Search Documents

By Y. G. Yaroshenko, V. Y. Baldin, Y. M. Gordon

The manufacture of sulphuric acid from the off-gas of pyrometallurgical processes in the production of heavy metals is one of the common methods of effective recycling of sulfuric anhydrite. The new Impact-Inertial Devices with the rectangular contact channels (IIRCh) and the internal circulation of liquid allow the injection of an absorber into the phase's interactive cell by utilizing the gas stream energy and by this way increasing the sulphuric acid yield and reducing the power consumption. These devices have the following advantages: simplicity of design, smaller size, low capital expenses, absence of irrigating system, high operational reliability, simultaneous cleaning of solid, gaseous and liquid impurities and also cooling of gases etc. The IIRCh efficiency is almost 18 % higher and they require 1.3-2 times lower energy when compared with Venturi Absorbers. Also the elevation of spraying nozzles or injectors is 1.5 times lower in the IIRCh case.

Jan 1, 2004

By C. B. Piazzarollo

Ceramic materials exhibit dispersion results after being subjected to various levels of stress, from the point of view of mechanical strength. With the focus on sustainable development and to improve the strength of these material, was incorporated ornamental rock waste into clay in up to 10% in mass to conform some samples, that was fired to 750ºC, 850ºC and 950ºC and submitted to technological tests. This paper presents an analysis of the technological properties of the samples through the use of Weibull statistic to determine which the best firing temperature for these red ceramic materials. The Weibull Modulus indicates a greater homogeneity for samples with 10R at 950ºC.

Jan 1, 2015

By A. P. Yovanovic, P. Bonadia, M. N. Moraes, C. F. Matos

"The magnesite flotation operation of Magnesita Refractories, in Brumado – Brazil, has four parallel ball mills working in closed circuit with hydrocyclones to grind the ore for the reverse flotation of silicates in mechanical cells. The modification proposed here opens the circuit for three of the ball mills so that their products are collected together to feed a high frequency screen. The oversize of the screen feeds the fourth ball mill in closed circuit for secondary comminution. The product reports to dewatering and flotation. The undersize undergoes desliming and subsequent flotation operation. According to pilot tests performed, the modification on the magnesite flotation operation will promote a 20% increase in the productivity, 8.5% increase in mass recovery and a 26% reduction in water consumption. The gains are due to the fact that the silicates in the feed are concentrated in the smaller particles (<100µm) with over grinding in the existing closed comminution circuit, making it impossible to take advantage of this natural selectivity. The combination of open circuit, more selective milling, and the high frequency screen, ensures high efficiency particle size classification. This renders the process more effective, both to the screen undersize with its high contents of silicates and fines, and to the screen oversize, which is almost without fines and has a higher magnesite grade. This situation allows for the setting of specific parameters for the flotation of both the primary milling undersize and the secondary milling product.INTRODUCTIONMagnesita Refractories, with its operations site in Brumado, is the largest producer of high purity dead burned magnesia (DBM) in Latin America. The magnesite ore is extracted from an open pit mine, named Pomba, after which it is crushed and handpicked. Due to the presence of disseminated silicate the ore has to be ground and concentrated by means of reverse flotation, before feeding the high temperature kilns for sintering and conversion to DBM.The magnesite flotation unit has an impact crusher to reduce the size of the feeding ore, which is transported to the mills by conveyor belts. The milling operation is composed of four ball mills in closed circuit with hydrocyclones. The closed circuit generates a high circulating load with excess fines, which is detrimental to the selectivity of the desliming and flotation operations, reducing both mass andmetallurgical recovery.In the current scenario, the capacity of the flotation plant is insufficient to meet the demand of the DBM kilns, forcing the operation to work with high purity ores in order to attain the highest possible mass recovery in the concentration process. This is not an ideal situation as it requires the mining site to work with higher stripping ratios.The objective of this work was to improve the magnesite flotation unity to increase its productivity. After a detailed analysis, the milling was identified as the limiting process, which made the authors to focus on this operation."

Jan 1, 2016

By T. A. Toney, L. R. Fish, P. J. Bethell

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers and recirculation have been attempted with some success. This paper reports on a novel (patent applied for) approach to retreating spiral middlings in a heavymedia cyclone circuit.

Jan 1, 2000

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By M. Townsend, E. L. Petsonk, H. Abrons, E. Daniloff, K. Kinsley

Workers exposed to certain inhaled dusts may show increased levels of nonspecific airways responsiveness (AR). In some studies, cigarette smokers have also been reported to have increased levels of AR. As part of an ongoing study, we compared the results of preshift methacholine inhalation challenge, spirometry, and smoking and occupational histories, in 191 under-ground bituminous coal miners (M) and 215 non-mining control workers· (C) . All M and c were selected to have normal baseline% predicted FEVI (PPFEV). Mining tenure was recorded as years worked underground (YRUG) and at the coal face (YRFC). AR was assessed as the% decrease in FEVI from baseline divided by the dose of methacholine delivered. M reported similar years smoked (YRSM) but fewer pack-years* (PY) than c~ Overall, both increasing YRSM and PY were associated with more AR*. Smoking C* but not M showed increased AR with increasing PY. In smoking and nonsmoking M, baseline AR and PPFEV showed no association with YRUG. The level of AR was inversely related to YRFC*, possibly representing selection away from dustier jobs. AR was inversely correlated with PPFEV*. In this study, AR and baseline PPFEV were not significantly associated with mining tenure, but cigarette smoking was related to both baseline lung function and level of AR. * p < 0.05 (Supported in part by Grant Gll35142, us Bureau of Mines, Generic Mineral Technology Center for Respirable Dust.)

Jan 1, 1989

By B. P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using carbonate solutions. The objective of the present study was to increase the absorption rate of CO2 into the carbonate solution without reducing the absorption capacity of the solution. This approach used a polypropylene glycol methyl ether (PPGME) as a surfactant to chemically alter the gas bubble size. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations of 0, 0.12, 0.24, 0.36, and 0.48 g/L. Results showed that as the concentration of surfactant increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 mmol/min CO2 at 0g/L PPGME to 3.92 mmol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in absorption capacity of the solution.

Feb 27, 2013

By B. P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using carbonate solutions. The objective of the present study was to increase the absorption rate of CO2 into the carbonate solution without reducing the absorption capacity of the solution. This approach used a polypropylene glycol methyl ether (PPGME) as a surfactant to chemically alter the gas bubble size. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations of 0, 0.12, 0.24, 0.36 and 0.48 g/L. Results showed that as the concentration of surfactant increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 mmol/min CO2 at 0 g/L PPGME to 3.92 mmol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in absorption capacity of the solution.

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By R Stimpson, B Johnson, B Hesse

During a period of twelve months between FY18-19, a series of trials were conducted to compare production drilling accuracy using two different methodologies, and the subsequent impact this had on stope performance (dilution and recovery). Testing was conducted at a series of underground mines in Australia. The drill rig’s existing alignment processes were compared to a new technology system, with the following observations: • The new technology was proven to limit rig alignment error, thereby reducing average blasthole deviation, resulting in an increase in the number of holes drilled within tolerance by up to 160%. • The increased accuracy reduced stope dilution significantly by reducing over-break of subgrade ore, whilst also increasing drilled meters (faster stope-cycle time), reducing the bridged tonnes ratio, and facilitating the capture of previously uneconomical stopes. A cost-benefit analysis extrapolated from each of the trials showed the extent to which the new technology, when applied to production data, reduced average dilution, increased ore recovery as well as general drill and blast productivity. In one such trial, the new technology was proven to have reduced average dilution by net 45.4%, which if applied to a full year’s production data, would result in AUD8.2M additional ore recovered, with AUD4.5M less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 to AUD106. This improvement was maintained over the following 12 months – reducing average dilution from 22% in FY17 to 12.1% in FY19.

Mar 15, 2021

By P J. A Lever

This paper presents details of CRC MiningÆs work with waterjet assisted blasthole drilling. The objective of this work was to investigate techniques that reduce the cost and increase the productivity of blasthole drilling. The focus is on a technology that uses a high pressure waterjet to assist the conventional rotary rock cutting action of a tricone drill bit. The potential benefits of this technique are increased productivity, reduced drill bit wear and reduced hole deviation and hence improved quality of drilling. This paper describes the results of a laboratory based experimental program comparing conventional tri-cone drilling performance to the proposed waterjet assisted approach. Additionally, work has been completed looking at the more practical issues around the collection and sampling of drill cuttings and water recovery (recycling) when drilling with a waterjet. These studies have demonstrated that waterjet assisted drilling can significantly increase the rate of penetration over conventional rotary drilling. For the best-case experimental result, the relative improvement was over 40 per cent. More importantly, it is a starting point for examining alternative uses of the additional drill productivity obtained from waterjet assisted drilling. For example, increased drill productivity could be used to improve rock fragmentation by drilling a tighter blasthole pattern in the same time period. an existing drill fleet, then the drill fleet size could be reduced, or improved rock fragmentation could be achieved by drilling a tighter blasthole pattern within the same time period.

Jan 1, 2004

By Gorken A, Mular M, Stewart A

PT Freeport Indonesia operates one of the largest copper and gold concentrator complexes in the world. Flotation is used to produce a single copper-gold concentrate. In 1995, PT Freeport Indonesia and Cytec Industries Inc established a joint p

Jan 1, 1997

By A. Angelov, U. Peukerd, S. Gaydardzhieve, A. Stefanov, K. Grossman, V. Stoilov

Flotation concentrate originating from the Asarel-Medet porphyry copper mining and processing complex in Bulgaria has been subjected to regrinding using a Ro-Star mill; the effects of which on the downstream metallurgical behaviour are discussed. Particularly the effect on the liberation degree was studied through an optical microscopy and MLA-SEM automated mineralogy. On the other hand, copper selective flotation of the reground bulk concentrate was realised to evaluate the anticipated metallurgical improvement. Process parameters such as involvement of prior hydrocycloning and variation of collector dosage have been evaluated. Within a two-minute residence time inside the Ro-Star mill, an improved liberation degree of the copper bearing minerals has been observed. As a consequence, enhanced copper recovery and selectivity against pyrite was noted. It has been found that in order to guarantee efficient flotation of the resulting ultrafine particles, a modified flotation regime (i.e. changing collector suite and dosages) should be followed. Keywords: RoStar Mill, liberation, flotation recovery, ultrafine particles

Jan 1, 2020

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

With increased emphasis on controlled blasting, which is the first and least-costly stage of comminution, ore grindability and plant throughput can be increased by 5% to 10%, and energy savings of up to 10% appear possible. Crushing and grinding efficiencies are presented for ore blasted under regular and adjusted field conditions. An economic analysis of drilling and blasting through crushing and grinding is presented, suggesting that cost savings approaching 10% may be achieved.

Jan 1, 1998

By Rais SA

In June, 1986, Freeport Indonesia, Inc., in conjunction with Out- okumpu USA, laboratory tested the Flash flotation concept on Primary ball mill underflow. These laboratory results indicated a possible 10% increase in precious metal recovery and 0.6% increase in copper recov- ery were available over conventional methods. By October of the same year two Outokumpu Skim Air SK-240 units were operational on one mill circuit and were achieving 5 to 10% increased recovery in precious metals with equal copper recovery at one percent higher final concentrate grade. Two more cells were purchased and installed on the remaining grinding circuit in July, 1987. As part of the installation of the Skim Air cells, an existing cluster of six 508mm Krebs cyclones were replaced by four 660mm Krebs cyclones. To reduce high circulating loads, these new cyclones were made horizontal at 45 degrees. This arrangement succeeded in reducing the mill circulat- ing load by 100% and has allowed for a 10% increase in throughput at the same grind.

Jan 1, 1988

The Anshan Iron and Steel Co. (AISC) broke its steelmaking design capacity in 1978, bringing its total production of steel products to 6.86 Mt. Located south of the industrial city of Shenyang, Liaoning Province, in northeastern China, it is by far China’s most important iron and steel complex, ranking twentieth among world centers. The complex represents a unique blend of old ecluipment and new ideas for increased production and improved products. Under a state plan, the Chinese hope to raise capacity to almost 15 Mt/a in the future. Originally started by the Japanese in the early 1920s, Anshan has had a rather turbulent 60-year history. It was disassembled by the Soviets after World War II, only to be reassembled by them in the 1950s. Production was also suppressed during the Cultural Revolution. Since the present-day organization, AISC, emerged, the center has experienced progressively improving conditions as well as increased production. Today, the center includes 10 blast furnaces, 24 open hearths, and two basic oxygen units, designed for 7 Mt/a ironmaking and 6.5 Mt/a steelmaking. In addition, it has six batteries of cokemaking facilities with combined 4.4-Mt/a capacity. Solid Iron Resources Anshan’s iron resources consist of a proven reserve base of over 7 Gt of 30~0 Fe, according to Kao Yang, president of the Anshan Iron Mining Co., a subsidiary of AI SC, Most of that, he continued, is amenable to surface mining. Five major mines located to the north and northeast of the city of Anshan are the principal iron ore producers. These mines trend in a somewhat circular manner and combined, represent an estimated 28.6 Ylt/a of ore capacity. In addition, some 2.2 Gt of magnesite, a necessary ingredient in steelmaking, are also part of the reserve base, according to Kao. Annual production is around .2 Mt/a of 47% magnesite, well over the steelmaking center’s annual requirements, Excess production is shipped to other steel-making centers. The largest of Anshau’s open-pit mines is the Chitashan operation with a design capacity of 8 Mt/a. Ore reserves here are well over a billion tons of 30% Fe. Earlier plans to expand production at this mine to 15 Mt/a, with the help of US Steel, have been temporarily shelved. The other mines in the district and their rated design capacity are: Kungchangling, 7 Mt/a; Donganshan, 6.4 Mt/a; Dakushan, 4.2 Mt/ti; and Yenchienshan, 3.0 Mt/a. The Kungchangling mine is the richest in terms of ore grade at 6076 Fe. Reserves are somewhat smaller at 100 Mt. The unit also operates a small shrinkage stoping operation. Ore grade at the other mines is usually 30-327. Fe. Llost mines operated at reduced capacity during 1979 owing to a natural gas shortage at the mills. The general

Jan 3, 1980

By Scott Jones, Tony R. A. Durkac, David W. Stephens

Williams Mine was considering spending a large amount of capital to install a pumping system underground to rid the mine of slimes; with the introduction of Delvo Stabilizer this challenge would be met. This paper will address the process to introducing the Delvo Technology into the Cemented Roddill Program. Some areas that were worked on included: testing of the mix design, bet dosage rate for an economical solution, temperatures at different levels of the mine, the amount of time needed once the grout was put to sleep, preventing plugs in the delivery system A controlled dosage that gave the Operator a 12 hour window of flowable material was developed and an added feature to the introduction of Delvo was also noted; an increase in MPa strength over the design. Collectively with the help of operators at the batch plant and the underground miners involved with the program all concerns where addressed and all goals met. A cost effective program was implemented thus increasing productivity, preventing costly plugs, and improved the actual maintenance on the entire delivery system, which included the batch tanks, aggitator tanks, all pumps required in the system and of course reducing buildup of slimes at the cones.

Jan 1, 2001

Due to collapsing copper prices during 1974/75, a rapid changeover was made at the C.S.A. mine from mechanised cut and fill stoping with incline access to the more economic long hole open stoping method. In 1974/75, 20 per cent of total production came from open stopes. For the 1976/77 year-to- date, more than 80 per cent of total production has been won from open stopes. As a result, mining performance has improved considerably. Stops, drilling performance has increased by more than 50 per cent since the changeover from extension rod, 50 mm diameter cut and fill uphole drilling to 115 mm diameter in-the-hole hammer drilling of holes up to 65 m long. Stops blasting performance has improved from 750 tonnes to 950 tonnes blasted per manshift. Open stope primary blasting per- formance is much higher, but reduces to 950 tonnes per manshift when secondary blasting and firing of hung drawpoints are taken into consideration. Ground control, the most expensive and least productive aspect of cut and fill mining, is almost entirely eliminated in long hole open stoping.

Jan 1, 1977

By Chris V. Sellathamby

Condition-based maintenance is replacing preventive maintenance in many industrial operations as a result of gains in productivity. Preventive maintenance is strictly time-based which means that as long as the prescribed time is sufficiently short, failures are prevented. The trade-offs between shorter cycles and increased downtime is a fine balancing act. Condition-based maintenance is gaining momentum as the more cost-effective and green solution to finding the optimal maintenance cycle and improving overall productivity. In the mining industry, various parameters of heavy equipment are monitored continuously to provide feedback for maintenance events. However, strain, shock, and vibration, key factors which lead to yielding and fatigue of metal parts, are not generally monitored by built-in systems, mainly due to the complexity of sensor installation and computational intensity of data processing. Scanimetrics has developed a stand-alone, add-on wireless system for measuring strain, shock, and vibration in heavy equipment and components, the data from which can be directly used to trigger maintenance events. The present system is being deployed in tar sands mining equipment. The system consists of a portable display and control unit, a software platform consisting of data management, sensor instrumentation and data analysis, and wireless strain sensor units, which can be easily installed on equipment. Data from the sensors can be gathered throughout the mine site, processed instantly, and used to generate condition-based maintenance events, improving overall uptime of the equipment and overall productivity of the mining operation.

Oct 1, 2010

By C. J. Newman

Production levels at the Kidd Creek copper operation increased during the 1980&apos;s by expansion of both the smelter and refinery and by major modifications to equipment which was causing bottlenecks. As a result, there was a significant reduction in the unit cost, some manpower reductions and hence a significant increase in productivity. In the last two or three years, there have been no major expansion projects leading to unit cost reductions and yet these have still been attained. This has been achieved by the development and implementation of various techniques designed to maximize the inherent potential of the operators and maintenance employees. This paper will initially describe the operation but will then place emphasis on employee involvement through such methods as idea awards, incentive schemes, loss control and continuous improvement programs. Organizational changes are discussed, particularly with reference to changes from the traditional operator role to one which encompasses maintenance skills and to cross-training of maintenance employees into multi-discipline fields. The effect of these changes are discussed by a review of the salient plant parameters of safety, production levels, cost and quality.

Jan 1, 1993