Search Documents

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

By Sevket Acar, Tim Acton

"Zarafshan/Newmont is a 50/25/25 joint venture between Newmont Gold and the State Committee for Geology and Mineral Resources, and Navoi Mining and Metallurgical Combinat, two entities of the Republic of Uzbekistan. The Zarafshan/Newmont joint venture consists of a heap leaching operation which will process 220 million metric tonnes of existing low-grade oxide ore stockpiles (averaging 0.036 oz Au/t) from the Muruntau mine. Net recovery over the 17-year life of the project is expected to be 4.8 million ounces of gold.The plant construction started in October 1993 and operations commenced on May 25, 1995. The crushing plant consists of four stages of crushing and screening to produce a 95% passing 3.35 mm product, followed by heap leaching and gold recovery by the Merrill-Crowe process. The dore metal is refined at the Muruntau refinery. All gold produced by the joint venture is sold on the world market. IntroductionThe Muruntau mine and nearby town of Zarafshan are located in the center of the Kyzylkum desert, 250 miles west of Tashkent, capital of Uzbekistan. Following a mining conference in Moscow in 1990, a Newmont geologist was among the first team of westerners to visit the Muruntau Mine, the second largest gold producer in the former Soviet Union. At Muruntau, they found 220 million tonnes of low grade gold ore that had been stockpiled during the previous 25 years. In February, 1992, six months after Uzbekistan's independence, Newmont signed a 50/50 joint venture agreement with the Uzbek government to use heap leach technology to process the ore. The feasibility study was completed in November of 1992. Plant construction started in October, 1993 and operations commenced on May 25, 1995.Newmont Metallurgical Services performed metallurgical studies to obtain heap leach process design criteria parameters. The initial metallurgical study on 20 grab samples is the subject of this paper."

Jan 1, 1997

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By J. F. T. Agapito

Energy West Mining operates the Deer Creek and Cottonwood/Trail Mountain coal mines in the Wasatch Plateau about 40 km (25 miles) southwest of Price, UT. The Deer Creek Mine extracts the Upper Blind Canyon seam and the Cottonwood/Trail Mountain Mine extracts the Hiawatha seam 12 to 36 m (40 to 120 ft) below. Both seams average about 2.8 m (9 ft) in thickness. Cover depths exceed 550 m (1,800 ft) in a large portion of the unmined reserve. Stability problems at Deer Creek are mostly due to coal bursts caused by high stresses associated with deep cover and sandstone channels. Most of the bursts have occurred in gate pillars and, to a lesser extent, at the longwall face and during development. The introduction of a two-entry gateroad system with 9-m- (30-ft-) wide yield pillars has been a major factor in controlling and minimizing gate pillar [ ] bursts (Agapito et al., 1988). However, some bursting began to occur in the 9-m- (30-ft-) wide pillars as cover depths reached 550 to 610 m (1,800 to 2,000 ft). This was due to more rapid and higher abutment loading in areas with very strong roof and stiff floor.

Jan 1, 1997

By C. J. Parradies

During injection into a die, semi-solid metal alloys exhibit a shear-rate, history-dependent flow response. Simulating the injection of a thixotropic material requires that empirically determined boundary conditions and viscosity are specified as a function of both temperature and shear rate history. Experiments were performed using an industrial die casting machine that was instrumented with sensors to measure the pressure and temperature during the injection of a semi-solid aluminum alloy through a tube. This benchmark experiment was used to develop a simulation of the die casting process that could then be applied to more complex die geometries. The results of the experiments were analyzed using the exact, steady state solution for a power law fluid and simulations accounting for slipping at the boundary between the semi-solid metal and the die. Results indicated that the no-slip condition cannot be used to simulate the velocity boundary condition, because the measured pressure is much lower than that predicted by the models. An estimated apparent slip coefficient was introduced to account for the reduced pressure. During some of the experiments, a sudden drop in the measured pressured, prior to decreasing the ram velocity, coincided with observations of segregation in the form of concentric rings visible on the polished surface of cross-sections cut from material remaining in the tube.

Jan 1, 1997

By Jeffrey W. Fergus, Shiqiang Hui

"Aluminum is an important alloying addition to the zinc used in the hot-dip galvanization of sheet steel to control the properties and appearance of the resulting coating. Optimization of the galvanization process requires control of the alloy concentration which can be improved through the use of chemical sensors. Aluminum sensors based on molten electrolytes are commercially available but are not widely used because of their high cost. One approach to reducing the cost is to use a solid electrolyte which can simplify the sensor design and thus reduce the cost of fabrication. In this paper, the development of an aluminum sensor based on a solid fluoride electrolyte, specifically magnesium fluoride, will be described.IntroductionThe concentration of the zinc bath used in hot-dip galvanization affects the galvanization process as well as the properties of the resulting coating. Thus, accurate in situ measurement of the alloy composition can be used to improve process control. This paper describes a solid-electrolyte-based aluminum sensor for monitoring the bath composition during hot-dip galvanization."

Jan 1, 1997

Gold mineralisation at the Kerimenge-Lemenge prospects is a classical example of myltiple, overprinting events, associated with intrusive-related hydrothermal systems. Repeated emplacement of high level dacitic porphyry bodies (Edie Porphyry; 2.4 - 3.8 Ma) was accompanied by a phreatomagmatic eruption which formed a diatreme-maar complex. Later hydrothermal fluids utilised permeable fault zones and diatreme contacts. Mineralisation took place during two main events. Stage I consists of early quartz - illite/sericite - carbonate phase with associated pyrite-arsenopyrite mineralisation. This phase is zoned from quartz - sericite-pyrite/arsenopyrite in the south at depth, to dominantly manganocarbonate - illitic clay - arsenopyrite- pyrite_s significant base metals in the north and at shallow levels. The majority of known gold (18.1 Mt @ 2.0 g/t Au) at Kerimenge is associated with Stage I activity. The gold occurs primary within the lattice of the sulphides and is metallurgically refractory. Fluid inclusion studies indicate early boiling and progressive cooling and dilution of hydrothermal fluids during the evolution of the Stage I event. Near paleosurface condensation of gases, which evolved off the boiling system at depth, produced abundant low pH bicarbonate fluids. During the waning phases of Stage I activity, these bicarbonate condensate fluids descended down permeable structures and formed banded manganocarbonate veins. High grade non-refractory gold mineralisation during Stage II event is restricted to favourable structures at relatively shallow levels and in the northern regions of the prospect area. Gold in this event exhibits a distinctive Au - Ag - Te -Cu geochemical signature, and is associated with hessite - tennantite - chalcopyrite mineralisation within quartz veining. Alteration and fluid inclusion studies indicate that this style of mineralisation is a result of the quenching of pulses of hot, late magmatic mineralised fluids by the cold condensate waters.

Jan 1, 1997

By J. G. Pippenger

The Coteau Properties Company&apos;s Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. As part of the mining process, Coteau removes and replaces thin layers of suitable plant growth material (SPGM) generally ranging in thickness between one and five feet. Historically, tractor-scrapers completed this work; however, rising tractor-scraper costs and increasing haulage distances sent Coteau in search of a lower cost method resulting in the acquisition of a backhoe/truck fleet in 1995.

Jan 1, 1997

The major proportion of South African coal is extracted by the bord-and-pillar mining method which requires that the overlying strata be supported by pillars of coal. The stability of the pillars is a major safety concern. One of the factors which affects the strength of coal pillars is the intensity and nature of discontinuities in the coal seams. Current design methods for pillars assume that al the coal seams have equal strength and are equally disturbed by natural discontinuities, resulting in over-designed pillars in some cases and potentially unstable pillars in others. Research was carried out to determine the nature of discontinuities in coal seams and to assess their potential effect on pillar strength. It was found that large variations exist in the intensity of discontinuities in the different coal seams being mined. In addition, numerical model studies showed that the discontinuities could significantly reduce pillar strength if the width-to-height ratio of the pillars is small, but the effect decreases as the width-to-height ratio increases.

Jan 1, 1997

By K. G. Sutterer

The prevalent use of coal combustion byproducts in engineering applications has been with Class C and Class F fly ash as admixtures in structural concrete. But, the use of fly ash and bottom ash byproducts from modern desulfurization processes is receiving increased attention. The University of Kentucky has been conducting research into civil- and mining-engineering applications of these products. The studies have included extensive investigation of the geomechanical behavior of the materials and the effect of mineralogy on this behavior. These studies indicate important mineralogical considerations in the selection of materials for a specific application and highlight the importance of quality control before and during usage on specific projects.

Jan 1, 1997

By D. O. Murchu

Outokumpu Tara Mines located near Dublin, Ireland is Europe&apos;s largest producer of lead and zinc concentrates. To reduce dewatering costs and to improve environmental and working conditions, elimination of the lead concentrate thermal dryer was required. This paper describes the development and implementation of the pressure ceramic technology at Tara to replace a conventional vacuum filter/oil-fired dryer system. In 1996 the pressure ceramic filter dewatered 66,600tonnes of lead concentrate, producing a cake at 6 % moisture. Substantial operating cost savings have been realized. Commissioning of a second pressure ceramic filter to handle over 300,000 tonnes/year of zinc concentrates is scheduled for the first quarter of 1997.

Jan 1, 1997

By Aarao de Andrade Lima

Mechanical properties typical of coal are used in the comparisons of pillar strengths based on finite elements and the empirical equations of Holland-Gaddy, Salamon-Munro, Obert¬Duvall, and Bieniawski-PSU. A correlation among the strength parameters which are employed in the empirical equations, in Mohr-Coulomb and Hoek-Brown failure criteria is established. Emphasis is given to the important distinction between the mechanical properties of small rock specimens and those related to the rock mass. An elastoplastic version of Hoek-Brown criteria has been developed and implemented in a finite elements code. The strengths calculated using the empirical equations showed a good agreement when the ratio width by height of the pillars varied from I to 8, except for Holland-Gaddy equation which exhibited lower values. Under the hypothesis of associative perfect elastoplasticity used, pillar strength calculated using Mohr¬Coulomb yield criterion became excessively high for all the models having a pillar width by height ratio above 2. The finite elements solution based on Hoek-Brown criterion predicted strengths around fifty percent larger than Bieniawski-PSU equation when the pillars width by height ration varied from 3 to 8, showing good agreement below that range. It has been concluded that, under the hypothesis of percfect plasticity, stress analysis techniques may overestimate the strength of rock structures subjected to high confining stresses.

Jan 1, 1997

Sphalerite is commonly floated in an alkaline environment and under such conditions the overall activation mechanism is obscured by the hydrolysis of Cu2+ and precipitation of Cu(OH)2. Electrokinetic and kinetic flotation tests show that the activation of sphalerite is a two-stage process; the activation products formed on the surface of sphalerite in near neutral and in alkaline solutions in the first rapid activation stage are "flotation-inactive". These layers, when formed in an alkaline solution, are unstable and are transformed into the "flotation-active" form in the second stage. However, the surface layers formed during activation in alkaline environment by copper in the presence of lead ions are very stable and even after a long conditioning time the flotation rate is not improved. Consequently, while both Cu2+ and Pb2+ activate sphalerite flotation, quite unpredictable effects may result when both are present in the solution.

Jan 1, 1997

By R. Robertson

Dense medium cyclones are the preferred means for cleaning 112 in. x 14 Mesh to 28 Mesh (12.7 mm x 1.0 mm to 0.6 mm) raw coal and are becoming a common choice for cleaning raw coal from a nominal top size of 2-1/2 in. to 3 in. (63.5 mm to 76.2 mm) down to 14 Mesh to 28 Mesh (1.0 mm to 0.6 mm). During the last ten years, dense medium cyclone circuitry design has undergone changes which have combined to improve process efficiency. This paper describes these improvements and compares present day design with the design used prior to the mid 1980&apos;s. Improvements in the following areas are described: Raw coal desliming, cyclone configuration, drain and rinse applications, dilute medium circuitry, and instrumentation and control.

Jan 1, 1997

By Roy H. Grau

The trend in underground room-and-pillar cod mining is to employ remote-control continuous mining machines to take extended cuts of 40 A or more. Roof fall safety hazards to the mine worker associated with 4ed cutting are not completely de6ned but are known to include removal of the miner operator from the protective canopy, non-compliance with approved cutting depth and CM operator positioning. This report summarizes ground control research performed by the National Institute for Occupational Safety and Health (?-JIOSH) researchers at the Pittsburgh Research Laboratory concerning extended cuts. A combination of statistical analysis and underground investigations have been conducted. Statistical analysis of extended cut use, along with roof fall accidents and fatalities data delineate the extent of the problem in U.S. coal mines. Additionally, an underground study is described where the long-term roof stability of extended cut areas are compared to standard cuts.

Jan 1, 1997

By LaBrooy SR

A number of gold processing plants in Western Australia have nickel in their ores, leading to significant levels of nickel on their loaded carbon. The presence of nickel during leaching, adsorption and elution&apos;may have detrimental effects on cyanide consumption, carbon inventory requirements, stripping costs, electrowinning efficiencies and may contaminate the gold bullion.This paper discusses the competitive adsorption of gold and nickel cyanides onto activated carbon and investigates changes in solution parameters that may improve gold adsorption and/or inhibit nickel adsorotion.

Jan 1, 1997

The resources industry is unique in that the finite nature of resource deposits requires a participant to be constantly locating and developing new ones to replace those that are depleted. An effective growth strategy that enables new project developments to be brought on line in time and within budget is therefore of fundamental importance to any mineral resources company. This paper seeks to identify the role of the development project in the company&apos;s overall growth strategy and the key performance criteria that a development project must achieve in order to allow a company to meet its growth objectives.

Jan 1, 1997

By Bob J. MacDonald

The Cape Breton Development Corporation is a federally owned Crown corporation in Canada that operates two coal mines the Prince and Phalen Colliery in the Province of Nova Scotia. Retreat longwall mining was first introduced to the shallower workings (I 80m) of Prince Colliery in the early 1980&apos;s. Phalen Colliery started longwall retreating in 1987 and since that time has extracted twelve panels. In 1993 there had been a total of eight longwalls varying in widths from 140-230m mined in Phalen Colliery that is on the Phalen Seam. Up to this point there were only minor ground control problems on the faces except for one of the earlier longwalls that was mining a split seam. There is some interaction on Phalen workings from remnant structures in the overlying Lingan and No. 26 Collieries which worked the Harbour Seam. Induced abutments loads along pillar edges have been observed and resulted in poor face conditions when mining the Phalen Seam. The ninth panel, 6 East was the first panel to suffer a major roof fall from the First Major Weighting. This was also the first panel to undermine a paleo sandstone river channel named the Lower Sandstone Unit (LSU). For the first time in Phalen&apos;s history subsequent longwalls began to experience periodic weighting events. The 6 East panel suffered a number of periodic weightings and on two occasions had to use foam cement to fill the cavities that resulted. On the next east side panel, 7 East, there were numerous periodic weighting events, but interestingly there was no significant First Major Weighting. 7 East was the first 260m wide panel and all others were 230m or less. This longwall was 3,400m long and began producing in December of 1994 and was still cutting coal in May of 1997. There were five significant roof fall events on this panel, three of which required foam cement to fill the cavities. Of these three the interruption to production varied from four days to seven months. There were definite precursors to each of the weightings including: 1) an increase in audible noise (termed bumping) on the face, 2) supports went rapidly into yield, 3) roof convergence increased, 4) water percolated from the face roof strata, and 5) severe spalling of the coal occurred resulting in increased tip to face distance. Longwall face weightings are a result of geomechanical factors and cannot be avoided However, the loss of roof control is a different matter and highly subjective to operational procedures. The causes of weightings, their magnitude and impact on the mining at Phalen have been investigated. The following factors have been identified as relevant to these occurrences. 1. The influence of pillars in the overlying Harbour Seam workings. 2. Location of the LSU relative to the Phalen Seam. 3. Thickness of the LSU. 4. Pressure arch effect from the adjacent gobs. 5. Poor operational practices on the longwall including: a) slow rate of retreat; b) inadequate supply of pump pressure to the hydraulic supports; c) premature yielding of the yield valves; and d) poor face alignment practices. This paper will review the events that took place on the 7 East longwall and show that the Lower Sandstone Unit is the primary cause of the weightings. However, other factors contributed to the loss of roof control and the formation of the roof cavities.

Jan 1, 1997

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997

By Jeffrey J. Schwoebel, Jianliang Li, Daniel J. Brunner

A United Nations (UN) administered degasification technology transfer project, funded by the Global Environmental Fund (GEF) is underway at the Shihao Mine of the Songzao Coal Mining Ad- ministration in the province of Sichuan, Peoples Republic of China. This mine exploits multiple seams at depths ranging from 300 to 600 m below surface. In-seam boreholes and frequently spaced in-mine vertical boreholes, developed from underlying galleries constructed specifically for this purpose, currently degasify the seams in advance of mining at the Shihao Mine. Because of ventilation system constraints and the in-situ gas con- tent, longwall mining of the coals at this mine could not proceed without some form of pre-mining degasification. This paper presents a simulation based degasification plan of long, in-seam horizontal boreholes for the Shihao Mine. Simulations with a coalbed reservoir program assessed time dependent degasification characteristics of both vertical and in-seam horizontal boreholes. The simulations used input data from reservoir and desorption tests conducted at the mine site. The results produced system design nomograms to assist mine engineers in defining the appropriate borehole spacing necessary to degasify the seam in the time available for pre-mining drainage. The predicted effectiveness of the current vertical degasification scheme was compared with that for a horizontal borehole program and served as the basis for the recommended in-seam borehole configuration for the project at the Shihao Mine. The horizontal borehole degasification program requires substantially less gallery and borehole development than the present vertical degasification scheme.

Jan 1, 1997