Search Documents

By Aaron Noble, Mahmud Esad Uluer

Respirable coal mine dust (RCMD) is one of the biggest occupational health hazards for underground coal miners. Dusty mining environments can cause long-term health problems, including pneumoconiosis and progressive massive fibrosis. The Mine Safety and Health Administration (MSHA) has recently revised regulations promoting enhanced dust mitigation technologies, which have sparked renewed interest in the development of dust mitigation technologies. The flooded bed dust scrubber (FBS) is one of the most widely used technologies; however, it is limited by technical challenges, the most notable being the potential to clog. Recent studies have shown that applying vibration to filter mesh can improve the overall efficiency of the scrubber and that the system can be readily integrated to existing continuous mining equipment using an energy harvesting approach. In this follow-up study, the impact of mesh design and surface modification on system efficiency was examined using different vibrating liquid-coated stainless-steel mesh panels in a laboratory-scale FBS. Based on the two-way interaction data from a multi-factor experimental design, the results show that the performance of the system can be optimized by using hydrophilic 20- or 30-layer filters and by excitation frequencies between 67 and 134 Hz. This laboratory study suggests that a 20-layer mesh screen with hydrophilic surface applications and optimized vibration parameters can perform similar to that of a 30-layer static mesh, which is typically used in industrial units.

May 23, 2024

By Lu-ming Zhao, Li Zhao, Yu Wang

In this paper, the change of crystallization rate, dendrite arm spacing and dendrite width of mold flux with various magnetic field conditions were studied by experiment. Having found that the crystallization ratio of mold flux increased from 33 to 96.6%, the dendrite arm spacing decreased from 72.47 to 38.02 lm, the dendrite width decreased from 48.47 to 27.02 lm while the magnetic field frequency (f) equaled to 8 Hz and its strength (B) increased from 0 to 30 mT. The crystallization ratio of the mold flux increased from 91.9 to 96.1%, the dendrite arm spacing decreased from 60.53 to 28.08 lm,the dendrite width decreased from 42.53 to 24.08 lm when B equaled to 20 mT and f increased from 6 to 12 Hz. However, the XRD analysis indicated that the phase types of the mold flux under the experimental conditions did not transform. Results showed that an alternating magnetic field can promote the crystallization of mold flux and refine grain structure.

Mar 1, 2018

By D. Yu, Y. Thibault, D. Paktunc

"Prereduction and flux-aided direct reduction of chromite provide significant advantages in reducing energy consumption and greenhouse gas emissions during ferrochrome production. In this investigation, a comparative evaluation of the influences of several alkali fluxes was carried out based on experimental observations supplemented by advanced material characterization and thermodynamic predictions. Direct reduction of a chromite ore with alkali fluxes at 1300°C for 1 hour produced (Cr,Fe)7C3 type alloys with Cr/Fe mass ratios from 0.7 to 2.3. Among the alkali fluxes, reduction aided by NaOH resulted in a high degree (85%) of Cr metallization with the ferrochrome alloy being Cr4.2–4.6Fe2.4–2.8C3. The formation of liquid slag, which facilitated Cr metallization, was limited by the formation of NaAlO2 between 800 and 1300°C. This, in turn, restricted the collection and transport of the charged ionic Cr species (i.e. O2–) to graphite particles. Under the conditions studied, ferrochrome particles were often small and largely unliberated, which would make the physical recovery of ferrochrome challenging. At 1400°C, the amount of liquid slag increased, enabling the growth of alloy particles. Direct reduction of chromite aided by NaOH is promising as an alternative technology to conventional flux-based smelting in electric arc furnaces. IntroductionConventional smelting processes are energyintensive (Riekkola-Vanhanen, 1999) with the energy requirements greater than 4 MWh/t (Naiker and Riley, 2006; Beukes, van Zyl, and Neizel, 2015), and the greenhouse gas emissions can be significant, exceeding 10.5 t CO2 per ton Cr in ferrochrome produced (International Chromium Development Association, 2016). These include emissions occurring on-site (smelter), emissions due to electricity production, and emissions due to upstream processes. Overall energy requirements are influenced by the degree of prereduction and smelter charge temperature. Significant reduction in electricity consumption can be realized if the charge is prereduced before feeding to the submerged arc furnace (Niayesh and Fletcher, 1986). This consideration has led to the development of several prereduction technologies, with the most important example being the Premus process. In comparison to the conventional smelting processes, this prereduction process lowers the overall energy consumption and greenhouse gas emissions by about one-third (Naiker, 2007)."

Dec 1, 2018

By Liangying Wen, Jian Xu, Dongdong Wang, Kaihui Ma, Yang Xu

Slags play an important role in blast furnace operation, and their com- positions are based on the CaO –SiO2–MgO–Al2O3 quaternary system. However, there is not a clear understanding of the effects of gangue on of the formation of FeO-bearing primary-slags process in blast furnace. In this work, the softening and dripping experiments under the blast furnace conditions are designed to explore the influences of CaO-/SiO 2-/MgO-/Al2O3 on the softening and melting properties of FeO respectively. The results indicate that additions of CaO or Al2O3 decrease the starting softening temperature and no dripping behaviors are found in comparison with the base case results when only FeO is used. On the contrary, the addition of SiO2 or MgO rises the starting and ending softening temperature, as well as the dripping temperature. The lowest maximum pressure drop is obtained in the case with addition of SiO2. According to XRD analysis results, the initial phase with CaO addition in the primary-slags should be CaOFe3O4 and that with SiO2, MgO, Al2O3 additions are fayalite (2FeOSiO2), magnesioferrite (MgOFeO), hercynite (FeO2Al2O3), respectively.

Mar 1, 2017

By Yi Luo

The potential influences of mining subsidence on structural stability, integrity and functionality of guyed tower structures have not been systematically studied before. This paper presents a ease study where a guyed steel tower of a telecommunication company was mined under by a longwall operation. Prior to mining, every aspect of the subsidence influences to this structure was studied. The pre-mining assessment indicated that the structure could experience vibration problem in the second half of the dynamic subsidence process. Bawd on the study, a simple mitigation measure was recommended and implemented and the structure was successfully protected.

Jan 1, 2003

By Alexander I. Raitchenko

"Although one takes into account only thermal expansion usually at analysis of convection onset, the essential factors include magnetic and electric fields. If Lorentz-force originating from intercrossed electric and magnetic fields' action is directed downwards its effect strengthens gravitational action, and value of critical Rayleigh number (limit value for convection onset) must decrease; increasing of critical Rayleigh number should be observed in case of Lorentz-force directed upwards. Extent of such an influence is determined by relation of Lorentz-force to hydrostatic head in gravitational field. Competition between electromagnetic force due to nonuniformity of electroconductivity (on account of its temperature dependence) and electromagnetic buoyancy force may have ambiguous effect: both increase or decrease of critical Rayleigh numbers. Proposed conception is applicable to analysis of situations in liquid conductors and conductive gases.IntroductionStatic or dynamic situations in fluid media are determined besides properties of these media by a variety of external influences. However one correlate~ the onset of the convection and its development with influences of the minimum quantity of external causes frequently. Most known and usual factors are the gravitational and temperature fields. The number of processes includes heat generation in media volume, and theoretical analysis in these cases takes into account this interior heating together with boundary temperature conditions. But explanation of many natural and technical events is not complete and cogent within limits of thermo-gravitational terms. The whole complex of acting factors which influence convective processes in techniques and nature is greater in many cases. In particular the action of · electromagnetic nature often has not less importance than gravitation one. Stability or instability of a current layer in the plasma must be determined by non-uniformity of electroconductivity owing to non-uniformity of temperature [1]. The presence of Joule dissipation in the plasma through which the electric current flows stipulates initiation of origin of overheated instability [2]. It is known that electroconductivity of arc in the boundary zone changes sharply with radial distance [3], and this must influence its stability essentially. If the intercrossed electric current and magnetic field begin to act on an electroconductive fluid besides the non-uniform temperature field and the gravity, the conditions for the onset of the convection change radi- . cally: both the temperature field and their solutions have to be changed also. The analysis of equilibrium single-time correlation functions of fluctuations must be employed for situations with enlarged number of factors as this was in case for the Rayleigh-Benard problem where the object is a horizontal layer of liquid. This can be carried out by taking into account the detached forces' correlations [ 4, 5]"

Jan 1, 1999

By C. Gatschlhofer, A. Krammer, H. Raupenstrauch, T. Hochsteiner, A. Holzer, L. Wiszniewski

The rising demand for lithium-ion batteries, coupled with international climate targets, emphasises the need for circular economy and zero-waste recycling approaches. However, so far, no industrial-scaled solutions are available that fulfil global recovery targets. Therefore, a novel pyrometallurgical reactor was developed at the Chair of Thermal Processing Technology at Montanuniversitaet Leoben to avoid lithium slagging and recover volatile elements via the gas phase. Nevertheless, previous results show that several impact factors, including interfering elements or pre-treatment steps, strongly limit the recycling efficiency of black mass. To simulate the black mass and provide feedback on possible influences of pre-treatment steps, cathode material from production with additives of interfering elements was analysed regarding melting behaviour. The results show that formation of a further processable alloy was increased by almost 50% when pretreatment steps were excluded, indicating pre-treatment steps as a major influence to be considered within this specific recycling route.

Jan 1, 2023

By Sugui Tian

By means of the T6 treatment, the measurement of creep curves and microstructure observation, the influence of T6 heat treatment on the microstructure and creep properties of Ti-6Al-4V alloy is investigated. Results show that the microstructure of the forged alloy consists of the banded-like a phase and networks b phase. After sub-temperture T6 treated, the microstructure of alloy consist of the block a phase and ?networks basket? structure. Under the conditions of the applied stress of 575 MPa at 4000C, the forged alloy displays a lower creep lifetimes, after T6 treated the creep lifetimes of the alloy is enhanced to 548 h from 66 h, which is attributed to the formation of the network basket structure in which the needle-like phase are dispersedly distributed. As creep goes on, the denser dislocations in the a phase are concentrated to occur the dynamic recrystallization for refining grain. which is a main reason of the alloy displaying a better creep lifetimes and plasticity. Thereinto, the creep mechanism of the forged alloy is thought to be the slip of the straight <a> and <a+c> dislocation are activated on the prismatic planes and pyramidal planes, while the creep mechanism of T6 treated alloy is that wave-like <a+c> dislocations are activated on the pyramidal planes.

Jan 1, 2009

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By Leandro de Almeida

Tiras e chapas de cobre e suas ligas possuem excelentes propriedades térmicas, elétricas e mecânicas simultaneamente e por isso podem ser utilizadas na fabricação de inúmeros produtos através de processos de conformação. Determinadas características devem ser analisadas na chapa antes mesmo do processo de manufatura, visando eliminar possíveis falhas durante as etapas de produção. Especificamente para o processo de repuxo profundo, faz-se necessário avaliar a possível formação de orelha e o possível afinamento da espessura da chapa durante a conformação. Sendo assim, o levantamento dos coeficientes de anisotropia planar ?r e o de anisotropia normal r são essenciais para se obter bons resultados nos processos de conformação. O presente estudo tem como objetivo avaliar a influência da deformação (e) na obtenção dos coeficientes ?r e r na liga UNS C22000, utilizada especificamente para a produção de projéteis A norma ASTM E 517 que apresenta a metodologia para se determinar esses coeficientes não especifica claramente qual e a ser utilizada. Os resultados alcançados não demonstram diferenças significativas com relação a e utilizada nos ensaios, ou seja, os coeficientes obtidos utilizando 0,10, 0,15 e 0,20 de deformação são os mesmos.

Aug 17, 2017

By Rodrigo Martins Barbosa

A água é utilizada em processos industriais desde o começo da era industrial. Sua utilização é variada, desde como matéria prima, até como utilidades. Muito se discute a respeito da qualidade da água para descarte e seus possíveis danos ambientais, mas é importante mostrar que, além disso, existe um impacto financeiro ao trabalharmos com a má qualidade da água industrial. Este trabalho propõe demonstrar a influência da qualidade da água nos processos industriais, através da avaliação do resultado da instalação de um filtro de água na tubulação de entrada de um trocador de calor.

Aug 17, 2017

By Luis Miguel Panduro Robles

"La aireación forzada busca acelerar la cinética de extracción del cobre en el cobre a través del oxígeno del aire al ion ferroso que se encuentra presente en las soluciones de lixiviación formando el ion férrico; elion férrico formado de esta manera oxida a su vez al cobre metálico (de la calcosita y la bornita) o al azufre (de la covelita primaria o residual) reduciéndose a ion ferroso. El ion ferroso formado se vuelve a oxidar conoxígeno y así continúa el ciclo hasta que todo el mineral sulfurado ha sido oxidado. En ese sentido, el presente trabajo describe las evaluaciones realizadas en Cerro Verde que analizaron el requerimiento de óxigeno en una pila industrial, la determinación del diámetro de orificio óptimo para las tuberías de aireación y el tipo de tubería más adecuado para la aireación."

Jul 31, 2003

By Esteban Maldonado, Luiz Castro

En el presente trabajo se presenta un análisis de estabilidad de un talud del tajo de 300 m de altura y un ángulo global de 40°. Esta pared está compuesta por roca sedimentaria con presencia de juntas y estratificación. La resistencia del macizo rocoso ha sido expresada a través del criterio de Mohr-Coulomb que considera los parámetros de resistencia equivalente obtenidos a partir de la envolvente de falla de Hoek & Brown generalizado (2002). Para el análisis de estabilidad fue usado el método de equilibrio límite y el criterio GLE/Morgenstern-Price y el programa computacional Slide (Rocscience, 2015) y se utilizó la opción de “Anisotropía Generalizado”.

Sep 1, 2017

By Sergio Castro

Los modelos geotécnicos disponibles suelen estar basados en las litologías existentes, sin considerar el impacto de las soluciones hidrotermales en las rocas y, por tanto, en la estabilidad de los taludes de un tajo abierto. El estudio de caso presentado en este artículo muestra que realizar una zonificación en términos de los tipos de alteración hidrotermal es muchas veces necesario; pero también que ello debe acompañarse de investigaciones geotécnicas adicionales y un análisis de la estabilidad física de taludes, con el fin de lograr un rediseño basado en la variabilidad de la resistencia de la roca en cada tipo de alteración, ya que el efecto puede haber sido tan intenso que la roca termina transformándose en un suelo residual.

Jun 30, 2020

By Daniel Asunción García Ramos

El presente texto señala la influencia del quebracho como agente tensoactivo que evita el problema causado por el azufre a través de concentrados, cuyas especies mineralógicas predominantes son: esfarelita, pirita, incrementándose la extracción de metales. En este sentido, este método hidrometalúrgico permite que los concentrados que tienen plomo y arsénico en su composición, sean neutralizados para neutralizarlos como sulfatos sólidos, mientras que los sulfuros de zinc y de cobre pasan a la solución acuosa en estado iónico para ser recuperados posteriormente por electrodeposición.

Dec 1, 2015

By Gilberto Yanarico Apaza

"El presente texto señala las pautas necesarias para realizar una evaluación técnica integral de la influencia del collar de bolas para las operaciones de molienda, afectando al desgaste de los revestimientos de los molinos convencionales. Para la determinación del collar de bolas es necesario realizar los análisis granulométricos con la finalidad de obtener el F80 y el P80 de las muestras obtenidas en la alimentación y producto de los molinos, definir el índice de trabajo (Wi) y consumo de energía. Asimismo, se debe considerar el porcentaje de la velocidad crítica, las dimensiones de los molinos, la densidad de los medios de molienda (bolas), el porcentaje de la carga de bolas, las características geométricas de las bolas para molienda y el diámetro real de bolas, que influye de forma inversamente proporcional en la tasa específica del consumo observada."

Jul 1, 2015

By César Augusto Martín Hilser Vicuña

El "Punto de fluencia” es el contenido de humedad crítico a partir del cual un mineral concentrado sufre “liquefacción”, es decir, libera la humedad como agua libre al ser sometido a las sacudidas propias de una travesía por mar. En esta perspectiva, el presente texto correlaciona la influencia que tiene el proceso de producción de los concentrados en el punto de fluencia a través de los siguientes factores: granulometría, efecto de los reactivos de flotación y la mineralogía. De forma que al conocer los factores que influyen notablemente en el valor de la humedad límite de transporte, se evita los riesgos de que la carga sufra licuefacción durante su transporte por mar.

Sep 14, 2009

By Daniel García

La lixiviación por presión es una alternativa hidrometalúrgica desarrollada para minerales metales básicos, donde se reduce la contaminación generada por solubilización del azufre y su separación. En este sentido, el presente texto señala la influencia del quebracho como agente tensoactivo que evita el problema causado por el azufre, utilizando concentrados cuyas especies mineralógicas predominantes son: esfalerita, pirita, galena y cobre grises, de forma que incrementa la extracción de los metales de valor, entre otros.

Oct 21, 2015

By Héctor Benavente V

La presente investigación señala el comportamiento de la cinética de flotación para los sulfuros de cobre y molibdeno en las condiciones de operación de la concentradora de Toquepala. Para ello, se consideran dos variables: tamaño de las partículas y el tipo de colector utilizado. Una vez obtenidas las variables, se optimiza la recuperacíón de los sulfuros en los rangos granulométricos que lo requieran.

Aug 26, 1988

By Fabio Da Costa Garcia Filho

O uso de resíduos de vidro como aditivo mineral finamente moído, em substituição parcial de cimento e agregados é uma direção promissora para a reciclagem. Este trabalho teve como objetivo analisar a influência de resíduos do processo de corte de vidro em argamassa adesiva, como substituição parcial de cimento e agregado miúdo. O vidro em pó foi utilizado em percentuais de 10, 15 e 20% em peso em substituição ao cimento Portland e, em outro momento, em substituição ao miúdo agregado. Verificou-se que a substituição refletiu positivamente sobre a resistência à adesão da argamassa, com o aumento da temperatura de cura.

Oct 30, 2017