Search Documents

By Phillip B. Bucky, Fred D. Wright

The present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should Prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems, The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.' As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining Cost. It Was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1949

By John W. Vanderwilt

The unpredictable behavior of ground movement and subsidence has complicated the problems that attend the extraction of large quantities of ore. Special studies, particularly relating to coal mining, have yielded such a voluminous literature and so many involved controversial theories that a partial review would be difficult. Limited space makes any kind of a review impractical. The features to be considered cover only a relatively small part of the broad problems of ground movement and subsidence, but it is believed that this small part is critical. The practical aspects are important, since they bear directly on safety of mine workings, on recovery of ore and on dilution of ore in block caving and related systems for extracting large quantities of rock. The ground movement to be described occurs outside the vertical boundaries of a caved block in the area that is commonly referred to as being in the "zone of draw." "Draw" is a term that originated in the subsidence problems related to coal mining, and it is defined by a line drawn from the margin of the area caved underground to the most distant fracture at surface on the same side of the caved area as shown in Fig. I.' A line thus drawn is called the cave line, and its angle with respect to the horizontal is the cave angle or angle of draw. It is understood that the line is taken normal to the limit of mining, and in a vertical plane. The prevailing theories as to draw and angle of draw assume that appreciable movement occurred along the cave line, which has been described as a fracture resulting from the shearing action brought about by the weight of the overlying load. Fig. 3 shows diagrammatically the mechanics of ground movement adjacent to an area of subsidence according to the prevailing theory of draw (A, from Royce2) and, for comparison, ground movement observed in the Climax mine (B). The text in Peele's Handbook2 referring to Fig. 2 does not state the meaning of the "original position of top of workable ore" in the rectangular space above "ore in place," and the arrows are not explained. However, this presentation is most concerned with the zones outside the rectangle. According to the prevailing theory, as shown at the extreme left under A, Fig. 2, the vertical tension cracks at surface change at a shallow depth to shear fractures forming the cave line, and it is assumed that appreciable movement takes place along the cave line toward and into the subsiding caved block. The mechanics of ground movement observed in the Climax mine, as shown under B, Fig. 2, does not accord with the prevailing theory, particularly as regards the cave angle and draw. The vertical tension cracks seen at surface die out at depths of 150 to 225 ft. and shear fractures do not develop. Movement is confined at surface to a mantle of rock 50 to roo ft.

Jan 1, 1949

By J. W. Galpin, V. L. Minear, W. D. Owsley, F. C. Sturges, B. H. Mott, R. H. Allen, W. W. Weigel, R. E. Moeller

By definition the word "grout" means a thin mortar, or a kind of plaster or cement, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1949

By R. M. Franz

This paper considers potential risks to the health of workers in ultra-deep mines, including barotrauma, physiological effects and toxicity of airborne pollutants. Relevant previous research is reviewed, including work by the Chamber of Mines Research Organization and the Deep Mine Cooperative Research Programme, and recommendations are offered for prospectively limiting pressure-related health risks.

Jan 1, 2005

By S. A. Lolon, J. F. Brune

"INTRODUCTION In underground longwall coal mining, the mined-out areas or gobs frequently contain methane which can form explosive methane-air mixtures. Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of such explosive mixtures, herein referred to as Explosive Gas Zones (EGZs), inside and around the perimeter of bleeder-ventilated longwall gobs (Loane et al., 1975; Lynn et al., 1986; Elkins, et al., 2001; McKinney et al., 2001; Dziurzynski and Wasilewski, 2012; Brune, 2013). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Several factors can induce EGZs outflowing from the gob, but the most common cause is the fluctuating barometric pressure. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Other sudden pressure changes can result from roof falls, failing ventilation controls and fan outages. Any such fluctuation of mine ventilation pressure will disturb the pressure differential between the gob and the surrounding mine workings and may cause EGZs to outgas from the gob. The correlation between major mine explosions and abrupt barometric pressure changes has been studied and confirmed for explosions in coal mining countries including the United States, South Africa, Australia, and Poland (Hosler, 1948; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Hemp, 1994; Wasilewski, 2014; Belle, 2014; and Lolon, 2017). Disastrous mine explosions appear to happen more frequently during stormy weather, which, in the United States, typically occurs during the late fall and winter seasons. ROOT CAUSE AND EFFECT OF GOB BREATHING Gob breathing is the result of the pressure differential between gob internal and external pressures caused by external atmospheric pressure fluctuations that occur naturally as a result of gravitational and thermal forces in the atmosphere (Lindzen and Chapman, 1969). Other major and sudden pressure changes may be caused by fan failures, failures of ventilation controls or roof falls can also cause an unexpected gob breathing. Normal barometric fluctuations occur every day but usually do not pose an explosion risk as they occur gradually so gob pressures have sufficient time to equilibrate. More extreme fluctuations associated with cyclonic weather systems and storms often result in more rapid and larger drops or rises in barometric pressure (Hosler, 1948; Fauconnier, 1992). A study by Lolon (2017) found that the timing of historical mine explosions showed consistency with the occurrence of abrupt and intense barometric variations."

Jan 1, 2018

By Jorge Madias

Se analizan las distintas alternativas para la producción de barras de refuerzo de hormigón: endurecimiento por solución sólida (“dureza natural”); endurecimiento por temple y autorevenido en línea (Tempcore, Thermex, etc.) y endurecimiento por precipitación (microaleación con niobio, vanadio o titanio) y su influencia sobre la performance de las barras, en lo que hace a la resistencia a la corrosión, al fuego y a los sismos.

Aug 17, 2017

By Max Moya Bendezú

"El presente texto analiza algunos problemas inherentes a la fabricación de barrenos integrales, así como presenta una posible solución a los mismos. Los barrenos de perforación con collarines de jebe no han dado buenos resultados en Morococha. Sin embargo, su implantación en otras áreas de las minas de la compañía, como perforación podrá representar ahorros considerables en este renglón del costo total de producción. La principal causa de falla de los collarines de jebe es el recalentamiento que estos sufren por impacto y vibración al punto que descompone el jebe causando su prematuro deslizamiento. En ese sentido, los collarines de jebe solo son exitososcuando son usados con máquinas más ligeras que las empleadas en el presente experimento o cuando las presiones de aire no sean mayores de 65 o 70 libras por pulgada cuadrada. "

Sep 1, 1968

By Tim O’Neil

Big and getting bigger. Barrick Gold Corp., the third-largest gold producer in the world, began production in September — ahead of schedule — at its Meikle Mine. At a scheduled full production rate of 12.4 t/a (400,000oz/year), it will be the largest producing underground gold mine in the United States. The $180-million Meikle Mine is located on Barrick’s Goldstrike property in Nevada and has 205 t(6.6 million oz) of gold reserves. The compact Meikle deposit has an average ore grade of 23 g/t (0.68 oz/st), making it one of the highest-grade mines in the country.

Jan 1, 1996

This paper reviews the various processes successfully in operation to treat refractory gold ores and describes in detail the alkaline pressure oxidation circuit operating at the Barrick Mercur Mine, Utah, U.S.A., on car- bonaceous/sulphide refractory ore and the acidic pressure oxidation circuit operating at the Barrick Goldstrike Mine, near Carlin, Nevada, U.S.A., on sulphide refractory ore. The autoclave process is important to Barrick for the extraction of gold. The Company has operated successfully a 750 ton per day unit at its Mercur property for the past two years and more recently has commissioned a 1500 ton per day unit at Goldstrike. The paper presents data relative to operating costs, materials of construc- tion for autoclaves and peripheral equipment, reagent requirements, and changes required during commissioning for both autoclave systems.

Jan 1, 1991

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

By S. Haggarty, R. Walton

Barrick's growth and development plan will add three major new mines during 2005 including the Lagunas Norte Project in the La Libertad Province of Peru, the Veladero Project in the San Juan province of Argentina, and the Tulawaka Mine in north¬western Tanzania. Lagunas Norte and Veladero are similar in that they are both green-field open pit deposits at elevations over 4,000 meters above sea level, with two stage crushing and heap leaching followed by Merrill Crowe zinc precipitation for precious metal recovery. Operating sites will each generate in excess of 700,000 ozs Au per annum with commissioning and full scale operation planned during the third and fourth quarter of 2005. Details with regards to regional geography, development schedule, production and process specifics for Lagunas Norte and Veladero will be discussed in this presentation providing an overview for the respective properties.

Jan 1, 2005

By Steve Custer, Tim Kahl, Sue Parker

"The primary objective of the Barrick Goldstrike expert system is to achieve the desired liberation size for the autoclave circuit while maximizing throughput. In addition, when downstream limitations (autoclave circuit or others) restrict the milling circuit tonnage the expert system further improves grinding product size. Since its implementation, the expert system has provided expected throughput improvements while improving or maintaining circuit performance.Barrick Goldstrike and MinnovEX Technologies Inc. teamed up to install an expert system to control Line I and I1 of the autoclave grinding circuits. The dissimilar equipments of the two grinding circuits coupled to different production objectives, skepticism among operators, and the variability of the ore types processed in each line challenged the implementation.To ensure implementation success, Barrick Goldstrike dedicated four administrators full time to the project. The system administrators included two metallurgists, a process control engineer and a mill trainer. As usual, the control room operators were the experts who provided the operational logic for the foundation of the control system. The administrators and all eleven of the control room operators signed off on acceptance of the system. Current online utilization is 95%.INTRODUCTIONThe grinding circuit for Barrick Goldstrike’s autoclave process consists of two SAG Mill Ball Mill lines. Line 1 grinding circuit is comprised of a 22 by 8 foot, 2500 horsepower Allis Chalmers (AC) variable speed SAG mill, followed by a 12.5 by 14 foot, 1250 horsepower AC ball mill, and a 13.5 by 18 foot, 1800 horsepower Dominion ball mill in parallel. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1352 Nordberg Omnicone crusher (4.5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The ball mill circuit is closed with 6 Krebs super D20 cyclones. Line 2 grinding circuit is comprised of a 24 by 12 foot 4000 horsepower Fuller variable speed SAG mill followed by a 16.5 by 30.5 foot 5000 horsepower Fuller ball mill. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1560 Nordberg Omnicone crusher (5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The line 2 ball mill circuit is closed with 12 Krebs super D20 cyclones. The underground Meikle ore is typically fed through Line 1. Achieving the desired product size is critical for successful processing of Meikle ore. Open pit Betze ore is fed to Line 1 when Meikle ore is unavailable. Line 2 processes Betze ore exclusively. Throughput is maximized when processing Betze ore as the product size is less critical. The products of these two circuits are combined as feed to the autoclave circuit. The ore types and the autoclave circuit demands determine the required grinding circuit product size and maximum combined mill feed tonnage."

Jan 1, 2001

By Andy Cole, Ken Thomas, Stephen Durn, Jacques McMullen

"The roasting and gas handling circuits of the Barrick Gold’s new Roasting Facility at the Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Product from the up-stream dry grinding circuit requires roasting to maximize gold recovery. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type “double refractory” ores. Double refractory is indicative of the gold being difficult to direct leach due to a combination of pyrite encapsulation and the carbonaceous preg-robbing of the ore.A very extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NO, reduction before venting to the atmosphere.The roasted calcine is quenched, neutralized and then thickened before leaching in the carbon-in-leach-circuit.INTRODUCTIONBarrick’s strategic development plan integrated the production of gold from Goldstrike’s carbonaceous ore reserves by 2000. A due diligence review of carbonaceous ore processing options was initiated during the second half of 1 996. Processes considered included autoclaving followed by a proprietary ammonium thiosulfate leaching process, fine grinding/autoclaving as practiced then by Santa Fe, and whole ore roasting as practiced by then Independence Mining and Newmont. The objective by year-end was to recommend the most robust and economical process for Goldstrike’s carbonaceous resources. In the fall of 1996, a detailed review of roasting as a processing alternative for Goldstrike was initiated."

Jan 1, 2001

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By Ray Walton, Ron Colquhoun, Ken Thomas, Dwayne Fentie, Barney Burke

"The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources.The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3% year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.BACKGROUNDAs early as 1992, Barrick’s Goldstrike Mine, located north of Carlin, Nevada had indications of the ore becoming ever increasingly carbonaceous in nature. As the open pit and underground exploration programs proceeded to step out over the years that followed, the accumulative amount of carbonaceous refractory ore and tons had become significant. By 1997, 29 million tons of double refractory carbonaceous ore containing an estimated 11.6 million ounces of gold had been identified. By 2000 the resource had increased to 14.3 million ounces."

Jan 1, 2001

By A. Cole, A. Bolland

The roasting and gas handling circuits at Goldstrikes' new Roasting Facility incorporate proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available unit operations from the perspective of capital, environment and operating costs. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type carbonaceous ores. An extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NOX reduction.

Jan 1, 2001

By Julio E. Claudeville

Approaches and Lessons Learned ??Address business needs?local skills training and employment ?local procurement programs ?health and safety programs ??Ensure consultants/ advisors/ contractors apply Company standards ?especially in the field/ locally ?will not be differentiated from the Company itself

May 1, 2006

By J. Ran

Ground instability is among the major causes of serious incidents and production disruptions in the mining industry and has a significant impact on safety. Mining companies may have operations in a number of jurisdictions with varied regulatory requirements for ground control management. As these companies expand into countries where mining regulations are formative or lacking clear definition, ground control practices are usually developed by local mine personnel based on their experience. In many cases, inconsistent procedures and standards are generated, which can lead to an increase in occurrence of underground incidents due to difficulties and confusion in implementation. This situation has forced some mining companies to standardize their ground control practices by geographic regions or divisions. Though this approach is an improvement, it may not lead to effective management of ground control issues across all operations of a global mining company. Barrick Gold Corporation, with operations in North and South America, Australia and Africa, decided to adopt a global approach to ground control management. This global approach requires all Barrick operations to prepare and implement an effective ground control management plan (GCMP) based on site specific conditions and company guidelines. It is also required that the GCMP be developed through application of sound geotechnical engineering practices and be consistent with local regulatory requirements and Barrick safety policies. All Barrick underground operations have GCMPs in place, and its surface operations are now involved in the initiative. This paper presents Barrick?s global approach to underground mine ground control management and outlines the content and process for the development of a GCMP.

May 1, 2006

The Barrick Zaldivar mine is an openpit, heap-leach copper mine in Region II of northern Chile at an elevation of 3,300 m (10,826 ft), approximately 1,400 km (870 miles) north of Santiago and 175 km (109 miles) southeast of the port city of Antofagasta. In 2006, Zaldívar produced 307 million lbs of copper, with reserves estimated at 5.7 billion lbs. The mine uses conventional methods of openpit mining: Pure cathode copper is produced by three stages of crushing and stacking the ore, followed by heap leaching and bacterial activity to extract copper from the ore into solution. A solvent extraction and electrowinning process then removes the copper from solution and produces the cathode copper. A flotation plant also recovers copper contained in the fine fraction of the crushed ore. In 2006, an existing A-frame structure that covered copper ore from the mine?s secondary crushing operation was damaged beyond repair. The material delivery configuration of this original structure had the conveyor carrying incoming ore directly over the low roof to drop ore into the building at its peak, and ore trickling from the sides of the conveyor had accumulated on the roof, overloading it. A better solution had to be found, and fast: First, the Chilean Commission does not permit uncovered piles of this type since the extremely fine material leads to serious pollution problems. Second, Barrick Zaldivar is very concerned about worker safety, and the amount of dust created by the uncovered pile was not acceptable. Finally, some amount of copper was lost in the dust generated by the winds of the Andes. The major issues faced by Barrick Zaldivar in designing a new structure included:

Jan 1, 2009