Search Documents

By A. J. Rigby

Refractory linings in converters or anode furnaces used to over-oxidize the blister copper will suffer rapid deterioration, due to prolonged contact with copper oxide-rich slag. Nitrogen stirring with COP KIN porous plugs and use of SEMTECH OPC in converters and anode refining vessels can considerably reduce both refractory wear and processing times. In addition, careful control of the vessel atmosphere and the use of real-time optical process control minimize both slag volume and contact time with the vessel refractory.

Jan 1, 2005

By Qingzhu Li

The brewing industry byproduct, spent grain (SG), was evaluated for its ability to adsorb Ag(I) from aqueous solutions. Ag(I) adsorption was dependent on solution pH, contact time, adsorbent dose, initial Ag(I) concentration and temperature. The kinetic data were well described by pseudo-second-order kinetic model, indicating that chemical adsorption was the rate-controlling step. The equilibrium data followed Freundlich isotherm rather than Langmuir isotherm, suggesting heterogenity of the adsorption sites on spent grain. Ag(I) desorbed from Ag(I)-loaded spent grain was also evaluated in this study. HCl, NaOH, Na2S2O3 and ultrapure water were chosen as eluants and desorbed Ag(I)-loaded spent grain for 30min, Ag(I)-loaded spent grain desorbed in 0.1M Na2S2O3 exhibited higher elution efficiency as compared with other eluants. The results indicated that application of spent grain for adsorption and recovery of silver from aqueous solutions was feasible.

Jan 1, 2009

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been investigated on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27 degrees between each tuyere, and five side tuyeres with an angular separation of 22.5 or 27 degrees between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By Tiezheng Li

Keywords: Laminate Composites; Mechanical Behavior; Damage Evolution The mechanical performance of Ti-6-4-Al3Ti metal-intermetallic laminate (MIL) composites synthesized by a reactive foil sintering technique was evaluated. Crack morphology of untested Ti-6-4-Al3Ti MIL composites has been characterized by optical microscopy. Mechanical tests were performed on Ti-Al3Ti metal-intermetallic laminate (MIL) composites and pure Al3Ti, and the principal mechanisms of damage initiation and accumulation were identified experimentally. The elastic properties and anisotropy of the laminates were calculated and successfully compared with Resonant Ultrasonic Spectroscopy (RUS) measurements. The effect of residual stress on the fracture toughness of the Ti-6-4-Al3Ti MIL composites was analyzed.

Jan 1, 2005

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009

By Xiang-yang Zhou

Keywords: Low-Grade Dolomite, Low CaO Content, High Specific Surface Area, MgO. A low energy consumption preparation technology of magnesium oxide with low calcium oxide content and high specific surface area from low-grade dolomite has been investigated. The optimum technical conditions for the preparation of magnesium oxide are the followings: dolomite is partially calcined at 750-800° for 2 h; the optimum solid-liquid ratio range in calcined dolomite slurry is 20-30 g?l?1; carbonation temperature, carbon dioxide pressure and end point pH value of carbonation are less than 40°, 0.4-0.6 MPa and 7 respectively during carbonation process; decomposition temperature of Mg(HCO3)2 solution is near 100°; calcination temperature of the precursor (i.e. precipitated basic magnesium carbonate) is less than 850°. More than 90% of magnesium can be extracted by the technology. The MgO product (CaO < 0.38%) with a specific surface area of near 50 m2?g?1 also can be obtained by the technology.

Jan 1, 2005

By Vladimiros G. Papangelakis

During the past five years, chemical modelling work at the University of Toronto has elucidated the role of soluble magnesium on the autoclave acidity and has demonstrated why feeds rich in magnesium, and other divalent metals, require more than the stoichiometric requirements in acid to produce a leaching performance comparable to that of low magnesium feeds. This understanding has allowed the calculation of acid additions to the pressure acid leach (PAL) on a less empirical basis. Optimizing acid additions to the PAL confers savings in neutralization costs, ensures high productivity and minimises corrosion problems. Hence, our picture of the solution chemistry inside the autoclave during the PAL process has been substantially improved and is reviewed here. Experimental techniques based on solubility and direct acidity measurements that support the theoretical predictions are presented. Concepts of chemical modelling of electrolyte systems at high temperature and software issues are also discussed. Finally, a better understanding of the solution chemistry at temperature has led to better kinetics models because all metal dissolution and precipitation reactions are acid driven and controlled. . Therefore, reactor modelling efforts by our group are also presented and a reactor model with very good performance, as compared to pilot-plant data, is also made here. Finally, in spite of the above success in PAL solution chemistry and reactor modelling, significant challenges lie ahead in theoretical data gaps and instrumentation; these are also discussed in this paper. Keywords: Laterites, process modelling, pressure acid leach, solution chemistry, chemical modelling, reactor simulation

Jan 1, 2004

By Mingming Zhang, Ramana G. Reddy

"Carbon dioxide (CO2) is one of the most common by-products produced during light metals production. It is considered to be the cause of greenhouse effects. Efficient reduction of CO2 can help minimize the rate of global warming and improving energy sufficiency. In this paper, a novel light metal production process was developed using ionic liquid electrolytes. This process has significant advantages compared to the traditional high temperature processes such as zero CO2 and CF4 emission, low energy consumption due to the low temperature operation and nonconsumable electrodes. Two types of anode materials (graphite, extruded carbon) were tested in electrolysis experiment. The results showed that both anode materials were stable (negligible weight loss). However, the extruded carbon was found to be superior to graphite in terms of current density and current efficiency. The calculated energy consumption for aluminum production was less than 10 kWh/kg at current densities up to 300 A/m2.IntroductionGlobal demand for ultra-light, ultra-strong, recyclable metals is growing as the world switches to low-emission vehicles, energy-saving devices and sustainable products. Aluminum demand is forecast to climb by 30 percent; magnesium demand by 200 percent, while for the emerging industrial light metal, titanium, the demand is expected to be at least double in the next decade. However smelting of light metals is the most energy intensive among all the steps of light metals production. For example, on an average it takes about 15.7 kWh of electricity to produce one kilogram of aluminum from alumina [1, 2, 3]. Advancements in energy efficiency have been steady, but slow, and most U.S. aluminum smelting production operates at 95% current efficiency. Besides high energy consumption, another major concern of the light metals smelting process is the emissions of greenhouse gases (GHG). Electrolysis green house gas emissions in the Hall-Héroult process can be split into three groups: 1) reduction reaction emissions, carbon dioxide (CO2) and carbon monoxide (CO); 2) process upset perfluorocarbons emissions; and 3) hydrogen fluoride (HF) formed from the moisture (H2O) present in the raw materials [2, 3]. Hydrogen fluoride gas can be captured and returned to the cells by the alumina dry scrubbing system used in modern facilities. A total of 5.31 kilograms of CO2 is generated from the reduction process for each kilogram of aluminum produced in the average U.S. primary facility. The perfluorocarbon emissions are related to the “anode effect.” If the concentration of alumina in the bath becomes too low, other reactions between the carbon anode and the bath occur and tetrafluoromethane (CF4) and hexafluoroethane (C2F6) are generated. These gases have high global warming potentials (GWP), which is a ratio developed to compare the ability of each greenhouse gas to trap heat in the atmosphere relative to carbon dioxide"

Jan 1, 2008

By Ikuhiro Sumi

A new steelmaking process, in which manganese ore was intentionally reduced, was developed to achieve a higher manganese Yield using a combined blowing converter. In this study, manganese behavior was discussed through the introduction of a model. Apparent reduction rates of manganese were calculated by the two terms that were determined experimentally, with SOkg and 2S0ton combined blowing converters. The model calculated manganese changes during the operation. We applied the model to the actual operation and found that manganese behavior was predicted fairly well by this model.

Jan 1, 1996

By Jae R. Lee

Keywords: Self-propagating high temperature synthesis, AlN, Powder synthesis The particle size and shape effects of starting raw powders on the synthesis of aluminum nitride by self-propagating high temperature technique under high nitrogen pressure were investigated with various AlN diluents and Al reactants. It was found that the structure of beds of the starting raw particles largely affected the pore channels for nitrogen gas infiltration as well as the passages for combustion propagation before and during the reaction, resulting in the morphology and purity changes of the synthesized products. The AlN product of purity over 98% with about 30 microns was obtained.

Jan 1, 2005

By Alaina B. Hanlon

Keywords: Undercooling, Convection, Dendrites, Stainless Steel, Levitation Certain Fe-Cr-Ni stainless steel alloys solidify from an undercooled melt by a two-step process in which the metastable ferrite phase forms first followed by the stable austenite phase. Recent experiments have shown that the lifetime of the metastable phase is strongly influenced by flow within the molten sample. The current research will provide insight to why flow affects the metastable phase. This new understanding will lead to the use of convection to control microstructural evolution in spray-forming of stainless steels. Simulations using a commercial computational fluid dynamics package, FIDAP, yield a range of convective flow velocities that cause mechanical damage to the dendrites which is compared to experimental results. If the convective velocities are great enough that the dendrites bend, then low angle boundaries form at the points of collision. These result in high energy sites that could serve as nuclei for the stable phase.

Jan 1, 2005

By Z. Sun

Magnetic fields have been used for inclusions removal from melt and preparation of materials with gradient compositions. Fundamental in these applications is that the induced magnetic forces on the particles/melt can enhance migration and change the interaction behavior. In the present paper, migration and interaction behavior of electrical-insulating particles in a conductive melt under strong magnetic field are theoretically analyzed. It is found that the migration can be considerably enhanced for micrometer sized particles by applying a strong magnetic field. In addition, two forces are involved in the interaction between two particles: the interparticle magnetic dipole-dipole attractive force due to magnetization and the repulsive force induced by flow of the melt. This theoretical analysis renders a better understanding of recent experimental results. Additionally, a new method by using strong magnetic field can be proposed to control the particle size distribution for the preparation of metal-matrix composites.

Jan 1, 2009

By Zhigang Liang

Investigation into the mixing of 150t ladle furnace by two-nozzle jetting was performed by a water model simulation of 1:4. The effects of nozzle arrangements including separation angle, radial position and asymmetry as well as tracer adding position on the mixing time were studied. The most favorable mixing is achieved when the two nozzles are symmetrically arranged at half radii in the ladle, with 45o separation angle. The empirical relationship between the mixing time and stirring power intensity has been established for two-nozzle jetting based on the present experimental results. In addition, the swelling above bath surface is also investigated with two-nozzle jetting.

Jan 1, 2009

By S. Tanaka

The Tamano Smelter of Hibi Kyodo Smelting Co. Ltd. was commissioned in 1972. Since start up, the anode production capacity has increased from 101,000 tpy to 290,000 tpy, as a result of the application of continuous improvements at each phase of the expansion projects. The Tamano Smelter had developed several innovations, including the original coke combustion technology for Flash Smelting Furnace operations (T-FSF), and has also been able to extend the operating life of the Peirce-Smith converters. This paper will present several improvements implemented at the Tamano Smelter, and will discuss relevant P-S converter operation.

Jan 1, 2005

By Zhenjun Tan, Lei Zhang, Jigang Li, Yifang Zheng, Jilai Xue

"Water electrolysis in 0.4 mol/L NaOH solution for hydrogen generation was carried out with ultrasound introduced through the anode. It was found that the cell voltage reduced by 150-300 mV in the current range of 20 mA to 40 mA with ultrasound frequency at 25.3 kHz. The cell operation became unstable when the cell current was larger than 75 mA with ultrasound. This reduction in cell voltage was due to removal of the gas bubbles on the electrode surface, which can be directly observed in the see-through cell of water electrolysis. Ultrasound with frequency of 33.3 Hz was also tried, but no better effect was obtained. The results suggest that ultrasound assisted water electrolysis can have potential in energy savings for hydrogen production.IntroductionIn electrolytic process, the electrode that the bubbles generated on its surface usually covered a thin gas film, which can be caused an additional voltage about 0.15-0.25V[l,2], especially in aluminum electrolysis. To solve the problem, loading the ultrasound removes the gas bubbles from the electrodes, this subject had been researched in recent years. From 1995 Jilai Xue et al[3,4,5]. applied the ultrasound in aluminum electrolysis in lab. The results from Sheng-De Li et al.[6] reveals that can decrease the cell voltage and have influences about the hydrogen and oxygen's output ratio. Although there are many paper about the applying of ultrasound such as in electrolysis[5,6], deposition[7,8], plating[9,10], oxidation of salts substance on the surface of electrodes[l 1] and so on, the effect of different frequencies ultrasound hadn't been investigated deeply.We focus on the anode voltage by different frequencies ultrasound and the bubble behaviors in this paper. The environment of this experiment is in alkaline solution. Through this exploration it can offer a basis for the applying of ultrasound in electrolysis."

Jan 1, 2011

By G. N. Shannon

Keywords: inclusions, slag, modeling, interfacial energy, capillary force, particle flotation, particle separation A previously introduced model of inclusions separating across a steel-slag interface, developed by Nakajima/Okamura and Bouris/Bergeles, is expanded to include different inclusions shapes (octahedral and plate-like, besides spherical) as well as comparison between model ladle-, tundish-, and mold-slags. Investigation of the relation of these shapes with the interfacial capillary force ? which arises due to the dynamic interfacial energy during separation ? has shown that the force has a significant effect on whether the inclusion separates rapidly or settles at the interface. For the slags considered, the most significant physical property is found to be viscosity, which resulted in fast separation times for inclusions in the mold and ladle slags, relative to the more viscous tundish slag. Particle dissolution (using experimental data) is included in separation modeling.

Jan 1, 2005

By Yoshio Nakano

Keywords: Tannin gel, Palladium, Separation, Redox We have developed the novel recovery system of palladium from wastes, which is simple and generates little secondary waste in comparison with the conventional recovery processes, using tannin gel particles synthesized from condensed-tannin molecules. Pd is adsorbed onto the tannin gel particles through inner-sphere redox reaction mechanism: two-electron transfer from tannin gel to Pd(II) species, accompanied by ligand exchange between chloropalladium(II) complexes and tannin molecules. In addition, we propose the separation system of Pd and Au from Pd-Au mixture, which is feasible due to the difference in oxidization and reduction potential between Pd and Au species: PdCl3(H2O)? and PdCl42? are less adsorbable than Pd species containing fewer Cl, such as PdCl2(H2O)2 and PdCl (H2O)3+, while such a distinct difference between Au species is not observed.

Jan 1, 2005

By Pengfu Tan

A program ?SlagVis? has been developed to simulate the liquidus temperature, phase compositions and viscosities of ZnO-CaO-SiO2-Al2O3-?FeO? slag, such as Imperial Smelting Furnace (ISF) slag and lead blast furnace slag, combined with F*A*C*T slag database and the mathematical model of slag viscosities based on a modified Urbain formalism. The modeling results have been validated by a number of measurements. The effects of slag compositions on viscosities of ISF slag and lead blast furnace slag have been simulated and discussed.

Jan 1, 2005

The high pressure acid leach process (HPAL) is being commercially used in four plants around the world to treat limonitic laterites. The two major operating costs of the HPAL process are the sulphuric acid and the energy required to heat the pulp to the desired temperature (>240°C). As an alternative to acid injection and steam heating, the in-situ generation of sulphuric acid and heat, produced during the high temperature pressure oxidation of sulphur-bearing materials blended with laterites, has been investigated at the laboratory scale. Various sources of sulphur have been examined, in particular, elemental sulphur, pyrrhotite and a Cu-Ni low-grade bulk concentrate. Under the proper blend ratios, all sulphur sources tested generated sufficient acid to result in equivalent nickel and cobalt dissolutions. A significant improvement to the process economics can result from the addition of sulphur sources containing valuable by-products, such as nickellcobalt andlor precious metals (gold and PGMs). This is especially true in the latter case, when the HPAL can be operated under Platsol conditions (i.e. with the addition of 5-10g/L of chloride), to dissolve the base metals and precious metals simultaneously in the autoclave. Various examples of the application of this concept are presented, together with a brief discussion of its implication on the autoclave design and the downstream processes to recover the values from the leach solutions. Keywords: limonite, co-treatment, acid consumption, sulphur, sulphur compounds, pressure acid leach (HPAL, PAL), Platsol process

Jan 1, 2004