Search Documents

By J Addai-Mensah, W Skinner, C Kelsey, J R. Kelly, E Baawuah

Comminution continues to be the most capital-intensive unit operation in mineral processing. The fundamental purpose of comminution is to liberate the valuable minerals so that they can be economically concentrated into saleable products. Declining ore quality characterised by lower grade and increased complexity requires significant energy consumption for comminution. Low-grade magnetite ores are typically fine-grained and require fine to ultra-fine grinding (P80 ~ 30 - 40 µm) to enhance its liberation from the typically siliceous gangue matrix. Historically, this has been achieved using multi-stage crushing and grinding technologies, which require high energy consumption with low energy efficiency. This motivated innovations in energy efficient technologies for comminution. Such technology has been developed in the IMPTEC super-fine crusher. It is an innovative, dry (with the potential to be operated wet), media-free, energy efficient crusher that can to reduce 10 mm feed particles to 19 – 30 µm with very low recycle loads. In this study, the mineralogical and physicochemical characteristics of crushed magnetite ore using the IMPTEC super-fine crusher have been investigated in comparison with those of rod milling. The super-fine crusher generated higher liberated magnetite minerals in the – 300 + 212 µm and < 45 µm size fractions compared to rod mill. Both comminution devices generated large low-grade hematite and goethite middlings. However, the rod mill produced higher locked/unliberated hematite and goethite compared to that of the super-fine crusher. Quartz mineral had the highest liberation irrespective of the comminution device used. The super-fine crusher generated higher entrapment of other minerals within the silica matrix compared to the rod mill. The breakage mechanism of the super-fine crusher which is predominantly through high compression with shear, generated improved mineral liberation in the coarse size fractions compared to the predominant abrasion and attrition breakage mechanisms of rod milling. The higher mineral liberation generated by the rod mill is potentially due to the prolonged batch milling of the ore compared to the single-pass open circuit of the super-fine crusher.CITATION:Baawuah, E, Kelsey, C, Kelly, J R, Addai-Mensah, J and Skinner, W, 2018. Mineral liberation studies of IMPTEC super-fine crusher – 130 crushed product, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 313–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Timothy J. Napier-Munn, David M. Weedon

A model of mineral liberation was developed using back calculation techniques to determine breakage/liberation parameters in a similar manner to the way breakage parameters are determined in the Population Balance Model (PBM). Comminution and liberation data was collected from grinding mills operating at Pasminco lead/zinc mine Broken Hill, and Mt. Isa Mines copper concentrator, Mt Isa, Australia. Laboratory scale single particle breakage tests on ore samples from these sites were undertaken using a twin pendulum breakage device. Break- age/liberation parameters were then determined for several mills using back calculation techniques. The liberation/breakage parameters were then used to simulate mill liberation performance under varying conditions.

Jan 1, 1996

By M Thomas, M Caccetta, C Laukamp, A Hacket, M Jones, A Rodger, M Verrall, R Hewson

A mineral systems approach was used to interpret precompetitive airborne mineral mapping geoscience data for iron oxide copper gold (IOCG) exploration in the Starra area, Eastern Succession, Mount Isa Inlier. Selected minerals were chosen to map possible source rocks/fluids as well as intersecting structural/fluid pathways that could have transported mineralising fluids into domains of contrasting rocks/fluids where there was potential for physicochemical gradients to precipitate metals. Ferric and ferrous iron contents and white mica abundance were useful mineral criteria to identify theMount Dore Granite of theWilliams-Naraku Batholith as a potential source of æoxidisedÆ fluids rich in Fe, K and potentially Cu-Au. The Mount Dore Shear Zone (MDSZ) intersects the western margin of this granite with the highest contents and changes in composition of the white mica are peripheral to this contact within the granite. This together, with the fact that the entire N-S length of the MDSZ in the study area (~16 km) is abundant in white mica are evidence of K-rich fluids had preferentially moved along this pathway. To the south, the MDSZ intersects a domain comprising massive ironstone bodies as well as numerous graphitic horizons. This interpreted æreducedÆ domain is well mapped using the æopaqueÆ mineral products, as well as by white mica, which is pervasively developed and extends 2 km either side of the MDSZ fault into the meta-sedimentary sequences. The chemistry of this white mica also changes progressively away from the MDSZ, becoming more Si-rich (longer wavelength) towards the contact with massive ironstone bodies in the west and the graphitic units in the east, both of which represent sites of known Cu-Au mineralisation. Beyond these contact zones of interpreted æoxidised fluidsÆ with reduced rocks/fluids, there is either a rapid change to Si-poor white mica and/or no white mica developed, ie major æchemicalÆ gradient change. These mineral mapping results provide evidence for a direct link between possible source rocks and sites of IOCG metal deposition as well as extending the associated alteration zonation which had previously been mapped/published at the metre-scale to the kilometre-scale. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The mineral matter has been isolated from a selection of Australian bituminous coals using low temperature (radio-frequency) oxidation or hydrogen peroxidation techniques and the species present identified by x-raydiffraction. Quartz, kaolinite, and a range of mixed layer clay minerals are the dominant constituents of the coals studied, with carbonate, sulphate, and phosphate minerals abundant in some samples. The clay bands thatoccur within these coal seams contain similar mineral assemblages to the coals themselves, but the lutites that form the inter-seam strata have a markedly different mineralogy, characterized by abundant quartz andillite and a low kaolinite content.The kaolinite is thought to have formed chiefly by interaction of silica and alumina in the waters of the coal swamp, aided by the catalytic action of organic acids, while most of the other clay minerals are probablydetrital. The absence of illite from Australian coals is not fully understood, but it may reflect the action of organic acids on the detritus in the swamp, coupled with deposition in freshwater rather thanmarine conditions. Pyrite, although present in some coal samples when fresh, may undergo oxidation during storage to form a number of sulphate minerals, some of which may interact with any calcite present toform gypsum.The mineral matter assemblage in the coal determines to a great extent the fusion characteristics of the ash.Unless abundant carbonates are present, coals with kaolinite-rich assemblages have a very refractory ash, while those rich in chlorite or montmorillonite have ash fusion temperatures between 1000 and 1300°C. Theinfluence of the minerals on coal preparation and coking properties is also brieflY discussed, as well as the potential of mineral matter studies in coal seam correlation.

Jan 1, 1978

By Frank R. Field, Joel Clark, Walter C. Labys, William A. Vogely

Mineral models provide a systematic and comprehensive approach for analyzing and fore- casting the behavior of mineral markets and industries.' They also permit the analysis of a wide range of policy decisions. Obviously such models cannot capture all of the intricate relationships that shape the behavior of a mineral market. However, such models have become extremely useful and in many cases support the decision making approach of judgmental analysts. They tend to narrow the range of likely outcomes and thus reduce the risks and uncertainties of investing, trading, and speculating in minerals. Mineral models provide not only answers to "what-if" questions, they also inform analysts of the benefits and costs associated with mineral investment decisions. More recently they have been applied to specific mineral issues of the possible impact of buffer stock stabilization schemes and of import supply restrictions. Mineral Models Defined Because mineral models are so diverse, we must begin with a fairly broad definition. A mineral model is a formal representation of a mineral market, industry or system where the behavioral relationships included reflect the underlying economic and engineering factors as well as the political and social institutions. Of ten, but not always, a mineral model will consist of some combination of the following components: demand, supply, inventories and prices. Modeling of demand behavior normally begins with an interpretation of basic demand responses to prices and income (i.e., the associated price and income elasticities). Price elasticities vary among different minerals and among their diverse uses. They tend to be lower for minerals without close substitutes than for those where such substitutes exist. In addition, these elasticities vary with time as well as with the actual excess demand or excess supply. Variations like these, coupled with the relative instability of prices for a number of minerals, make explanations of demand behavior difficult. The degree to which demand responds to changes in income depends on the income elasticity of the end products to which the minerals serve as inputs. Those products with a relatively low income elasticity tend to experience proportionally smaller swings in sales than those with higher elasticities. The transmission of demand cycles to minerals producers comes through a series of stage-of-process effects. Demand measurement also is influenced considerably by mineral substitution patterns. The cross-price elasticity of a competitive or complementary commodity also varies with minerals, markets, and time. Where minerals easily substitute for one another, as in the case of cop- per and aluminum in electrical conductor applications, cross-price elasticities are relatively high. Modeling of mineral supply behavior normally involves consideration of resource development, economic conditions, geologic

Jan 1, 1985

By JOHN R. SUMAN

IT appears now that the conflict with the totalitarian states will be a long-drawn-out struggle. The course of this war up to now indicates that this may well be the first major conflict where man power has not been the vital and determining factor. Mechanized warfare has made it possible for relatively small, well-equipped groups to outmaneuver and defeat large armies which lack the necessary modern equipment. Under these circumstances, ultimate victory becomes a matter of resources and productive ability. The important question is not how many soldiers can he put into the field, but the volume and speed in producing the armaments essential to ensure a victory. The resources available to the opposing nations and the efficiency of their systems of enterprise and production will be primary factors in determining the ultimate outcome. Germany had a head start of eight years in the armament race, and it is not easy to overcome such an advantage overnight.

Jan 1, 1942

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector's item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy's slate left most classrooms before the oldest of us were born.

Jan 9, 1964

By J. Groff

The Getchell and Twin Creeks mines are located along a north-northeast trending structural zone in Humboldt county, Nevada approximately 40 miles northeast of the town of Winnemucca. Gold mineralization at the Getchell mine is represented principally by sulfide-rich ores, which contain significant amounts of realgar and\ orpiment, with the gold being recovered through processes which involve pressure oxidation. In contrast, oxide ores are currently being mined and processed at the Twin Creeks mine although large reserves of sulfide ores, some of which contain orpiment-realgar-stibnite, have been defined (Bloomstein et al., 1990). The Getchell and Twin Creeks mines represent major gold orebodies but very little has been published pertaining to mineral paragenesis and the characteristics of ore-forming fluids for these deposits.

Jan 1, 1994

By R. M. Beauchamp

Base metal processing operations often treat process tailings and acid mine drainage using a high density sludge (HDS) water treatment process. Lime is used in this process, which reacts with existing sulfates to form gypsum. When a recycle stream is incorporated in the process, gypsum levels in recirculating water may build up and cause high levels of gypsum supersaturation. Precipitation of gypsum from the supersaturated process water causes many problems. It is speculated that gypsum may precipitate on sulfide minerals and silica gangues in the flotation circuit, resulting in decreased selectivity and recovery. An understanding of the determinants and nature of precipitation may provide solutions to mitigate the formation of precipitates and improve flotation performance. This study showed that both sphalerite and silica exhibited gypsum- or calcium carbonate-like behavior in the respective supersaturated solutions, indicative of a coating of calcium species on the mineral particle surfaces. The addition of copper sulfate and/or potassium xanthate had little effect on the precipitation of gypsum or calcium carbonate on the mineral particles. Sodium carbonate is encouraging as a method to minimize calcium species interactions on sphalerite/silica surfaces.

Jan 1, 2006

By L. A. Neumeier

The Bureau of Mines, U.S. Department of the Interior, is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide .phases by sulfldation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes initial research involving sulfidation partitioning of chalcopyrite concentrates. Small chalcopyrite samples were sulfidized with elemental sulfur in glass capsules sealed after evacuating and backfilling with helium, by heating for 1 to 24 h at specific temperatures in the range of 250° to 500° C. which extends from below to above the boiling point of sulfur (-445° C). Above the boiling point of sulfur, the overall reaction with adequate sulfur (13.9 wt pct of CuFeS2) is 5CuFeS2 + 4S g ? Cu5FeS6 + 4FeS2.

Jan 1, 1989

By L Lagoeiro

The samples studied in this paper were derived from the iron oxide facies of iron formations (IFs) of the Quadrilßtero Ferrffero, south-eastern Brazil. The rich-iron oxide varieties of the IFs can be regarded as Fe-O systems because they consist predominantly of aggregates of haematite and magnetite crystals. The study was based on carefully selected samples in which magnetite crystals occur as isolated large crystals set in a matrix of haematite grains. Optical microscopy and an electron microscope equipped with an electron backscattered diffraction (EBSD) system were used to investigate the microstructural and crystallographic relationships involved in the phase transformation between magnetite and haematite. The magnetite crystals in the IF samples are partially transformed to haematite and this process is also known as martitisation. This transformation occurs along the crystallographic planes {111} of the magnetite producing a characteristic triangular pattern of interlocking lamellae of transformed haematite crystals that are oriented parallel to octahedral plane {111}. This new generation of haematite is referred to martite because of the martitisation process. EBSD analyses show that the magnetite and the new haematite crystals, martite, share crystallographic planes of highest atomic density, eg {111} and (0001), respectively, possibly due to the ccp and hcp atomic arrangement of the two crystals. Stereographic projections of these two planes therefore coincide when the maxima of their poles are plotted. However, the crystallographic orientation of the haematite crystals in the matrix shows maxima of (0001) poles that do not coincide with those of {111} planes of magnetite. Consequently, it is concluded that the direct transformation to haematite crystals retains the crystallographic orientation memory of the former magnetite crystals, possibly due to the similar manner whereby their atoms are packed together in the crystal structures. On the other hand, no such relationships are observed between magnetite and haematite crystal in matrix. This suggests that haematite grains in the matrix may have been formed by other processes rather than those involved in the iron oxide transformation observed within the magnetite grains.

Jan 1, 2008

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Pavel Mikhailik

INTRODUCTION Ferromanganese (FeMn) crusts from Mendeleev Ridge, Chukchi Borderland, and Alpha Ridge, in the Amerasia Basin, Arctic Ocean, are similar based on morphology and chemical composition. The crusts are characterized by two- to four-layered stratigraphy. The chemical composition of the Arctic crusts differs significantly from hydrogenetic crusts from the North Pacific Prime Zone (PCZ; Hein et al., 2013), such as a high mean Fe/Mn ratio (2.6 versus 1.3) and low Si/Al ratio (1.8 versus 4.0), with lower Mn, Ca, Ti, P, Ba, Co, Cu, Ni, Pb, Sr, and Zn and higher Si, Al, Mg, As, Li, V, Sc, and Th. Based on Arctic FeMn crust mineralogy, chemical composition, and growth rates, crust formation was dominated by three processes: Precipitation of Fe-Mn (oxyhydr)oxides from ambient ocean water, sorption of metals by the Fe and Mn phases, and fluctuating but large inputs of terrigenous debris (Konstantinova et al., 2017; Hein et al., 2017). The Mn and Fe phases are hydrogenous and reflect bottom ocean-water chemistry and the aluminosilicate phase contains stable detrital minerals such as quartz, feldspars, zircon, monazite, and clay minerals. A precise method of studying the distribution of elements in FeMn crust phases is sequential leaching that dissolves four mineral phases of different stability step-by-step, in the following order: easily leachable phase, mostly bio-calcite; manganese oxides; iron oxyhydroxides; and residual aluminosilicate minerals (Koschinsky and Halbach, 1995). Twelve bulk crusts and crust layer samples obtained from six hydrogenous FeMn crusts were studied. Those crusts were collected during Russian (Arktika 2012) and USA (HLY0805, HLY0905, and HLY1202) research cruises from different parts of the Amerasia Basin (Mendeleev and Alpha Ridges, Chukchi Borderland). Samples were chosen for the sequential leaching experiments based on their morphology, location, and water depth. Hydrogenetic crust (D07-33) from the Tuvalu EEZ, central-west Pacific Ocean, was included in the experiment for comparison. Recovery during the four-step sequential leaching, with respect to the bulk analyses, was between 80% and 120%.

Jan 1, 2018

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after it has been pulverized to pigmentary size. The current world production of iron oxide pig¬ments is estimated by the author to be between 450,000 and 550,000 tons based on 1969 data. The fact that highly colored natural deposits of iron ore are found throughout the world ac¬counts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments pro¬duced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970). Nomenclature With the increasing importance of the syn¬thetic iron oxides it is necessary to make a distinction between the natural or mineral pig¬ments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a com¬mercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pig¬ments. Natural pigment ore sources are se¬lected for their special physical-chemical prop¬erties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pig¬mentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1975

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The current world production of iron oxide pigments is estimated by the author to be between 499 and 590 kt (550,000 and 650,000 st) based on 1979 data. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970) and increasing to $97 million by 1980 (Spinrad, 1980). Nomenclature With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments. Classification An important characteristic of a pigment is its color and, therefore, a logical separation can be made on this basis. A. Yellow Iron Oxide Pigments 1. Natural mineral origin a) Goethite b) Lepidocrocite c) Ochres d) Siennas e) Limonite 2. Synthetic pigments a) Goethite B. Red Iron Oxide Pigments 1. Natural mineral origin a) Hematite b) Siderite (calcined) c) Pyrites (calcined) 2. Synthetic pigments a) Hematite C. Brown Iron Oxide Pigments 1. Natural mineral origin a) Umbers b) Limonite (calcined) c) Siderite (calcined) d) Goethite (bog ore or sulfur mud) 2. Synthetic pigments a) Blends of hematite, goethite, and magnetite

Jan 1, 1983

By Charles L. Harness

MINERAL pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and Limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, such as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-Limonite (2Fe203.H20 to Fe203.4H20), hematite (Fe203), or magnetite (Fe203.FeO). Man's first permanent coloring materials were earth pigments- the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands

Jan 1, 1949

By Kenneth R. Hancock

The importance of "Mineral Pigments" can best be shown by noting that the world production is estimated to be in excess of 47 billion kilograms (52 million st). This quantity if pack- aged in the common 22.6 Kg (50 Lb.) bag and placed end to end would circle the world over 500 times. This world production figure is based on a broad concept that pigments, extenders, and fillers have essentially similar functions. In this paper mineral pigments are products produced synthetically or from selected minerals and through pulverization have characteristics of pigments.

Jan 1, 1985

By Anthony Leddin, Gillian Dooley

This paper is concerned with mineral policy in Ireland and how it might be improved to encourage more exploration and investment in mining in the country. The approach is to first outline the main desirable characteristics of a comprehensive national mineral policy document. This aspirational document is then used to assess the current regulatory, legislative and fiscal frameworks for mining in Ireland. The analysis also contains a brief account of the history, structure and characteristics of the mining industry in Ireland. The main focus of the paper is to identify those aspects of the existing framework that erode Ireland’s attractiveness to mineral investment and to suggest policy improvements.

Jan 1, 2005

By L. O. Thomas

BROADLY, Yukon is divisible into three physiographic provinces which are extensions of the similar divisions in British Columbia that are there known as the Coastal system, the Interior system, and the Rocky Mountain system. South of Yukon to about the 50th parallel of latitude, the Coastal system consists solely of the Coast range, which, in Yukon, passes behind the St. Elias range and for the remainder of its course constitutes the most easterly portion of the Coastal system. The extension, in Yukon, of the Interior system of plateaus and mountains of British Columbia is commonly referred to as the Yukon plateau, and the extension of the Rocky Mountain system as the Mackenzie Mountains system. The Coast-Range province is largely made up of granitic intrusives; the Mackenzie Mountains province of folded sediments; and the intervening Yukon Plateau province of ancient metamorphic rocks, folded sedimentary rocks, volcanics, and intrusives. Almost the entire area dealt with in this article was subjected to glaciation and, in those parts where its full effect was experienced, the valleys were invaded by vast masses of ice which transported and scattered the stream gravels, with their gold content, so that, even where gold still remains in the old stream channels, it has become so buried under boulder clay and other glacial accumulations that it is, in most places, difficult to find, and, when found, may prove very expensive to mine. Most of the present rivers have done little more than cut new channels in the glacial debris, touching only here and there upon the subjacent rocky floor. The territory in Yukon adjacent to the section of the Alaska highway between Watson and Teslin lakes is for the most part unknown both topographically and geologically. From Teslin to Kluane, the highway travels a fairly well-mapped part of Yukon, but beyond that point, until White river is reached, the geology of the adjacent country has, largely, yet to be determined, particularly on the north side of the highway.

Jan 1, 1943

By L. O. Thomas

THE Alaska Highway, in its course through British Columbia, traverses parts of two great physiographic divisions of Canada which are also distinctive geologically-the Cordillera in the western section and the Interior Plains in the eastern. The Cordilleran region in the portion of the Province with which this paper deals can be divided into four major northwest systems, known respectively from west to east as Coastal, Plateau, Cassiar-Omineca, and Rocky Mountains. The Coastal system consists solely of the Coast range except in the extreme northwest, where a part of the St. Elias range is included. The Coast range, characterized by mountains of great ruggedness,. is made up of an igneous complex of granitic rocks intruded chiefly as a great batholith. In places, spurs of these rocks extend into the Plateau heft, a partly mountainous tract largely occupied by quartzites, quartzose mica schists and their gneissic phases, and crystalline limestone with interbands and broad areas of chlorite, _hornblende, and sericite schists and bodies of intrusive granite gneiss-an assemblage of rocks known as the Yukon group. The Cassiar-Omineca system marks the divide between the Pacific and Arctic drainages. Its eastern boundary is well defined in the south by the Rocky Mountain Trench (see p. 229). The rocks of the system are, miainly, highly altered Palaeozoic sediments, but there are also Precambrian and Mesozoic rocks, the latter largely volcanic. The core of the system is granitic and there is evidence (see p. 221) to support the belief that it is of such a length as to constitute a batholith comparable to that of the Coastal system.

Jan 1, 1944

By Thomas. L. O.

Apart from a few sketches and incomplete maps, mainly topographical, and one or two detailed maps of placer-creeks, there is little information on the topography and geology of most of the country adjacent to the sections of the Alaska Highway in the Liard River area, particularly that part east of Kechika river. In 1943, the Geological Survey of Canada made a recon-naissance from Fort Nelson clown the river of that name to the Liard, thence up the latter to Hell Gate, and also up Beaver river for a distance of fifty miles. The whole of the area covered was found to be underlain by sedimentary rocks, not a single igneous dyke being seen. The British Columbia Department of Mines began reconnaissances near the highway both in and north of the drainage basin of Prophet and Muskwa rivers with a view to finding structures favourable for the accumulation of oil. In Liard River valley near the mouth of Smith river and at intervals from there clown to Devil' s Portage occur warm springs whose character and origin are not definitely' known, since they have not been investigated (21, p. 38A). Similar springs are said to occur at several localities over a broad belt extending from Muskwa river across the Liard to the Nahanni River country (26, p. 11). On Liard river below the mouth of Dease river, stratified sands, gravels, and clays of Pleistocene (?) age are constantly met with and in one or two places are underlain by sandy clays. The distribution of the latter, however, is very limited in the section cut by the river west of the Rocky mountains. The only range of these mountains that reaches the Liard is the high limestone ridge which approaches the mouth of Vents river from the southeast and then almost vanishes a few miles to the northwest of it (27, pp. 43-45). In general, the ranges of the Rockies in the area under consideration have been but little explored, but they are undoubtedly very largely sedimentary and, with the exception of some volcanics and intrusives on their western flanks, are probably almost entirely so. Unlike the high, deeply incised ranges in southern British Columbia, they dwindle in elevation north of Terminus mountain to low-wooded ridges separated by wide swampy valleys, and practically lose their identity between it and the Liard. The foothills, which, along the Liard, have a width of 38 miles (from near the mouth of Trout river to Hell Gate) are composed of a great series of alternating shales and sandstones, with some limestones, all folded closely together, which resemble those found in the foothills farther south (27, pp. 50, 19-20).

Jan 1, 1944