Search Documents

By Hans E. Madeisky, Bruce W. Downing

Abstract-The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: anorthosite-hosted magmatic sulfide nickel, dunite-hosted magmatic sulfide nickel, porphyry copper-gold, and volcanic-hosted high sulfidation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray fluorescence equipment, already used for grade control at many mine sites, could provide the wholerock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By G. M. Card, K. D. Card, B. V. Sanford

The Canadian Shield and its extensions are traversed by an orthogonal system of north-west and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches in?uenced patterns of sedimentation and tectonism in the intervening epicratonic basins andmarginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structuresalso triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By B. Yarar, R. Buchan

Mineral-processing techniques were adopted for use in the separation of various plastics used in beverage bottles. A complete flowsheet, which utilized size reduction, heavy-media separation and flotation, was developed to separate PE, PVC and PET. In addition, the mixtures contained cellulose fibers (from labels) and aluminum (from bottle caps). It was demonstrated that, while heavy-media separation allows for the separation of a PVC/ PET mixture, froth flotation can be used to separate PVC and PET. For this purpose, the differential action of a pH 11 alkaline aqueous solution containing methanol and MIBC as surface-tension control agents, has been found to be a suitable flotation medium. This paper reports on some aspects of a flotation flowsheet that was developed for the separation of plastics contained in municipal solid wastes.

Jan 1, 1997

Develop geophysical techniques suitable for enhancing miner safety. Specifically, to use geophysical methods to detect hazardous conditions in a rock mass in deep underground mines as well as to assess the mechanical integrity and monitor changes of the rock.

Jan 1, 1997

By John S. Livermore

I feel very privileged to be added to the distinguished group that has received this award since the first recipient, Reno Sales, received it in 1954. If my research is correct, the last geologist to be honored was Bill Callahan in 1982. Perhaps the Awards Committee decided it was about time to select a geologist, and I became the beneficiary. Regarding the discovery of the Carlin ore body, it was the culmination of several studies - one going back as far as 1939 when a US Bureau of Mines engineer named W.O. Vanderberg recognized an unusual type of gold mineralization in sediments in northern Nevada. What was unusual was the fact that the gold was so fine that it would not concentrate in a pan. This, plus the study of the Roberts Mountain thrust by Ralph Roberts (1960) and conversations with Harry Bishop, manager of the Gold Acres Mine, pointed Alan Coope and me in the direction of the Lynn Window and, eventually, the Carlin discovery. There has been a great deal written about this discovery. I thought it would be interesting to discuss the evolution of Carlin gold exploration in Nevada since this time and to discuss the changes in perception of this unique type of mineralization. The method used by Coope and me in following up on Roberts' work was to map geologically the Roberts Mountain thrust and conduct geochemical sampling of favorable outcrops and float. Coope was highly experienced in geochemical exploration, as he had graduated from the Royal School of Mines in London, studying under John S. Webb, one of the pioneers of geochemistry as applied to mineral exploration. We first considered using pathfinder elements, but finally concentrated on gold analyses alone, even though the sensitivity of fire assays used at that time was only about one-half part per million. According to the spatial relationship of the mineralization to the Roberts Mountain thrust, as pointed out by Roberts (1960), we were looking for mineralization within the thrust itself. Our models were the known Gold Acres and Getchell mines, which contained reserves on the order of 0.9 to 1.8 mt (1 to 2 million st). These were not of substantial size, but I had hoped we might find more than one of these tributary to a mill that would justify an operation for our employer, Newmont Mining Corp. What we ended up with was the type of deposit we were looking for - an open pit deposit of micron gold, which the old timers had missed because the gold was not capable of being panned. But never in our wildest dreams did we think there was a chance of finding a body containing 10 mt (11 million st) of ore at 0.30 oz/st (10.3 g/t).The deposit was not in the thrust proper but was found in a favorable horizon of Roberts Mountain siltstone that was below the thrust. This is the first example of how a model should not be followed blindly. Newmont was successful in keeping this discovery quiet for some time. After a considerable amount of drilling, a rumor circulated that they had discovered a large low-grade ore body of around 1.7 to 2.1 g/t (0.05 to 0.06 oz/st), which of course would not have been economic with gold at $1.13/g ($35/oz), which was the fixed price at that time. The company, for obvious reasons, did not discourage the rumor. When, however, the true results came out there was a lot of feverish activity. Because of this new type of so-called "invisible gold," which could have been missed by the old timers, the thought was that other deposits would be discovered very soon. The Carlin and other smaller deposits, including Bootstrap, Blue Star and Gold Quarry, were in windows where the lower plate of the Roberts Mountain formation (below the thrust) had been exposed by erosion. This then became the new

Jan 1, 1997

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By R. A. May, P. J. Brooks, W. M. Smith

"Neill and Gunter Limited (NGL) has prepared a preliminary design and a cost estimate for a ferric chloride leach plant to recover copper, lead, zinc, and silver from a typical complex sulphide ore. This plant design is specifically intended to treat unconcentrated ground ore (flotation feed), but can be readily adapted to treat bulk concentrates. Samples of ground ore and bulk concentrate were obtained from Heath Steele Mines, Miramichi, New Brunswick, laboratory testing, and preliminary process flow sheet preparation was carried out by the Research and Productivity Council in Fredericton, New Brunswick. Approximately thirty drawings have been produced, including process and equipment flowsheets, process piping and instrumentation drawings, and preliminary general arrangements. Preliminary capital and operating cost estimates were prepared for a plant that would treat 1000 t/d of crushed and ground ore to produce about 30 000 tpy of zinc. Capital and operating cost estimates were also projected for plants up to 4000 t/d of processed ore. Recoveries of 99% for zinc, 98% for lead, and 96% for copper were achieved in laboratory tests on unconcentrated ore. These recoveries were higher than the overall recoveries obtained from bulk concentrate, yielding approximately 10% more revenue.A 1000 tonne per day plant was determined to have a low return on investment, however, depending on the size and type of mining operations employed and the FCL plant throughput. DCF-ROI projections of 20% to over 30% were calculated for 100% equity financed “green field” mine, mill and FCL plant operations of 2000 t/d and higher"

Jan 1, 1997

By R. C. Hubli

A chemical model has been developed to investigate the dissolution of sulphide minerals in brine solutions containing copper and iron chlorides. The model has been employed to study the dissolution .of synthetic NiS using different initial concentrations of Cu(II), Cu(I), Fe(III) and temperature. The speciation of copper with particular reference to the formation of hydroxy-chlorides as a function of total chloride and H+ has been computed. The model predictions are in agreement with experimental results. It has been found that addition of Fe(III) results in the maintenance of a high Cu(II)/Cu(I) ratio leading to enhanced rates of dissolution and suppresses the loss of Cu(II) due to the formation of hydroxyl-complexes.

Jan 1, 1997

By R. Burns, A. I. A. Salama, M. W. Mikhail

"Large amounts of oil sand tailings are produced in the Fort McMurray area, including sand, clays, and misplaced bitumen. The objective of the present study (as part of the overall engineered tailings program) is to select and evaluate the role of hydrocyclones in removing most of the solids from the tailings slurry and producing an underflow product containing about 75% solids.Multistage cyclones were evaluated in pilot plant tests. Slurry feeds with different percents solids and increasing ratios of superfines (–44 µm) were used in testing multistage cyclone circuits. A two-stage Linatex separator circuit gave high recovery to the underflow of 98.8% to 99.6% by mass with the desired high solids content in the underflow of 73% to 75% by mass. Changes in feed solids content (20% to 50%) had little or no influence on cyclone underflow recovery and solids content. The keys to achieving such results were the apex control mechanism and operation at relatively low feed pressure (<60 kPa for 23 cm F cyclone) when the feed solids content was high. Increasing superfines above 7% by mass in the feed resulted in a significant reduction in the recovery to the underflow, probably due to the heavy medium generated by excessive amounts of clays in the cyclone. Pilot plant results were better than those predicted by available cyclone simulation models in terms of recovery and solids concentration in the underflow.Increasing cyclone diameter from 23 cm for the Linatex separator to 51 cm for the Krebs cyclone appears to have little or no effect on size cutpoint."

Jan 1, 1997

By M. Suzuki, M. Dobashi, M. Kahata, T. Yoshida

Almost 30% of steel in Japan is produced by electric arc furnace (EAF) treatment of iron scrap. EAF dust includes approximately 20 wt % of Zn and 3- 5 wt % of CI and is treated by the pyrometallurgical processes to recover Zn as Zn oxide. Direct hydrometallurgical processing is one of the most effective methods to recover high purity Zn. In this case, CI in the EAF dust is dissolved in the liquid phase by leaching, and the CI anion in electrolyte attacks anodes which are commonly made of a lead base alloy. Several processes have been proposed to remove CI anions from acidic sulfate solution. In this study, an electrolytic process was examined to eliminate CI anions from Zn sulfate electrolyte. From our study it can be said that the elimination rate of CI anion depends on the anode material ( i.e., the elimination rate is Pb-Ag alloy == Pb > DSE== Pt). In industrial Zn electrowinning process, the electrolyte contains Mn, which means the influence of Mn should be considered in the elimination of Cl. Mn dioxide deposition on an anode plate reduces the efficiency of CI removal. A periodical reverse current electrolytic system was examined to prevent this efficiency decrease, and deposited Mn dioxide could be removed very rapidly when the current is reversed. More than 95% of CI anion could be removed by this method in a shorter period than direct current method.

Jan 1, 1997

To provide an engineering solution to wood crib design and deployment strategies that will ensure safety for underground coal mine workers. This is accomplished by preserving necessary ground control requirements while minimizing support costs or by developing new support strategies to enhance ground support in difficult conditions. A secondary objective is to be able to quantify wood crib support performance to define support requirements for alternative support systems. These objectives have been achieved through a simple-to-use computer program called the wood crib performance model (wcpm).

Jan 1, 1997

By T. Acton

The Zarafshan/Newmont Joint Venture is currently operating in the Republic of Uzbekistan producing in excess of 400,000 oz. of gold per year from low grade oxide ore stockpiles adjacent to the Muruntau open pit gold mine located in the Kyzylkum desert of central Uzbekistan. Four stage crushing and screening produces a final product for heap leaching, Merrill-Crowe processing, and local refining for International market export. The Zarafshan/Newmont Joint Venture is the first major commercial project of its kind in the former Soviet Union to be successfully negotiated, engineered & constructed, and placed into continuous operation,

Jan 1, 1997

By C. J. Bise

Virtual reality (VR) is a concept in which the human experience of perceiving and interacting with a computer-modeled environment is achieved through the use of sensors and effectors. It is an advanced form of computer graphics. The images are generated based on where the user looks and how the user moves. As personal-computer-based (PC) instruction gains acceptance as an innovative approach to providing safety training, VR can provide a multisensory, rather than merely a multimedia, mode of presentation. New technology continues to be introduced into the mining industry to meet the productivity needs of coal and noncoal producers. There is also an increased need for more innovative training of mine workers. New technology and equipment designs often affect the basic causes of accidents. For example, the development of cabs and canopies for underground coal-mine equipment has reduced the number of accidents related to roof falls and rib rolls. However, safety-training specialists then had to focus on the machines themselves, because the modifications had the potential for causing "pinch-point" accidents. In fact, although the overall physical demands on mine workers have diminished, there has been an escalation in the concerns about trauma from repetitive physical activity. Thus, health-and-safety training specialists have shifted their atten¬tion to the recognition, evaluation and control of workplace hazards (Hancock and Hill, 1995). Recognizing that the spatial relationships of a workplace convey more information about hazards when experienced rather than described, trainers agree that simulation is the method of choice. Unfortunately, until recently, simulation systems were either simple software programs that did not come close to portraying the real experience or were complex hardware systems (such as flight simulators) that did, but at a cost of millions of dollars (Fritz, 1991). However, researchers and training specialists are excited about an emerging approach to work-force education based on virtual reality. VR is also described as cyberspace, immersive simulation, artificial reality, telepresence, virtual environment or virtual world (Meyer and Dunn-Roberts, 1992; Peterson, 1992). It represents a group of concurrent advances in computer and interface technologies. They enable an individual to interact in a multisensory way with a computer-generated environment. To achieve this, a typical VR system incorporates a computer that contains the necessary databases for producing realistic images and audio; a head-mounted display (HMD) or screen for viewing the images; and a three-dimensional controller, joystick or data glove for interacting with the computer-generated environment. If virtual reality is to become an effective tool for the safety training of mine workers, its attributes will have to be measured against other forms of delivery. Accordingly, Carr (1992) listed the following areas in which VR should be considered the method of choice: ? When training mistakes would be costly. ? When the necessary environment cannot be experienced in the real world. ? To build interfaces that are sensible and can be manipulated. ? To make training situations really "real." ?To make perceptible the imperceptible.

Jan 1, 1997

By Seymour D

The disagregation and privatisation of the mining and power gene ration operations of the former State Electricity Commission of Victoria has being taking place over the past five years. This has transformed the service provision to the new organisations and has resulted in major change to the working lives and professional relationships of thousands of Australians. The authors wish to take this opportunity to explore the issues arising as the program of privatisation of public assets continues. Changes within the workplace which resulted from the outsourcing of the &apos;investigation and design&apos; functions and more lately as a result of privatisation of the operating, generating and distribution businesses are discussed. The responsibility of managers retaining the services of design engineers has changed. There is an added responsibility of contract administration and an increased focus on intellectual property and strategic issues. The way in which the sectors are adapting is discussed and future directions are explored. We welcome this opportunity to explore the changes in professional life which have taken place over the last five years in the Latrobe Valley Power industry. Engineers and earth scientists have a pivotal role in the continuing successful operation of the three Latrobe Valley Mines of the generation companies. The Mines&apos; collectively excavate annually over 13 million cubic metres of overburden and 48 million tonnes of coal for delivery to mine-mouth power stations and for briquette manufacture.

Jan 1, 1997

By D. Lelinski, R. Bokotko, J. D. Miller, J. Hupka

Air-sparged hydrocyclone (ASH) flotation is a new, promising technology, and, since its conception, numerous applications have been successfully tested. Nevertheless, research and development efforts have continued to improve the technology with respect to operating conditions and design considerations. Results, from experimental studies on bubble generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation were determined using a high-speed photographic technique. The influence of many factors, including surfactant concentration, water flow rate, and porous-tube pore size have been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flow rate (shear field), the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions, the average bubble size was found to range from about 100 to 300 µm in diameter.

Jan 1, 1997

By M. Jaramillo

The expanded west pit of the 15 Mta (13.6 stpy) El Cerrejon mine will eventually reach a maximum depth of 270 m (890 ft). Slope-stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization calls for anchoring the footwall by the installation of 9- to 33-m- (30- to 108 ft-) long multistrand steel cable bolts. For each of the 15-m- (50-ft-) high mining benches, a row of bolts is installed with variable horizontal spacing, depending on the dip magnitude. Cable bolting is now standard operating practice, and an estimated 11,800 bolts will be installed during the life of the mine. Results to date have been satisfactory in terms of the stability condition of the bolted slopes.

Jan 1, 1997

By Richard Snyder

Secretariat of the Coal Mining and Mining Executive Committees&apos; of the National Safety Council (NSC) and Manager of the memberships to both Mining Sections; Senior Consulting Safety Engineer, NSC; member of several committees for consensus Standards of the American National Standards Institute (ANSI); a Certified Safety Professional (CSP) of the Board of Certified Safety Professionals of the Americas, Inc. and a chief proctor for CSP testing and certification procedures, et al. It appears that the tunneling trade is merging into its own renaissance for the decade of the 1970s&apos;, and most likely on past the year 2001. Federal interest in underground excavation, and more specifically, rapid excavation expertise has been on the upswing since the latter part of the 1960&apos;s, mainly due to the pressing national needs for more raw materials based on the rise for material goods and the projective gloom of possible power shortages. On the pure tunneling side the national needs encompass, in the mainstream of priorities, rapid transportation and water supply excavation as the two top contenders. For instance, the estimates for tunnel mileage for the period 1968-1975 are:(1) Subways---85 miles Urban Highways--- 123 miles Intercity Highways---210 miles Water Supply Routes---528 miles at a total of 946 miles of tunnels. The estimated cumulative underground excavation demand in dollar amounts for the period 1970-1989 are:(1) Construction Oriented Demand--- $35 billions Mining Oriented Demand---$34 billions (which includes the coal-oriented demand on the order of 26 billions.

Jan 1, 1997

By Roy Moreby

Dartbrook Coal is currently developing a modern, high production (3.5 Mtpy) single longwall retreat coal mine in the Upper Hunter Valley of NSW, Australia. The location is a green field site, with no surface or underground mining operations ever having taken place in the initial target seams. The coal seams of the working section, floor and immediate roof average a total 20 m in thickness and contain a mixed carbon dioxide 1 methane seam gas ranging from 6.5 to 11.0 m3/t. The target seams have undergone detailed characterisation to assess hazards and quantify the controls required to minimise associated risks during mining. Risks identified during initial phases of exploration and 14 months of development include: • High gas emission during development. • Probable high longwall gas emission rate. • Medium to high propensity to spontaneous combustion • Possible carbon dioxide outbursts on geological structures • The main controls currently in place include, • Mine geometry and ventilation circuits • Exploratory drilling ahead of development • Intensive in seam pre drainage • Goaf drainage plants • Comprehensive monitoring systems • Underground environmental management plan. • Pre mining predictions of gas emission provided an indication of gas emission rates which have proven to be an under estimate. Current mine issues are; • Both surface fans are at full capacity (250 m3/s 1.4 kPa) • Both gas drainage pumps are at full capacity (2.3 m3/s) • Alternatives to extensive in seam pre drainage being investigated (surface to in seam hydro fracture) Review of mine design underway This paper describes the seam characterisation, assessment of mining hazards and summary of the management plan developed to address the risks identified. A review of current mine underground environmental performance is also provided

Jan 1, 1997