Search Documents

By Marshall Khan

The Goodfellow Expert Furnace System Optimization Process (Goodfellow EFSOP?) is a proprietary process that uses real-time and continuous off-gas analysis, along with process monitoring to optimize the operation of electric arc furnaces (EAF) for steelmaking. With the exception of off-gas composition, dynamic process measurements within the EAF are not possible due to the harsh operating environment. The Goodfellow EFSOP? system provides a dynamic indication of the operating conditions within the EAF. Continuous measurement of furnace off-gas composition, along with other furnace operating parameters is used to elucidate the fate of chemical energy usage within the EAF including: the evolution of carbon from the molten steel bath; the in-leakage of air into the furnace; the extent of combustion above the molten steel bath and the occurrence of dangerous water-leaks from the furnace cooling system. The ability to measure the process reliably and continuously enables Techint Goodfellow Technologies Inc (TGTI) to implement dynamic process control of combustion within the electric arc furnace and to optimize the overall operation through adjustments to the EAF process based on off-gas measurement. This paper discusses the methodology and results achieved from several recent Goodfellow EFSOP? installations in South East Asia.

Jan 1, 2006

By Mitsutaka Hino

The contents of gangue minerals, such as A1203, P205, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year, Though the increments of such gangue contents are approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly A1203, on the blast furnace operation, the dripping behavior of FetO-CaO-SiO2-AI2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, FetO and Mgo contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper, It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When FetO content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Al2O3. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant FetO and A1203 contents. This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By Mitsutaka Hino

The contents of gangue minerals, such as Al2O3. P2O5, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year. Though the increments of such gangue contents arc approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly Al2O3. on the blast furnace operation, the dripping behavior of Fe,O-CaO-SiO2-Al2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, Fe2O and MgO contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper. It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When Fe2O content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Ah03. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant Fe2O and Al2O3 contents, This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By Kuo En Chang

Many rare earth - transition metal (RE-TM) compounds absorb/desorb hydrogen reversibly at room temperature and atmospheric pressure. For LaNi5 which is used as a battery material, the electrochemical nature of this process is well known. In the case of Nd-Fe-B which has found wide application as a powerful permanent magnet, the absorption of hydrogen has both significant advantages and disadvantages. However, a fundamental understanding of the hydrogenation process at ambient temperatures and its effect on subsequent corrosion behavior is currently lacking. This paper reports the results of the hydrogenation of NdFeB two alloys, (NdDy)15Fe78.3A10.7B6 and (NdDy)15Fe67Co5V4A12B7, which are compared with that of LaNi5. Results show that hydrogenation can be accomplished by either electrochemical methods or immersion in dilute sulfuric acid. For the latter method, the change in lattice parameter indicates that the level of hydrogen absorbed by the NdFeB particles corresponds fairly closely to an overall composition of Nd2Fe14BH2.7. Cyclic electrochemical charge/discharge experiments show that the maximum hydrogen discharge capacities of the NdFeB, NdFeB-Co-V, and LaNi5 are 40, 60, and 210 mA?h?g-1, respectively. Anodic potentiodynamic polarization measurements and calculated values of icon reveal that absorbed hydrogen in NdFeB-Co-V and the NdFeB may lead to significant increases in corrosion rates.

Jan 1, 1995

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By W. G. Davenport

Chapter 13 evaluated the %02 in blast, industrial oxygen and oil requirements for smelting FeSrCuFeS2 concentrates~ This chapter examines high eu grade CU2S-CuFeS2 concentrates the same way.

Jan 1, 2001

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By C. Mattich, A. L. Beyzavi

The Waelz Plant at Taiwan Steel Union Co. Ltd. (TSU) was erected within nine months from September 1, 1998 to May 15, 1999. The nominal capacity of the plant is 50,000 tonnes per year of electric are furnace dust (EAFD). The plant, consisting of material handling, a waelz kiln, a waste gas cleaning system, waelz oxide leaching and waste water treatment, was commissioned within three months from July 1, 1999 until October 12, 1999. The specific problem of the plant is the high chlorine content in the EAFD pellets which is up to 6 %. Lurgi Metallurgie GmbH, Frankfurt, Germany was responsible for the engineering erection and commissioning of the plant.

Jan 1, 2000

By Varuzan Kevorkijan

A new method for faster production of functionally graded metal-ceramic laminates is based on reactive pressureless counterflow infiltration/penetration of a ceramic substrate with two different metallic infiltrants. The porous or dense ceramic preform is pressurelessly infiltrated or penetrated from one side by the first metallic infiltrant to the desired cross section of the preform, producing the top layer made up of the solidified infiltrant and the underlayer consisting of reactive infiltrated preform. The partly infiltrated preform is then completely infiltrated starting from the other side by the second metallic infiltrant, in this way fabricating the internal layer, consisting of the ceramic preform infiltrated with the second infiltrant and the bottom layer formed by the solidified second infiltrant. Systems already investigated include carbide, nitride and boride ceramic performs infiltrated with aluminum and magnesium alloys.

Jan 1, 2003

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Half of the input energy to aluminum reduction cell will be lost as waste heat which could be studied for possible recovery. Since price of energy is increasing and the main production cost in primary aluminum industry is energy, so waste heat recovery consideration will be interesting. One of the possible choices for recovering is from aluminum exhaust gases that needs minimum modifications for reduction cell and has no influence on cell heat balance which is vital for the operation. By using heat exchangers with in-line and staggered tube arrangements which placed before fume treatment plant (FTP) we will be able to recover enough amount of heat. The main challenging problem which is necessary to overcome will be the heat exchanger material and its design because of corrosive and dusty exhaust gases from potroom. In this paper, a desalination system with six effects of evaporator is proposed for producing distilled water by using recovered heat from hot exhaust gases. The calculated amount of produced distilled water is around 27,000 / in this specific suggested desalination plant. The suggested desalination plant is based on Hormozgan Aluminum Company data (Hormozal) in Bandar Abbas, Iran which is constructed by the Persian Gulf.IntroductionWaste heat losses arise both from equipment inefficiencies and from thermodynamic limitations on processes. The exact quantity of industrial waste heat is poorly quantified, but various studies have estimated that as much as 20 to 50% of industrial energy consumption is ultimately discharged as waste heat [1]. In order to achieve a final decision for establishing the waste heat recovery plant in any type of industry, a strong feasibility study is mandatory. Also, we need to remember that the possible amounts of energy and suggested process plant for recovery have to be investigated before starting any feasibility study. This kind of study which is important to be finished before moving to feasibility step is mainly a theoretical study, and was done for the Hormozgan Aluminum Company (Hormozal). In addition to the exhaust gases from the potroom, the exhaust gases from anode baking plant appear to have a better potential for waste heat recovery compared to potroom exhaust gases. The average temperature of exhaust gases from anode baking kiln is 120°C higher than the exhaust gases temperature in the potroom. This needs further investigation in a different study, because this study is just focusing on potroom exhaust gases."

Jan 1, 2011

By S. P. Jupp

A 2-D coupled thermo-mechanical model was developed to simulate hot tandem rolling of AA5056 aluminum alloy using the commercial finite element software package, ABAQUS The model was used to predict the temperature, strain rate and strain distribution in the strip at any position in the roll bite and was verified through comparisons with literature results in terms of both temperature and strain predictions at the roll bite exit. A sensitivity analysis indicated that model predictions of temperature and strain at the roll bite exit were sensitive to the friction coefficient and moderately sensitive to the heat transfer coefficient for the conditions studied. Microstructure equations taken from the literature were used to make predictions at various positions in the strip. The temperature, strain rate and strain vary dramatically through the thickness of the strip in the roll bite. The sensitivity of the microstructure predictions to these parameters was assessed and it was found that using average values of temperature and strain rate in the roll bite versus exit values significantly influenced the resulting microstructure predictions.

Jan 1, 2001

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By I. H. Gundiler

Sandia National Laboratories (SNL) is tasked to support The Department of Energy in the dismantlement and disposal of SNL designed weapon components. These components are sealed in a potting compound, and contain heavy metals, explosive, radioactive, and toxic materials. SNL developed a process to identify and remove the hazardous sub-components utilizing real-time radiography and abrasive water-jet cutting. The components were then crushed, granulated, screened, and separated into an aluminum and a precious-and-base-metals fraction using air-tables. Plastics were further cleaned for disposal as non-hazardous waste. New Mexico Bureau of Mines & Mineral Resources assisted SNL in investigation of size- reduction and separation technologies.

Jan 1, 1995

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By Shawn A. Cefalu, Matthew J. M. Krane, Kent J. VanEvery

"Segregation during electroslag remelting (ESR) of a nickel-chromium-molybdenum alloy (Ni-8 wt% Cr-25 wt% Mo) has been modeled. Features of the model include species transport and AC electromagnetic effects coupled with fluid flow, heat transfer, and solidification. The effect of varying ingot diameter and melt rate, on macrosegregation patterns, local solidification time, and liquid pool profiles obtained from this model are demonstrated. The results show that the macrosegregation in the ingots correlates to the filling velocity.IntroductionElectroslag remelting (ESR) is a secondary melting process used to refine the chemical composition and the microstructure of metals. Macrosegregation of solute elements causes defects in ESR ingots, including freckles and the maldistribution of phases. These defects are not correctable through heat treatment due to the large length scales over which they occur. However, the frequency and distribution of these defects may be minimized, or even prevented, through process control based on an understanding of the conditions that lead to their formation.In the past, studies have been conducted on the effect of the process parameters on the shape of the melt pool and the thickness of the mushy zone [1-7]. In these studies, the shape of the liquid pool is determined by consideration of the heat and fluid flow induced by electromagnetic (Lorentz) force and thermal buoyancy. The transport of solute and the resultant solutal buoyancy effects were not considered in these macroscopic models. Defect formation is tied to formation of secondary phases (e.g., freckling and white spots in nickel superalloys) [5,8]. In cases where secondary phase formation is calculated (e.g., [6]), phase fractions are determined using a micro-scale model given the local solidification time (LST) and local thermal history from the macroscale model.Using the local thermal history from the macroscopic transport model to predict microstructure increases the importance of the accuracy of those results. This investigation models the macrosegregation of molybdenum during the ESR of a Ni-Cr-Mo alloy. The effect of macrosegregation on pool shape and depth is demonstrated, along with its effect on the local solidification time. By comparing the relative effects of the melt rate and ingot radius, a better understanding of the factors that affect macrosegregation, and ultimately secondary phase formation may be obtained."

Jan 1, 2004

By R. E. Moore

The lining systems currently in use in BOF furnaces, certain steel ladles, and the slag line of electric are furnaces were developed during the late seventies through the mid-eighties using a trial and error method of combining aggregate, carbon sources, additives and binders. They are currently based on magnesia, graphite, metal additives and resin binders, the selections of each being tied to the anticipated intensity of the use conditions. The general functions of the respective constituents are well appreciated, however, there is still a great deal that is not known about how the socalled antioxidants protect the graphite nor how impurities from the graphite and the aggregate enter into the wear processes. In a simplified assessment of wear processes, it appears that if the deoxidized layer can be kept very thin, less than 810 mm in depth, and if the viscosity and quantity of the matrix glassy phases can be controlled to resist erosion of the deoxidized layer, lining life can be maximized for the various applications. This paper will discuss the characteristics of the starting materials systems currently being employed for applications requiring a deoxidation function to realize extended wear. It will not attempt to explain all the complex interrelationships between the respective constituents but will point to the potential for improvements through the use of improved constituents.

Jan 1, 1991