Search Documents

By Dale S. Preece, Lee M. Taylor

Computer simulation of the physics involved in conventional rock blasting can be split into two phases; transient stress wave propagation and rock motion. Because the two phases involve totally different mechanisms and time scales, they must be numerically modeled with two different computer programs. The first phase is usually modeled with a finite element or finite difference code which treats the rock ss a continuum and simulates the transient stress wave and subsequent fragmentation of the rock. The second phase is usually modeled with a distinct element technique where the rock mass after fragmentation is no longer treated as a continuum but as a finite number of distinct particles that interact with each other through collision mechanics.

Jan 1, 1989

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By Paul C. Miclea, Robert E. Murphy

The behavior of fire and airflows in a confined tunnel differ significantly from more familiar fire situations outside, due to the buoyant effect which tends to create a layer of hot smoke and gases flowing away from the fire near the crown of the tunnel, while air supporting combustion moves toward the fire beneath the smoke layer. A subway emergency ventilation system is designed to force air to flow through the tunnel, shifting the balance of heated air in the direction of the forced flow and avoiding the "back-layering" of hot gases and fumes. This paper presents a computer program, called the "Subway Environment Simulation" (SES), which can be used to predict airflows created by the emergency ventilation system. It utilizes the latest state-of-the-art analytical treatment of fires in enclosed spaces, including observations from mine fires and gas explosions. The program allows designers to reduce construction cost by identifying unnecessary ventilation shafts and by verifying fan capacities. In addition, the program allows the designers and operators to determine safe evacuation routes, in case of a train fire, by predicting the occurrence of back-layering. It can be used to determine when the ventilation system can control the direction of smoke movement to provide a clear and safe path for evacuating people and facilitate fire fighting operations.

Jan 1, 1989

By Thorvald Wetlesen

Computer controlled drilling is now proven technology. It was first introduced by the development of the Furuholmen system for a prototype three boom tunneling jumbo in Norway in 1978. Now, 13 rigs with this concept are in operation in Europe, 3. in mining in England and. 10 in tunneling elsewhere in Europe. The system is also adapted to roadheader guidance. Practical experience has shown that the computer control system makes it possible to drive tunnels with a more accurate contour thus reducing the total amount of rock excavated, and where a full concrete lining is required a reduction in concrete volume is achieved. The total tunneling economy is improved. In the future we expect to see a wider range of instrumentation on jumbos, from the simple direction instruments to computer guidance systems for monitoring only, as well as fully automatic drilling to a programmed drilling pattern. More compact and reliable electronics will be available. Systems with low power consumption will fit easily into flameproof applications. Cabling complexity will be reduced by connection of sensors to serial signal lines.

Jan 1, 1989

By G. Labonte

The behavior of four different redox sensing electrodes (gold spiral, black platinum, chalcopyrite, and galena) during roughing and cleaning flotation is examined and related to the flotation response. Although it is difficult to provide unequivocal interpretations of the different potentials measured, the results indicate that the solution potential (as sensed by the black platinum electrode) is different from that of the pulp potential (gold spiral) and is only weakly related to the flotation response. On the other hand, the potentials exhibited by the gold spiral and the two mineral electrodes are related to the floatation response. The gold and mineral electrodes exhibit different transcient responses during the addition of flotation modifiers (e.g. NaCN, SO2). These responses appear to be related to the reactivity of the minerals and could indicate the conditioning time required to achieve flotation or depression of selected minerals.

Jan 1, 1989

The application of Kirchoff's laws to two adjoining mine ventilation network meshes containing fans results in the construction of two general quadratic equations. These equations may be solved to give the resultant airflows and hence fan duties within the system for given network parameters and fan characteristics. This technique has a wide application for calculating the duties of fans in various combinations within a mine ventilation system. Recent difficulties in economically maintaining environ- mentally safe conditions in underground working areas distant from main ventilation fans has led to increasing interest in the use of controlled partial recirculation of ventilation. This paper develops a recirculation model which can be solved directly using mathematical techniques obviating the need for iterative techniques such as the Hardy-Cross method. The advantage of a direct mathematical analysis is that mathematical algorithms may be constructed to completely describe the ventilation system under a wide range of operating conditions. This technique is applied to controlled partial recirculation ventilation systems to demonstrate its advantages for mine ventilation planning.

Jan 1, 1989

By G E. Exedaktylos, Y Zhou

The complex and non-linear nature of blast fracturing has restricted common bract design primarily to empirical approaches. The code developed for this investigation simulates the pattern of interacting radial fractures from an array of blastholes, at various burdens and spacings, and in simultaneous and delayed modes. The resultant pattern is analyzed and a fragment adze distribution calculated.

Jan 1, 1989

By Marian Radetzki

The economic developments and industrial behavior patterns that led to a lasting excess capacity in the world non-ferrous metals industries from the aid-1970s are explored. Detailed attention is devoted to analyzing and defining crucial concepts like "capacity", "excess capacity", "capacity maintenance" and "investments". Empirical evidence of capacity utilization and capacity growth in the industries under study is provided. The coincidence of excess capacity and low prices on the one hand, and investments in capacity maintenance and capacity expansion, on the other, is seen as a consequence of substantial declines in the metal industries' investment and production costs during the period studied.

Jan 1, 1989

By A. W. Khair, S. J. Jung

"IntroductionIn a typical incremental loading test, the AE activity increases rapidly in the initial stage of the loading. It is associated with initial closure under compression of favorably oriented cracks already present, together with sliding of crack faces against each other /1/. After the initial stage, crack closure and movement largely cease and the AE activity drops to a barely detectable level /2/. In the final stage of loading test, cracking associated with the onset of inelastic deformation' occurs, and the rate of AE rapidly increases /3/ indicating an increase in the •number of events associated with higher number of microcracks. To understand better primary fragmentation process, Anderson and Ruzzi conducted tests to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool /4/. They proved that a relationship existed between the AE activity, generated during fracturing and the amount of fracture surface area created.A process of fragmentation, demonstrated by conical bits acting orthogonal to the flat surface of block of coal specimen with and without lateral confining pressure is presented here. The monitoring of AE during the fracturing process of rock/coal has been a very useful indirect method in studying fracture mechanism.Specimen PreparationLarge blocks of Waynesburg coal were obtained from a surface mine. These blocks were then out and molded to approximate dimensions of 25.4 x 25.4 x 15.2 'an (10 x 10 x 6 in.). These specimens were instrumented with three strain gages in a 45 degree rosette. One was mounted parallel to the bedding plane direction, another was tinted at an angle of 45 degree from the bedding plane direction and the third was mounted perpendicular to the bedding .plane direction. Each of the three strain gages were set 5.1 an (2 in.) away from the impact point.Typical Test ProcedureIn a typical experiment, the specimen was placed in the confining chamber.Predetermined equivalent in-situ stresses were applied to the specimen by using two sets of hydraulic cylinders. Two 1 in. thick steel plates ware positioned between the sample and the hydraulic cylinders in order to distribute the pressure uniformly over the whole surface of the specimen. The LVDT null position was adjusted with respect to the coal face. After setting the LVDT, the bit and associated weight was lifted to a predetermined height (equivalent to a predetermined kinetic energy) by a win. The three strain gages were balanced using the signal conditioner and the output was recorded by a 6 channel strip chart recorder. The experimental set-up is shown in Figure 1."

Jan 1, 1989

By David K. Crapps

The drilled shaft load tests at Port Orange were part of a demonstration project sponsored by the Federal Highway Administration (FHWA) and the Florida Department of Transportation (FDOT). Three load tests were conducted. Test 1 was a conventional test with the test shaft loaded from the top. Test 2 included an Osterberg load cell at the tip and a conventional load test from the top. Test 3 used an Osterberg load cell at the tip of a production drilled shaft. All three test shafts were socketed into limerock and were carried to failure. This paper describes the test program and presents a summary of the test results. Figure 1 presents some photographs of the load test setups and Figure 2 shows the location of the drilled shaft load tests. SITE CONDITIONS The Port Orange Bridge is located on US A1A over the Intercoastal Waterway in Port Orange, Florida (south of Daytona Beach). The new bridge will provide four lanes of traffic with a 65 foot vertical clearance for Intercoastal Waterway traffic. The channel and flanking piers will be supported by 54" drilled shafts socketed into the rock. The bridge is being constructed in two phases. The southern half will be completed first, the old bridge removed and then the northern half will be constructed. The first phase is scheduled to be opened to traffic in October 1989. Each of the four piers near the channel will be supported by 12 drilled shafts with 6 shafts per pier being constructed in each phase.

Jan 1, 1989

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By Hogan C. J

The compact BWE system set up in 1984 to mine ironsand dunes and the underlying ironsand-clay has been an effective high volume produc- tion unit for New Zealand Steel Mining Ltd at the Waikato North Head ironsand mine. The system utilising two compact S400E (0 & K) Bucket Wheel Exca- vators and a single shared Beltwagon for transfer to the shiftable bench conveyors replaced a fleet of mobile elevating scrapers when the produc- tion requirement was increased by a factor of six. A key factor in favour of the BWE system was the economic advan- tages of low unit costs for both manpower and electrical energy.

Jan 1, 1989

By M. Phillip Jameson, Paul Sennett

The beneficiation of kaolin by flotation has been practiced on an industrial level since 1961. A brief history of industrial kaolin flotation is given, with a description of the various processing schemes used by the companies that practice kaolin flotation. Some of the areas where improvements could be made in the beneficiation of kaolin are given.

Jan 1, 1989

By Y. J. Wang

This paper describes a procedure for solving the generalized system of n network equations in n unknowns considering the following ventilation variables and parameters: (a) air quantities, (b) pressure losses or gains caused by the control devices (i.e., fans or regulators), (c) resistance factors, (d) natural ventilation pressure, and (e) fan pressures (as a function of air quantities). The air quantities and pressure losses for all branches in the network are grouped into dependent and independent variables. The branches with an independent quantity are contained in a chord set, and the branches with a dependent pressure loss are contained in a chord set. In addition to the problem formulation, the solution procedure, applying the Newton method, is discussed and illustrated with a numerical example.

Jan 1, 1989

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By J. J. Schoeman

In South Africa and in the rest of the world, the two mica minerals that have the most important commercial value are muscovite and vermiculite. Muscovite has been making a comparatively small but steady contribution to South Africa's mineral exports since about 1960. Vermiculite mining and concentration were started by the late Or Hans Merensky at Phalaborwa during 1946. Vermiculite has enjoyed good overseas sales since then, and during the past four years has become an important earner of foreign currency for South Africa. The various aspects of the micas that could be of general interest are briefly reviewed, such as the history of their exploitation, their mineralogy and chemistry, and their mining, concentration, production, sales, and future

Jan 1, 1989

By [Miroslaw] M. Hajdasinski

The Payback Period (PBP) is one of the most widely applied project evaluation criteria 'in the mineral industry. As much as this criterion is liked by practitioners, it is also criticized by academicians who seriously question its validity. Inspired by this criticism, the author of this paper examines the classical definition of the PBP criterion, and formulates a new one designed for both investment and borrowing projects. It is demonstrated that the PBP, in its revised version, is free from all the shortcommings of the old one, and is fully compatible with the Net Present Value (NPV) criterion, as well as with all the other NPV compatible project evaluation criteria. Since the traditional approach to the comparison of mutually exclusive projects (MEP1s) by means of the PBP criterion has been incorrect, the paper also outlines the correct approach to this problem. Finally, owing to the fact that the PBP depends on the assumed interest rate, and using a specially developed computer program, the PBP is graphically presented, in six numerical examples, as a function of the interest rate.

Jan 1, 1989

By Wood P. D, Pettifer G. R

In the upper coal surface in the Latrobe Valley, craters known locally as fireholes have developed due to prehistoric coal fires. They can be several hundred metres across and up to fifty metres deep, and are now filled with overburden materials varying from hard baked clays to very soft lacustrine clays. In addition to reducing coal reserves, continuous mining operations are seriously affected by fireholes. Large undulations in the upper coal surface result in a mixture of coal and overburden on the upper mining levels. The very soft lacustrine clays are unstable in the mine batters and the overburden dump, are difficult to handle on the bucket wheel excavator/conveyer system, and have insufficient bearing capacity for the large bucket wheel excavators. Early identification is essen- tial and both drilling and dynamic core penetrometer have been exten- sively used. However, this has not proved adequate in locating and defining the extent of all fireholes, due largely to their irregular shape. To overcome this a range of geophysical techniques has been trialled with very promising results. A trial area has been covered on a twenty metre grid using gravity and Geonics EM34 conductivity measurements and the same area has been covered at a closer spacing with high resolution magnetics. Image processing of contoured magnetic, EM34 conductivity and residual gravity data has resulted in very good correlation with drilling data.

Jan 1, 1989

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1987 was $446.6 million, an increase over that of 1986 and the first increase in 3 years. Alabama was second in the Nation in production of bauxite and ferroalloys; third in bentonite, crushed dolomite, crushed marble, and fire clay; and fourth in masonry cement. Trends and Developments.-Employment in the minerals industry remained relatively low for the second year even though the overall unemployment rate dropped to 7.9% by December. Employment in mining and primary metals dropped about 10% and 2%, respectively.

Jan 1, 1989

By Palmer G, Dennis R, Clark A

The Ravenswood Mine in North Queensland is the first gold mine developed by Carpentaria Gold Pty Ltd, a wholly owned subsidiary of MIM Holdings Ltd. Carpentaria Exploration Pty Ltd began exploration at Ravenswood in 1978. However initial exploration of the main gold producing area (Buck Reef East) commenced in March 1987 when exploration rights to four key leases were secured. A rapid, co-ordinated exploration and development program produced gold from a heap leach operation nine months after the first costeans were dug at Buck Reef East. To treat higher grade ore found at depth in the Buck Reef East pit and the metallurgically more difficult Buck Reef West ore, a carbon in pulp plant was commissioned in May 1988. The mine is currently producing at a rate of approximately 40 000 ounces of gold per year. Ore at Ravenswood is hosted by hydrothermally altered diorites and tonalites of the Ravenswood Granodiorite complex. Alteration is controlled by planes of permeability formed by joints, shear zones and dilational breccias. The complex orebody geometry resulting from these controls required very detailed surface and drill exploration for adequate definition. Carpentaria's need for early cash flow meant that economic, mining and metallurgical considerations governed choices of exploration techniques, program timing, material and data collected. The initial reserve of 1.1 mt @ 2.87 g/t Au was defined by sectional polygonal methods. Grade control is based on geologic mapping and blast hole or channel sample assays. Ore is batched through the crusher and sampled to monitor grade control and mining performance. Minimal dilution has occurred. Gold content is greater than predicted by the reserve. Sprinkling of heaps commenced in November 1987. Changes have been made to the pad design and to the method of heap construction. Heap leach ore is treated at a rate of 400 000 tpa.

Jan 1, 1989