Search Documents

By Robert E. Kirby

The potash mine and refinery of AMAX Chemical Corporation is located 26 miles east of Carlsbad on the north end of the potash producing areas. This property was developed between 1949-1952 and production of muriate began in August 1952. Two shafts, located 400 feet apart, were sunk to the ore zone 900 feet below the surface. A 15-foot diameter ore hoisting shaft equipped with a 1000-ton ore pocket, crusher and automatic skip loading equipment plus a 20-foot diameter service shaft with a curtain wall for exhausting air were provided. Sylvinite production to date has been from the first ore zone, stratigraphically, the lowest of ten identified mineralized zones in the salt section. This first ore zone has been the top producer of Muriate of Potash over the years. In our area we do have some very marginal mineralization in the third ore zone some 35 feet above the first. We have not mined from this seam as yet but we are investigating the economics very closely with access slopes and an experimental mining panel. Our ore seam is generally flat lying but does have local gentle rolling with grades from 2% to 5%. The mine was designed and developed from the beginning with conventional mining practices and rail haulage from the mining section to the ore pocket. As mining progressed in the early years, production increased from less than one million tons annually to a maximum of 3,935,000 tons in 1964. Efficiency also kept pace with the increasing production and continually improved until the efficiency of the production crews reached an average of 100.3 tons per manshift in 1964.

Jan 1, 1974

By R. L. Grayson, G. Mishra

Introduction Many old underground mines have been developed extensively into reserves requiring large numbers of workers to maintain and rehabilitate lengthy track haulages and/or belt conveyor systems. Often, large numbers of fans are required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. Problems that beset one such coal mine and projects undertaken to restore it to potential profitability are presented. Brief history The Vesta No. 5 mine was opened in 1908. Drift development began near the Monongahela River, which was the primary avenue for shipping metallurgical coal to coke ovens in Pittsburgh. Over the ensuing 75 years, the main haulage entries were developed a distance of 16.1 km (10 miles) to the present mining area. Track haulage was used to transport coal from working sections to the river loading facility. As haulage distance and areas of high water influx increased, management decided, in 1973, to construct an underground conveyor belt system. The project spanned 36 months and culminated in a system of 22 flights, ranging from 205.7 to 1767.8 m (675 to 5800 ft) long. Six intake and eight return entries were developed as the mains were advanced. These entries provided adequate ventilating capacity over the years, but as extensive gob areas progressed and roof conditions deteriorated, the entries became inaccessible and more resistant to airflow. By 1981, five fans were being used to circulate 943.9 m3/s (555.5 cfm) of air through the mine. An average of 6440 t (7100 st) were produced from 20.8 continuous miner unit shifts and 2.7 longwall unit shifts each day in 1981. The ratio of support to production personnel was 1.94. To maintain the outby 16.1 km (10 miles) of haulage, 110 personnel were used. The average cost per ton was $43.54 ($39.58 per st), resulting in excessive bottom-line losses. The mine possessed a rather promising reserve, mostly in lease, of good quality, medium-sulfur metallurgical coal, but it also had a number of formidable operating problems. Operating problems Contributing factors toward relatively low productivity and high costs were the conditions of the track haulage, conveyor, and ventilation systems. Productivity was affected greatly by downtime associated with the conveyor system, which lacked adequate access for making splices or other repairs. Many areas within the conveyor belt entry itself required more

Jan 1, 1988

By L. K. Daneshmend

The mine of the year 2020 will need to be based on a new way of mining. It will employ technology in a paradigm that assumes responsibility for sustainable development: taking account not only economic but also ecological and social issues. This will require a holistic approach to mine design and planning, considering all controlling factors and impacts (technical, economic, environmental and social). A national collaborative strategy is required to address the several options that exist for the development and application of 2020 mining technology. Key issues in implementing 2020 mining technology will also relate to human resources, in terms of employment, skills and education. A need exists to proactively prepare for 2020 through development of a comprehensive education and training strategy.

Jan 1, 1998

After World War I the character of my mining life changed completely. Before then adventure had been almost continuous but after the war there was lots of staying in one place, almost routine, between adventures. This was fortunate, as the life of a mining engineer is a wandering one at best, and it makes being married and raising a family a dubious enterprise. It would have been quite out of the question with the life I led before I got married at the end of the war The new sort of life made the "beaconing of adventure" intermittent. There were often long stays at home between wanderings which was fortunate as it changed the continuity of these memories. I must briefly summarize accounts of the more or less routine periods and concentrate on the occasional exciting episodes between. After a long visit with friends in Berkeley, Dorothy and I left for Arizona and three days at the Grand Canyon that were nearly too much for both of us. One beautiful day we started a short walk down the Bright Angel Trail. It was such a lovely bracing day that we kept on walking and enjoying the views until, just after noon, we reached the Colorado River. We were the only ones in sight so to enjoy the sunshine to the full we both had a good swim in the swiftly flowing river. So far, everything was wonderful. But when we started to climb back up the trail, rising nearly 6000 ft in ten miles we soon found that we had counted too much on our youth and endurance. We had to rest every few hundred feet and it seemed as though we would never reach the top. It was eight o'clock in the evening when we finally staggered into our room and collapsed. On the way to the Canyon I had seen John Greenway and Dr. Ricketts in Santa Barbara and they had little idea what would happen to them or to me. Before resuming his position as general manager of Calumet and Arizona and New Cornelia, Greenway must recover from the effects of the gas he had suffered in the war. Dr. Ricketts

Jan 1, 1976

By Dave Capstick, Ken Garner, Jim Porter

Technologies and systems used in the management of energy consumption in the mining and metal processing industry are well understood and documented from the supply side of the business. It is our contention that in many instances, through a more complete understanding of the demand side of the business, based on the detail of the operations plan, will provide greater lead time in terms of the design, implementation and utilisation of power supply infrastructure. Thus, optimal management of demand in a proactive manner, based on production requirements, will ensure both security of supply as well as continuity of operations. This paper describes the technology and methodology that is being developed to enable the above statement to be achieved. We use a case study to demonstrate the ability of the tools and methodology and conclude by outlining the business benefits achievable as well as the future developments emanating from this initiative.

Jan 1, 2005

By Glenn J. Phillips, Debra L. Musick

The operating mine is dynamic, everchanging, and a continuous moving target. The only way to effectively manage such a creature is to be able to evaluate the cost of operation over short enough time periods that rapid effective controls can be implemented before loss can erode the marginal profits in todays market place. Such short term evaluations can provide the basis for the long range planning that can keep an operation healthy in the future. The spreadsheet programs on small computers (PC's) offer the possibility of such evaluation by accumulating data in a useable format, providing timely cost reporting and providing a tool for use in evaluating the day to day alternative choices of the real mining world.

Jan 1, 1987

By S. K. Palm

Volatility is a fact of life in the mining industry. Prices of and demand for mineral products are among the most volatile of those for any product. The volatility of these markets wreaks havoc on both corporate management and the personal lives of mining people. Yet, until recently, it has been difficult to assess the impact of volatility on business strategy. This paper discusses how mining firms can profit from market volatility through an operations strategy that stresses operating flexibility. The foundation for our strategy analysis is the observation that a mine is analogous to a stock option. Techniques based on those developed to value stock options have recently been extended to the field of mine valuation. The insights provided by option pricing are very valuable in the development of mine operating strategy.

Jan 1, 1986

By Vincent R. Bovino

The future of coal mining is bright - only if we realize and then manage as though we are competing in the world marketplace. Accept it or not, our market is global. We tend to think our problems are caused by the uncontrolled foreign production of coal, and the uncontrolled drop in coal prices. I submit that our problem is not the world pricing structure - part of our problem is our on-site cost structure - our productivity. We are the world's best at getting out the tons - that is, production. Most mine managers thrive on that. What is in serious doubt is our productivity - our ability to produce tons of coal in a cost effective manner. Please think about the difference: ? Production is tons of coal. ? Producitivity is decreasing the cost per ton of coal. Our future is bright, only if we can increase our productivity by trying different and new ways to manage our businesses and our people. Unlike the easy successes during the 60's and 70's, success in the decades ahead will depend on our ability to achieve greater levels of productivity. If mining and other old line smoke stack industries are experiencing difficult times in 1986, three years into an economic recovery, what will happen when the economy cycles downward? Any operation can achieve unlimited productivity by developing the resources within their employees. As an industry, we have harvested the

Jan 1, 1986

By Hagan T. N, Tucker A. J

The Cumnock Open Cut Mine (COCM) is located in the Hunter coalfield in New South Wales. Five coal seams are being mined, mostly by drilling and blasting, loaders and excavators, and trucks. The annual production of coal is 1.3 million tonnes. Overburden and interburdens consist mostly of siltstones and medium to thickly bedded sandstones. The strata dip to the south-east at approximately four degrees. There are no major faults in the rock mass.

Jan 1, 1995

By Hanjie Chen

A mine panel collapse may occur when pillar sizes are too small or the surrounding rock strata (roof or floor) yields. After a small pillar fails, its loading is rapidly transferred to adjacent pillars that in turn fail. If the surrounding rock strata yield, the loading on pillars will redistribute. which may result in some pillars under high stress. This paper analyzes the causes of two cases of mine panels failures in two room and pillar mines. One case of massive pillar failure occurred in a phosphate mine and the other, mine panels failure, is in a coal mine. In the phosphate mine, both the roof and floor strata were a thick competent shale stratum. The finite element analysis shows that the major reason for the massive pillar failure is that the pillar sizes were too small in a panel. In addition, the high cliff topography has some influence on the failure. In the coal mine, the failed area was about 1,000 ft long by 760 ft wide (covering more than 3 panels) involving 390 pillars. The harrier pillars between the panels were punched on retreat into small chain pillars and the extraction ratio in this failed area was more than 80%. The roof remained intact, and pillars were crushed and punched into the floor. Based on the stress analysis, it is found that multiple panel collapse occurred because the barrier pillars were punched into small pillars and the loading on panel edges increased due to floor failure.

Jan 1, 1999

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of a massive pillar failure in a room-and-pillar mine. The mine employed a nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated out by quickly, and, within 24 hours, it had covered an area approximately 1,250-m- (4,100 ft-) long by 762-m- (2,500-ft-) wide. The failure was caught and stopped by a solid barrier pillar. Using computer modeling, this study indicates that the massive failure was initiated because of a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of the absence of barrier pillars between some panels and between mains and panels. Based on computer modeling, alternative mine plans were proposed to avoid such problems.

Jan 1, 2002

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By A. K. Kuhn

In virtually all jurisdictions, comprehensive environmental protection regulations or standards are in place that apply to all industries, including mining. The only other legitimate mine-permitting concern is post-mining land use (PMLU). PMLU includes all uses of land after mining as well as the ecosystems appropriate for those uses. Although flawed, the New Mexico Mining Act (NMMA) of 1993 is a PMLU-based permitting statute. It requires measures during closure that will establish a PMLU or self-sustaining ecosystem for each mine unit. PMLU-based permitting avoids prescriptive, one-size-fits-all measures and keeps permitting focused on the legitimate goal of responsible land management..

Jan 1, 1999

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don't always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By Ravi Ray, Kostas Kaklis, Zach Agioutantis

"Modern underground mining is becoming more complex and geotechnically challenging. The engineer uses numerical, analytical, and data-driven methods (empirical and/or experimental) or their combination to overcome these challenges. Each method has its advantages and disadvantages. Nevertheless, given the amount of innovation and experience involved in developing each of these techniques, it will be prudent to use all their benefits rather than favoring one technique over the other. Pillars are the most important support element in an underground mine. A holistic geo-mechanical solution needs to be determined to design mine pillars using a proper sequence and exact mix of the three methods. A combination of these methods, in sync, can encompass the several advantages of the three methods while eliminating their disadvantages. This paper presents a conceptual three-tier solution to the pillar design problem, to improve its design pedigree, using a proper combination of numerical, analytical, and data-driven methods. At the focus of this proposed method lies the Ground Reaction Curve (GRC) concept.INTRODUCTIONAlthough the stability analysis of underground excavations is a challenging problem, its understanding has improved tremendously over recent years through the use of improved tools and techniques. The trial and error method was replaced with more scientific methods like the empirical and analytical methods that are still in use today. Empirical methods were developed based on large data sets obtained from experiments and observations (e.g., coal pillar strength equations). Analytical methods were developed based on mechanical understanding of stability (e.g., safety factor for vertical pillar loading, Convergence Confinement Method). Improvement in computing power and numerical techniques led to the development of several numerical methods (e.g., finite difference, finite element) suitable for geo-mechanical analysis.Each of these methods have certain advantages and limitations. Nevertheless, the user is often puzzled over the proper method selection and over the proper sequence of using them. This exercise becomes more challenging when different methods are combined, where, for example, one has to estimate the pillar strength based on empirical equations (e.g., Mark-Bieniawski coal pillar strength equation), determine the factor of safety based on an analytical approach (e.g., tributary area load divided by pillar strength), and analyze pillar-strata interactions using numerical analysis (see Esterhuizen, Mark, and Murphy, 2010b).Challenges increase when current pillar design methods are designed as passive structures to balance the fixed dead weight of the overburden. This classic suspension design approach does not recognize the self-stabilizing capacity of the overburden (Frith and Reed, 2018). A practical solution to address these issues is the use of numerical analysis. However, one should always keep in mind that the numerical modelling approach may have certain practical limitations."

Jan 1, 2019

By David H. Tang

Massive pillar failures were observed at two underground coal mines. The results of stability analysis using traditional pillar design formulae did not agree with the underground observations. Finite element models were used to analyze the causes and mechanisms of the pillar failures. The results were confirmed by the underground observations. Finally, the improved mine plan for each case was derived to ensure the stability of the underground structure.

Jan 1, 1990

Mine pit slopes in the Pacific Rim are a geotechnical challenge because of the complex geology in which they are developed. Mines are currently being fast-tracked to meet the increase in commodity prices, often resulting in some reduction in ground studies and short-cutting of design procedures. In addition, the resources boom means that skilled personnel are in relatively short supply. At a time when mine pits are getting bigger and deeper, and the engineering is getting more demanding, there is an increased demand on managers to effectively implement the work.   Experience both in New Zealand and the Philippines, display the complex range of geological environments in which pits are being excavated. Working in these conditions has shown that successful geotechnical design requires a strong geotechnical model based on sound geology. An appropriate level of investigation and analyses results in a certain level of understanding for the mine design. There is a point where additional expenditure (on investigation and analyses) is not warranted based on the expected minimal impact on decreasing the level of perceived risk on the project. For most projects in our experience the analytical methods and complexity of geotechnical assessment changes increases as the level of knowledge grows.

Jan 1, 2006

By J. M. Mercier

Approximately seven (7) years of recent intensive mining activity in the Wasatch Plateau Coal Field of Utah has revealed distinct geologic patterns which, at times, profoundly influence reserve estimates, coal quality, mine layout, and reserve accessibility. Mine planning, economic feasibility, and resource recovery activities by Getty Coal Company utilize a multi-faceted approach by necessity when evaluating Utah properties. Two specific operating mines offer examples of the affects of adverse geologic conditions on mine operation and project economics.

Jan 1, 1984

By Kadri Dagdelen, Steven Hoerger

For gold mines, orebody uncertainty is one of the leading causes of differences between planned and actual production. Geostatistical conditional simulations create multiple equally probable orebody block model realizations which are conditional to the current drilling information and demonstrate the sampled grade distributions and spatial statistics. These simulated block models are key inputs for a stochastic evaluation to show the likely range of grades and cash flows to be delivered by a mine plan. The stochastic evaluation outputs can be used to compare different mine plans in terms of expected values and risks to planned grades, production, costs, Net Present Value (NPV) and other plan metrics. For the McLaughlin gold mine, risk profiles are demonstrated to show how different mine, cut-off and stockpile strategies can reduce risk and improve expected value. The strategies considered were effective in improving expected NPV and reducing or eliminating tonnage uncertainty, but the strategies had little impact on reducing the uncertainty of NPV’s or mill grades. The stochastic evaluation process is also used to compare the risk impact of orebody uncertainty against the risk of not achieving planned mining tonnages or vertical advance rates. Risks for plans created with and without stochastic mine plan optimization are also compared.

Feb 1, 2025

By L. B. Phelps

This paper focuses on the use of an integrated mine planing software package entitled "REMINE" which was constructed to provide a project evaluation tool for analysis of remining projects. Coal remining constitutes the affecting of sites which have had a past history of mining and have a pre-existing pollutional discharge. Such sites require a Best Professional Judgement (BPJ) analysis. The program was written to provide such an analysis with flexibility in the mine plans which can be analyzed. The process required for a BPJ analysis will be detailed and mine plan simulation performed to demonstrate the analysis.

Jan 1, 1990