Search Documents

By P. S. Daly

"The purpose of this paper is to describe the types of instrumentation used at Sherritt Gordon's Ruttan Mine to monitor the"" effects of mining. The aim of the monitoring program is to establish parameters to achieve a maximum ore recovery with minimum dilut ion in a safe environment.The copper-zinc Ruttan Mine is in northwestern Manitoba, approximately 760 km from Winnipeg (Fig . I) . Production commenced in 1973 from the open pit at the rate of 10,000 tons per day. Pit bottom lies 58 metres above the first mine level. Underground development has overlapped with open-pit mining throughout. The open pit was phased out in the latter part of 1980.Underground production began in early 1979. The mining method employed in the first lift is sub-level blasthole open stoping with delayed hydraulic filling. Large-diameter (6.5-in.) holes are being drilled in the crop stope area and are also planned for some other areas for vertical retreat mining into a slot. GeologyThe orebody consists of numerous sulphide lenses of variable size, geometry and geology . The lenses occur within volcanoclastic host rocks which exhibit a strong variability in intensity and type of alteration and structural characteristics. Stope design and sequencing were based on these complex geological factors."

Jan 1, 1981

By William J. Conrad, Ryan J. Molka, Erik C. Westman

"In order to study pillar and overburden response to retreat mining, a ground control program was conducted at a Central Appalachian mine. The program consisted of several monitoring methods including a seismic monitoring system, borehole pressure cells in the pillars, and time-lapse photogrammetry of the pillar ribs. Two parallel geophone arrays were installed, one on each side of the panel with the sensors mounted 3m (IO ft) into the roof. A total of fourteen geophones recorded more than 5,000 events during the panel retreat. A MIDAS datalogger was used to record pressure from borehole pressure cells (BPCs) located in two adjacent pillars that were not mined during retreat. A series of photographs were taken of the pillars that had the BPCs as the face approached so that deformation of the entire rib could be monitored using photogrammetry.Results showed that pillar stability and cave development were as expected. The BPCs showed an increase in loading when the face was 115 m (380 ft) inby and a clear onset of the forward abutment at 30 m (100 ft). The photogrammetry results displayed pillar deformation corresponding to the increased loading. The microseismic monitoring results showed the overburden caving inby the face, again as expected. The significance of these results lies in two points, I) we can quantify the safe manner in which this mine is conducting retreating operations, and 2) we can use volumetric technologies (photogrammetry and microseismic) to monitor entire volumes of the mine in addition to the traditional point-location geotechnical measurements (BPCs).INTRODUCTION AND BACKGROUNDExcavation of underground openings is a difficult job in a challenging environment. The rigor of the process is compounded by the lack of a method that allows quantification of changes within the rock mass as excavation progresses. Statistics kept by the Department of Labor, Mine Safety and Health Administration show that 16% of fatalities and lost time incidents in the underground mining industry are due to unexpected rock mass failure (MSHA, 2015). A recent example is the Crandall Canyon, Utah, coal mine accident caused by the vertical collapse of a longwall coal mine on August 6, 2007 (Dreger, Ford, Walter, 2008)."

Jan 1, 2016

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

By Todd Minoski, Matthew McElhinney, Mark Mazzella, Morgan Sears, Craig Compton

The National Institute for Occupational Safety and Health (NIOSH) is staffed with Engineers, Geologists, and Field Technicians conducting a variety of ground control research. The mission of the ground control teams within the Mine Systems Safety Branch (MSSB) is to eliminate ground failures leading to mineworker injuries and fatalities. Advancing the science behind ground control relies heavily on conducting mutually beneficial research at participating mines which is detailed in specific references throughout the paper. The ground control teams have several types of field instruments at their disposal to measure the ground response in underground mines. These include borehole pressure cells (BPCs), vibrating wire stress meters (VWs), hollow inclusion cells (Hi-Cells), roof and rib extensometers, load cells, and convergence meters. These instruments are used to measure changes in pressure, strain, and displacement within the underground environment. Instrumentation data is collected automatically using intrinsically safe or MSHA permissible dataloggers if required. Information is transmitted to the dataloggers using approved cable to distances of 200–1,000 ft. depending on the type of datalogger being used. Once mining is completed, the dataloggers are retrieved and brought to the surface, providing in-mine data to mine management and engineers for the conditions currently being encountered in a particular mine. This data, in conjunction with geologic data and stress mapping, can be used to validate numerical models. The practical application of these models is extremely important for mine management and engineers, particularly when faced with more challenging mine environments. Insight gained from applying these models can be used to make better engineering-based judgments for areas that will be mined in the future. The impact of such applications can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 1, 2024

By Jinwang Zhang, Zhaohui Wang, Jiachen Wang

"Thick coal seams (seam height larger than 3.5 m) account for a large portion of the proven coal reserves of China, and underground thick coal seam mining provides about 50% of the Chinese annual coal production. Such seams are mainly mined using the longwall top-coal caving (LTCC) method. For safe and successful mining, a number of analyses on the stability of surrounding rocks in the LTCC face area have been extensively performed, and certain research achievements have been made. This paper introduces the main findings on rock pressure occurrence in the LTCC face during the last few decades and presents face and roof stability control techniques. INTRODUCTIONUnderground thick coal seams in China provide 1.8 billion tons of coal every year, which accounts for approximately 50% of the total Chinese annual coal production and 25% of the world, indicating that thick coal seams stand an important position in Chinese coal mining industry (Wang, 2005). Before the 1980s, thick coal seams were mined mainly by using the multiple-slice mining method. With the improvement of mining techniques and equipment in last two decades, longwall top-coal caving (LTCC) and high-seam, single-cut longwall are employed for thick coal seam extraction, offering advantages over multiple slicing from entry excavation and production perspectives (Wang, 2013).. The primary author of this paper introduced the most popular thick coal seam mining methods in China at the 30th ICGCM (Wang, 2015). This paper presents the stability of surrounding rocks in face area and ground control techniques for mining thick coal seams. For traditional longwall faces (seam height less than 3.5 m), the well-developed VoussoirVoussoir beam theory has been successfully used to analyze the movement of overlaying strata, which indicates that ground control techniques have become mature for this mining system. In such faces, the four-leg support with loading capacity of 4000–8000 kN is considered adequate for safe and successful mining. These faces normally have an annual yield of 1–2 million tons (Wang, 2007). For thick coal seams, however, the traditional support becomes inadequate and the ground control problem change to be more difficult and complex. Thus, development of large-scale mining equipment and ground control techniques for enlarged mined-out space and entries have been recognized as the most basic technical problems in mining thick coal seams."

Jan 1, 2017

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020

By T. N. Singh

Board and pillar system of mining has beer, practised in India in view of abundant availability of cheap labour force, low investment and quick return. Subsequently, selective mining from thick seems and partial mining under surface features boosted the trend. As s result over 2000 million tonnes of coal is locked up in form of developed pillars inclusive of about 1000 million tonnes of high grade coking coal in Jharia field alone. The trend of pillar formation is still uninterrupted as the estimated pillar reserve in this field in 1974 was only 700 million tonnes which increased to 961 million tonnes in 1983. The trend is not much different in other coalfields end as a rough estimate 100 million tonnes of virgin coal reserve is being transferred to pillar every year. The method of board and pillar mining is likely to remain moat preferred technology for decade9 to come in view of several inherent advantage in Indian mining conditions.

Jan 1, 1984

By S. M. Hsiung

This paper presents the results of an extensive study concerning a series of roof falls in a room-and-pillar coal mine located in West Virginia. Three dimensional finite element modeling was employed to identify the possible causes for the roof falls. The effectiveness of possible roof control measures for alleviating or eliminating the adverse roof conditions is analyzed, discussed, and compared. The best mining alternatives are recommended. It has been found that large overburden depth and typical roof geology are the major reasons for the roof falls. Angle bolting may not solve the problem encountered in the mine studied. Changing the mine layout currently used in the mine appears to be the best alternative. The recommended pillar size and entry width which will eliminate the problem completely are 90 ft. x 90 ft. and 14 it., respectively.

Jan 1, 1985

A review of ground control procedures in Western Australian underground mines is presented. Geotechnical input into initial mine design and methods of ground control is rare. As a result, the frequency of unexpected rockfalls is comparatively high, with over three quarters of the mines adopting non-specialist ground control designs experiencing unexpected falls-of-ground. In contrast, mines that provide some level of specialist input into initial ground control design experience decreased rockfall frequencies.

Jan 1, 1992

By M. Ge

Pattison Mine is a small sandstone mine located in Iowa. The sandstones produced by the mine are not common construction and aggregate materials. The stones are used to produce a special type of sand for hydraulic fracturing, a critical technique for recovering tight gas and shale gas. These sandstones are very different from the minerals and rocks which have been studied extensively in mining. On the one hand, they are brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, they are friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, a research program was set up by the mine and Missouri University of Science and Technology. This paper discusses the preliminary results of this investigation.

Jan 1, 2012

By C. Haycocks

In spite of the increasingly high capital investment required for longwall mining equipment, there continues to be a steady trend towards this form of mining. This move is caused in large part by improved productivity of longwall mining systems combined with greater percentage of coal recovered over room and pillar mining, reduced manpower requirements, and the inherent safety of the system. Longwall mining is most amenable to the greater depths experienced by many mining operations, particularly in the coalfields of the Eastern United States. Two primary problems in the installation of a longwall panel are determining whether a particular seam is suitable for longwall and, secondly, type and capacity of equipment required for such a mining operation. In addition, recent legislation has forced an evaluation of the surface effects of longwall mining with a view to determining what, if any, surface damage might result from extracting any particular panel. These factors must be determined using large and often complex quantities of geological, structural, mining, and surface data. This makes the problem most attractive to solution using the computer.

Jan 1, 1979

By H. D. Dahl

In January, 1969, the Central Research Division of Continental Oil Company initiated a research program on roof control. The purpose of the research was to improve roof stability. Toward this end, it was necessary to determine which of the many geological and geometrical variables have a significant effect on roof stability. The isolation of these significant variables would allow research effort to be concentrated where it would be most effective in improving roof control. The research effort was directed toward two major objectives. One was to de-fine the geological and/or geometrical parameters that affect the severity of roof conditions in any particular area of the mine. This study was concerned with roof fall intensity. The second was to define why roof falls in Humphrey No. mine (and in northern West Virginia-south-western Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. This study was concerned with roof fall orientation. To provide a reference framework for further discussion, a geological description of the area is presented in Part II. In Parts III and IV, the procedures, methods, and 'results of the research applied toward the afore-mentioned major objectives are presented. Part V contains the conclusions and recommendations for-warded by this study.

Jan 1, 1971

By H. D. Dahl, Roger C. Parsons

In order to improve roof stability, Continental Oil Co.'s research program, initiated in 1969, was directed toward defining the geological parameters that affect the severity of roof conditions in any particular area of the mine. In addition, the program was seeking to define why roof falls in the Humphrey No. 7 mine (and in northern West Virginia-southwestern Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. Conclusions and recommendations from this study of roof fall orientation are given.

Jan 1, 1973

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By Brian E. Travis

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to steel. The finished polymer mining grid product is a viable alternative to conventional supplemental roof control meshes such as chain link fence and welded wire. Polymer mining grids are a fraction of the weight, have comparable load support qualities, and will not rust or corrode in even acidic or alkaline conditions. Specific flame retardant additives can also be incorporated to make the polymer grid self extinguishing for use in underground "gassy" environments.

Jan 1, 1992

By Sanjay Kumar Singh

This paper presents ground control technology associated with a continuous mining operation for mass exploitation of underground coal deposits in the Indian coal mining Industry It shows that competency of roof strata and performances of continuous miners are safer, than other coal mining method as well as productive and economical. Continuous miners keep playing a major role in the underground coal mining industry for their safety and as well as their productivity. Regarding past experiences in Indian coalfields, Chirimiri and Jhanjara mines have achieved exceptional performances, with a potential for over 500,000 tonnes per year. Tandsi mine has difficult roof conditions and does not typically achieve high production and productivity. Even so, the difficult roof conditions have been controlled with modern ?world best practice? roof bolting systems and an output of up to 1,200 tonnes per day has been achieved. It can further be emphasized that if this technology is implemented properly it will bring an unfathomable change to the Indian mining scenario. There are many mines in India that may have potential and economic viability with ground control technology concepts for installing continuous miner systems and beginning mass exploitation of underground coal deposits.

Jan 1, 2011

By Roy H. Grau

The trend in underground room-and-pillar cod mining is to employ remote-control continuous mining machines to take extended cuts of 40 A or more. Roof fall safety hazards to the mine worker associated with 4ed cutting are not completely de6ned but are known to include removal of the miner operator from the protective canopy, non-compliance with approved cutting depth and CM operator positioning. This report summarizes ground control research performed by the National Institute for Occupational Safety and Health (?-JIOSH) researchers at the Pittsburgh Research Laboratory concerning extended cuts. A combination of statistical analysis and underground investigations have been conducted. Statistical analysis of extended cut use, along with roof fall accidents and fatalities data delineate the extent of the problem in U.S. coal mines. Additionally, an underground study is described where the long-term roof stability of extended cut areas are compared to standard cuts.

Jan 1, 1997

By Gheorghe Oncioiu

The phenomena developed on the influence of thick coal seam no.3 mining, by horizontal slices and rocks caving roof control, in the Jiu Valley coal basin, are very complex. By analyzing the influence volume of underground faces and defining the stress and strain zones, around the faces, it is possible to evaluate the suitable powered support performances. Also, Jiu Valley thick coal seams involve about 50% of reserve balance in the main safety pillars of social, industrial and natural objectives, situated on the mining surface perimeters. For a correct design and drawing of main safety pillars complex research was done with the aim of establishing the subsidence parameters. Upper face rocks medium could be assimilated as a granular medium, which is in a permanent movement. For describing the rocks movement, respectively the ground surface displacement, was taken into account the stochastic mechanics principles. The theoretical solutions are in accordance within situ measurements.

Jan 1, 1999

By Xiaocen Lu, Guowei Li, Jiantao Wu, Thang N. Nguyen, Andrew C. Amenuvor

"This paper investigates the effect of driving a group of 52 open-ended Prestressed High Strength Concrete (PHC) piles on an existing highway embankment based on field measurements of excess pore pressure and lateral soil displacement. Excess pore pressure due to pile driving increased with depth and decreased with increasing distance from the pile, influencing a distance of 43 pile diameters. For pile groups, the rate of dissipation of excess pore pressure decreased with increasing depth and averaged 79% in 20 days, during which maximum ultimate bearing capacity was not yet attained. Lateral soil displacement continued to increase for a period of time after the end of pile driving and this could have resulted in significant inclination of piles if pile installation was too quick and pile spacing was too small. Lateral soil displacement due to pile group decreased with decreasing distance to the existing embankment as a result of high soil density produced by the embankment loading. The results also indicate that the effect of pile group installation on the existing embankment is negligible.INTRODUCTIONPile driving can cause excessive lateral displacement of soil and heaving of the ground surface, which may adversely affect nearby structures. In addition, lateral deformation and excess pore water pressure resulting from pile driving can exert lateral pressures and vertical forces on the piles, and impact negatively on the project and its surroundings. Therefore, it is important to evaluate the influence of pile driving on the nearby structures as well as the project itself when expansion works are carried out.Recent years have seen some development in the application of field tests for studying soil disturbance due to piles, and these tests usually involves pore water pressure and lateral soil displacement monitoring during pile driving. Results of field experiments performed by Reese and Seed (1957) in San Francisco Bay Mud with instrumented piles showed that pile installation generated large pore water pressures at the pile surface, with only slight increase at a distance of 15 pile diameters away. The measurements indicated that the increase in pore water pressures can exceed the initial total overburden pressure. Holtz and Lowitz (1965) reported a decrease in undrained shear strength immediately after pile installation, which was largely recovered after full pore pressure dissipation for field measurements within 1.5–2 pile diameters from the pile surface. Hwang et al. (2001) presented results of large scale pile driving tests where maximum excess pore water pressure generated decreased rapidly with increasing distance from pile. The excess pore water pressure became negligible at 15 pile diameters from the pile. Their results also showed that lateral displacement of the ground decreased with increasing distance from the pile. Pestana et al. (2002) carried out full-scale closed ended pile tests in the Young Bay Mud deposit. Higher excess pore pressures were observed for points closer to the pile, which decreased with increasing distance from the pile wall. Exponential decay of excess pore pressure with time was also noted. An 80% dissipation of excess pore pressure was achieved for soils more than one pile diameter away from the pile wall between 50 to 80 days. Lateral deformation generally decreased with increasing distance from pile wall, whilst varying erratically with depth. Bozozuk et al. (1978) reported on soil disturbance due to driving of 116 concrete piles in sensitive marine clays in a construction project. Maximum pore water pressures after pile driving within the group, and 6m (20 pile diameters) from the group were over 35-40% of the total overburden pressures, and the influence of pile driving on pore water pressure at 20m away from the group was very small. Cooke and Price (1973) studied a 168-mm-diameter instrumented pile jacked into over consolidated London clay. Outward lateral displacements ranging"

Jan 1, 2016

By Ryan Law

Ground energy systems are being installed in increasing numbers in the United Kingdom. This is particularly true in London where planning regulations require larger scale developments to provide at least 10% of their entire energy demands from renewable sources. A common approach has been to use the groundwater from the Chalk aquifer as a source of energy. This paper explains the potential long and short term sustainability problems with groundwater based systems sited in central London (or any other urbanized area). It also outlines an approach to site testing and numerical modelling to ensure that the system functions well throughout its lifetime. This approach is then applied to a project located in central London.

Jan 1, 2008