Search Documents

By Efrem R. Reeves, David C. Byrne

This study was conducted as part of a project involving the evaluation of a new type of noise exposure monitoring paradigm. Laboratory tests were conducted to assess how “nonstandard” dosimeter microphones and microphone po­sitions measured noise levels under different acoustical condi­tions (i.e., diffuse ?eld and direct ?eld). The data presented in this article re?ect measurement differences due to microphone position and mounting/supporting structure only and are not an evaluation of any particular complete dosimeter system. To varying degrees, the results obtained with the dosimeter microphones used in this study differed from the reference results obtained in the unperturbed (subject absent) sound ?eld with a precision (suitable for use in an ANSI Type 1 sound level meter) 1/2 -inch (12.7 mm) measurement microphone. Effects of dosimeter microphone placement in a diffuse ?eld were found to be minor for most of the test microphones/locations, while direct ?eld microphone placement effects were found to be quite large depending on the microphone position and supporting structure, sound source location, and noise spectrum.

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920

By V. J. Hucka, J. H. Tu

"A computer model has been developed for evaluating the performance of truck and shovel operations in an open-pit mine. The data required for describing the haulage network are simplified and shift startup and ending procedures specific to any given mine can be incorporated into the model readily . The model uses a FORTRAN-based simulation language SLAM and can be tailored to the conditions and practices of a particular mine.The model is used to analyze truck and shovel operations, evaluate different haulage layouts in the planning stage, or compare the expected performance of alternative truck dispatching systems.Stochastic simulation is used to model the random variation in time required f or the individual activities. This gives a more realistic representation of the processes under study. Simulation runs show good agreement with actual performance. The model is especially useful for examining alternatives in equipment acquisition , haulroad design, truck-shovel allocation and dispatching methods. The results of such simulations provide a sound basis f or making major management decisions.IntroductionTruck haul age is widely used in open-pit mining operations. It is also the largest cost item in the operating costs of an openpit mine, in some cases accounting for an estimated 50% of operating costs(1) , Truck replacements, which are necessary from time to time, involve large amounts of cap ital. Increasing depth of mining and consequent increase in stripping ratios require additional capital investment in the truck-shovel fleet. The sharp rise in energy costs over the last decade has also contibuted significantly to an increase in truck fleet operating costs . All these factors have led mine operators to search for ways to improve the effectiveness of the truck-shovel fleet, in order to lower costs and maintain a profitable operation in the face of declining markets and increasing world wide competition.Control of truck haulage in an open-pit mine is usually done in one of two ways."

Jan 1, 1985

By T. M. Morris, F. M. Lewis, W. C. Lay, Gordon M. Bell

Part I of this chapter is concerned with the description of and metallurgical data pertaining to the flotation circuits used in the London mill of the Tennessee Copper Co., at Copperhill, Tenn. The ores treated at the London mill are massive complex sulfides, in which pyrrhotite and pyrite are the predominant minerals. Other sulfides are chalcopyrite and sphalerite; magnetite is also of economic value. The approximate mineralogical analysis of the ore is shown in Table 1. [ ] The chalcopyrite and sphalerite are closely associated with pyrrhotite as shown by the tracings of micrographs (Fig. I), which are representative of the mill feed. Fig. la illustrates the type of locking between pyrrhotite and chalcopyrite; Fig. lb illustrates the way in which sphalerite is attached. Thesephotographs indicate that it is not practical to break all of these attachments. Hence, in order to produce concentrates with satisfactory grades and recoveries, most of the locked chalcopyrite particles must be recovered into the copper concentrate, and the locked sphalerite-pyrrhotite particles must be separated from the iron concentrate. A copper concentrate, a zinc concentrate, and an iron concentrate are made. Typical metallurgical results are tabulated in Table 2. HISTORICAL In 1922 the London mill started as a copper concentrator, with a capacity of 300 tpd, and in 1926 an additional flotation circuit was added to recover the iron sulfide remaining in the copper tailing. In 1927 a zinc flotation circuit was installed between the copper and the iron flotation circuits. This procedure was not satisfactory because the iron recovery was low, due to the

Jan 1, 1962

By Shengli Wu, Jiacong Zhang, Mingyin Kou, Bingjie Wen, Heng Zhou

The COREX process, which is considered to be able to replace the blast furnace, still has some gaps to reach the designed productivity. The metallization degree is regarded as one of the limitations of the COREX process. In the present work, several parameters affecting the metallization degree of direct reduced iron (DRI) are analysed by SPSS software (Statistical Product and Service Solution). Melting rate, oxidation degree of reducing gas, oxidation degree of top gas, top gas consumption per ton of burden, temperature of reducing gas, and burden distribution index are con firmed as the main factors affecting metallization degree. Based on this, a linear equation has been developed for predicting metallization degree. Additionally, improving the melter gasi fier vault temperature appropriately, increasing the proportion of high volatile matter coal, and optimizing the type and particle size of iron ore and the pattern of burden distribution have been shown to improve the metallization degree.

Mar 1, 2018

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Mehmet Aksoy, Kagan Ozdemire

With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision. Therefore, determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. Although too many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects. This paper presents the results of ground vibration measurements carried out in Espey Open-Pit Boron (Colemanite) Mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study, ground vibration components were measured for 13 shots during bench blast optimisation studies in order to predict peak particle velocity level for this site. In blasting operations; ANFO and Powergel Magnum 600 (blasting agent), Powergel Magnum (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 4 different types vibration monitors (3 White Mini-Seis and 1 Instantel Minimate Plus Models). Then, the data pairs of scaled distance and particle velocity obtained from the 38 record events were analysed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance.

Jan 1, 2005

By M. F. Ameur, M. Habak, H. Aouici, M. Kenane

Present study interest by aluminium alloy (Al 7175-T5173) drilled without cooling fluid. The influence of the machining parameters (spindle speed and feed rate) on the holes quality was analyzed. Drilling tools are made of carbide (WC); high speed steel (HSS) and TiN coated carbide (WC-Ti).The Experiment design was reinforced by the application of statistical analysis of variance (ANOVA).The results show that the thrust force is influenced principally by the spindle speed and feed rate. Though, both feed rate and tool materials have statistical significance on the surface roughness. In addition, the objective of correlations between spindle speed and feed rate with the evolution of the machining parameters was established. These correlations were obtained by quadratic regression using the response surface methodology. Finally, useful to select optimum values of drilling parameters, that would minimize thrust force, torque, cutting temperature and surface roughness.

Jan 1, 2015

The National Institute for Occupational Safety and Health (NIOSH) has continued study of the Personal Dust Monitor (PDM) developed by Rupprecht & Patashnick Co. Inc. through a CDC contract and currently being commercialized by Thermo Fisher Scientific. This report examines the effect of oversize particles, cyclone inversion, and cleaning procedures. Clean and exposed filters were examined using light microscopy and particulates counted before and after various instrument manipulations. The data presented show that the dry cleaning procedures do not cause significant (greater than limit of detection) sample contamination by respirable or oversize particulates and that the cyclone is resistant to particulate carry over during inversion.

Jan 1, 2009

By H. F. Yancey

THE jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed at about -1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation Jüngst1 concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 4, 1925

By James Lee Hibbard, Doraiswami Ramkrishna

A population balance model accounting for the transient variations in drop size distributions in a stirred liquid-liquid system is analyzed for its effect on chemical reaction conversion in a stirred, batch reactor. The analysis is applied specifically for phase transfer catalytic reactions, which indicates that transient effects of evolution of drop size distributions may be important in such systems.

Jan 1, 1981

By Lijun Xu, Jan M. Mutmansky

The purpose of this research was to investigate airborne coal mine dust characteristics in order to assess the possibility of contribution of these characteristics to the incidence of coal workers' pneumoconiosis (CWP). The characteristics studied included physical (mass concentration and size distribution), chemical (elemental composition), and mineralogical (quartz and kaolinite content) variables of the dust. The results are based primarily upon analysis of the characteristics of 99 impactor samples from 18 mines in seven states. Because the eight stages of the impactor span the range of dust sizes up to 20 microns, the characteristics analyzed should represent respirable dust characteristics well and also provide size-dependent representations of the characteristics. In general, the patterns of mass concentration and size distribution in the various mines studied were similar with mass concentrations being high downwind of the continuous miner. The concentrations and size distributions were more variable upwind of the continuous miner, apparently as a result of the variations in the dust conditions in the working section. Significant size effects on the elemental and mineralogical content are shown in the data. Concentrations of most of the elements decrease as size decreases. However, minerals content increases as the dust size decreases. Regional variations of elemental and mineralogical content are also significant. Quartz and kaolinite contents are small in regions with low incidences of CWP. However, the elements of Cu and Zn are high by comparison to their content in high-incidence coal fields and may have the effect of protecting against the disease.

Jan 1, 1991

By Jeremy G. Kress

We propose the discrete element method (DEM) as a complimentary alternative to analytical solutions and FEM models for the analysis of pile response. DEM is a novel approach to the engineering design of deep foundations which can be used to provide insight into the mechanics of soil-soil and soil-structure interaction. It is common to use analytical, empirical, and semi-empirical methods to predict pile behavior, where if granular properties, pile length, or load orientation change, then significant adjustments are made in the design sequence. DEM provides a more uniform approach in granular soils. Based on constitutive force-displacement relationships and laws of motion in rigid and elastic bodies, few changes must be made for a wide variety grain types, pile types, embedment, and load orientation. Preliminary results for simulation of a single pile are qualitatively consistent with results from conventional design procedures and also provide significant information not available from other analyses (e.g., local information about interface failure during shear). Importantly, these analyses are portable to a variety of pile types and installation procedures, which may not be the case for empirical approaches. Given consistent increases in computing power and rapid advances in model speed and sophistication, the DEM should prove to be a robust method for design and the analysis of pile response in granular soils.

Jan 1, 2010

By Gandhi

Piled raft foundation under uniformly distributed vertical loads has been analyzed using Finite Element Method. The soil is considered to be linear elastic, isotropic, homogeneous. The raft,pile and the soil have been idealized with eight noded brick elements. Parametric study have been carried out varying pile length, soil modulus, raft thickness, and pile spacing. Design charts have been produced to achieve 50% load sharing between pile and raft for optimum design. Data available in literature is compared with the design chart results and found satisfactory.

Jan 1, 1996

By JO Choi

Jet-grouting method is a useful technique to reinforce foundations on relatively soft or vulnerable soil layers such as fractured zone and stratum with cavities. Although jet-grouting has been widely applied to various field works, a reliable design standard has not been established yet. A number of model tests were performed to investigate end bearing behaviors of piles reinforced by jet-grouting. It was concluded that end bearing capacity was increased in proportion to uniaxial compressive strength of grout column. Based on the test results, the design criteria for the end bearing capacity were suggested.

Jan 1, 2006

By A. T. Iannacchione

Underground mining of stone in the US is increasing, as is the depth of overburden above the mines. Data gathered from mine visits, maps, discussion with operators and numerical simulation have been used to investigate pillar design and recommend safe practice. Many pillars have slender shapes with relatively large adjacent mine openings: width-to-height ratios range from 0.54 to 3.13 and extraction ratios from 0.56 to 0.91. The pillar material is often very strong and average overburden only 80 m, but occasional failure due to excessive local stress has occurred where pillar size had been unintentionally reduced, overburdens were greater than 200 m, width-to-height ratios were less than 1.25 or extraction ratios were greater than 0.83. Pillars with width-to-height ratios of less than 1.5 appear more likely to fail under excessive stress. When width-to-height ratios fall below 1.0, defects such as through-running discontinuities can have a significant influence on stability. Dip, orientation and material properties are also important

Jun 21, 1905

By A. T. Iannacchione

Synopsis Underground stone mining Is an emerging sector of the U.S. mining industry. As this expansion takes mines under deeper cover, and as more efficient mining methods are utilized, effective stone pillar design methods will become even more Important. Current design practices are examined and a discussion of safe mine layouts is presented as a first approach towards weighing the demands for increased production against increased risk. Risks to underground stone-mine workers include rib Instabilities, pillar failures and roof falls. Seventy-two stone-mine pillar designs were examined. Pillars with width to height ratios of less than 1.5 appear more likely to fail when subjected to excessive stress levels. When width to height ratios fall below 1.0 defects in the pillars, such as through-running discon¬tinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties and orientation are also important determining factors in pillar strength. During the past three years the number of active underground stone mines in the U.S.A. has ranged between 90 and 100. This number is expected to increase as the crushed stone industry responds to growing demands for its products.1 As more of the industry moves to benefit from the advantages of underground mining production from underground stone mines is expected to increase above its current level of approximately 66 000 000 r/year. Parker2 identified four advantages of underground mining operations: (1) surface developments, zoning laws and environmental concerns are often less of an issue; (2) stripping and restoration requirements are eliminated; (3) additional reserves are often available beneath the quarry floor, under pit slopes or under an adjoining property; and (4) space is created for secondary use. Underground mines enjoy the added benefits of work in a constant underground climate, rather than in the variable surface climate, minimization of community concerns by placement of the crushing, sizing and stowing operations underground and reduction of surface vibration concerns through smaller blasts. The drawbacks of underground mining include added health and safety hazards for the stone miners, whose health can suffer from increased exposure to falls of ground, airborne contaminants and fog in large underground openings. Injuries from falls of ground in stone mines have occasionally exceeded the incidence rates for other mineral resources mined underground. 3 Existing underground stone operations, by comparison with stone operations a decade ago, mine more stone at a faster rate and with larger equipment. Because of high demand mines face increased pressure to yield more stone per production blast. A majority of the miners use the V-cut blasting pattern, which limits the depth or pull for each shot to about 4 m. Therefore, to produce more stone, either the mines must work more faces or existing faces must be enlarged. The enlargement of underground openings poses problems in the maintenance o€ strata stability, First, the widths of the mine entries partially control the amount of sag or deflection that any given roof beam can withstand before failure. This deflection can take pi ace quickly after an opening is excavated or much later as weathering processes form additional, thinner beams. Because increased deflection increases the potential for roof beam failure, there is a limit to how wide a room can safely be made. These limits depend on local geological and stress conditions and, to some extent, the cost effectiveness of roof-bolting. Given these room width limitations, underground stone mines have placed more attention on expansion of production through benching where mining thicknesses permit. The heights of rooms partially control the strength characteristics of adjacent pillars: as the room height increases for a given pillar width the pillar width-to-height ratio (w/h) decreases. In general, stone pillars are very strong, but when the width-to height ratio diminishes the potential for pillar rib instabilities and pillar failures increases (see Fig. 1). [ ] In the underground environment the desire to utilize wider rooms, higher benches and multi-level mining results in the potential for unstable ground conditions. Although the number of failed pillars is currently very low, the potential for additional failures will grow if more slender pillars are developed, especially under deeper cover, with wider mining sections and in multi-level operations. It should also be noted that the passage of time acts to decrease the strength of many existing pillars. An examination of current design practices

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By S. Kelebek, E. Yalcin

"Diethylenetriamine (DETA) and/or triethylenetetramine (TETA) are reagents that can generally be categorized under ""flotation modifiers"". These polyamines are known to be effective for the deactivation/depression of pyrrhotite that is present in Canadian nickel-copper sulphide ores in large quantities. Recent bench scale testing on some of these complex ores indicated that chalcopyrite flotation can also be adversely affected under certain conditions involving polyamines, which may be taken to be an evidence of their specific affinity towards chalcopyrite. In general, DETA shows no significant depressant action on chalcopyrite while TETA's promotion of hydrophilicity for this mineral has been observed even in the presence of xanthate. This prompted an investigation on thermodynamic equilibria involving these polyamines and copper ions. Results serve a useful purpose to identify conditions for deactivation phenomena. CuDETA2+ and CuTETA2+ chelates as products of sequestration have large predominance areas covering a wide range of redox and pH conditions, where copper xanthate species are not stable, especially in the presence of TETA."

Jan 1, 2009

By C. B. Piazzarollo

Red Ceramic materials are widely used in Civil Construction in Tropical Countries. However, these materials have high porosity and low mechanical strength. Thus, in order to improve these properties, recycle mineral wastes was incorporated into clay from Campos - RJ, ornamental rock waste, from the gneisses cutting of Cachoeiro - ES, 150 km from Campos. After the addition of up 10% of waste in clay mass, ceramic pieces were produced and subjected to the tests of porosity (P) and flexural strength (FS). The test material contains 53.3% clay and 67% waste slit. The X-ray diffraction identified the presence of kaolinite, quartz and feldspar for the clay and, for the waste, quartz and orthoclase. The results of FS and P showed that the residue influenced, positively, the ceramic piece, with strength gains especially from 920º up to 960°C.

Jan 1, 2015