Search Documents

By E. Morrice

Solubility of yttrium oxide (Y203) in fluoride melts was experimentally measured in the temperature range of 998 to 1273 K and, YF3 composition in LiF.YF3 melts varying from 20 to 50 mole pct using a graphite crucible in an argon atmosphere. Solubility of oxide in the melt was found to increase with increasing temperature and YF3 composition in the melt. An expression for in XY2O3 as a function of temperature for several melts was deduced. The calculated activity coefficients of Y2O3 in the melts exhibited a negative deviation from Raoult's law.

Jan 1, 1989

By Wolfgang Baum

Remediation work on thermal process dusts and slags has been primarily based on chemical analyses. These data offer little information for the assessment of treatability and reuse potential. In addition, the lack of mineralogical residue characterization has frequently caused time-consuming and inefficient waste management. This paper will outline the cost-effective, and sucessful use of process-oriented mineralogical analyses for treatment and beneficial reuse of various thermal residues. These include a patented process for detoxification of Pb-contaminated bottom ash, the pyrometallurgical treatment of K 061, the reprocessing of lead smelter slag as well as various power plant residues.

Jan 1, 1992

By W. K. Connor, O&apos

Thermal Treatment Technology Division Albany Research Center, U.S. Dept. of Energy Oregon. This evaluation included a characterization study and direct smelting tests conducted in a bench-scale electric arc furnace (EAF). In contrast to other thermal treatment technologies considered for these wastes (i.e., fluidized bed combustion), direct smelting in the EAF can process 100% of the wastes without prior beneficiation, and utilizes solid oxidant additions (in this case iron ore) rather than air to oxidize the carbon. This solid oxidant addition is advantageous because it results in the production of several value-added furnace products. These products include cast iron resulting from the reduction of the iron oxides, baghouse dust containing virtually all of the zinc from the residues, and a clean (nonhazardous) slag product suitable for recycle as concrete aggregate or construction fill. Offgas from the smelting furnace also holds potential as fuel gas for cogeneration. The direct smelting tests conducted thus far were successful at producing the desired furnace products, exhibiting the potential for complete recycle of the waste pile. A cast iron product of comparable quality to conventional cast irons was produced, at nearly 80% iron recovery to the metal. The slag product was determined to be nonhazardous, based on the EPA TCLP. Lead and zinc partitioning to the dust product was greater than 99%. The material balance over the furnace indicates that for every ton of feed processed, 540 lb. of cast iron, 600 lb. of slag, and 150 lb. of dust would be produced. Energy consumption was roughly 1.10 kWxh/lb of feed material. Prior experience suggests that these figures measured in the bench-scale furnace would translate to 0040 to 0.50 kWxh/lb at the industrial-scale.

Jan 1, 2000

By Muammer Kaya, Sait Kursunoglu

"The aim of this study was to investigate the effectiveness of ascorbic (C6H8O6) / oxalic (C2H2O4) acid as a reductant for the simultaneous recovery of zinc and manganese from a spent and mixed zinc-carbon and alkaline battery powder in sulphuric acid leaching. The effects of sulfuric acid concentration, ascorbic/oxalic acid dosages, reaction temperature and leaching time on the zinc and manganese dissolutions were investigated according to 2k full factorial experimental design; then, a simple optimization study was carried out for the best reductant. The optimum reductive acid leaching conditions were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M sulfuric acid concentration, 13 g/L ascorbic acid dosage, 1/20 g/mL solid/liquid ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. When our results were compared with the previous results, our findings were better than previous studies.In addition, the manganese dissolution kinetics was undertaken, and the activation energy was found to be 7.04 kJ/mol. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leaching solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover zinc and manganese."

Jan 1, 2012

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

By P. Henry

A novel electrochemical cell has been developed for the recovery of MnO2 from residue of pyrolusite ore leading loaded with Fe, Al Ni, Co and Si impurities, This new process can be considered as an alternative to the traditional methods : S02, H2O2 or bioleaching. It has been observed to proceed fairly rapidly and could prove to be a more economically viable process, as well as being more environmentally acceptable. Electrochemical characterization and kinetic studies have shown that MnO2 is effectively leached by electrogenerated ferrous ions at high current density from a pulp containing less than 5 g8 Fe. The chemical reactions are : Cathode (inox) : 2F23+ + 2e ? 2 Fe2+ Bulk: MnO2 + 2 fe2+ 4H+ ? Mn2+ + 2 Fe3+ + 2 H2O Anode (Pb-Ag) : H2O ? ½ O2 + 2H+ + 2e Global: MnO2 +2H+ Fe2+ = Mn2+ + H2O + 1/2 O2 The catholyte (MnO2 pulp) circulates upward in the expanded mesh cathode separated from the sulfuric acid solution anolyte by a separator which shows high mechanical resistance, low porosity, low potential drop, and reasonable cost. Laboratory and mini-pilot tests have led to the construction of an OT crating pilot plant (100 kg/hr) able to leach more than 95% of Mn, Ni, Co at 1000-1200 A/m2, 50°C with high faradic yield (> 95 %) and low power consumption (3.2 kWh/kg kWh/kg &4D). New applications like the treatment of spent Zn-Mn batteries, polluted soils, spent catalysts and oxide ore (cobalt, nickel) with electrogenerated redox species are now investigated at a laboratory and mini-pilot scale.

Jan 1, 2000

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment .step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1M sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250 °C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 1995

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By Luis W. Pommier

The wastes of the plating industry are generated in the process of rinsing the plated objects and during the cleaning of the plating shops. High volumes of hazardous waters are neutralized on site producing recyclable water, generating a metal rich, hazardous, filter cake. Occasionally, a complete plating bath has to be discarded which increases the metal content of the filter cakes. These filter cakes are discarded as hazardous at a cost of over $ 250 per ton. The metals found in the cakes are generally copper, nickel and chromium or zinc, lead and cadmium, assaying from 2% to 15% or even higher content of each metal The metals and their contents are highly variable. Some plating shops discard their products directly to hazardous waste sites, others, have them collected by companies which consolidate wastes from several producers prior to discarding. These wastes, richer in metal content than mine ores, need neither mining nor crushing and grinding for concentration. The commonly found impurities in the mine ores, i.e.: pyrites, arsenic, and valuable metals which are present in minute quantities, are absent in the filter cakes. The processes available to selectively recover the metals from the filter cakes, are discussed based on their technical and economic merits. The flow-sheets include leaching, solvent extraction when required, and electrolytic refining. Examples, showing the separation of copper, nickel and chromium and also of zinc and lead in pilot plants, show the technical and economic viability of the processes.

Jan 1, 1996

By K. Murayama, M. Kawakami, T. Takenaka, S. Yokoyama

"Cokes play an important role of spacer in blast furnace. However, they degenerate during Boudouard reaction. Blast furnace cokes are reacted with pure C02 at I 072 to 1673 K. Reaction rate was obtained by the weight change of spherical specimen. The specimen after reaction was examined by microscopic observation. The reaction rate increased with temperature and was expressed by two Arrhenius type lines. The activation energy was 126 KJ/mol at higher temperature than 13 73 K and 202 KJ/mol at lower temperature range. At the higher temperature range, the reaction proceeded from the surface leaving unreacted core, whereas homogeneously whole inside at lower temperature. The porosity increased from the center to surface at higher temperature, whereas it was almost constant at lower temperature.IntroductionThe cokes have the function of fuel, reductant and spacer to keep gas and liquid flow in the blast furnace. Thus, the reaction mechanism of coke with several gas and the strength after the reaction should be important factor to control the blast furnace operation. The reaction mechanism of coke with C02 has been studied extensively. The rate equations were derived by Gadsby[ I], Ergun[2] and Turkdogan and Vinters[3]. They were compared and discussed by Kobayashi and Omori [ 4]. Effect of crystallization degree on the reaction rate was examined by Kashiwaya and Ishii[5]. Catalytic enhancement effect of ash componets have been clarified by Kashiwaya et. al. [6]. Although degradation of coke in blast furnace has been examined recently[7], however, the degradation of coke after the reaction with C02 has not been well clarified yet. In the present work, the metallurgical coke specimen was heated in N2 and C02 and the reaction mechanism and degradation behavior after the reaction was investigated."

Jan 1, 2000

By Hiroaki Kawamura, Takeshi Yoshikawa, Kazuki Morita, Yutaka Yanaba

"To develop an alternative metallurgical process for phosphorus removal in the production of solar-grade silicon (SOG-Si), slag treatment of metallurgical-grade silicon (MG-Si) was conducted, followed by acid leaching. Phosphorus-doped silicon alloy or MG-Si containing certain amounts of phosphorus and calcium was reacted at 1723 K and 1773 K with CaO--CaF2 of several compositions. Phosphorus removal from the molten silicon into the slag phase was confirmed by reduction to phosphide ions, P3-, and phosphate ions, P3-. These ions were separately determined using a wet chemical analysis method developed by ourselves. The highest phosphorus distribution ratio obtained was 2. 7 after reaction for 18 h with 17.5 mass% CaO--CaF2 slag. We then conducted acid leaching of the silicon and achieved removal of a large fraction (over 90 % ) of the phosphorus, which was much higher than that obtained by ordinary oxidizing slag treatment.IntroductionIn recent years, the production of solar cells has been increasing rapidly. Because of this, the demand for solar-grade silicon (SOG-Si) has also been growing rapidly. The development of lower-cost mass production processes is therefore needed to provide silicon feedstock. Phosphorus is one of the impurities in metallurgical-grade silicon (MG-Si). Because of its large segregation coefficient (kp = 0.35) [l ], it is difficult to remove phosphorus using a solidification refining process. Vacuum melting is considered to be a promising method for removing phosphorous from MG-Si [2], but the issues of high cost and large energy consumption have still to be resolved.Slag treatment is often used to remove impurity elements by oxidizing reactions during general oxidation refining processes. For example, phosphorus in molten steel is removed into a slag phase as phosphate ions, PO4 3-l-, by the following reaction:"

Jan 1, 2013

By Nathaniel R. Quick

"Nd: YAG, KrF excimer, and Cu-vapor lasers are used in air to synthesize conductors and semiconductors as a second phase in silicon carbide and aluminum nitride. Conductor resistivities as low as 104 O-cm are formed in these substrates; the resistivities for the untreated substrates range from 10 11to 1014 O-cm. The silicon carbide conversion is relatively independent of wavelength while the aluminum nitride conversion shows a dependence on wavelength over the range 248 nm to 1064 nm. Silicon carbide conductors, evaluated over the range 15 K to greater than 300 K, exhibit metal like conductivity; resistivity increases with temperature. Silicon, carbon, and oxygen are identified as the principal chemical species associated with the conductor in SiC substrates while aluminum, nitrogen, and oxygen are identified as the principal chemical species associated with the conductor in aluminum nitride substrates. The silicon carbide system, which has the less complex phase diagram, is evaluated in more depth to explain the synthesis mechanism. Oxygen was principally on the surface and increasing SiC conductivity is associated with decreasing spacing between 5 µm, or less, diameter carbon globules. This technology is proposed as a replacement for metallization in electronic packages, sensors and devices. INTRODUCTIONCeramics are commonly used for multichip module, hybrid and multilayer electronic packaging; semiconductor device and sensor applications because of the insulating, conducting, semiconducting, or superconducting properties that these materials possess (1,2) The majority of ceramics, however, have not been known to exhibit conductive or semi conductive properties when exposed to rapid thermal heat processing. A ceramic and process which through selective conversion can combine two or more of these electrical properties to eliminate the need for metallization is of interest to both the commercial and military sectors."

Jan 1, 1994

By J. R. Donald

Electric arc furnace (EAF) dust, which can be considered as a by-product of the steel recycling process, contains significant quantities of recoverable zinc and iron, as well as hazardous elements such as cadmium, lead and chromium, which can be leached by ground water. The zinc in the EAF dust is found almost entirely in the form of either zinc oxide or zinc ferrite, the latter accounting for 20 to 50 percent of the total zinc. It is important that an efficient process be developed which renders the dust inert, while reclaiming the valuable metals to off-set processing costs. During the conventional carbothermic reduction processes, iron is formed, and this iron can participate in the reduction of the zinc oxide in zinc ferrite. In the present work, the reduction of the zinc oxide in zinc ferrite by iron according to the following reaction: ZnO-Fe2O3(s,s) + 2 Fe(s) = Zn(g) + 4 FeO(s) was studied in an argon atmosphere using a thennogravimetric technique. First, a thermodynamic analysis was performed using the F*A*C*T computational system. Then, the effects of briquette aspect ratio (lid), temperature, zinc ferrite particle size, amount of iron added, as well as additions such as lime, sodium chloride, and calcium fluoride were investigated. It was found that, initially, the reaction was chemically controlled with an activation energy of 178.1 kJ/mol. Then, after a product layer had formed on the outer surface of the briquette, the reaction was restricted by the diffusion of zinc gas away from the reaction interface. The parabolic rate law was fitted to the experimental data, and the parabolic rate constant was found to be: = -6.2275 + 0.0054 T (K)

Jan 1, 1995

By Toshihide Takenaka, Takashi Matsui, Nao Murakami, Masahiro Kawakami

"Electrowinning of Ti have been investigated in a LiF-NaF-KF melt including K2TiF6 at 773-923K by applying electrochemical oxidation ofH2 gas as an anodic reaction. The cathodic behavior of titanium and the anodic behavior of H2 gas were studied by voltammetry in detail to clarify the electrolytic condition for the process. The electrowinning of Ti was carried out by potentiostatic _electrolysis. Steady electrolysis was achieved under the suitable electrolytic condition without breaking out the anode effect. Titanium metal was electrodeposited on a Ti cathode though the deposits were usually powdery. It is concluded that this process is potential if the morphology of the deposit can be improved.IntroductionTitanium has such good properties as high specific strength and high corrosion resistance. However, the availability of Ti has been limited because the price of Ti is much higher than those of other common metals, such as Fe and Al. The production process of Ti ingot from its ore is rather intricate so that the production cost is high. If the simpler process is developed, the production cost should be retrenched. Titanium metal is usually produced by the Kroll process, which consists of the electrowinning of Mg metal in molten salt and the chemical reduction of TiCl.i by Mg metal. The Kroll process is very elabrate, but not simple. Because the chemical reduction ofTiCl4 by Mg metal is highly exothermic, a considerable amount of energy is wasted.Titanium metal can be electrowon in molten salt bath in principle. A simpler and more effective process than the Kroll process may be realized by the direct electrowinning so that the electrowinning of Ti metal has been studied widely[ 1]. Some researchs progressed to a pilot plant stages [2], but the electrowinning of Ti has not been industrialized yet."

Jan 1, 2000

By J. V. Happ

The investigation reported in this paper was prompted by the belief that vacuum processing of copper mattes could provide significant advancement to present-day copper smelting and converting technology. Specifically, vacuum distillation of copper mattes in a unit such as the R.H. vessel used in vacuum degassing of steel, can lead to improvements in: converter flue-gas-cleaning system, purity of acid (or liquid SO2), aisle hygiene, purity of electrorefined copper and smelter flexibility. In the study conducted, removal of Volatile impurities (arsenic, antimony, bismuth, lead and zinc) from liquid mattes, by vacuum distillation in a laboratory-scale equipment was performed. The conditions investigated covered a temperature range of 1123-1223K, absolute pressure of 6.5-0.5kPa (50 - 3 mm Hg) and with bleed gas consisting either of pure oxygen or argon. Six matte samples (four U.S. and two foreign) were tested. Under the "best" conditions arsenic and antimony were reduced to << 0.01% in the product matte. The removal of bismuth, lead and zinc was variable and appeared to be influenced by the matte composition of the sample. As might be expected, the rates of distillation of the various species were increased at higher temperatures and lower absolute pressures. The influence of a small flow rate of gas (02 or Ar) over the melt did not have a signifi¬cant influence on the extent of impurity removal. The magnetite content of the matte was reduced by up to 30% during vacuum treatment and was favored by a low partial pressure of oxygen over the melt. Substantial amounts of sulfur were also evaporated and an, overall increase in copper grade of the matte was realized. The paper concludes with an evaluation of industrial aspects of the process as applied to conventional smelters.

Jan 1, 1983

By M. Vijayalakshmi, S. Saroja, C. Sudha, T. N. Prasanthi

"Ti-5Ta-2Nb alloy and 304L austenitic stainless steel were joined by explosive cladding process. Investigations on 'as received' explosive clad revealed high hardness very near the interface due to martensitic transformation of 304L steel base plate. To improve ductility, explosive clads were heat treated in the temperature range of 823 to 1073 K for 1 to 20 h. Consequent change in the microstructure and microchemistry of the clad interface was studied. No change in the interface microstructure was observed for heat treatment at 823 K. Increase in temperature lead to the formation of various reaction zones at the interface, their number and width increase with temperature and time of thermal exposure. Growth kinetics of the reaction zones was monitored and activation energy required for formation was calculated. From elemental redistribution profiles, effective inter-diffusivities of alloying elements were calculated as a function of concentration and activation energy required for inter-diffusion was evaluated.IntroductionFor engineering components exposed to highly oxidizing and corrosive environments, a titanium based alloy i.e Ti-5Ta-2Nb (Ti-Ta-Nb) is often chosen as a structural material [1,2]. For economic consideration, vessels and piping exposed to non-oxidizing conditions are fabricated from 304L austenitic stainless steel (304L SS). Hence, dissimilar joint of Ti-5Ta-2Nb alloy and austenitic stainless steel becomes unavoidable. Fusion welding processes are not suitable for joining Ti and Fe based alloys due to the propensity for the formation of intermetallic phases and subsequent reduction in the bond strength [3,4]. Hence, explosive cladding, a solid state welding technique, was used to achieve high integrity, corrosion resistant joints between the two alloys."

Jan 1, 2012

By Flavio Begazo, William A. Enrico

"Southern Peru Copper Corporation's Ilo Refinery, the largest in Peru, began operations in 1975 with a production capacity of 165,000 stpy. Southern Peru bought the Refinery from the state owned Minero Peru SA on June 1, 1994.The Refinery processes blister from Southern Peru's I/o Smelter. Blister copper is processed in an anode plant equipped with two 365 st tilting reverberatory furnaces, a 26 mold casting wheel and an anode press machine. Copper is electrorefined in a tank house equipped with 768 commercial cells, 44 stripper cells, and 40 liberator cells, utilizing two electrolyte circuits and a 21,000 Ampere rectifier.During 1989 through 1994 a program for improving productivity was carried out by increasing the number of cells and increasing current density to the total rectifier capacity. As a result, a capacity 215,000 stpy of refined copper, 2 million tr. oz silver and 6,000 tr. oz gold per year was achieved. In 1994 Southern Peru announced plans to increase capacity to 250,000 stpy of cathode with a US$ 18 million investment and a US$ 2 million investment in environmental improvement projects, as part of the purchase agreement with the Peruvian government.This paper outlines the scope of the SPCC lio Refinery modernization and environmental program. It describes the implementation of the Electrolytic Plant expansion based on instaliation of polymer concrete cells, a new rectifier, a new selenium roaster and a Precious Metal Plant upgrades."

Jan 1, 1997

By Jeong-Soo Sohn

Physical treatment and chemical treatment of spent lithium-ion battery were studied in our research team. Especially we developed two types of acidic leaching for crushed powders containing LiCoO2 of spent lithium ion battery. One of them is sulfuric acid leaching with H2O2 as a reducing agent. The leaching rates of cobalt, lithium and the other metals were above 99 % at the condition of 2 M H2SO4, 10 vol. % H2O2, 75 °C, 300 rpm agitation speed, 250 g/5L solid liquid ratio and 75 minutes reaction time. And the other leaching process is the oxalic acid leaching. In this process more than 99% of Li and less than 1% of Co were dissolved at the condition of 3M oxalic acid, 80°C reaction temperature, 300rpm agitation speed, 50g/L initial solid/liquid ratio and 90min extraction time. Each process has its advantage and disadvantage. In sulfuric acid leaching, leaching reagent is very cheap and cobalt could be recovered into cobalt hydroxide. On the other hand, oxalic acid is more expensive than sulfuric acid but lithium could be dissolved selectively. Also cobalt could be recovered into cobalt oxalate and it could be changed into cobalt oxide after heat treatment. In order to select the effective recycling process, recovery rate and purity of cobalt hydroxide and cobalt oxalate were compared and it was investigated which process was more environment-friendly and economical.

Jan 1, 2006

A novel, low-pressure adaptation of Praxair?s coherent jet technology utilizing CoJet lances was developed for application at Inco&apos;s Copper Cliff Smelter where oxygen is available in large tonnage quantities but only at relatively low supply pressures (< 193 kPa header pressure). The project objectives were to evaluate the effect of coherent jet technology on controlling oxygen lance accretion (?horn?) formation and to increase oxygen efficiency in the Inco Oxygen Top-Blowing Nitrogen Bottom Stirring (TBBS) MK Reactor used for converting nickel- contaminated chalcocite to semi-blister copper. This paper describes the development and subsequent implementation and testing of two CoJet lances in this application.

Jan 1, 2005