Search Documents

The growth of the mining industry around Australia over the last ten years has seen many open cut mines developed on shallow oxide reserves. Most of these have been gold operations, although there are some copper mines in the list, too. Many of these have exhausted their oxide reserves and have made the transition to underground mining to access their deeper sulphide ores. Other operations have reached or are approaching the point where the decision has to be made to go underground or cease mining. This paper discusses the issues involved in making the transition from surface to underground mining. The aim is not to discuss each of the issues exhaustively. This would take a conference in its own right. Nor is it intended to provide a primer on underground mining. Instead the aim is, firstly, to flag the issues which must be addressed when planning to make the transition from surface to underground mining and, secondly, to identify critical aspects of mine development.

Jan 1, 1997

By R. Padilla

A thermogravimetric study has been conducted to follow the decomposition and volatilization of arsenic from enargite concentrate in nitrogen and slightly oxidizing atmospheres. Temperature has a large effect on the rate of volatilization of arsenic. Fractional volatilization of arsenic as high as 98% were obtained in less than 60 min at 650°C in nitrogen atmosphere, while in slightly oxidizing atmosphere the same volatilization could be achieved in 30 min. It was found that arsenic volatilizes as sulfide in nitrogen atmosphere and as 4xture of sulfide and oxide in atmospheres containing 1% oxygen. By using the pore blocking and the first order kinetic models, apparent activation energies of 213 and 200 kJ/mol for the temperature range of 780 - 900 K and 205 and 184 kJ/mol for the temperature range of 900 - 985 K were determined for enargite and copper concentrate, respectively.

Jan 1, 1997

By Kuda R. Mutama, Allen E. Hall

A wind tunnel investigation into the fundamental characteristics of jet fan performance is described. The effects of varying fan positioning in a square tunnel cross section are reported for two fan outlet diameters and velocities. Tests were conducted, also for a jet fan placed in a flow developed by an external fan operating in the same direction as the jet fan. The position of the jet fan relative to the tunnel walls was found to affect its performance. Performance parameters were determined and used to formulate theoretical equations based on momentum and energy considerations. The results identified a range of flow ratios which can be used to design an effective jet fan ventilation system and provide a basis for the selection of jet fans for practical mining applications

Jan 1, 1997

By Bok-youn Kim

Presently, mobile diesel equipments contributes a lot in improving the economical feasibility of underground mining and tunneling operations. Even in Korea, quite a large number of diesel equipments is being applied to the underground workings already. This paper introduced the production procedure, characteristics and evaluation technology on diesel particulate matter(DPM) that is known as a carcinogen For easy measurement of DPM using laser dust monitor, the conversion factor(K) to gravimetric concentration was acquired. The field measurement of DPM was conducted to make a comparison between locally manufactured on-road equipments and imported equipments specially designed for underground use. According to the Government regulation revised h 1996, it was learned that the critical pollutants among the diesel exhaust is DPM instead of NOx which have been considered as a critical pollutants.

Jan 1, 1997

By Samantha Beeson, Collin Poole

"This paper examines the development of two new selective flocculation techniques for recovering KCI values from low grade carnallite potash ore.Direct recovery of KCI was achieved using one of two mid-range molecular weight polymers, one non-ionic and the other strongly cationic, in conjunction with the same selective anionic dispersant. From initial response studies on pure minerals and selective flocculation tests on synthetic mixtures, investigations were extended to recover KCI values from a natural carnallite potash ore. A single-stage process achieved products grading up to 61.3% KCI at recoveries up to 85.4% for the cationic flocculant suite and up to 64.8% KCI with recoveries as high as 90.3% for the non-ionic flocculant suite, with dispersant and flocculant dosages of 150-250gr1 and 10-75gr1, respectively. These results clearly demonstrate not only the feasibility of treating such problematic ores at low reagent dosages, but also the potential elimination of desliming prior to froth flotation.The experimental results presented are considered in terms of the reagent adsorption phenomena present in the system and various aspects of floe formation and cleaning.IntroductionAs high-grade sylvinite potash ores become scarce, lower grade sylvinite and carnallite potash ores are becoming more attractive. However, these ores often contain large amounts (up to 15% by weight) of water-insoluble slimes which must be removed prior to KC! flotation, owing to their high adsorptive capacity for the amine collectors used. The slimes are generally removed by scrubbing followed by hydroclassification and any residual material not eliminated is blinded with reagents such as guar gum or starch to inhibit interference in subsequent KC1 flotation.An alternative approach used commercially in Canada by Agrium Inc. involves water-insoluble slimes flotation prior to KC! flotation. In this process, the slimes are selectively flocculated and then separated by froth flotation. Losses of KC! to the slimes product and associated brine requirements are both reported to be less than those encountered in conventional desliming, but the technique is somewhat limited in its application at present."

Jan 1, 1997

By J. Wiebmer

The two most important influencers of cost-per-ton in an underground mining machine are its productivity (tons/hour) and its availability-utilization (hours/year). Operating cost and initial price have far less impact. This paper reviews a cost-per-ton sensitivity analysis for underground mining equipment and discusses benchmarks for measuring its performance. The conclusion is that miner-supplier partnerships and the Information Age are the two most significant trends in cost-per-ton reduction.

Jan 1, 1997

By C. T. Twort

As technology and economic conditions allow mines to operate at ever greater depths, increasing demands are placed on the environmental engineer to adjust the capacity of the installed mine . - refrigeration systems. At the same time the engineer must satisfy the changing legislation, which demands that developments are carried out in as an energy efficient and environmentally accept- able manner. Following the trends outlined above, this paper is written to give an overview of the current and potential future refrigeration technology available to the mining industry. The effects that may be produced by the adoption in mining applications of the new generation of 'green' refrigerants are examined both at the design stage and when considering the viability of retrofitting existing systems so that they comply with the Montreal Protocol. An introduction to the concept of Total Energy Warming Impact (TEWI) is provided, with an explanation of its use in optimising system design and performance, and its incorporation as part of an environmental audit strategy. The paper concludes with a discussion of innovative refrigeration techniques and the possible future developments in legislation.

Jan 1, 1997

By J. A. L. Napier

This paper presents an overview of work carried out by the CSIR Division of Mining Technology and formerly by the Chamber of Mines Research Organization (COMRO) to quantify the behaviour of the stope fracture zone near deep level goldmine stopes. The motivation for this work is first reviewed in the context of the unsatisfactory status of current mine layout design criteria. Numerical methods to represent failure processes are reviewed briefly. Specific studies of microfracture processes are described as well as physical modelling experiments that can yield insights into deformation mechanisms. Modelling of stope scale deformation mechanisms are presented and considerations relating to elastodynamic modelling of the rock mass are described. The implications of this understanding in relation to prospects for active fracture zone ?engineering? are outlined and finally, the directions of future research work are proposed.

Jan 1, 1997

The Filblast Cyanidation Process incorporating intense high shear mixing, high gas mass transfer efficiency and high oxygen concentrations under conditions of elevated pressure has now been been successfully applied in gold cyanidation mills since May 1993. The first commercial unit had a slurry capacity of 110 cubic metres per hour. Since then 230 and 450 cubic metre per hour units have been installed and a 1000 cubic metre per hour unit has been designed. Laboratory and pilot plant Filblasts have also been built.The reactor is a robust, compact in-line or end-of-line device and may be constructed out of a wide range of materials including wear and corrosion resistant alloys and ceramics. The Filblast Process may be applied to high temperature leaching of refractory gold ores and base metal concentrates.

Jan 1, 1997

By J. M. Kruger

High-resolution ground-penetrating radar (GPR) was used to image the near-surface extent of two exposed Late Cretaceous kimberlites intruded into lower Permian limestone and dolomite host rocks in northeast Kansas. Six parallel GPR profiles identify the margin of the Randolph 1 kimberlite by the up-bending and termination of limestone reflectors. Five radially-intersecting GPR profiles identify the elliptical margin of the Randolph 2 kimberlite by the termination of dolomite reflectors near or below the kimberlite's mushroom-shaped cap. These results suggest GPR may augment magnetic methods for the delineation of kimberlites or other forceful intrusions in a layered host rock where thick, conductive soil or shale is not present at the surface.

Jan 1, 1997

By J. C. Stankus, S. Guo, S. S. Peng

In this paper, a model is developed for a resin anchor bolt system in which the smooth bar is modeled by using one-dimensional truss elements, and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined and then incorporated into an existing computer code called Roofbolt. After this development, all of the components in the resin anchor bolt system, including smooth bar, bearing plate and resin annulus, can be correctly modeled.

Jan 1, 1997

By W. Blake, J. K. Whyatt, B. G. White

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations in in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence collected from the Lucky Friday mine by US Bureau of Mines researchers, as well as a review of previous case studies, demonstrated that in situ stress variations affect the [spatial] distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies. they are too expensive and, depending, on conditions, may be too difficult to collect. However, information on borehole and raise breakouts: deformation of mine openings: and patterns of seismicity, ground-control problems and rock-burst damage can be used to build a stress database. In conjunction with maps of mine structure and geology and models of rockmass behavior, this database can then be used to build a map of in situ stress variations. Such a map could provide a means of anticipating patterns of mining-induced seismicity and. Thus, could be the basis for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1997

By A. H. Summers

The La Choya mine is located 55 km south of Sonoyta in northwestern Sonora, Mexico. Mineralization is controlled by a 40 meter thick thrust fault zone which created a permeable host for the metal-bearing hydrothermal solutions. The ore body is mined by open pit using wheel loaders and truck haulage. Gold and silver are recovered from low grade ore by heap leaching followed by carbon adsorption.

Jan 1, 1997

By Hunter TC

Metals Refining Operations Pty. Ltd. (NMO), PNG's only gold and silver refinery is operated by Golden West Refining Corporation Ltd (GWR), a member of the Rothschilds group and has a strong PNG ownership link through statutory shareholders. Located in Waigani, MRO has been successful in substantially increasing production through toll refining for Porgera, Misima, Tolukuma, Wapolu and, more recently, at Lihir as well as treatment of alluvial gold from smaller operations. This increased throughput has resulted in the need to constantly upgrade equipment, techniques and practices, particularly to continue quality improvements and meet market demands. The evolution of these changes are documented and discussed and the probable future development plans are detailed.

Jan 1, 1997

The Beaconsfield Gold Mine within the township of Beaconsfield in northern Tasmania has been established in recent years to exploit a known resource in the Tasmania Reef which was mined to a depth of 450 m below surface between 1877 and 1914 yielding 850 000 ounces of gold. Activity at Beaconsfield over the past 30 years has involved drilling to assess the resource and rehabilitation of the top 100 m of the Hart Shaft that had collapsed since the original closure. More recently the mine has been dewatered to the 375 m Level and work is well advanced establishing infrastructure aimed at recommencing production during 1998 - 99. This paper reviews geotechnical studies undertaken to-date and provides a brief overview of some practical methods of analysing ground conditions. It pursues simple observation and analysis as a tool for assessing mine design and ground support options without recourse to extensive monitoring and measurement and avoids the use of elaborate models before the basics are understood.

Jan 1, 1997

By K. Kim, T. M. Yegulalp

A numerical model is being developed to assess the enhancement of ore permeability by improving fracture connectivity with micro-hydrofracturing. As part of this project, a generic two-dimensional percolation model was developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park mine was used to establish the statistical properties of the observed fracture systems. Results of statistical analyses of field data and examples of the use of the percolation model are presented

Jan 1, 1997

By A. G. Jackson, S. J. P. Laube

"Control of thin films during the growth process is dependent on several parameters that are difficult to monitor, including flux of film material, pressure, substrate temperature, composition, and thickness. One means for easing this difficulty is to take advantage of emission spectra associated with the process and the film. For pulsed laser deposition (PLD), the ion cloud generated by the laser has characteristic emission spectra that can be used to control the flux and, hence, the film. For chemical vapor deposition, the species present can be determined using mass spectroscopy and specific peaks can be used to control the deposition. Raman spectroscopy affords the possibility of real-time control by sensing characteristic peaks associated with film composition and thickness. These spectroscopic methods offer a real-time alternative to process control that is very attractive, because of the ability to accurately control films to achieve the engineered structures and properties sought. Examples are presented to illustrate the capabilities of these methods for thin film preparation.IntroductionThe drive to reduce costs and improve efficiencies of operation sets the tone for much of research, basic or applied. Basic research is limited by the ability of sensors and associated instrumentation to measure parameters accurately and reproducibly. Applied research has the same limitations and also the added constraints of time and costs. Hence, there are strong incentives to explore means for refining existing sensors with respect to performance and cost, as well as finding new sensors and techniques for more accurately and rapidly measuring quantities of interest in experiments and in various processes."

Jan 1, 1997

By John Rushton

Surface mining, from ore extraction to processing, requires many types of equipment to obtain the final product. Mine equipment often includes shovels, drills and haul trucks. Ore processing equipment, including plants, mills and concentrators, are also part of surface mining operations. Surface mining operations emphasize production. Production is where the bills are paid and fortunes are made. However, there must be support to keep the equipment operational. To most production people, equipment maintenance is a necessary evil. Maintenance is not glamorous work. It is often neglected when praise is being passed around. It is easy to recognize higher production, greater capacities, faster cycle times or more loads hauled. But who cares if an engine is replaced in 12 hours instead of 48? The answer is, everyone should - from the hourly miner to the mine manager. Surface mining equipment needs constant maintenance work. It must be lubricated, components replaced, electrical problems repaired and other problems addressed. Repair work for any surface equipment takes time away from production. It costs money. Maintenance costs cannot be avoided. However, they can be minimized. Minewide communication should include operations cooperating with maintenance. Traditionally, operations resist surrendering equipment to maintenance if it can continue to produce. The rationale is, every load that can be hauled today is money in the bank. If the unit is taken down, the money is lost. This thinking is prevalent in many surface mining areas, including the mill. "Not on my shift," the operator thinks. "Let the next crew worry about it. The problem with this thinking is in probability and statistics. The longer equipment goes without maintenance work, the higher the probability of equipment failure. When the failure does occur, it is certain to cause the equipment to remain down longer than if the maintenance department had been allowed to take it down. Many mining operations have closed early in their lives because of poor maintenance practices. This has become the industry standard because substandard levels of performance are acceptable. Management believes it gets five to six hours of work from maintenance people during an eight-hour shift. Actually, the industry average is less than two hours of work per shift. Real productivity levels of less than one hour are not unusual. There are few exceptions. However, a daily work schedule (DWS) will increase productivity at many properties by 50% to 100%. A 200% improvement is not unusual. The DWS will work. Maintenance people are among the most intelligent and motivated people on the property. They deserve the chance to be productive. [ ] In preparing a DWS, management needs to understand two productivity principles - the productivity spread and the real maintenance workday.

Jan 1, 1997

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By Joseph C. Rota

The Carlin Trend is one of the most significant gold mining districts in North America. Located in northeastern Nevada, a total of over 17 million ounces of gold have been produced since 1965 at Newmont Gold Company's open-pit and underground operations. Oxidized portions of the sediment-hosted, disseminated gold deposits at Carlin generally consist of finely disseminated concentrations of sub-micron sized native gold particles hosted in Paleozoic siliciclastic or carbonate rock. Oxide ore is commonly amenable to dump leach or heap leach processing, yielding an average 50 to 70% recovery of total contained gold. Refractory unoxidized ore requires some form of pretreatment oxidation to ensure economic gold recovery. Geologic ore control is typically combined with standard assay and engineering techniques to maintain both grade and metallurgical control ofleach grade ores. Mine geologists provide a vital function through field observation and recording ofmineralogic data during daily, visual blasthole logging. Intricately mixed refractory materials must be separated from oxide ore to ensure highest possible gold recoveries. Geologic information is combined with assay data to create mine polygons in an engineering computer database. Mining selectivity is further enhanced by in-pit ore control geologists who are available to make production decisions based on direct mineralogic observations at active mine faces.

Jan 1, 1997