Search Documents

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment, these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In U.S. Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center's 900-lb per hr pilot plant, approximately 85% of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to 51000 ppm equivalent SiO*, while maintaining a Ca(II) content of =16 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water. Water quality is perhaps as important to flotation as are the reagents used. The character of water is extremely variable, depending on whether the source is a well, lake, or stream, upon the season and temperature, upon prior use, and upon the character of the watershed. All of these factors influence the water hardness and the quantity of other dissolved inorganic salts, turbidity, dissolved and suspended organic matter, dissolved gases, and pH. Frequently, the differences in water quality can measurably influence flotation selectivity, often to the point of spelling success or failure. Water hardness is particularly troublesome in flotation systems employing fatty acids, but other unrecognized constituents may also contribute to peculiarities in flotation behavior. Furthermore, a given water source may be entirely satisfactory in one flotation system, but entirely inappropriate in another. In recent years, society has given more attention than formerly to water use, even in areas where water is plentiful. However, both the demands of a growing population, with increased per capita needs, and also those of industry must be met. As a result, riparian rights must be negotiated with the appropriate government agency or agencies so that consumption of water is often allocated or otherwise controlled. Furthermore, the disposal of off-process industrial and domestic water is coming under the increasing scrutiny of these same governmental units. In these respects, the mineral industry is no exception, so that conservation, water reclamation, and reuse may be expected to assume increasing importance. In 1932, it was stated that, "water reclamation is generally more expensive than the economy in water and reagents resulting from its use. It is employed only if it is urgent to save water."' The economic aspects of this statement may still be true, but the unrestricted use of water is becoming less and less an option of the user. The purpose of this paper is to discuss an investigation conducted by the U.S. Bureau of Mines (USBM), in which water reclamation and treatment were undertaken to develop procedures for, and to assess the effects of, water reuse on the flotation treatment of nonmagnetic taconites. This investigation is a logical extension of previous work described by the author and associates at the Twin Cities Metallurgy Research Center employing selective flocculation-desliming and anionic flotation of silica from low-grade, nonmagnetic iron ores2,8 The requirements for the selective flocculation-de-sliming and the anionic flotation of silica processes determined the direction of the investigation. Previous studies had indicated that pH levels of about 11.0 and 11.8 were required for selective flocculation and flota-tlon, respectively. The calcium content of the water was believed to be of importance in both of these operations, and since Minneapolis tap water with a Ca(I1) content of about 16 ppm had been successfully used, an attempt was made to reclaim the process water at an equal level of dissolved calcium. Additionally, the objective was to nullify or effectively limit the effects of dispersants and fatty acid residuals from prior stages of processing. Last but not least, the system of water treatment had to have the capability of reducing turbidities to workable levels. With about half of the effluent being derived from the selective flocculation-desliming step and carrying about 25,000 ppm of highly dispersed, suspended fines, this last objective appeared formidable at the outset. Procedures for water reclamation were derived, in part, from well-known mineral dressing practices, from past observations and investigations, and from concepts contained in various pertinent publications on water treatment."c These procedures involved: 1) flocculation with lime and poly electrolyte-type flocculants, 2) lime-soda-ash softening, 3) chemical precipitation, and 4) mineral surface adsorption. Control was exercised at various stages of water reclamation by frequent measurements of Ca(11), pH, and turbidity.

Jan 1, 1971

By A. D. Rovig, D. W. McGlashan, Donald M. Podobnik

Crystal-chemical and stntctural properties of sulfide minerals are considered. The information gained is to be used to interpret (I ) freshly broken mineral surfaces, (2) modifications of the mineral surfaces, and (3) reactions at the mineral surfaces. From these basic disciplines, concepts with regard to the changes that surfaces undergo, reactions that might take place, the geometry of the interface, the state of different atoms and ions in the interface, and other physical and chemical properties of an interface must be developed, weighed and applied. The authors first deal with these conceptual considerations from which hypotheses are set forth to describe the environ men tal-interfacial relationships for several sulfide minerals. Qualitative and quantitative explanation of par-ticulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occurring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc., on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental-interfacial relationships for sulfide minerals. GENERAL CONSIDERATIONS Interfacial Reactions:Interfacial reactions are the cruxes of flotation schemes as well as other processes such as thickening, filtration and hydrometallurgy. However, as noted by Klassen and Mokrousov: 1 "The problems concerning the surfaces of natural minerals, the laws governing simultaneous adsorption from aqueous solution on these surfaces of a whole series of reagents, the laws of the surface reactions and the properties of water layers separating the minerals, are all known to a first approximation only." An investigator has the privilege of postulating methods of solid-liquid interfacial reactions. REACTIONS WITH WATER - Water consists of hydronium (H3 O 4) and hydroxyl (OH-) ions in the ionized state. That this is so forms the basis for the postulated reaction of the hydrated hydrogen ion with net-negative mineral surfaces as depicted in Fig. 1. In this case water is bonded to mineral surfaces through hydrogen-bridge-type bonds - possibly hydrogen bonds. Although bonding of the van der Waal type may be responsible for this reaction, it is most likely that stronger bonds are involved. Once firmly bonded to the surface, the water layer is known to be quite tenacious. It is further speculated that a shear plane exists at some distance (see Fig. 1) away from the mineral surface. Exact location of this plane is not known, but in all probability it will be positioned across a weak bond of the hydrogen-bond type where the surface-attached water is coordinated to the original hydrated hydrogen ion. REACTION WITH METAL IONS - Klassen and Mokrousov ' state: "The presence of an ion in water leads to an immediate formation around that ion of a highly condensed atmosphere of water dipoles and thus to hydration of the ion." The fact is known that multivalent cations are strongly hydrated, usually by six or eight molecules of water, and that anions are not so strongly hydrated. Conceding the fact that thermodynamics, concentration, pH, and physical considerations are of utmost importance in truly explaining a mechanism of metal ions reaction with a hydrated mineral surface, it does seem logical that the mechanism illustrated in Fig. 2 is feasible. In this reaction, the metal ion (M) is coordinated in one dimension - to the mineral-surface hydration layer. Note also that explanation of this reaction requires that the shear plane move to a less stable bond configuration; that is, the shear plane has moved to a position between the metal ion and the other coordinated water molecules which are more free to dissociate. Reactions as depicted in Fig. 2 should cause the formation of an apparent mineral surface which is net-positive. Immediately, it must be noted that measurements of apparent-mineral surfaces serve - within limits - to indicate a degree of ion-surface reaction capability. The major limiting factor he re is one related

Jan 1, 1970

By S. W. Nabbs, W. D. Bachman, A. W. Last

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from. Kennecott Copper Corp.'s Chino mine. The grindability of the various samples was found to vary over an extremely wide range, even among samples taken from diflerent locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale nonhomogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully. In the past 15 years, comminution by primary autogenous grinding has been investigated and applied economically in the minerals industry, particularly in iron-ore processing. Successful application of primary grinding is described by A. A. Dor,l.' P. B. Dettmer,334 R. R. Turner, and W. F. McDermott." other authors describing the advantages of primary grinding include H. Hardinge,' R. T. Hukki,' D. S. Coyle" and F. C. Bond,"," to mention only a few. For the past several years, Kennecott Copper Corp.'s Metal Mining Div. Research Center has been investigating primary grinding of disseminated copper ores. Both fully autogenous and semi-autogenous grinding has been explored. Ores from three of Kennecott's western operating properties and from several development properties have been tested. Host rocks include diabase, schist, silicated and argillaceous limestones, shale, granite porphyry, quartzite, and granodiorite. The object of this paper is to supplement the general knowledge in the field of primary grinding by presenting information gained from the studies with the various disseminated copper ores. Data are presented which show that carefully considered test programs are required to determine the practicality of applying autogenous grinding to a specific mining-beneficiation operation. Particularly this is so if more than one rock type occurs within an ore body or if there are wide variations in the degree of rock alteration within a deposit. Extensive sampling and subsequent testing of the ores within a mine are required if serious pitfalls are to be avoided and good engineering data acquired. We hope that this presentation will stimulate studies to increase the understanding of the fracturing process applicable to large pieces of rock, a factor which is important in autogenous grinding. Test Facilities and Procedures Both pilot-scale and full-scale test facilities were used to investigate primary grinding characteristics of the disseminated copper ores. A 6-ft Hardinge Cascade mill, a 24-ft Hardinge Cascade mill, and a 5-ft Aerofall mill were used in the studies. The Cascade mills were operated wet, while the Aerofall mill was operated both wet and dry. The Cascade mills were operated both for fully autogenous and for semi-autogenous grinding; the Aerofall mill was operated only semi-autogenously. Fully autogenous grinding, as the term is used in this presentation, is defined as the direct grinding of coarsely crushed rock by the action of the rock mass. Semi-autogenous grinding is defined as the grinding of coarsely crushed rock with the rock mass supplemented by a steel ball charge. Most of the test work was done using the 6-ft Cascade mill, operated under fully autogenous grinding conditions. Only limited testing was conducted with the 5-ft Aerofall mill and only one ore was tested using the 24-ft Cascade mill. This presentation is concerned, therefore, primarily with fully autogenous, pilot-scale grinding in the Cascade mill. Fig. 1 presents a diagram of the test facilities used with the 6-ft Cascade mill. Principal test equipment consists of a 6-ft Cascade mill, an 18-in. spiral classifier, an elevator, a 2 x 9-ft belt feeder, a conventional integrating kilowatt-hour meter, and a recording wattmeter. In testing, feed charges, adjusted as to weight, were deposited as evenly as possible on the belt feeder every 15 min. The weight of each charge was adjusted to maintain a mill charge of 27 to 30% of mill volume. The classifier was adjusted to obtain the desired size-consist of the final product, generally at 20% + 100 mesh. After equilibrium was established in the circuit, the feed, mill discharge, classifier sand, and classifier overflow were sampled and their size distributions determined. During the sampling periods, the power drawn by the mill was measured to determine the energy consumed in the reduction of the size consist of the ore solids. Fully Autogenous Pilot Grinding Tests on Various Kennecott Ores Typical test results obtained in the 6-ft Cascade mill with samples from Kennecott's Ray Mines Div., Chino Mines Div., Utah Copper Div., and a development property designated as Mine A are presented in Table 1. As shown, the ores that were ground most easily in the pilot-scale mill were composite mine samples obtained

Jan 1, 1971

By C. E. Taylor, L. V. Fegan

With on-stream electrical-resistance measurement as a basis, Bethlehem Steel developed a system for the completely automatic control of moisture in the feed to pelletizing. This system was later successfully adapted to the sintering process, with automatic control of moisture serving to maintain the air permeability required for effective burnthrough. Control of moisture content is an important factor in the agglomeration processes by which iron ores are converted into either pellets or sinter for use in blast furnace burdens. In both pelletizing and sintering the iron ore feed must be mixed with the proper amount of water so that capillary attraction and surface tension forces can be utilized to cause the ore particles to coalesce and form larger agglomerates. The success or failure of the entire pelletizing or sintering process depends on maintaining the proper moisture. Therefore, continuous automatic control of moisture is one of the conditions for the automation and optimum use of both pelletizing and sintering processes. In pelletizing, variation in moisture can cause ball size to change and is a common cause of cycling which results in a fluctuating feed to induration. Excessive moisture can cause lumps to form at the cutter bar and contributes to the formation of buildup on the green pellet screens. Green pellets with excess moisture deform and reduce bed permeability. In sintering, accurate control of moisture is also important because moisture must be within the limits that give the bed the required permeability for good burnthrough. In response to these problems, a moisture meter, based on the principle of electrical resistance measurement, was developed. This moisture meter has been a key factor in the development of systems for providing uniform feed of concentrates in most of Bethlehem's pelletizing and sintering plants. The automatic moisture control system for pelletizing was successfully plant-tested and resulted in the following: (1) Control of moisture in the green pellets to +0.2%. (2) Up to 50% reduction of bentonite consumption. (3) Control of unscreened green pellets so that 85% of the furnace product at Cornwall was within the size range of -5/8 +3/8 in. (4) Improved quality of product with a tumble test of 94 and a "Q" index of 90 as the result of feeding a consistently uniform feed to a shaft furnace. In sintering, where sinter-mix temperature change and variable feed could cause errors in moisture measurement, the system was designed to maintain the correct moisture under virtually all plant operating conditions. It was successfully plant-tested and is now in use in most of Bethlehem's sintering plants. The system achieves: (1) Control of moisture within the desired limits for optimum production. (2) Continuous measurement and control of moisture even with intermittent feeding of mix, so that attention by the operator is seldom required. The two automatic control systems provide smoother startup, minimize upsets and contribute to the consistent control of process variables in pelletizing and sintering. MOISTURE-CONTROL SYSTEM FOR PELLETIZING Fig. 1 shows the general arrangement of the system for automatic control of moisture in pelletizing.1 In this system a bin level controller, using a single probe which regulates filter speed, maintains a uniform low concentrate level in the bin.' The moisture meter, comprised of an analyzer and control components, continuously measures the moisture in the bed and adds water to adjust to the desired level. The meter is placed in an open-loop (feed-forward) control, i.e., water addition occurs downstream from the probes. Filter vacuum must be set so as to produce a filtercake moisture which is below the optimum for pelletizing. Bentonite is added after the

Jan 1, 1969

By William B. Stephenson

The paper describes efficient and effective methods of automatically controlling sand pump installations. Particular reference is made to liquid-level controls actuating variable speed pump-driving units. Included is a discussion of various combinations of equipment, with schematic drawings. HERETOFORE many sand pump installations in the mining and metallurgical field involved guesswork as to the size of the pump and then simply direct-connecting it to a constant speed motor which was often large enough to do twice the work required. Considerable thought was given to mill location in an effort to avoid as much pumping as possible. Hillside design of mills with gravity flow of tailing was much to be desired. Power costs were low, construction was relatively cheap, and labor in many places meant nothing in comparison to the values derived from the ores being treated. Today most of these conditions are reversed. Ores are becoming more complex with lower values per ton of ore treated. Power is more expensive, construction is higher, and labor definitely takes a very important place in the profit and loss statement. Each piece of equipment incorporated in the design of a new mill is selected to provide highest efficiency based on careful metallurgical analysis of the ore to be treated both in good and poor markets. Each is designed with its flexibility in mind and with provision for adjustments in its performance to meet actual conditions in the operation of the mill. Sand pumps have taken an important position in mill design. Operators the world over are relying more and more on the performance of a sand pump in the efficient operating of their plant. Many ordinary jobs are being done today with pumps driven through adjustable pitch diameter V belt drives in order that changes in pump speed can be made easily to meet actual operating conditions. Operating costs have long since proved the folly of operating a pump at too high a speed for the volume and head to be overcome. Metallurgical results have shown the benefits derived from a smooth flow as contrasted with a surging flow from an uncontrolled pump. Construction costs have risen to such an extent that surge bins and other means formerly employed must be omitted from today's flowsheet. Several installations of considerable size and involving the use of automatic pump speed control have proved the adaptability of such controls since they were placed in service in recent years. In the following presentation each system discussed and illustrated schematically has been installed in one or more instances and has proved itself reliable and definitely economical from the standpoint of capital investment, operation and maintenance. Variable Volume-Head Speed Control: Probably the most popular, effective and efficient automatic control setup for sand pumping installations is the one shown schematically in fig. 1. Commonly used

Jan 1, 1951

By William B. Stephenson

The paper describes efficient and effective methods of automatically controlling sand pump installations. Particular reference is made to liquid-level controls actuating variable speed pump-driving units. Included is a discussion of various combinations of equipment, with schematic drawings. HERETOFORE many sand pump installations in the mining and metallurgical field involved guesswork as to the size of the pump and then simply direct-connecting it to a constant speed motor which was often large enough to do twice the work required. Considerable thought was given to mill location in an effort to avoid as much pumping as possible. Hillside design of mills with gravity flow of tailing was much to be desired. Power costs were low, construction was relatively cheap, and labor in many places meant nothing in comparison to the values derived from the ores being treated. Today most of these conditions are reversed. Ores are becoming more complex with lower values per ton of ore treated. Power is more expensive, construction is higher, and labor definitely takes a very important place in the profit and loss statement. Each piece of equipment incorporated in the design of a new mill is selected to provide highest efficiency based on careful metallurgical analysis of the ore to be treated both in good and poor markets. Each is designed with its flexibility in mind and with provision for adjustments in its performance to meet actual conditions in the operation of the mill. Sand pumps have taken an important position in mill design. Operators the world over are relying more and more on the performance of a sand pump in the efficient operating of their plant. Many ordinary jobs are being done today with pumps driven through adjustable pitch diameter V belt drives in order that changes in pump speed can be made easily to meet actual operating conditions. Operating costs have long since proved the folly of operating a pump at too high a speed for the volume and head to be overcome. Metallurgical results have shown the benefits derived from a smooth flow as contrasted with a surging flow from an uncontrolled pump. Construction costs have risen to such an extent that surge bins and other means formerly employed must be omitted from today's flowsheet. Several installations of considerable size and involving the use of automatic pump speed control have proved the adaptability of such controls since they were placed in service in recent years. In the following presentation each system discussed and illustrated schematically has been installed in one or more instances and has proved itself reliable and definitely economical from the standpoint of capital investment, operation and maintenance. Variable Volume-Head Speed Control: Probably the most popular, effective and efficient automatic control setup for sand pumping installations is the one shown schematically in fig. 1. Commonly used

Jan 1, 1951

By J. W. Axelson, J. N. S. Kwong, J. T. Adams, E. L. Pire, J. F. Johnson

CRUSHING has always been a major operation in the chemical and metallurgical industries, yet little is known about the theory of crushing, and today, the design of crushers is still based almost entirely on empirical knowledge and accumulated practical experience. In view of the increasing national need for the economic working of poorer grades of ores, the lack of a fundamental understanding of this unit operation hardly presents a satisfactory situation. Basic investigations of crushing have been concerned mainly with three phases of the problem, 1—the mechanism of the fracture process itself, 2— the particle size distribution of the crushed product, and 3—the relationship between the energy input and the amount of new surface produced. Probably adequate information on these phases will be required for a comprehensive understanding of the process of crushing. A bibliography covering these phases will be given as well as a review of the work done in recent years at the University of Minnesota on the relationship between the energy input for crushing and the amount of new surface produced. Fracture of Solids This phase of the crushing problem is the most fundamental because it is concerned with the actual mechanism of fracture. The main problems in a study of the fracture process are concerned with the questions of why and how fracture occurs and why there is such a discrepancy between the actual and theoretical energies needed in a fracture process. In considering the how of fracture, Poncelet40 carried Out experiments On the crushing of glass under compression. Actual photographs were taken of the glass plates in various stages of fracture-From these experiments Poncelet was able to postulate a probable mechanism of fracture. Probably because of the quantitative nature of the problem, considerable effort has been expended to find an explanation for the low tensile strength of materials and the conversely high energy for crushing. Tensile strengths are often only 1/500 of the theoretical while the energy for crushing is usually at least 500 times the theoretical. A review of the work to explain the low strength of glass is given by Weyl,52 in which the work of Griffith," Joffe,32 and Powell and Preston " are discussed. In a recent paper Seitz46 holds that the presence of flaws and fissures, as originally expounded by Griffith, is the most probable reason for the low strength of metals. Since a mass of data has been accumulated on the fracture strength of materials, several investigators have attempted to correlate this data in the form of an equation. Glathart and Preston," Taylor,40 Ponce-let,40 Machlin and Norwich," and Frederickson and Eyring,20 have all considered this problem, and the final relationship has always been that the stress for fracture is proportional to the logarithm of time. Murgatroyd30 arrived at a very similar relationship by a different method. The study of the fracture process has used many methods. Among some of these are the thermody-namic approach used by Furth21 which was based on the work of BornxL and later used by Saibel,43 and the statistical method applied by Fisher and Hollo-mon.10 In recent years metallurgists have concerned themselves with the problem of brittle .fracture as opposed to the usual plastic failure of metals. The great amount of interest shown is reflected by the number of contributors to the recent symposium on the fracture of metals.' Repeated failures of welded ships during World War II have accelerated these Studies.31,50,34 The shifting of thought from an emphasis on the

Jan 1, 1952

By C. C. Harris

An analytical solution of the integro-differential equation of batch grinding is proposed as a first appoximation to the xYt surface. The size distribution equation (xY plane) is a three parameter equation previously suggested. Possible refinements are outlined. Comminution kinetics research is presently following several related courses. Some are equivalent, in that they represent different ways of viewing the same facet of the problem, though the entire endeavor cannot be described as being completely integrated. The purpose of this note is to propose and discuss a framework into which the various approaches might be fitted. This must clearly be founded upon an analysis of the xYt surface.' (See also Fig. 1 of Reference 26.) The investigations referred to above comprise mainly researches into the following: (1) The kinetics of the creation of the finer sizes during relatively small grinding times. This is the Fahrenwald-Arbiter-Bhrany 2-3 approach which leads to equations equivalent to a special case of the charles4 relationship. It emerges that initial production of fines follow essentially zero order* kinetics. (2) Disappearance kinetics of the coarser fractions. This appears to be a first order relationship.5-6 (3) Prediction of the xYt surface via the selection and breakage functions utilizing computer-programmed or approximate solutions of the integro-differential equation of batch grinding.5,8-17 A recent discussion by Mika et al.5 references the relevant literature up to about 1966. In addition to these main-stream researches there is some work on the minor topic of extremely long grinding time considered as a limiting case.18-19 The field is supported by investigations into the size distribution of fragments produced by breakage processes, some of this work being most valuably statistical-mechanical in nature.20-25 Better fitting equations, however, are obtained by statistical and curve-fitting methods.26 This

Jan 1, 1969

By K. A. Natarajan, I. Iwasaki

Platinum electrodes are not inert as often thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g, in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measure ments in water-oxygen, iron-water-oxygen, and manganese-water-oxygen systems. Stability relations between Fe++ and Fe (OH), and between Fe (OH), and Fe (OH), were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions. Platinum electrodes have often been used in the measurement of dissolved oxygen concentrations and of redox potentials (Eh) in a variety of fields, e.g., analytical chemistry,' corrosion," geology and mineralogy,,'' biology,"' sewage treatment,' * hydrometallurgy,"I" and flotation."la The effectiveness of Eh-pH diagrams, first reported by Pourbaix' in 1949, has contributed much towards the theoretical understanding of numerous problems encountered in the metallurgical industry. Not many references are available in the literature, however, wherein attempts have been made to confirm Eh-pH diagrams from experimental measurements. One reason might be that, in spite of the apparent simplicity of the electrochemical technique, the direct measurement of Eh involves complex practical problems.' Factors such as the purity of the solution, the type of electrodes used, the history of the indicator electrode, and the type of atmosphere (namely, oxidizing, reducing, or inert) do have effects on the measured Eh values. The influence of mixed potentials cannot be underestimated. The poisoning of platinum electrodes by organic and inorganic impurities present in the solution may lead to erratic results. Platinum, commonly thought to be an inert electrode material, is not really so, as attested by a number of previous investigators who advised caution concerning the anomalous behavior of platinum electrodes in various electrochemical measurements.'" In the present article, a few pertinent experiments related to Eh-pH measurements in systems of interest in the metallurgical and water pollution fields are described in an attempt to correlate such information with what is already known, especially in the electrochemical literature. Iron-water and manganese-water systems were selected with a view of studying the correspondence between experimentally observed and theoretically established equilibrium lines. The work included an investigation of the behavior of platinum electrodes with respect to pretreatment and adsorption characteristics, the measurement of dissolved oxygen concentrations and their relation to Eh, the determination of the electrode potential of the ferric-ferrous couple at different pH, and the measurement of oxidation potentials in iron-manganese leaching systems. Experimental Procedure A rotating platinum electrode was used in many of the measurements to study the effect of rotation on measured Eh values. The electrode made by the Pine Instrument Co. consisted of a stainless steel rod with a platinum disk soldered to the end. It was covered with a Teflon insulation along the sides, so that only the circular tip of the electrode was exposed to the solution. Prior to its use, the platinum surface was brightened on a metallurgical polishing wheel with alumina as an abrasive, unless specified otherwise. The electrode was rotated with a Sargent cone-drive motor at 350 rpm. The contact of the electrode with the external circuit was made by filling a notch at the top of the stainless steel shaft with mercury and by dipping a copper wire into the mercury pool. The performance of the rotating platinum electrode was compared with the performances of a Beckman platinum button electrode and a platinum wire electrode. All the potentials were measured with respect to a saturated calomel electrode. A saturated KC1-agar bridge was used to minimize the liquid junction potential. A Beckman Zeromatic pH meter together with a Beck-man electrode switch was used to measure both the Eh and pH. A double-walled, all-Pyrex jar with a capacity of about 1 liter and themostated by circulating water of constant temperature was used for a reaction cell. Four equally spaced ports in the cover provided access for a glass electrode, a salt bridge connecting the saturated calomel electrode, a dispersion tube for bubbling gases into the cell solution, inlet and outlet tubes for passing the desired gases over the solution, and a graduated burette for introducing reagents from outside. The rotating platinum electrode was inserted through an opening in the top-center of the cover, and a positive gas pressure was maintained inside the cell to prevent air from entering into the cell compartment. A magnetic stirrer was used to mix the solution inside. For the determination of dissolved oxygen in the test solutions, the polarographic techniquex was used.

Jan 1, 1971

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

By C. D. Thompson, D. C. Violetta, C. A. Czako

The mechanics of the continuous sintering process are briefly reviewed and the application of this process for the beneficiation of principal minerals used in making cement is shown. Pilot plant tests using pyrobeneficiation techniques were conducted with mixtures of limestone and shale in various ratios. Results are illustrated and show the percentage removal of carbon, carbonates, sulfur, alkalies, and volatiles as a function of the limestone-shale ratio. Tests with varying quantities of solid fwls, added to mixtures containing limestone and shale in a 4 to 1 ratio, were made to attain optimum elimination of the volatile constituents. Experimental results show that 90 pct of these constituents were removed during the calcination sintem'ng process. The advantages of using the beneficiated material for making cement are discussed with regard to prepam'ng, handling, and clinkering operations. A sintering process for treating raw materials or kiln waste products which contain high amounts of alkaline materials is described. Tests were performed with a high alkaline waste dust mixed in a 1 to 1 ratio with raw cement meal. The data from these tests and others using different halides for aiding alkali removal are evaluated by the alkali content of the cement clinker. Test results showed that the Dwight-Lloyd process could be applied with facility in beneficiating raw materials for cement making. Substantial quantities of deleterious volutile constituents were removed by calcining and sintering techniques. The continuous sintering process has been applied for a number of years as a means of beneficiating minerals for subsequent conversion to merchantable products. The process was developed and first used for nonferrous metallurgical applicatfons. However, it has risen to prominence for ferrous metallurgical applications where last year in the U.S. and Canada nearly 40 million tons of iron ore were treated by grate firing processes. Through the years of process development many investigators have realized the versatility of the sintering process and have directed experiments toward the use of it for applications with nonmetallic minerals. These have included calcining limestone, carbonizing coal, expanding shale, and burning cement raw meal. Today commercial sintering plants produce cement clinker from mixtures of limestone and shale, lightweight aggregate from shale or clay, and calcined products from phosphate shale. The mechanics of the downdraft sintering process have been presented by many authors. In general practice the materials to be agglomated are mixed as moistened fines with a solid fuel and this mixture is spread uniformly on the grates of the sintering machine. The charge is then momentarily directed under an ignition furnace. After ignition a continuous downdraft of air promotes combustion of the fuel and through heat transfer particles become partially fused into a coherent mass. This is cooled from continued draft induced after combustion. Many investigators have shown that distinct zones are formed during the process of sintering iron ores. At the midway point of the sintering process these are prominent and are, respectively, from the top of the bed to the bottom, comprised of a cooling zone of sintered material, a combustion zone of sinter formation, a calcination zone, a drying zone, and a zone of unreacted materials. Completion of sintering occurs near the discharge end of the machine where the firing zone approaches either the grates or grate dressing material called hearth layer. Here the peak draft temperature usually can be noted in the windboxes. The zonal pattern has been illustrated with the use of graphs which show thermal gradients as they progress through the bed of materials during sintering. Fig. 1 shows, in simplified form, thermal gradients existing when clinkering cement on a sintering machine. The thermal gradients illustrated are for periods of initiation, midway and completion of the clinkering process. The occurrence of these zones has importance for the beneficiation of cement raw materials. A research program was performed at the Dwight-

Jan 1, 1961

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles. The first commercial unit employing the new thermoadhesive method of dry separation of minerals was installed at the Detroit mine of International Salt Company in Detroit, Mich. (Fig. l). This unit was first put into operation in March 1957. The purpose of the Detroit installation was 1) to serve as a pilot plant for evaluating the process on a commercial scale and 2) to produce marketable quantities of rock salt of improved quality and ap- pearance. The design of this plant was based on the results and information obtained from a 1-tph pilot plant at Battelle Memorial Institute. DESCRIPTION OF PLANT Location: The separation plant was installed underground near the crushing and screening plant, for this was the most suitable location from the standpoint of material handling. Furthermore, ample space was availabe at this location. Because the process requires a relatively constant temperature, the uniform year-around temperature of the mine (57°F) gave an added advantage to an underground operation. Feeding: The rock salt is conveyed to a surge bin, from which it is fed to the heating unit by a conveyor. The feed-rate control consists simply of an adjustable gate at the bottom of the surge bin. The plant may be fed either No. 1 grade of rock salt (0.279 to 0.375 in.) or No. 2 grade (0.375 to 0.500 in.) with a maximum input capacity of 500 tons per 15-hour day. Heating Unit: The heating unit (Fig. 2) consists of a panel of infrared lamps suspended inside a low-speed revolving screen. The radiant-heat panel, which is curved for most effective utilization of the heat, holds 240 infrared lamps of standard industrial type, each rated at 500 watts. The position of the panel is adjustable so that it can be placed centrally over and to within 6 in. of the salt bed on the screen. The entire heat panel is suspended by rollers in ¦ R. J. Brison and O. F. Tangel: Development of a Thermo-adhesive Method for Dry Separation of Minerals.

Jan 1, 1961

By R. M. Hays

At the present time, oxidized taconite and semitaconite are not processed on the Mesabi Range except in vely limited tonnages. However, it is estimated that by 1990 shipments from the Range will approach 75 million tons of iron ore per year. To achieve this and future production, either additional magnetic taconite reserves must be proven or oxidized taconite and semitaconite must be processed. One beneficiation process which uses high-intensity magnetic separation and flotation for concentrating oxidized taconite and semitaconite is described. Detailed metallurgical results are given and an economic evaluation of the process is presented with comparison to other processes. The results of the present study indicate that the high-intensity magnetic separation and flotation process appears nearer commercialization for the processing of Mesabi Range semitaconite. The disadvantages of the process are nearer solution and are being solved by well-defined programs. During the twentieth century, the Mesabi Range in northeastern Minnesota has been the main source of iron ore for American steel mills. The Mesabi Range, which is about 120 miles long and up to 3 miles wide, is the pre-glacial outcrop of a group of sedimentary iron-bearing rocks known as the Biwabik formation. The formation, which is 200 to 650 ft thick and dips 50 to 10° to the southeast, is divided into four stratigraphic units. From top to bottom, these are the Upper Slaty, Upper Cherty, Lower Slaty, and Lower Cherty. Since its deposition in Precambrian time, most of the original Biwabik formation has been subject to alteration. Thus, although the iron content of the original formation was quite uniform, major variations in mineral composition now occur both laterally along the length of the formation and vertically within its units. Details of the mineralogical variations in the Biwabik formation have been described by Wolff,' Gruner, 2 and White.3 The unaltered portion of the Biwabik formation includes the magnetite taconites which are being commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons of iron ore pellets per year and have produced approximately 170milion tons of pellets since 1956. Capacity for another 30 million tons of pellets per year is being considered by the industry for the next ten years. This increase will be obtained by constructing new plants and by expanding present operations. Thus, by ! 978, it is estimated that approximately 60 million tons of iron ore vellets will be produced each vear from the magnetite taconites of the Biwabik formation. The portions of the Biwabik formation subjected to intense alteration resulted in direct shipping, wash, and heavy-media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron ore for American steel mills. In 1967, about 11 million tons of direct shipping ore and 13 million tons of wash, jig, heavy-media, and other gravity concentrates were shipped from the Mesabi Range.4 These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from 24 million tons in 1967 to 6 to 8 million tons in 1975.' This decrease will

Jan 1, 1970

By N. J. Sather

A detailed description is given of Bunker Hill's concentration process employed at the company's lead-zinc property in the Coeur d'Alene district, Idaho. The plant is equipped to process 3000 tpd of Pb-Zn ore. The history of the Bunker Hill mine dates back to Aug. 26, 1885, when Noah S. Kellogg found the outcrop of the Bunker Hill orebody on the hillside of Milo Gulch above the present town of Wardner, Idaho. A small concentrator was erected in 1886, and before the railroad came, the mine output was transported by mule teams to the head of navigation on Coeur d'Alene Lake. After ten years of production, an interest was purchased in the Tacoma smelter at Tacoma, Wash., to which the entire output was shipped. In 1916 and 1917, a modern lead smelting plant and refinery was erected, and a modern electrolytic zinc reduction plant was built in 1927-1928 by the Sullivan Mining Co. which was 50 pct owned (and now totally owned) by the Bunker Hill Co. The first concentrator, a 100-tpd capacity plant, was built in 1886 near the Reed Tunnel in Wardner. The treatment consisted simply of crushing ore to 2 in. and then to 1/2 in. through rolls in closed circuit with a bucket elevator and trommel screen. The undersize was further sized in trommels to 10 mm and 3 mm. Oversize from the latter was treated in Hartz jigs. The 3 mm undersize was classified in crude hydraulic classifiers furnishing sands to sand jigs, the overflow being dewatered in a long V tank which supplied sands to a Cornish buddle and to Frue vanners. The concentrates were of excellent grade, old records showing assays of 69 pct lead and 29 oz. of silver per ton. Tailings were high inasmuch as the provision for treating the slimes was inadequate. Since the erection of the first mill, the Bunker Hill plant has gone through many changes and improvements. In succeeding years, the flowsheet was enlarged somewhat with Huntington and Chilean mills, vanners, tables, ball mills, and flotation cells being progressively added. In the transition period to the present day practice, the object was not only to improve the equipment for better mechanical performance, but to add new equipment whenever practicable so as to improve both grade and recovery of the product at a lower cost. For the modern plant and flow-sheet, see Figs. 1 and 2. The history of flotation at Bunker Hill dates back to 1913 when experimental work was done in a cell in which the pulp was circulated through a centrifugal pump set outside the cell and discharged against a baffle in the cell. The cell was built with a spitzkasten, and the quiet zone in the latter tended to let the froth break down before it got to the overflow weir. To remedy this situation, a belt drag with light metal flights was arranged for drawing off the froth over a ramp in each cell. Recovery of lead was not as high as present day practice, but was so much better than the vanners that the cells were multiplied gradually to eight cell units. The mill men called them mud hens. Flow between the cells was controlled by a weir, which determined the pulp level in each cell. These early machines were called Bunker Hill machines. The tailings were later treated in pneumatic scavenger flotation machines in a series, producing concentrates for retreatment in the Bunker Hill cleaners as well as the final tailings. This system of flotation served with minor changes until the Fahrenwald machine was developed at Bunker Hill during the period from 1921 to 1925. In 1925, the Fahrenwald flotation machine gradually replaced the Bunker Hill machine, although the Hearing pneumatic scavengers for retreatment of the tailings from the Fahrenwald machines were retained in the lead section until 1928. The use of the Hearing pneumatic machine for cleaning the rougher concentrates was begun in 1924. In 1941, plans were made for remodeling and modernizing the concentrator, the goal being a modern concentrator employing the latest equipment and milling practices. The old wooden building was to be replaced by a steel and concrete structure. Shortly after preliminary work got under way, the United States entered World War II and the demands for metals increased. To meet this requirement, the management decided to increase the capacity of the concentrator to 1800 tpd. This was accomplished in record time by the construction and operation of a sink-float plant. Installation of this plant was the first step in the general plan for modernization. In 1947 the concentrator (including the sink-float plant) was enlarged to handle 3000 tpd. Milling operations today are at the rate of 2300 tpd, five days per week. During 1959, 453,000 tons of ore was beneficiated. The Bunker Hill concentrator is in three sections: the crushing plant, a 3000-ton capacity storage bin, and the concentrator building. The crushing plant is of wood design with a gunnite coating on the exterior.

Jan 1, 1961

By D. A. Elgillani, M. C. Fuerstenau

With either sulfonate or oleate as collector, quartz responds to flotation with moderate additions of calcium only at moderately high pH, where some portion of the activator has hydrolyzed to caOH+ . Calculations of the concentrations of various ionic and precipitated species of calcium and collectors suggest that the products of [(CaOH+) (RSO3)] and [(CaOH+)(01-)] determine whether flotation is obtained under specific conditions. Ion products on the order of 10-12 were calculated for both the sulfonate and oleate systems. The activating effect of calcium ion in nonmetallic flotation systems is of considerable interest because of the normal presence of calcium in natural water. As a result, this phenomenon has received quite some attention in the past. Kraeber and Boppel1 showed that quartz could be activated by calcium above pH 10 with sulfonate as collector. The feasibility of selectively separating quartz from hematite with calcium activation at relatively high pH was demonstrated by Clemmer, Clemmons, Rampacek, Williams, and stacy.2 Cooke and Digre3 showed with a bubble pick-up method that the minimum quantity of calcium ion required as activator for complete pick-up of particles occurs at pH 11.5 for an addition of 20 mg per liter sodium oleate. They also showed that larger additions of calcium (10-fold increase per unit decrease of pH) must be added for complete bubble pick-up as the pH is reduced. Schuhmann and Prakash,4 using a vacuum flotation technique, found that quartz could be floated with moderate additions of calcium chloride and oleic acid at neutral pH, providing the metal ion was present in stoichiometric excess over the quantity needed to form the normal soap with oleic acid. They also reported that calcium will function as an activator only in basic media. More recently, Eigeles and volova5 have shown that essentially complete flotation of quartz is obtained with 6 x 10-4 mole per liter calcium chloride and 1.7 x 10-5 mole per liter sodium oleate at pH 11.6. while no flotation is obtained at about pH 10.9 and below. The importance of adsorption of activator and collector at the air-liquid interface is also demonstrated in these systems. The important role that metal ion hydrolysis assumes in quartz activation systems was also demonstrated recently.6-8 A detailed investigation of metal activation in sulfonate flotation of quartz was undertaken in one system7 and yielded a number of interesting and important observations. Quantification of the data of this system7 to the extent desired was not possible, though, because certain species could neither be ignored nor accounted for accurately. These difficulties can be circumvented when calcium is involved as activator. This detailed analysis was undertaken to obtain a more quantitative explanation of calcium and metal ion activation in quartz flotation. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate9 mol wt 450, and pure potassium oleate were used as collectors. All other reagents used were reagent grade in quality, i.e., n-amyl alcohol as frother, KOH for pH adjustment, and calcium chloride. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. The experimental equipment and procedure were the same as that described previously.6,10 EXPERIMENTAL RESULTS As the presence of precipitates was noted in all of the systems to which ca++ and collector were added, experiments were undertaken to determine the solubility products of calcium sulfonate and calcium oleate using a nephelometer. With this technique, collector is titrated into a known solution, which in this case was 5 x 10-5 mole per liter CaCl2 at pH 5.5. Upon precipitation of the calcium-col lector salt, e.g., calcium oleate, light is scattered and detected

Jan 1, 1967

By R. L. Bleifuss

Most pellets swell only slightly during reduction, but some swell so enormusly that their increase in size is termed catastrophic. Since catastrophic swelling produces irregularities in blast furnace operation, an understanding of the phenomenon is of practical as well as theoretical interest. Observations have shown that catastrophic swelling is characterized by the growth of a network of fine iron filaments. Evidence is presented to show that the growth of these filaments is promoted by the presence of calcium in the magnetite lattice of the original ore. During reduction, the limited mutual solubility of CaO and FeO produces an unstable condition that inhibits the uniform nucleation of metallic iron. Other elements in the magnetite lattice whose oxides are continuously soluble in FeO in the critical temperature range have no effect. Magmatic segregation or pyrometasomatic replacements are the most likely deposits to contain calciferous magnetite. Over the past few years there has been an increasing concern throughout the iron and steel industry over the tendency of pellets to swell during reduction. Although the tendency for swelling is only one of several attributes that determine the behavior of pellets in the blast furnace, swelling-reduction tests are now part of the normal evaluation procedure of many pellet consumers. During a swelling-reduction test, pellets display either the moderate increase in size known as normal swelling, or the enormous expansion known as catastrophic swelling. This paper is concerned with the origin and control of catastrophic swelling and how it is enhanced or inhibited by the presence of minor elements. Swelling Behavior The swelling behavior of pellets during reduction is indicated in Fig. 1. The lower curve represents normal swelling and the upper curve catastrophic swelling.' During the initial stages of reduction, that is, up to about 20-25% reduction, the two curves are considered to be equivalent. Beyond this point normal pellets undergo a gradual decrease in size with increased reduction. By contrast, pellets which exhibit catastrophic swelling show a second dramatic expansion between 25 and 70% reduction. The initial normal swelling develops as the hematite of the pellet is successively reduced to magnetite, and then to wustite. Work by Edstrom' and others has shown that the reduction of hematite to magnetite is accompanied by a 25% volume increase, whereas the magnetite to wustite stage shows a volume decrease. The volume increase overlaps the wustite field because magnetite is formed simultaneously with the wustite during topochemical reduction of the pellet. The catastrophic expansion is clearly related to the wustite, to

Jan 1, 1971

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

An analytical method has been developed and used in batch and continuous tests to provide initial insights into the effect of soluble calcium ion in anionic flotation of silica from iron ores. A deficiency or excess of calcium ion in pulps subjected to this type of flotation produces an impairment in flotation efficiency. Data developed in the investigation are from a single ore, but show that total calcium requirement is met from water, ore and reagent sources. In batch studies, starch additions were shown to exert no influence on the calcium level, but fatty acid and sodium hydroxide had subtractive effects. The investigation was next extended to continuous flotation testing where the general observations from batch testing were confirmed. Factorially designed experiments were performed showing that the relationship of calcium additions to flotation response was not a simple one, but tended to shift to higher additions with increased fatty acid. Nevertheless, the range of soluble calcium levels measured remained fairly constant in areas of good flotation response. It is concluded that techniques developed should be useful in removing empiricism from flotation operations in this and other systems requiring activation for success. Further development should aid in process control both through methods outlined and through investigations aimed at studying the effects of other soluble reagents. Of the major mineral commodities, iron ore was one of the last to succumb to flotation processing. Commenting on this fact, one of the speakers 1 at the convention celebrating the 50th Anniversary of flotation in the U.S.A., said ". . . in 1951 froth flotation as a means of beneficiating nonferrous minerals was a might giant and could be characterized by 'you name it, we float' - but not iron ore". This tardiness in applying flotation to iron ores was the result of a number of factors, including economics and ready availability of direct shipping ores. Even now, when the need for beneficiation can no longer be denied, proposals for flotation of iron ores are apt to be viewed with some misgivings. This disquiet results from knowledge that wide variability, which would necessitate corresponding adjustments in reagents, often exist within even a single ore deposit. Coupled with ore variability is the fact that, at present, there is no way of quickly and precisely anticipating the direction and magnitude of reagent changes required for uninterrupted production of acceptable concentrates. Despite the long delay, iron ore flotation is now practiced commercially, although the chief applications2-4 are to specular hematites having relatively coarse liberation and low slime content. In addition, the application of flotation in upgrading magnetic concentrates seems assured. However, these flotation methods do not appear applicable to substantial tonnages of fine grained, earthy, and frequently more complex semitaconites and nonmagnetic taconites. The U.S. Bureau of Mines, in devoting its attention to the semitaconite and nonmagnetic taconite class of materials, has demonstrated that anionic flotation of calcium-activated silica can be utilized with an expected high frequency of success.' Even so, it has been recognized that the flotation method is a complex one, and that the reagent suite must be carefully tailored to the feed. These conditions would be expected to offer difficulties in treating ores with the wide range of variability previously discussed. Accordingly, research was initiated to develop methods to remove much of the empiricism from the flotation operation by measuring the reagent variables within the pulp for a correlation with flotation response. A simple illustration of the technique sought would be in the well established use of pH meters to provide feedback control to reagent feeders and thereby limit acidity or alkalinity to a range producing optimum results. The first efforts in this area have been concerned with measurements of soluble calcium ion. Bureau experience in both laboratory and pilot plant over the past five years has proved that the amount of calcium

Jan 1, 1965

By T. D. Tiemann

The caustic extraction of silica from Wisconsin and Minnesota taconite was investigated by bomb digestion over the temperature range from 312 to 40S°F at caustic concentrations from 25 to 500 gpl. Residual concentrates containing as much as 65 pct iron were obtained. The high rate of silica extraction is related to a microcrystalline variety of quartz, since it is shown that the rate of extraction of silica from quartz is directly proportional to its surface area. Increasing dependence on foreign ore reserves makes the need for developing the technology necessary for treatment of our low grade ores even greater than it was at the time of World War 11, when much research was conducted on the extraction of alumina from clays. Representative of these were the studies carried on at the University of Illinois.' More recently, the U. S. Bureau of Mines investigated the production of alumina from anorthosite, and currently the aluminum industry is showing renewed research interest in this field. The studies reported here are part of a continuing research program based on the above concepts and aimed at the eventual development of processes for the treatment of low grade ores, particularly those of iron. The fact that large reserves 3 of low grade nonmagnetic taconite are contained in the iron formation of the Wisconsin Gogebic range have made this ore an important and attractive target for investigation. The idea of removing silica by caustic extraction is not new.495 The digestion in caustic solution of ground flint, diatomite, and other forms of chalcedonic silica is the basis for the production of soluble sodium silicates by the wet-process. Upgrading bauxites by the caustic extraction of silica has been investigated6 and is the subject of a German patent.7 Although mention is made by Roe' of the caustic extraction of silica from low grade Michigan and Wisconsin iron ores, and he lists a number of patents and references on the subject, recent work in the field does not appear to be extensive. As far as the author knows, there has been no work in this field on these particular ores. It is hoped that this paper will stimulate further investigation which will eventually lead to an econclmic means of processing these large low grade reserbes. TACONITES The taconites investigated in this study were from Minnesota and Wisconsin. That from Minnesota, a semi-taconite, Nas obtained from the Oliver Iron Mining Division, U. S. Steel Corporation, and represents a sample of an oxidized iron formation from their King Mine on the Mesabi range. The Wisconsin taconite came originally from the trench sampling of the U. S. Bureau of Mines, and represents a composite of the Norrie, Pabst, Yale, Plymouth, and Pence members of the Gogebic iron formation. Assays on these samples are given in Table I. A typical calcu1atr:d average analysis of the Wisconsin taconite is given in Table 11. Chemically, the Minnesota semi-taconite sample contains about 39 pct iron and 39 pct silica, while the Wisconsin taconite contains 30 pct iron and 53 pct silica, both on the dry basis.

Jan 1, 1962

By James E. Lawver, James L. Wright

This paper describes the design of a cell used to measure the electrical conductivity, or the reciprocal resistivity, of granular materials. It also establishes a quantitative relationship between the electrical conductivity and the electrical separation of selected mineral samples. It is estimated' that the free world produces about 13 million tons of mineral concentrates a year by electrostatic or electrodynamic methods. At least 95% of these concentrates are produced by corona discharge type machines that separate minerals by exploiting the differences in their electrical conductivity. But, what is meant by the electrical conductivity of a mineral? How large a difference in the electrical conductivity of two mineral species is necessary to effect a separation? Just what is the role of conductivity in electrical separations with regard to capacity and selectivity? There is a considerable amount of information in the literature on both the mechanisms of conduction and the values of the electrical conductivity of pure single-crystal mineral specimens. In addition, some insight into the role of mineral conductivity can be obtained by referring to a Bureau of Mines publication' in which 95 minerals have been grouped as conductors or insulators as a function of temperature. The classification was made on the basis of the percent of weight that reported as "conductors" in an electrical separator. But, as is often the case in the mineral industry, practical application leads theory — and there is little useful information in the literature giving any kind of quantitative relationship between electrical conductivity and electrical separations. The problem is a bit complex because electrical conductivity per se — which can be rather easily measured on large, single grains — is not sufficiently informative to permit quantitative predictions of the separability of the mineral system. Practical "high-tension"* separations are made at such feed rates that the band of minerals on the rotor is multilayered in thickness. Thus, the effective conductivities of minerals as seen by a high-tension machine include particle-to-particle contact resistance, which is often a controlling factor in making a separation. This is particularly true when the mineral grains are coated with slime or with a dielectric surface film. From a high-tension separation viewpoint, one is actually concerned with the time required for corona-charged grains to lose enough charge so that the centrifugal force acting on the particles exceeds the image force holding the grains to the rotor. This calculation requires a knowledge of the effective mineral conductivity s. (The conductivity of the metal rotor is sufficiently greater than that of the minerals so that it need not be considered in charge decay calculations.) The charge density at time t can be approximated by the relaxation equation.3 where t 5 charge density at time t r, - charge density when t = 0 cr e total electrical conductivity £ = permittivity The time required for the charge density to fall to l/e of its initial value is called the relaxation time and is numerically equal to €/n. AS defined here, u is the conductivity of an element of homogeneous grains making contact with each other and with a grounded rotor. This paper deals with the design of a conductivity cell used to measure a, or its reciprocal p, the electrical resistivity. CELL DESIGN Initial test work was performed with a cell recommended by ASTM.4 Since the reproducibility with the ASTM cell was not satisfactory, it was decided to

Jan 1, 1970

By L. J. Boucher

The beneficiation process at Northampton is described and reasons are given for installing a flotation plant. The economics of running the plant, the difficulties of operation, and subsequent remedial action are discussed. CEMENT rock from a quarry operated by the Northampton plant1, 2 of the Universal Atlas Cement Co. has a relatively low average CaCO³ content. To meet specifications required for cement manufacture it was formerly necessary, over succeeding years, to add increasingly larger amounts of high-lime, low-alumina rock, which was obtained from a quarry operated by the company at a point along the New Jersey-New York state border, 79 miles from Northampton. Previous to 1940, 8 pct of total kiln feed consisted of high-lime rock. From 1940 to 1943, this figure jumped to 13 pct. Today it would be necessary to use 18 pct of this high-lime to meet current specifications. Increasing transportation costs made this an expensive operation. In addition, this high-lime rock quarry was contaminated with granite and high magnesia pockets. As there was no available high-lime rock in the Lehigh Valley, it was decided in 1936 to install a pilot plant where experimental work was done on processing local cement rock with flotation and burning the resulting product in a small kiln. This plant was in operation for six months and at the end of that period a suitable method of flotation had been established. From these studies it was also found that if the proportion of shipped-in rock rose slightly above 10 pct it became economically advisable to use the flotation process. It is the object of this paper to present briefly the operation of the flotation system at the Northampton plant. It seems advisable to comment on the raw material used in this process. The Northampton quarry lies geologically in what is known as the Jacksonburg formation of Trenton limestone.' In Pennsylvania this extends in a southwesterly direction from Portland, through Nazareth, Bath, and Northampton and across the Lehigh River to Ormrod. This argillaceous limestone was formed from marine deposits laid down during the early Ordivician period when a shallow sea covered most of Pennsylvania. Carbonaceous matter in the original deposit formed graphitic carbon under later metamorphic forces. From this graphite the cement rock of the Lehigh Valley derives its dark color. Most of the graphite must be removed before lime flotation can proceed. The quartz in this rock is desirable from the chemist's point of view, as it furnishes him with a form of silica necessary in the calcining process, but its abrasive properties damage pumps and piping. Aluminum silicates of potassium, sodium, iron, and magnesium are found in the form of sericite. Cal-cite averages from 69 to 76 pct. Iron in the form of iron pyrites is also present and has no deleterious effect. Talc is present in minute quantities. The

Jan 1, 1954