J. A. S. Tenorio, A. B. Botelho Junior, I. A. Anes, D. C. R. Espinosa, M. A. Caralho

Recovery of metals from reserves with low grade and from waste with high presence of contamination is a challenge to be overcome. Metals like nickel, cobalt and copper could be recovery from nickel laterite leach waste by many different processes. Among recovery processes that could be applied are ion exchange, solvent extraction and precipitation. The aim of this work was recover copper from liquor of nickel laterite by precipitation using chemical reduction. Copper concentration in liquor was 146 mg L −1 and reducing agent used was sodium dithionite 1 mol L −1. Influence of stirring speed was studied between 0–200 rpm. Results indicated a selective precipitation of copper on solution with others metals at 240 mV. The analyzes were conducted in SEM, energy-dispersive X-ray spectroscopy and XRD, that indicated presence of copper and sulfur.

Mar 1, 2018

By Haibin Wang, Baojun Zhao, Xueyi Guo, Zhixiang Cui, Zhi Wang

In conventional copper production, anode copper is produced from concentrate in three furnaces in a process that entails four oxidation steps and one reduction step. Three types of slags are produced that require further treatment to recover copper. Dongying Fangyuan Nonferrous Metals recently developed a simplified process which requires only two custom-designed furnaces instead of the conventional smelting, converting and re fining furnaces. The first furnace continuously produces high-grade matte (>75 wt% Cu) that contains little iron (<2 wt% Fe). The liquid matte is continuously fed to the second furnace, which produces anode copper. The new process signi ficantly reduces the capital and operating costs and increases productivity and environmental sustainability. This paper presents fundamental concepts that enable the simpli fied process to be developed. The detailed operations in Dongying Fangyuan Nonferrous Metals are also described.

Mar 1, 2018

By Sergio N. Monteiro, Artur C. Pereira, Foluke S. de Assis

Jute fibers are among the lignocellulosic with great potential for use in polymer composites. In this work, polyester matrix composites incorporated jute fabric were investigated for their flexural behavior. Specimens with up to 30% in volume of jute fabric were bend-tested until rupture. The results showed an increase in both the composite mechanical strength, principally to a polyester composite reinforced with 30% in volume of jute fabric. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the jute fabric and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.

Mar 1, 2018

By S. N. Monteiro, N. A. Cerqueira, E. B. Zanelato, J. Alexandre, M. T. Marvila, B. C. Mendes, A. R. G. Azevedo, G. C. Xavier

Mortar is a widely used building material and has its application in buildings in extremely vulnerable environments and susceptible to degradation, such as facades. The objective of this work was to evaluate the loss of mechanical resistance to compression and flexure and the loss of mass of the mortars with effluent sludge from paper industry, when exposed to saline environments. The specimens were done with 0, 5, 10 and 15% of incorporation in lime paste and subjected to saline mist equipment that sprays salt solution in cycles simulating natural degradation conditions using literature data. It can be concluded that mortars with a15%incorporation obtained a significant loss of mass and a decrease in their mechanical resistance, which impairs their use in civil construction and influence in other properties of the material, with a level of incorporation of 10% the results within Brazilian standards.

Mar 1, 2018

By Lingling Zhang, Daqiang Cang, Guizhou Zhao

Pilot trial ofthe detoxification ofchromium slag in cyclonefurnace and the preparation of glass-ceramics were investigated in a power plant in China. 10wt.%chromiumslagweremixedwithpulverizedbituminouscoalandlimestone as the raw materials of the cyclone furnace. Cr(VI) in chromium slag was reduced toCr O insidethecyclonefurnace.Themeltwaswater-quenchedintofritandthen 2 3 fired into glass-ceramics with a laboratory ceramicrollerkiln. The preparation and crystallization behavior of glass-ceramics were investigated with differential ther- mal analysis (DTA), physical and mechanical properties testing, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The optimal flexural strength exceeding 90 MPa were achieved in firing temperature zone of 1170–1200 °C. Anorthite (CaAl Si O ) and diopside [Ca(Mg, Fe)Si O ] can be identified in the 2 2 8 2 6 glass-ceramicsandCaAl Si O isthepredominantcrystalphase.Fineparticleswith 2 2 8 average diameter of 200 nm distributed uniformly in the glass-ceramics. Granular crystals are intensively interconnected and constituted a crystal skeleton soaked in theglassmatrix.LeachingtoxicitytestdetectedCr(VI)of0.016and0.010 mg/Lof the water-quenched frit and glass-ceramics, respectively. This method provides an effective and comprehensive technique for the detoxification and utilization of chromium slag at low cost and large-scale. (cid:1) (cid:1)

Mar 1, 2018

By Jiongtian Liu, Guihong Han, Shuzhen Yang, Yanfang Huang

Binder, as a necessary functional material of electrode in lithium ion battery, has a vital influence on the electrochemical performance. The humics, coupled with polyacrylamide (PAM) and sodium carboxymethyl cellulose (CMC), were used as a water-soluble binder for LiFePO4 (LFP) cathode using in lithium ion battery. The techniques of cyclic voltammetry (CV) and galvanostatic charge-discharge were conducted to evaluate the performance of humics binder in LFP electrode. The reversible specific capacity of LFP (HA + PAM + CMC) electrode can reach to 142 mAh g−1 after 50th cycling (100 mAh g−1) on conditions of raw materials with 1 wt% PAM addition, humics and CMC with a mass ratio of 3:1 in binder, and the raw materials mixed in an interval order. Humics has the potential to be used as a novel, eco-friendly and high-efficient binder for lithium-ion battery.

Mar 1, 2018

By Manuela Castaneda, Henry A. Colorado

This paper is about the use and stabilization of iron oxide based powders with arsenic contents coming from the purification of water. Cement paste samples with 0.0, 2.5, 10 and 20wt% of waste were fabricated by mixing mechanically all components. There are two main positive impacts of using this waste, first, this waste is produced in large amounts worldwide, and therefore the stabilization has a significant impact for the environment. Second, the waste can be used as an admixture and filler for cement, and therefore reduce the amount of cement in the concrete, which has a major impact in the CO2 footprint since cement industry produces a lot of this gas. Compressive strength and density tests were tested after 28 days. Microstructure was analyzed with scanning electron microscopy and x-ray diffraction. Results show that compressive strengths greater than 20 MPa were obtained and the samples had calcite, portlandite and ettringite phases.

Mar 1, 2018

By Marcel Magnusson, Guozhu Ye, Pekka Vaananen, Yang Tian

The most used technology for recycling of spent alkaline batteries consists of crushing, magnetic separation and processing of the nonmagnetic fraction, black mass, using a rotary kiln. In the process only zinc is recovered and all manganese in the black mass is lost. According to the EU regulation for recycling of batteries, more than 50% of batteries should be recovered. To meet the demand, Swerea MEFOS has together with a major battery recycler IsoLogistics in Finland and Sweden developed technologies for efficient recovery of zinc and manganese aiming for >50% recovery. This paper will focus on a treatment process using a DC furnace to produce a ZnO- and a MnO-product. The process has been demonstrated in pilot scale, 1 ton/h. The major outcomes will be highlighted. Another approach by using thermal vacuum technology for distillation of zinc metal has also been demonstrated in laboratory scale which is also reported in this paper.

Mar 1, 2018

By Guozhi Lyu, Ting-an ZHANG, Biyu Long, Yajing Tian, Xuejiao Cao, Weiguang Zhang

Aim to the separation problem of high concentration V–Fe in stronger acidic leaching solution of vanadium slag, a novel chelating extraction system is proposed to separate V and Fe. Influence factors including initial pH value, the extractant concentration, the phase ratio, temperature and time are investigated. The experiment results show that single extraction rate of V and Fe reach 85.57 and 0.39% respectively, when pH value is −0.4, organic phase composition is 30% Mextral 973H + 70% sulfonated kerosene oil, O:A = 1:1, stirring time is 10 min, extraction temperature is 30 °C. The industrial experiment results of three levels countercurrent extraction show that the total extraction rate of vanadium and iron can reach 97.44 and 0.23%, separation factor is 6410. The effective separation of V and Fe in high acid and high iron solution can be accomplished.

Mar 1, 2018