Search Documents

By Manuel Alvarado, David Nemir, Jan Beck

"Thermoelectric generation using special N-doped and P-doped semiconductors is well known as a means for direct heat energy to electrical energy conversion without the need for moving parts. The technology is used today in niche markets for low level electricity production and has been proposed as a scalable means for capturing large scale energy from waste heat streams. The choice of geometry of the thermoelements and conductors is critical to the successful implementation of a waste heat recovery system in order to manage losses due to Joule heating and diffusive heat flows. This paper describes a simulation study to define the performance impact of different aspect ratios for the active thermoelements and the electrical interconnect. The use of a finite element model that incorporates the intercoupled heat and electrical energy flows highlights some of the issues impacting scalability.IntroductionThermoelectric phenomena arise out of the intercoupled electrical and thermal currents in a material. A two-element thermoelectric generator is depicted in Figure 1. It is constructed by connecting an N-type thermoelement and a P-type thermoelement in electrical series, with both elements in thermal parallel between a heat source and a heat sink. The electrical series connection is made by attaching conductors as shown. Ideally, these series connection elements will be both good thermal conductors and good electrical conductors.The two element generator in Figure 1 is disposed between two thermal reservoirs: the heat source, which furnishes heat energy; and the heat sink, which absorbs heat energy. Heat energy flux Q, flows from the heat source to the heat sink, driven by the temperature difference between the source and the sink. As depicted in Figure 1, when a resistive load, R, is attached, electrical current, I, may be extracted from the thermoelectric generator and furnished to the load. The N-type and P-type thermoelements, are the active portions that do the actual conversion of heat energy to electrical energy. Although thermoelements may be built using conductors such as bismuth and antimony, higher efficiency thermoelectrics are built using heavily doped semiconductors. Thermoelectric devices are generally formed by connecting many pairs (couples) of N and P type thermoelements in electrical series and in thermal parallel. A commercially available module having 127 couples (254 elements) is shown in Figure 2."

Jan 1, 2011

By K. Fagerlund

Methods for simulation of settler reactions, matte-slag separation and matte settling in copper flash smelting have been examined. The reaction, separation and settling phenomena of slightly oxidized chalcopyrite samples and cuprous sulfide-magnetite mixtures in fayalite type slags were examined at about 1300°C under inert atmosphere. Two methods based on introduction of molten samples of oxidized chalcopyrite concentrates or synthetic matte-magnetite mixtures onto the surface of molten iron silicate slag were tested. In the first method the samples were water quenched and polished specimens were studied and analysed using light optical microscope, scanning electron microscope, energy dispersive spectrometer. In the second method processes taking place after the introduction of samples onto the slag are followed "in situ" using X-ray transmission image monitoring. Great differences were observed in separation and settling behaviour of low and high grade copper mattes produced as a results of interaction of initial samples and slag.

Jan 1, 1997

By K. G. Wang, M. E. Glicksman, P. Crawford

"We formulate the mathematical solution to late-stage multi particle diffusion in finite systems. The transition from finite system behavior to that for an infinite system is established. Large-scale simulations are reported regarding the dynamics of phase coarsening. Even in the case of a small volume fraction (Vv = 10-4), the particle size distribution is broader than that for the well-known Lifshitz-Slyozov limit at zero volume fraction. We also report the first simulation studies of extremely low volume fraction, for which corresponding experiments, as well as other simulations, do not exist at present for comparison. However, in the case of moderate volume fractions (Vv = 0.1), the fiucutations in the volumetric growth rate of particles are extracted from our simulations. These simulations provide additional insight into the statistical nature of diffusion interactions, including multiparticle stochastics during microstructural evolution.IntroductionPredicting microstructure evolution in alloys remains one of the cornerstones of materials science. Phase coarsening is a common process in microstrucural evolution that leads to a decrease in the excess total interfacial energy of the system. The system typically consists of separate and identifiable units, or domains, such as second-phase particles distributed in a matrix. During phase coarsening, larger particles grow at the expense of small particles. Over time, this ""competition"" results in an increase in the average size of the particle population, and in a concomitant decrease in the number of particles.Particle size and microstructure of many cast alloys depend on similar coarsening processes. Indeed, properties of these materials, such as strength, toughness, ductility, and electrical conductivity, depend on the material's average particle size and particle size distribution (PSD). Understanding and controlling microstructures in two-phase systems are clearly of widespread technological importance."

Jan 1, 2001

By Yuchun Wang

In principle, supported liquid membranes could be an exceedingly elegant separation process. However they tend to fail by displacement and emulsification of the organic solution in the pores, which allows mixing of the feed and strip solutions. We have stabilized supported liquid membranes comprising moctylamine in nylon and PVDF supports by covering the pores with semi-permeable polyamide films, using an in-situ polymerization technique. Scanning electron microscopy demonstrates that the polyamide films are sensitive to production conditions and the nature of the support. The transport properties of stabilized supported liquid membranes for Cr(VI) are compared with those of unstabilized membranes.

Jan 1, 1998

By K. Osseo-Asare

It is possible to form a two-phase system in certain polymerlinorganic salt/water mixtures, such as those containing the polymer polyethylene glycol (PEG). Such aqueous biphase systems have many of the separation characteristics of conventional solvent? extraction systems, but are environmentally friendlier. Just like the well-known organic solvent/water two-phase system, the top polymer-rich phase is more hydrophobic. and the bottom salt-rich phase more hydrophilic. The partition of dispersed? particles is dependent on the interfacial interaction between the particles and the conjugate aqueous biphase solutions. In particular, the hydrophilic/hydrophobic properties of the surface determine the transfer of the dispersed particles into either the top (more hydrophilic) phase or the bottom (more hydrophobic) phase. Accordingly, differences in the surface chemistry of particles can be exploited to achieve selective separations. In this work, several approaches to separation control will be discussed. using pyrite (FeS2), alumina (AI203). hematite (Fe203), silica (Si02), and titania (Ti02) as model particulate materials. For metal sulfides, pH and redox potential can be used to alter the hydrophobicity/hydrophilicity of the particles. In ?the case of oxides. polymer adsorption and collector adsorption may be exploited to facilitate particle transfer.

Jan 1, 1999

By Mark Cross, Hadi Abou-Chakra, Nicholas Christakis, Mayur K. Patel, John Baxter, Ugur Tiizful

"In recent years significant effort has been put into using continuum mechanics for the description of granular flows. Although these models are partially successful in capturing some flow characteristics, they lack essential information on material properties, which are needed to account for the interactions between different particles. Thus, they are incomplete and can not be used to describe processes such as hopper filling/emptying and pneumatic conveying, where particle-particle interactions can lead to phenomena such as segregation, degradation and agglomeration. In this paper, a 3-D unstructured finite-volume framework is presented, which employs interface tracking techniques to solve for the individual material components of the granular mixture in the bulk and thus, determine the material-air interface. Various transport processes, arising from the micro-mechanical properties of the different particle species in the granular mixture, can be obtained through kinetic theory. The transport coefficients of each of the individual species can be determined and analysed in a micro-mechanical framework and the transport process parametrised in the form of constitutive models. These models provide the continuum theory with information on the micro-mechanics.This work describes the continuum framework and the micro-mechanical parametrisations, which are used to describe the processes and interactions at the microscopic level. Numerical simulations and comparisons with experimental data are then presented for the case of binary granular mixtures and conclusions are drawn on the capability of the model to realistically predict and quantify the main characteristics of granular flows."

Jan 1, 2001

By Yoichi Takeda

The CaO-FeOx-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By Keith Rozenburg, Ivar Reimanis, Jesus Chapa

"Experiments in conjunction with finite element analysis (FEA) are used to better predict crack propagation in ductile/brittle graded composites. Cu/W graded composites were fabricated by stacking discrete layers of powders and hot pressing. Crack propagation was studied by loading a notched beam in four point bending and examining the subsequent crack deflection. The notch was placed within a particular composition of material, oriented in a direction perpendicular to the gradient direction. Elastic and plastic mismatch between different constituents in the graded composite induce shifts in the phase angle of loading, thereby causing the crack to deflect. FEA indicates that thermal residual stress has a negligible ""influence on the crack path. The combined FEA and experimental results suggest that elastic mismatch is the single most important material property-related factor in controlling crack deflection.IntroductionMany 'applications would benefit or may even require materials whose performance or functionality must vary spatially. While the concept of functionally graded materials has existed for nearly one hundred years, it is only within the last fifteen years, that research efforts have focused on generic issues in processing, properties and performance of functionally graded materials. This generic research effort has brought together scientists and engineers from traditionally different disciplines to address common issues with graded composites. The current work focuses on issues in structural joining. A wide variety of applications require some type of joining between dissimilar materials. Examples include thermal barrier coatings for turbine engines, wear resistant coatings for tools, ceramic engine parts, and microeiectronic devices, as well as many traditional applications involving metallic welding. The joints may either be discrete, involving a single interface, or they may· be spatially graded in composition. Extensive theoretical and experimental information exists on discrete bimaterial and trimaterial joints, but relatively little exists for graded joints or composites"

Jan 1, 2000

By Deming Wang, R. A. Overfelt

"The oscillating cup viscometer has become a dominant technique to measure the viscosities of high temperature molten metals. Unfortunately, the viscosity estimation model from the observed logarithmic decrement and period of the oscillation is very complicated. There are still large discrepancies of viscosity estimation values between using different measurement facilities and using different viscosity estimation models for a same molten metal. The purpose of the paper is to evaluate the accuracy of an oscillating cup viscometer in Auburn University. Two well known viscosity estimation models, Roscoe's and Torklep's equations, are compared and discussed. The theoretical literature for the fluid flow inside an oscillating cup is reviewed and a more accurate working equation for the Auburn oscillating cup viscometer is developed. Some design parameters of the oscillating cup viscometer, which directly affect the accuracy of viscosity estimation by using the working equation, are discussed. In addition, applications and experimental measuring data are presented in the paper for several different commercial alloys, such as aluminum alloys: A319, A356 and A201, nickel-base super alloys: In713 and In718, and casting irons, C40 Gray Iron and Ductile Iron.1 IntroductionThe oscillating cup viscometer is the most important and has been most frequently used in viscosity measurement for high temperature liquids [1-4]. The principal advantages of this technique over others are its mechanical simplicity and the ability to measure the time period and amplitude decay with great precision. In the viscometer, a high temperature liquid (such as a molten metal) is contained within a crucible suspended by a wire to form a torsional pendulum, which induces torsional oscillation motion. This motion is damped primarily by viscous dissipation within the viscous liquid inside the cup. The viscosity of the liquid can be calculated by an analytical or numerical solution ofthe equations of motion of the oscillating cup system."

Jan 1, 2001

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By S. Neogy, M. Gupta, D. Srivastava, V. Kain, S. Roychowdhury, R. C. Prasad, G. K. Dey

"Austenitic stainless steels are an important material of construction for Boiling Water Reactors (BWR). These stainless steels are amenable to strengthening by strain hardening. Various deformation modes at different test temperatures and strain become active. In the present investigation type 304LN stainless steel was used in the annealed and strain hardened condition. Thin foils were prepared from gauge section for transmission electron microscope (TEM) investigation after tensile testing at room temperature and at 288°C. TEM investigation reveals that twinning is the major mode of deformation for the tests done at room temperature while dislocation cross-slip is the major mode of deformation at higher temperature. Stacking faults were also observed to a limited extent. The extent of twinning was much higher for the tests done using the rolled material. The formation of martensite in the stainless steel due to straining was investigated by the analysis of selected area diffraction patterns.IntroductionAustenitic stainless steels (type 300 series) are an important material of construction in Boiling Water Reactors (BWR). These stainless steels cannot be heat treated but can be strengthened by cold working [1]. Nitrogen alloying of these stainless steels result in high strain hardening rates and higher strength without any loss in toughness [1]. Stress Corrosion Cracking (SCC) in BWR of these types of stainless steels have been attributed to surface strain hardening and strain hardening ofregions adjacent to constrained weldment [2].The test temperature [3, 4], prestrain [5] and nitrogen level [5] has been reported to affect the deformation mechanism during tensile testing. Byun et al. [3] have reported the formation of martensite, dislocations, stacking faults and twinning during tensile deformation, the extent of each depending on the test temperature. Strain localisation has been reported to occur during tensile deformation in irradiated stainless steels [ 6]. The behaviour of rolled material during tensile testing is similar to that of irradiated material to a large extent [3]. Austenitic stainless steels are low stacking fault energy (SFE) materials in which various types of microstructures have been reported to form during tensile deformation and the strain is also highly heterogeneous in nature in these stainless steels which aides SCC in BWR environment to a large extent [7]. During cold working of austenitic stainless steels second order twinning has also been reported [8]. Knowledge about the deformation mechanisms operative in the strain hardened austenitic stainless steels during tensile testing at different temperatures is essential to understand the material deformation behavior and the present study aims at enhancing the existing understanding."

Jan 1, 2011

By J. Leon-Torres, D. M. Stefanescu, P. A. Curreri, S. Sen

"Experiments were performed under terrestrial gravity (lg) and during parabolic flights (10·2 g) to study the solidification and macrosegregation patterns of Al-Cu alloys. Alloys having 2% and 5% Cu were solidified against a chill at two different cooling rates. Microscopic and Electron Microprobe characterization was used to produce rnicrostructural and macrosegregation maps.In all cases positive segregation occurred next to the chill because of the shrinkage flow, as expected. This positive segregation was higher in the low-g samples, apparently because of the higher heat transfer coefficient.A 2-D computational model was used to explain the experimental results. The continuum formulation was employed to describe the macroscopic transports of mass, energy, and momentum, associated with the solidification phenomena, for a two-phase system. The model considers that liquid flow is driven by thermal and solutal buoyancy, and by solidification shrinkage. The solidification event was divided into two stages. In the first one, the liquid containing freely moving equiaxed grains was described through the relative viscosity concept. In the second stage, when a fixed dendritic network was formed after dendritic coherency, the mushy zone was treated as a porous medium.The macrosegregation maps and the cooling curves obtained during experiments were used for validation of the solidification and segregation model. The model can explain the solidification and macrosegregation patterns and the differences between low- and high-gravity results."

Jan 1, 1999

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX!EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 2000

By Sheng-li Wu, Guo-liang Zhang, Bo Su

One of the major challenges for the Canadian Gen IV Super-Critical Water-cooled Reactor (SCWR) concept is the selection of fuel cladding materials. The Canadian SCWR concept will operate at a core outlet temperature of 625 oC and 25 MPa of pressure with peak cladding temperature reaching as high as 800 oC. Corrosion resistance is an important factor for material selection. Austenitic stainless steels that contain Cr contents greater than 18 wt.% are generally considered to provide adequate corrosion resistance. In this work, the pressure dependence of the corrosion of austenitic stainless steel 310 containing 24 wt% Cr is assessed at 625 C for exposures of 1000 hours to evaluate the suitability of superheated steam as a surrogate for supercritical water at 25 MPa. Transmission Electron Microscopy (TEM) revealed that 310 exposed to different pressure conditions at 625 oC. (i.e., 0.1, 8 and 29 MPa) had generally the same type of the oxide structure, i.e., a Cr-rich oxide with the spinel structure on outer surface adjacent to the water phase. The material exposed at 8 and 29 MPa had a double layer oxide structure, with the outer oxide layer having a much larger grain size, while the samples exposed at 0.1 MPa showed only a single spinel-phase oxide layer. Cr-depleted recrystallized austenite grains were found underneath the spinel phase oxide. The adjacent large-grained austenite substrate had M23C6 carbides in the grain interior. The implications of these results are discussed.

Jan 1, 2015

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By Donald R. Sadoway

"Molten salt electrolysis is a proven technology for the extraction of metals -- all· the world's primary aluminum is produced in this manner. The unique properties of molten salts also make them excellent media in which to treat a variety of forms of waste. Of special note in this regard is electrolysis in molten oxides, a concept put forward by the author, initially as a ""clean technology"" for producing primary metal. However, in the context of waste treatment, electrolysis in molten oxides is a process offering the prospect of changing the-valence of dissolved heavy metals while making pure oxygen gas as the main by-product. Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3, SiO2; CaO, and MgO have confirmed electrochemical production of oxygen on a carbon-free anode. IntroductionMolten salt electrolysis is the electrolytic decomposition of a compound dissolved in an ionic melt. The prime example of this process can be found in the production of aluminum. The compound, alumina (Al2O3)' derived from the mineral bauxite, is dissolved in an ionic melt comprising a multicomponent solution of cryolite (Na3AlF6)' aluminum fluoride (AlF3)' and calcium fluoride (CaF2,). The products of electrolysis are molten aluminum and carbon dioxide, the latter due to the attendant consumption of the carbon anode. Primary aluminum is produced in a reactor known as the Hall cell.' Alternatively, the compound undergoing electrolytic decomposition can be derived from waste. Processing in molten salts, with their capacity to dissolve materials to very high concentrations compared to those attainable in aqueous solutions, can be rather advantageous. High solubilities lead to high limiting current densities, and this, in tum, results in high productivities: For a primer on molten salt electrolysis and a review of the basic literature in the field of molten salts the reader is directed to an earlier publication of the author (1)."

Jan 1, 1996

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By James C. Foley

In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ monitoring of acoustic amplitude and velocity as sintering proceeds. Samples were made from elemental powders of Al (99.99%), Al (99.7%), Ag, (99.99%), Cu (99.99%) and Fe (99.9%). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and amplitude during sintering. The changes in acoustic properties were correlated with mechanical properties. Evolution of a series of reverberating echoes during sintering is shown to provide information on the state of sintering, changes in sintering kinetics as well as having the potential for detection of interior flaws.

Jan 1, 2001