Search Documents

By S. Mathur

The southern Florida phosphate deposits that will be mined in the future contain significant amounts of dolomite. Because high MgO levels are undesirable in phosphoric acid production, several flotation schemes for the removal of the dolomite have been attempted. Alternatively, selective flocculation has been suggested as a potential process. A high MgO rock was simulated with a 30:10:60 mixture of apatite, dolomite and silica, respectively. Single mineral selectivity was observed in the apatite-silica and dolomite- silica systems using Polyacrylic acid (PAA) and Poly(ethylene oxide) (PEO) flocculants, respectively. However, no single mineral selectivity was observed in the apatite-dolomite system using PEO. Heteroflocculation, suspected to be the major reason for the loss of selectivity, was minimized by the addition of a site blocking agent (SBA), consisting of a lower- molecular-weight fraction of PEO. Process parameters such as size reduction schemes, flocculant/SBA dosage and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed-mineral tests was also achieved in the ternary mixed-mineral system, namely, the apatite-dolomite-silica system. In this report, surface chemical characterization of the samples and their flocculation behavior are discussed.

Jan 1, 1995

By G. Lee, E. T. C. Spooner

"Molybdenum mineralization at Boss Mountain is hosted by the Triassic Takomkane quartz monzodiorite batholith and is associated with a Cretaceous monzogranite stock. Ore has been mined from a sheeted vein system that describes a partial annulus centred upon the apical region of the stock and from subvertical breccia pipes that emanate from the stock. Molybdenite precipitation is coincident with CO2 effervescence from a dilute (1.9 mole o/o NaC/ equivalent) hydrothermal fluid over a temperature range of 250°C to 370°C at a pressure of approximately 350 bars, interpreted to be greater than or equal to the lithostatic load and equivalent to a depth of 1.3 km or less.IntroductionThe chemical and thermal constraints on molybdenum transport and deposition to form molybdenum ore deposits are not well understood. To address this problem, the Boss Mountain mine in central British Columbia, operated by Noranda Mines Ltd., was chosen as a well-described (Soregaroli and Nelson, 1976), relatively small and simple example of a Cordilleran Mo~ deposit. It is situated on the northeast slope of Takornkane Mountain, 10 km west of the community of Hendrix Lake (N.T.S. 93A/2W; latitude 52°06'N, longtitude 120°56'W). Access is from 100 Mile House by nearly 90 km of road, the first 50 km of which are paved."

Jan 1, 1995

By Moore A. J

This paper describes the use of a wavefront reinforcement model which has been developed to supplement established charge mass scaling methods. The model allows for the time taken for blast vibration wavefronts to travel from each blasthole, and has been successfully used to explain the reason for directional increases in both air and ground vibration in certain situations. The model has been used to identify wavefront reinforcement due to the propagation of air vibration and ground vibrations in certain situations. The paper includes a throw (or cast) blasting case history which provides multi-station evidence of the strong directional nature of wavefront reinforcement.

Jan 1, 1995

The Olympic Dam mining operation is some 520 kilometres NNW of Adelaide on the Roxby Downs Pastoral lease. The deposit containing copper, uranium, gold and silver was discovered in 1975 by Western Mining Corporation (WMC). A joint venture was formed in mid-1979 between WMC (51 per cent) and British Petroleum (BP, 49 per cent) for the development and exploitation of the deposit. WMC assumed 100 per cent ownership after acquiring BP's share in early-1993. Ore is won from a highly mechanised underground mining operation and processed to refined products. Current annual output from the mining of 3.0 Mt of ore is approximately 83 500 t of refined copper, 1400 t of uranium oxide, 750 kg of gold and 12 000 kg of silver. Conventional long hole, open stoping techniques are used to extract the production ore. Since stope production began in April 1988, full surveys and appraisals of stopes have been carried out to evaluate the integrity of the design and blasting techniques. This evaluation included the determination of the degree of dilution or non break that had occurred. Performance information also made it possible to re-design any adjacent stopes to retrieve remaining ore and conversely, avoid the chances of targeting backfilled material in the future. Performing stope surveys proved not only to be a time-consuming process but one fraught with access and line-of-sight problems. Occasionally it was not possible to obtain any stope survey data, and as was often the case with the mine pass system, rarely. In 1992 the sudden failure of the pillar between the fine ore and mullock passes and the subsequent delays to production, emphasised the need to effectively monitor pass wear. Initial information regarding the development of the Cavity Measurement System (CMS) prototype (Figure 1) indicated that it had the potential to solve these problems by the introduction of a remote scanning device into a cavity. Following a great deal of investigation, Olympic Dam Operations purchased the first CMS in Australia. This paper discusses its application for all underground void surveys and the procedures developed to manage both field and office requirements.

Jan 1, 1995

By Colin E. Dunn

Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

The geological features of the destructive plate margins of the southwest Pacific favour the formation of porphyry type deposits. The major controlling factor favouring the formation of gold-rich deposits of this type is a dense crust. This results in shallow intrusion of large magma bodies beneath andesite stratovolcanoes. Where the intrusives have near vertical sides, the comparatively low temperature of transfer of volatiles from the solidifying melt favours the partitioning of gold into bubbles of volatiles. They reduce the viscosity and density of the melt, resulting in the upward movement of a mineralised melt. With the drop of pressure with upward movement the bubbles separate into a two phase mixture, triggering freezing of the mineralised melt and the formation of a gold mineralised stockwork.

Jan 1, 1995

"The Crescent, DM, and Pothook zones are copper-gold porphyry deposits which formed in association with alkalic intrusions of the early Jurassic Iron Mask batholith. The characteristics of the Crescent and DM deposits are nearly identical. Both formed along the contact between the Cherry Creek monzodiorite and Pothook diorite phases of the batholith. Permeable intrusion breccias along the contact concentrated the flow of hydrothermal fluids. Early, pre-ore alteration is represented by pervasive, sulphide-barren potassium metasomatism. The precipitation of copper-gold ore occurred during subsequent fracture-controlled potassic alteration, and is most strongly developed in chlorite-sulphide veins and their alteration envelopes. A central zone of potassic alteration is surrounded by a propylitic, pyritic halo in both deposits. The DM zone is unique among alkalic porphyry deposits in its high abundance of quartz-sulphide veins.The Pothook deposit formed at the westernmost contact of the Iron Mask batholith with enclosing Nicola Group volcanic rocks. Pervasive potassium metasomatism, similar in style to that at Crescent and DM, is associated with intrusion of the Cherry Creek monzonite. Pervasive and fracture-controlled albitic alteration is associated with intrusion of the Sugarloaf diorite and introduced minor copper-gold mineralization. Most of the copper-gold mineralization was introduced during formation of veins and breccia matrices dominated by magnetite/hematite and sulphide. Late-stage chlorite veining may have remobilized or introduced additional gold mineralization.Copper and gold assays in the Crescent deposit are well-correlated and have a nearly constant Cu:Au ratio, suggesting that the metals coprecipitated during a single hydrothermal event. In the Pothook deposit, copper and gold do not correlate closely, lack spatial correspondence, and suggest that transport and/or deposition of the two metals were not identically controlled and that they may have been introduced at different times by separate hydrothermal events."

Jan 1, 1995

By Alexandr A. Abramov, Svetlana M. Angelova, Oleg P. Maljuk

In this paper the effect of the ratio of grinding and grindable size classes (ore lumps, particles and grains) and the guantity of intermediate size classes in the feed of the primary wet autogenous grinding "Cascade" mill is studied and the features of the influence of these factors on the mill capacity are shown. On the basis of the experimental data from Lebedinsky mineral processing plant, where magnetite guartzites are processed, a coefficient of the "total ratio of size classes" in the feed of 9x3 m "Cascade" mill was estimated. It helps to get an evaluation of the effect of ore size classes ratio in mill media on the mill capacity and to work out some ways for its optimization in closed or semiclosed technological circuites of primary autogenous grinding. The operation of the specific energy effects for some intermediate size classes, removed from the mill as circulating load, is proposed to improve its efficiency before regrinding in "Cascade" mill and decrease negative influence of such classes accumulation in the mill media.

Jan 1, 1995

By Hal dun Kurama

In thus-study, Bigadic upper zone zeolitic tuff, which contains about 87% clinoptilolite was used as an ion exchanger for removal of Pb++, Cu++, Cd++ and Hg++ ions from wastewater. Bench scale experiments with two different glass columns, were carried out continuously under the closed/ open circuit conditions. Before ion exchange tests, zeolite samples were treated with NaCI (6ml/ min. and 42BV). The effects of particle size, bed volume, pH and flow rate on the ion exchange capacity were determined. Under the best operation conditions, the effect of initial influent solution concentration on ion exchange selectivity was tested. As a-result, it was found that the Bigadiç clinoptilolite had the following ion exchange capacities;

Jan 1, 1995

By Roger A. Bullivant

The introduction of this size and type of piling rig is intended to address a multipurpose foundation activity. The 8000 denotes the size of equipment that is attached to the mast, namely 8000 Kg. Larger equipment can be carried subject to adjustment of rig geometry. The 8000 series rig will easily accept hydraulic piling hammers and CFA equipment, but for the purpose of this discussion it will be equipped with an auxiliary power pack that is matched to twin vibrators. The design of the siamesed vibrators allows long tube equipment or piles to be driven with a short mast configuration that provides a lower overturning risk. It is easily adapted within minutes to carry out other foundation requirements that are required on the same contract. The piling and ground consolidation activities that can be undertaken by the 800 series machine are:-

Jan 1, 1995

By I. A. H. Schneiderl

Eichhornia crassipes approaches being a scourge in many parts of the world, .choking waterways and hindering transport upon them. At the same time it is known to readily abstract heavy metal ions from water and, thus, aids in the removal of heavy metals found in such waters. This paper considers the possibility of using specific parts of the plant as an inexpensive adsorbent for the removal of heavy metals from contaminated chemical and mining industry waste waters. In particular the root of the plant was found to be an excellent accumulator of 'heavy metal ions including uranium from solution. It is. also suggested that dried roots of the plant ?might be placed in simple bags and used in a very low cost metal ion removal system.

Jan 1, 1995

By Roy J. M. van Lier

In industrial aqueous solutions, germanium generally occurs in trace amounts amid high concentrations of other metals, such as zinc, copper and iron. Separation of germanium from these metals as well as its isolation from gallium and indium pose a real challenge to the hydrometallurgist. After a brief discussion of the aqueous chemistry of germanium, this paper reviews the flowsheet of the Apex Mine in Utah. The Apex property was the only mine in the world to be operated primarily for production of gallium and germanium, but apparently closed due to great operating difficulties. Several process variants proposed for the treatment of the Apex ore, including bioleaching methods, are addressed. Following a more general description of the behavior of germanium in hydrometallurgical zinc processing streams, available technology for its recovery from aqueous solutions is summarized. Precipitation, solvent extraction, ion exchange, electrowinning, ion flotation and liquid-membrane separation are all outlined in terms of the aqueous chemistry of germanium. Finally, the production of high purity germanium dioxide and metal is briefly discussed

Jan 1, 1995

By M. S. Enders

The McDonald gold deposit is located in the upper Blackfoot Valley in Lewis and Clark County in west-central Montana, about 65 km (40 miles) northwest of Helena and 13 km (8 miles) east of Lincoln (Fig. 1). The McDonald project area covers about 20.7 km2 (8 sq miles) of elevated terrain on the north side of the Blackfoot Valley. The Blackfoot River lies 1 km (0.6 miles) south of the McDonald deposit. East Butte and West Butte rise 300 m (985 ft) above the Blackfoot Valley to an elevation of 1,750 m (5,740 ft). They conveniently divide the area into two parts. The Seven-Up Pete Joint Venture (SPJV) is a partnership between Phelps Dodge Mining (72.25%) and CR Montana, a subsidiary of Canyon Resources (27.75%). SPJV controls about 83 km2 (32 sq miles) of mineral and surface rights in the Lincoln area. The McDonald project is on state-owned and private land. The joint venture has conducted exploration since 1989 at the Seven-Up Pete, McDonald and Keep Cool areas (Fig. 1).

Jan 1, 1995

By S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. Currently, the major markets for scrubber sludge are for manufacture of gypsum products, such as wallboard and plaster, and for cement. However, the quality of the raw sludge is often not high enough or consistent enough to satisfy manufacturers, and so the material is difficult to sell. Other markets, such as paper manufacture and plastics fillers, have even more stringent quality requirements and will not accept raw sludge at all. In the work described in this paper, several reagents have been examined to determine their ability to selectively improve the flotation of the unreacted limestone contaminant away from the desirable products (calcium sulfite and gypsum). The most success has been achieved using a cationic collector, which shows a higher selectivity between calcium sulfite and calcium carbonate than do the anionic collectors that were studied.

Jan 1, 1995

The subject `access to land' is often seen as an item high on the list of matters of concern to mining interests not only in New South Wales but throughout the whole of Australia and other countries. Just what are the problems/issues of access to lands today? What is being done about them? What can be achieved? What is practical to achieve? And where does New South Wales sit in relation to all this? These and a range of other issues are addressed in this paper.

Jan 1, 1995

By John E. Urosek, Timonthy R. Watkins

Room and pillar mining accounts for approximately 73 percent of the active gobs used in the United States in 1993. The Mine Safety and Health Administration conducted field investigations on six different types of bleeder systems used to ventilate areas mined by room and pillar methods. This paper discusses investigations that were conducted at mines using four of these systems.

Jan 1, 1995

By G. E. Agar

In the April issue of Mining Engineering there is a technical note "New size laboratory ball mill for Bond Work Index determination" written by M. Nematollahi which is very confusing. My recollection is that a description of an experimental procedure should be such that someone skilled in the art should be able to reproduce the results. Applying this test to this particular article would according to me cause a failure to be registered. There are apparently three batch laboratory test procedures referred to in the article. One of these is the traditional Bond test with all its limitations such as dry grinding followed by exclusively dry screening, two attributes which fail to simulate conventional industrial grinding. There is a second procedure (NSBM) which the author is advocating as an improvement of the Bond procedure but from the description I doubt that anyone would be able to repeat the procedure. For instance, is the grinding to be done wet or dry, if wet at what pulp density, and how is the screening to be done, wet or dry or a combination?

Jan 1, 1995

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver's cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek – Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern BlackHills or other areas of similar geologic settings."

Jan 1, 1995

By C. T. Philipp

Recycling of waste is much preferred over disposal. This paper discusses the Enviroscience, Inc. (ESI) process, now being commercialized by MetWool, Inc., to recycle hazardous wastes using an extractive metallurgical process which is followed by vitrification of non-reducible metal oxides. In this process, volatile and reducible metals are reclaimed as their respective oxides and elements.

Jan 1, 1995