Search Documents

By Richard W. Lawrence

Leaching of copper from sulfide minerals using biooxidation offers a potential route for copper recovery. Oxidation of . sulfide sulfur can proceed either; to sulfate or to elemental sulfur depending on mineralogy and process conditions. The advances in commercial application of biooxidation for sulfidic gold ores has made available operating and cost data which allow the derivation of conceptual costs for copper ore processing for comparison with conventional processing routes. Although costs for copper biooxidation generally remain high relative to conventional smelting, application might be competitive in specific cases. Biooxidation becomes more competitive in the general case if the cost ofS02 emissions in pyrometallurgical processing were to be internalized to a greater degree than currently required. This paper describes the technical aspects of biological processing of copper sulfide ores and concentrates, specifically with respect to the fate of sulfur. The environmental and economic implications of the biooxidation route are discussed in relation to conventional processing.

Jan 1, 1996

By R. Steven Izatt

Green chemistry principles will be discussed, and examples will be given of the use of Molecular Recognition Technology (MRT) to selectively separate specialty metals such as cobalt, nickel, bismuth, rhenium, molybdenum, indium and germanium from various primary and secondary feed streams. Recovery of these metals has numerous advantages including (i) conservation of valuable resources, (ii) prevention of environmental damage, and (iii) elimination of capital and operating expenses due to re-processing or disposal of metal-bearing streams.

By Sarah Beutner Mavrogenes

The mineralogy of three slags from a domestic secondary copper refinery were studied by applied mineralogical techniques to determine the: 1) phases present, 2) phase chemistry, 3) phase abundance, 4) associations, 5) crystalline habit, 6) grain size, 7)microtextures, and 8) causes for certain metallurgical problems, such as metal losses to the slags. The slags were produced by skimming the bath prior to melt-down to allow heat from the flame to reach the bath. The first slag is highly viscous and all three slags contain a large amount of copper. The "first slag", which is skimmed prior to treatment of the bath with fluxes, contains metallic copper, cuprite, delafossite, magnetite, Mg-hercynite, common spinel-chromite solid solution, picrochromite-chromite solid solution, common spinel-picrochromite solid soiution, gahnite, cassiterite, silica-rich glass, and corundum. Its abundant solid refractory phases make the slag difficult to skim. The "soda-rich slag", skimmed after the treatment of the bath with sodium carbonate flux, contains cuprite, delafossite, magnetite, cassiterite, Na-Al-silicate, and Na-Al-Ca-silicate. It contains less metallic copper than the first slag and lacks the refractory minerals. The "phosphorus-rich slag", skimmed after treatment of the bath with a copper phosphide flUX, contains metallic copper, cuprite, delafossite, berlinite, cassiterite, silica, apatite, Cu-Fe-rich apatite, copper phosphate, Cu-Fe-phosphate, and a Pb-phosphate. In contrast to the above three copper-rich slags, recent charges have produced a silver-copper-rich slag. The "silver-rich slag", skimmed after the treatment of the bath with a copper phosphor ide-borax flux, contains, cassiterite, delafossite, cuprite, a Na-Al-silicate, magnetite, metallic copper, MgO, common spinel-chromite solid solution, and wollastonite. Silver ranging from 0.05 to 2.02% was found by atomic absorption and inductively coupled plasma spectrometry analyses in the metallic copper phase.

Jan 1, 1989

By R. P. King

The essential features of an image analysis system for the measurement of mineral liberation are described. Good procedures for image acquisition and image processing prior to image analysis are defined. The basic stereological methods for the measurement of volume fraction, surface area per unit volume, particle size distribution and liberation spectra are given. The appropriate methods for fractal correction when measuring perimeters of irregular features and for frame correction when measuring linear intercepts are developed. Practically useful and accurate procedures for the stereological correction of particle size and liberation distribution methods are given.

Jan 1, 1995

By H. J. Roorda

With an increasing need to obtain metals by processing complex fine intergrown ores, the use of electron-optical techniques will become more important as a tool for mineralogical studies. Electron images enable a higher spacial resolution than can be obtained by optical microscopy and thus provide a powerful and necessary aid for the examination of small grains and finely locked particles. In this paper the mineralogy of Meggen ore was investigated. Both light-optical and electron-optical techniques were used to evaluate the mill feed and products of the concentrator. Detailed examination by reflected-light microscopy to assess the comportment of galena in the complex pyritic ore was inconclusive in establishing the cause for low lead recovery of only forty percent of the ore's lead content. Electron microprobe analyses indicated that the majority of the lead lost to the tailings was accounted for by extreme fine (often smaller than one micron) and complex intergrowths of galena in pyrite. The remainder was lost as fine free galena grains.

Jan 1, 1987

By Von L. Richards

Rapid Freeze Prototyping (RFP) is a novel solid freeform fabrication technology that creates parts by depositing water droplets and freezing them rapidly to form layers. An investigation into the smallest thickness that can be achieved by the RFP process was conducted. The factors that could significantly affect the thickness of the part built by this process including substrate temperature, volumetric feed rate, table velocity, nozzle frequency, nozzle standoff distance, and head pressure were considered. A shell building technique for use with the RFP system has been developed. Thin wall ice patterns have been invested using production shell building techniques and an alcohol-based slurry. The finished shells were quantitatively evaluated by inspecting their total shell thickness, mold cavity dimensional reproducibility, and shell strength. Pattern loss is influenced by not only the alcohol / water interaction but also the starting thickness as it relates to thermal mass.

Jan 1, 2008

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transfonnation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling.

Jan 1, 2003

By Ali S. Al-Watban

"In this paper, the room temperature friction and deformation properties of various polycrystalline diamonds; i.e. aggregates of diamond crystals with a ""binder"" phase of cobalt and a polycrystalline coating produced by a chemical vapour deposition processes (CVD) were studied when softer metallic and ceramic sliders were used. The experiments were conducted· at relatively low sliding speeds (10 mm/min), in a vacuum of 10-5 mbr after having cleaned the specimen surfaces by out-gassing them for about 30 min at 800 °C. As a result of increasing the number of traversals significant wear of the coated diamond by softer metallic sliders (aluminium and mild steel) was observed. With ceramic sliders, it is shown that the multiple traversals result in the formation of wear groove. With diamond silicon carbide, high friction and adhesion lead to significant metal transfer which then pre-empts cumulative deformation of the harder materials. With the diamond-cobalt composite, the friction is surprisingly low, there accumulation of wear debris on the tip of the slider but no permanent transfer of metal and the harder specimen is not damaged even after 5000 traversal.IntroductionPolycrystalline diamond is mainly produced as tool materials for the machining of hard metals and composites. Thus, the sliding friction and wear resistance are amongst the most important properties relevant to those applications.During cutting by PCD the wear mechanism is mostly influenced by the chemical affinity between the tool material and the workpiece. For example, diamond based materials are not recommended for machining ferrous materials because carbon is highly solubie in iron: This leads to the graphitisation of diamond particles and hence a high rate of diffusion wear is observed (Brookes and Lambert, 1982)."

Jan 1, 2000

By Jürgen Antrekowitsch, Thomas Griessacher

"Heavy metal containing residues are typically hazardous wastes because on the one hand, a deposition gets more and more complicated and on the other hand, the large amounts of metals like Zn, Cu, Fe and Pb represent a significant value. Thus, a post-treatment of these materials with the recovery/recycling of the metals and stabilization of the waste is not only ecological but often also economical. The therefore typically applied recycling processes utilize pyrometallurgical steps, where carbon or carbon monoxide from fossil coal and coke is used as a reducing agent, which results in large amounts of CO2 emissions. An alternative option is the application of a hydrogen-rich gas emitted in biomass utilization processes as a carbon-neutral reducing agent. Investigations in a retort process which were done at different temperatures and times showed excellent results concerning the achievable reduction rates and final contents of the heavy metals for various residues.IntroductionNowadays heavy metal containing residues like electric arc furnace dust (EAFD), dust from cupola furnaces, waelz slag, etc. are declared as hazardous wastes in a growing number of countries due to the leachability of the heavy metals in these residues. For that reason it is no longer possible to landfill these materials or use them for road construction or disposal works. Some land filling activities, carried out until now, have only been realizable because of some process modifications or cost intensive post-treatment steps of these residues. But the disposal capacities for such materials are decreasing, therefore increasing the prices. The second point for the growing disposal limitations is the stringent environmental legislations and regulations, which restrict the number and amounts of materials which can be dumped [1 – 5].From the other point of view these heavy metal containing residues usually have high contents of zinc, lead, iron, etc., which represent a significant value and therefore a big potential to recover these metals. This is why in recent years the number of recycling processes and the amount of recycled heavy metal containing residues have continuously increased. These recycling processes have the target to recover the valuable metals from the residual materials in the form of a saleable product as well as the stabilization of the slag produced in these processes [5, 6]."

Jan 1, 2011

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transformation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling

Jan 1, 2003

By G. S. Hill

A large amount of the stereological error associated with liberation studies can he eliminated by assessing areas instead of linear intercepts. The presentation of a simple geometrical model as a stereological 'worst case' allows calculation of the worst possible grade/recovery curve for a given assemblage of areas. The true results are expected to lie in the window between this worst case and the hest possible case, represented by uncorrected data. The width of this window typically corresponds to an error margin of about 5% grade at a given recovery. An indication of where the data lies within the range of possible grade/recovery results may he obtained from a qualitative analysis of the locked section complexity. Assemblages consisting of texturally complex locked sections (ie. containing many mineral nuclei) are likely to exhibit minimal stereological bias and therefore will tend to lie close to the uncorrected side of the grade/recovery window.

Jan 11, 2011

By Richard S. Kunter

Artech Recovery Systems, Inc has developed a low pressure and temperature? leach process called the "Cashman Process" to extract metals from arsenical flue dusts and residues and fix the arsenic in an environmentally stable form as ferric arsenate (scorodite). The process was pilot tested at Hazen Research in an integrated plant including continuous recycle from August 1989 to October 1989 during which several tons of flue dust were processed. Based on this pilot program, the process was deemed technically feasible and produced commercially salable products. Residues from this pilot program were subjected to a long-term stability test jointly designed by PTI environmental services and the USEPA. The process, its versatility, and the nature of the products is discussed in some detail.

Jan 1, 1992

By G. E. Lagos

This paper analyses the scope and instruments employed by the Basel Convention for regulating the transboundary movement of hazardous wastes, the present and projected hazardous waste regulations of Chile, reviews the Chilean import/export trade of wastes of the period 1985-1995, and discusses, the influence that the Basel Convention has had on mining trade, its perceived benefits and costs, and possible effects on Chile's trade of the application of the Convention's Decision III/l. There is no quantitative estimation as to the effect of the Convention on the general volume of imported or exported materials destined for recovery, recycling, reclamation, or reuse. All recycling imports, with the possible exception of residues of petroleum oil, which occurred during the decade 1985-1995, can be classified tentatively as non hazardous. The entry into force of the Convention has had several effects on Chile's trade. It has brought home the need to have a comprehensive hazardous waste legislation, it has been a base for applying import restrictions, which in all likelihood, would .have otherwise not been applied, The benefits and costs of this import restriction, as well as those of the multilateral export ban are analyzed.

Jan 1, 1999

By M. J. Adam

As part of its research programs, the Bureau of Mines is investigating the partitioning of complex sulfide minerals to simpler sulfide phases by sulfidation reactions. Partitioning in this manner can afford opportunity to improve selective extraction of mineral constituents of value. This report describes research involving the sulfidation partitioning of the mineral pentlandite, which is an important source of Ni in primary production. For the laboratory studies, the pentlandite was synthesized in nominally equiatomic proportions of Ni and Fe. Elemental Ni, Fe, and S powders were blended, compacted, and sealed under reduced He pressure in vitreous silica tubes. The tubes were heated under controlled conditions at SOD? C for 24 h. The product was verified by X-ray diffraction and chemical analysis to consist essentially of (Ni,Fe)9S8. Small samples of the (Ni,Fe) S were encapsulated with sulfur in silica tubes at reduced He pressures and heated for 1 to 24 h at specific temperatures between 400? and 600? C, both below and above the boiling point of sulfur (_445° Cl. Reaction rate increased with temperature. Within this temperature range, partitioning to individual Ni and Fe disu1fides proceeded to essential completion according to the reaction

Jan 1, 1988

By M. Shevchenko

Integrated experimental and modelling research program on the phase equilibria and development of thermodynamic databases of the lead and copper metallurgical gas/ slag-matte-metal-solids systems (PbO-“Cu2O”-FeO-Fe2O3- ZnO-CaO-SiO2) is being undertaken to support improvements in the pyrometallurgical smelting and recycling processes. This is the first systematic investigation of phase equilibria of slag systems in equilibrium with Pb metal, providing information for systems in which copper coexists in slag with lead or zinc as major components. The experimental studies involve high-temperature equilibration of synthetic samples, rapid quenching, and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). FactSage-based thermodynamic database development is integrated with experimental research. Initial thermodynamic assessments are used to identify priority compositions and conditions for experiments, which are planned to provide specific data to assist thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved. Continuous database improvement and extension to include new elements are targeted. Example of industrial application is given.

By P. Ret, E. Üstiindag, R. Dieckmann, R. Subramanian, S. L. Sass

"Partial reduction reactions in the Ni-AI-O system, starting with the spinel compound NiAI20 4, are used to form metal-ceramic microstructures. By suitable choice of processing parameters, such as reduction temperature, oxygen partial pressure and time, two different morphologies of nearly pure Ni particles, equiaxed and rod-like, form within a ceramic matrix, which is either a-A12O3 or a metastable ""defect spinel"". Electron microscopy studies were performed for microstructural characterization, phase identification and chemical analysis. The fracture toughness of the Ni-AI2O 3 mixture was significantly improved with respect to that of the original spinel phase. The important issues that must be addressed to form useful metal-ceramic microstructures by partial reduction reactions rue discussed. It is shown that cracking at the original spinel grain boundaries, likely due to the large volume changes associated with the reduction reaction, can be avoided by the addition of small amounts of ZrO2• Initial results illustrating effect of ZrO2 on the microsuuctures are presented.IntroductionEngineering materials used in load bearing circumstances, particularly under extreme conditions (e.g. high temperatures or stresses), generally are formulated with complex microsuuctures. Such composite-like materials can possess properties unobtainable by either of the individual constituents. With metal-ceramic composites, for example, a material can be obtained with an optimum combination of the low density and high strength of the ceramic, and the toughness of the metal. For high temperature service, where demanding conditions are often present, for example, inside jet turbine engines, a successful new material must have low density, high Young's modulus as well as good oxidation resistance, strength, fracture toughness, creep and fatigue resistance. The candidates include intermetallic compounds, and metal-ceramic, intermetallic-ceramic and ceramic-ceramic composites."

Jan 1, 1994

By G. S. Hanumanth

Sedimentation of particles during the liquid metal processing of particulate metal-matrix composites can affect the homogeneity, and thereby the properties, of the cast product. A novel electrical probe has been developed to measure the in-situ volume fraction of ceramic particles in molten metal baths. Using this probe, sedimentation rates for 90 pm silicon carbide particles dispersed in molten aluminum A356 alloy were measured over a wide range of particle volume fraction, 0.05 to 0.3. The sedimentation rate was found to depend strongly on particle volume fraction; the time to clarify a 0.15 m depth increased from approximately 60 to 500 seconds as the volume fraction increased from 0.05 to 0.3. Measured sedimentation rates agree well with the predictions of a sedimentation model based on one-dimensional, two-phase flow theory in which the inter-phase drag function is derived from the momentum equation, utilizing the Richardson-Zaki Equation for sedimentation in aqueous systems. The implications for solidification are discussed.

Jan 1, 1993

By T. Sakaguehi

Some attempts were made to recover and remove of uranium that may be present in refining effluents, mine waste Water, and other waste sources by using microbial biomass. To establish which microorganisms accumulate the most uranium, 135 species of microorganisms (42 bacteria, 26 yeasts, 34 fungi and 33 actinomycetes) were screened. Of these 135 species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stuzeri, Neurospora sitophila, Streptomyces albus and Streptomvces viridochromogenes. In addition to the research on uranium uptake, thorium recovery by using microorganisms was investigated. High abilities were found in Streptomyces levoris and Bacillus subtilis. The selective accumulation of heavy metal ions by various microorganisms has also been examined. Uranyl, mercury and lead ions were readily accumulated by almost all of the species of microorganisms tested. Actinomycetes and fungi differ from many bacteria and most yeasts in their selective accumulation of uranium, and mercury. The basic features of uranium uptake by Streptomyces viridochromogenes, a microorganisms with high uranium-uptake ability, were investigated systematically. Synthesizing these results, we suggested that the accumulation of uranium into these microbial cells is not directly mediated by any metabolic process:, but almost completely dependent upon physicochemical adsorption on the cell components. In addition to this fundamental research, uranium recovery was investigated in immobilized Streptomyces viridochromogenes. These immobilized cells adsorbed, uranium readily and selectively. The immobilized cells recovered uranium almost quantitatively and almost all uranium adsorbed was desorbed with 0.1 N Na2CO3, These results showed that microbial cells are more stable after Immobilization and can be used repeatedly for the process of uranium adsorption-desorption. These results suggested that these microbial cells can be used for the recovery and removal of nuclear fuel elements, such as uranium and thorium, from refining effluents and mine waste water.

Jan 1, 1991

By Miller, Geoffrey W.

The Ravensthorpe Nickel Project (RNP) flow sheet provides for the upgrading of Ni & Co in a size based beneficiation process prior to leaching. The upgrading effect on Ni and Co makes the beneticiation process a powerful addition to the flow sheet. Multiple linear regression (MLR) analysis based on 351 individual batch tests, 52 large scale composites and 21 pilot plant tests has been used to successfully model beneticiation product grade, recovery, upgrade and mass recovery. Statistically, 83% and 96% of the variability in nickel recovery and nickel product grade respectively was accounted for. Algorithms have been developed for Ni, Co, Mg, Al and Fe, which represents the revenue and operating cost factors for the process. The algorithms have subsequently been applied to the resource model, allowing prediction of elemental grade and recovery for the development of the mine schedules based upon these parameters and not head grades alone. This has allowed optimisation of the mine schedule for improvement to the project's NPV. Keywords: Ni Laterite, Prediction, Multiple Linear Regression, Beneficiation

Jan 1, 2004

By P. M. Swash

The determination of the heavy minerals in beach sand samples is highly dependent on the preparation technique used. In this paper a simple reproducible method for the quantification of "recoverable" ilmenite, zircon, rutile and leucoxene by magnetic separation, is described. The procedure recommended yields information relevant to the metallurgical processing of the ore rather than to the total heavy minerals present in the samples. Finally the determination of mineral reserve estimations and grade assessments is greatly facilitated when this "mineral assay" method is employed. An assortment of other mineralogical methods are described including SEM, EMPA, XRD, XRF, Image analysis, Mossbauer. clerici and perm roll separations. The methods are briefly examined and the practical information that can be gained by using such techniques are reviewed. Experience has shown that an understanding of the relationship between the physical and chemical properties of the heavy minerals can contribute to the prediction of mineral particle behaviour. Such information may ultimately help reduce the prospect evaluation period and minimise expenditure on metallurgical testwork.

Jan 1, 1991