Search Documents

By Tianyou Huang, Yuan Lu, Haimin Long, Jinwu Kang, Gang Nie

"The distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and less or no machining allowance, especially for large but thin steel castings such as heavy turbine blades. In the paper, a method is proposed to control the distortion by adjusting heat transfer coefficient of metal parts during heat treatment process. Required heat transfer coefficients can be realized by getting the metal parts into contact with various media such as water spray, insulation felt or materials with different heat conductivity. The control method based on this idea is set up and achieved. By using insulation felt and water spray to change the heat transfer coefficient during the stages of heat treatment process, the results indicate that the proper control time and vary with materials.IntroductionThe distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and to realize less or no machining allowance [1]. For example, the Three Gorges turbine blade’s distortion is as large as 50mm during heat treatment process. The uneven heating and cooling during heat treatment process is the main reason for distortion [2]. By adjusting heat transfer coefficient of different areas of metal parts, the heat treatment process could be controlled. The temperature variation, direct cause for distortion, could be under control. Loeser Klaus used high pressure gas to achieve uniform heat transfer during gas quenching and proposed the possibility to use ""Dynamic Quenching"" processes where the quenching severity is varied during quenching by stepwise control of either gas velocity or gas pressure [3]. Li Zhichao also suggested minimizing distortion by marking a component into several areas and imposing different heat transfer coefficients on each area [4]. Heat transfer coefficient can be controlled by getting the metal parts into contact with different media such as water spray, insulation felt, air or different heat conduction materials. In addition, the exact time to adjust the heat transfer coefficient is another factor for distortion. A method is presented in this paper by actively adjusting heat transfer coefficient for different areas of metal parts and different stages of heat treatment process to control their distortion. The corresponding experiments have been made by using different metal materials."

Jan 1, 2012

By Toshiaki Akahoshi

Keywords: Wasted catalyst, Hydrodesulfurization, Ammonium vanadate, Ammonium molyb-date, Hydrometallurgical process. The fundamental reactions have been investigated in order to develop a hydrometallurgical process for recovery of molybdenum and vanadium from wasted catalysts generated in the hy-drotreating desulfurization of heavy oil. The principal steps of the process are a mild oxidation roasting of the waste catalysts at temperature around 500°C, leaching of the target metal components with dilute ammoniacal aqueous leachates, selective precipitation of vanadic acid, and ammonium molybdate precipitation. The selective recovery of vanadium as vanadic acid is successfully performed using ammonium sulfate as a salting-out agent. Recovery of ammonium molybdate is based on large dependence of solubility of ammonium molybdate in ammoniacal solutions upon temperature and ammonium salt concentration. In this process, the solution after recovery of vanadium and molybdenum is recycled to the leaching stage of the roasted materials, and the ammonium salts in the process liquor is in the repeated use. Employment of am-moniacal system makes it possible to operate the roasting at much lower temperature than that for the currently operating process.

Jan 1, 2005

By Debbie Marshall

Process water is an important consideration in the development of a nickel laterite project. Depending on the location of the ore body, sufficient fresh water may not be available and it may be necessary to use seawater (or saline groundwater) for ore preparation. This introduces various species, which have major effects on materials of construction and leaching chemistry. This paper summarizes batch testwork completed at the Falconbridge Technology Center. The leaching behaviour of eleven different laterite ore samples were compared using seawater and fresh water. For brevity, six of the eleven samples are reported here-the other five samples showed similar results. Each ore type was leached under identical conditions in both freshwater and seawater and the leaching chemistry compared. The batch test results were confirmed in a continuous pilot plant, and leach kinetics for the two systems were compared. Keywords: high pressure acid leaching, laterites

Jan 1, 2004

By R. W. Bartlett

A two step process for treating platinum group metal flotation concentrates Is described while experimental results. The process was designed to be simple and Inexpensive While yielding a high recovery and fast turnaround. Ii consists of electric furnace smelting of concentrate to remove gangue and produce a homogeneous sulfide matte containing all of the base metals and platinum group metals. Sulfide oxidation Is minimized during smelting to avoid Installing an acid plant In the second step, matte Is pressure-leached with oxygen In an acid sulfate system to dissolve Iron, nickel, ?and copper while leaving a residue highly concentrated In precious metals, and typically about 1% of the flotation concentrate mass, A batch process with oxygen titration against the base metal composition of the feed Is used to control the end point of the leach. Sulfides must be eliminated while minimizing the precipitation of hydrolysis products. The leach residue can be smelled to bullion to facilitate sampling accuracy.

Jan 1, 1989

By H. Bernier

The Noranda Inc., CCR Division, copper refinery located in Montreal-East, Québec, Canada, has expanded over the years to reach a capacity of 410,000 metric tons of cathode production per year. The expansion process resulted in nine, parallel, 200 m. long bays each equipped with its overhead cranes and manually operated washing machines. Anode scrap washing and piling was done manually. The mechanization of the tank house involved the elimination of 18 cells at one end of each of the bays in order to install transfer conveyors where anode scrap and cathode loads are deposited by the bay cranes. The cathode loads are brought by new transverse cranes to new machines where cathodes are washed, piled in predetermined bundle weights, check weighed, strapped then shipped in trucks or railroad cars. Suspension bars are automatically removed, stacked in magazines and sent back to the starting sheet machines. Anode scrap loads are brought to machines located near the anode furnaces where they are washed and piled in bundles for easy charging. The mechanization has eliminated numerous hazardous jobs and has realized a reduction of 0.2 man-hours/ton. After these modifications, the refinery production capacity now stands at 370,000 metric tons per year.

Jan 1, 1987

By V. Ramachandran

The Amarillo Copper Refinery, the newest and most modern copper refinery in the world, has been in operation for the last eleven years and has a rated capacity of 460,000 st/yr. The tankhouse - a structure that covers 500,000 ft2 under one roof - extends one-half mile in length and is a model of materials-handling efficiency. The use of recently developed and patented* reagent control technology, termed "Reatrol Process", has increased current efficiencies to an average of 98% and has considerably improved the physical and chemical quality of the cathode deposit. The present paper describes the current operations at the Amarillo Copper Plant with special emphasis on tankhouse operation.

Jan 1, 1987

By Tuomas Hirsi

The world’s first large scale modular solvent extraction plants have been delivered by Outotec. The first of these is now in operation and has proven that the VSF®X technology can deliver the excellent performance of the Outotec VSF® solvent extraction process. Modular delivery allows site work to be minimized and the manufacturing done in a controlled environment, allowing for serial production manufacturing benefits. Container based delivery was found to be a highly efficient way of utilizing the standardized transportation methods on a global scale. Site work with modular units was found to be efficient and highly predictable. In this paper, we present the first successful Outotec VSF®X deliveries and discuss the benefits of the modular delivery and design compared to the standard solvent extraction installation’s delivery. The process performance of the VSF®X is also discussed with experiences from the first industrial reference presented.

By A. A. Trickett

In the treatment of gases from pyrometallurgical processes prior to acid manufacture, volatile components, sulphur trioxide and particulates ,are removed in wet gas cleantng systems. In the process a weak acid stream is generated, typically less than 10% H2S04, contaminated with volatiles such as arsenic, fluoride and chloride', plus metallic particulates. This effluent stream has, in the past, been disposed of in a variety of different ways. As a result of changing environmental legislation, smelters are having to review alternative solutions for treating this effluent stream. This paper' will describe a process developed by Chemetics which treats this effluent stream, generating a small dry metal sulphate stream plus a clean acid stream which is suitable for recycling to the smelter acid plant.

Jan 1, 1992

By Qian Li, Li-chen Hou, Yong-bin Yang, Tao Jiang, Jian-jun Hu, Bing Xu

Extraction of gold from refractory gold concentrates usually requires an oxidation step to remove arsenides、sulphides and carbonaceous matter. In this investigation, the gold concentrates were two-stage roasted under different atmospheres and temperatures. Results indicated that at the first stage, under neutral atmosphere, the removal rate of arsenic increases as the temperature rises. Under the oxidizing atmosphere, with the increase of temperature, arsenic content in the residued calcine increases, in addition, the volatilization of arsenic is also affected by the oxidation of carbon that generated CO, which is advantageous to the decomposition of arsenate decomposition. At the second stage of roasting, it is the higher temperature and stronger oxidizing atmosphere, the faster sulfur and carbon oxidated rate is, but at the same time, the calcine appears the phenomenon of consolidation because of the phase of silicate compounds generate.

Jan 1, 2015

By Zhi-gang Que, Sheng-li Wu, Guo-liang Zhang, Bo Su, Chao-gang Hou

NOx released during fuel combustion is one of the major air pollutants, such as acid rain and photochemical smog. At present, still not have an economical and effective method of inhibiting NOx emission for sintering flue gas. Therefore, controlling conditions of fuel combustions to enhance the reduction of NOx is important for decreased the emission. In this study, microsintering furnace has been performed to investigate the effects of NOx emission from char-N during coke breeze combustion. The results show that the emission concentration of NOx decreased with increasing temperature when it is sinter bed temperature higher than 1000℃. The lower emission concentration of NOx was obtained when the concentration of oxygen was decreased. And the maximum concentration of NOx will be reduced with the enhanced of heating rate. If heating preservation time was prolonged, it would promote to NOx reduction with reduction substances resulted in lower NOx emissions in the combustion of coke breezes.

Jan 1, 2015

By Rongshan Qin, Dengfu Chen, Yan Zhao, Mingtu Ma, Yang Li, Xinming Wan

A two dimensional cellular automaton (CA) model coupled with finite element (FE) method has been developed for simulating the formation of solidified microstructure during beam blank continuous casting, which represents columnar and equiaxed dendrites growth in the case of detailed secondary cooling boundary conditions. In this model, a new adaptive mesh division is proposed to couple CA cubic lattice and irregular FE mesh of beam blank. A double-accuracy liner interpolation method is employed to obtain micro CA temperature field via macro FE calculation. The nucleation process and the velocity of dendrite tip are calculated by continuous nucleation model and KGT model, respectively. Moreover, the preferred orientation of dendrite growth is determined using a probabilistic model. The effects of super heat and casting speed on the microstructure characteristics are analyzed. This model can be applied to optimize processing parameters for beam blank continuous casting basing on microstructure evaluation.

Jan 1, 2015

By Yungang Li, Hui Li, Ramana G. Reddy, Jinglong Liang

High solid corrosion protective coatings were prepared by the dust of the converter with an average particle size of 59.33 μm. The effect of different amount of benzyl alcohol diluent on the performance of high solid anti-corrosion coatings was studied. With the increase of the amount of diluent, the viscosity of high solid anti-corrosion coatings reducing, the film apparent bubble content decreasing, and film resistant to salt water corrosion ability decreased, while acid corrosion capacity enhancement. When the dosage of diluents is 15%, the coating film is more resistant to acid corrosion.

Mar 1, 2017

By Lucio Fabio Cassiano Nascimento, Luis Henrique Leme Louro, Sérgio Neves Monteiro, Jheison Lopes dos Santos, Fernanda Santos da Luz, Fábio Oliveira Braga, Rubens Lincoln Santana Blazutti Marçal, Hugo Concolato de Oliveira Freitas, Édio Pereira Lima Júnior

Epoxy matrix composites reinforced with up to 10, 20 and 30 vol% of continuous and aligned natural mallow fibers and 30 vol% of mallow and jute hybrid fabric were for the first time ballistic tested as personal armor against class III 7.62 mm FMJ ammunition. The ballistic efficiency of these composites was assessed by measuring the dissipated energy and residual velocity after the bullet perforation. The results were compared with that in similar tests of aramid fabric (Kevlar™) commonly used in vests for personal protections. Visual inspection and scanning electron microscopy analysis of impact-fractured samples revealed failure mechanisms associated with fiber pullout, rupture and layers delamination. When compared to Kevlar™, the mallow fiber and hybrid fabric composite displayed practically the same ballistic efficiency. However, there is a reduction in both weight and cost, which makes both, mallow fiber and hybrid fabric composites, a promising material for personal ballistic protection.

Mar 1, 2018

By Felix Wolters, Michael Schütt

In over 40 years of operation, engineers at Aluminium Oxid Stade GmbH (AOS) have acquired a lot of experience whereby they have developed a series of optimizations regarding the specific primary energy consumption. The tube digester technology, invented by VAW in Germany and applied on an industrial scale for the first time in Stade, was brought to perfection by its innovative cleaning methods, which led to a constantly high heat transfer, low pressure loss and excellent availability of the digesters. Further improvements such as the heat recovery from the exhaust gas stream of the salt heater as well as the optimization of one of the fluid bed calciners and the installation of a combined heat and power generator (CHP) led AOS to where it is now—a leading alumina refinery with regard to the lowest energy consumption per ton of alumina.

Mar 1, 2017

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By B. C. F1intoff, R. G. Bradburn, E. Groiss

"The concentrator at Brenda Mines Ltd. treats a copper - molybdenum porphyry ore with current head grades of 0.185% Cu and 0.036% Mo. The consistently low head grades provided the driving force to explore methods of improving plant productivity. Computer based process control was recognized as one means of addressing this objective. Over the period from 1974 to 1982 a control system evolved which now extends to every area of the mill. Control strategies are built on elements of classical, modern and rudimentary expert control. In addition, the control system has often served as a catalyst for other technological developments. The economic returns associated with the system are very significant and it has played an important role in the mine's survival in times of poor metal markets. This paper presents an overview of the computer control system at Brenda.PreambleOne can scarcely avoid picking up a trade magazine or newspaper today without seeing some reference to technology and its potential impact on North American business. _A recurring theme is the need to apply technology to raise our standard of plant automation in the manufacturing and process industries. The general thesis of these articles has been concisely captured in the mutually exclusive set:AUTOMATE or EMIGRATE or EVAPORATEProcess control is one form of automation that has been successfully exploited by various sectors of these industries. In minerals and metal processing the wide scale adoption of process control technology has, until recently, been largely limited to a few companies - most of whom have a history in the area dating back to the early 1970’s. However, there is definitely an increased and much broader interest in process control as a technology which can improve performance, productivity and profit.The economic hardships that were visited on the mining industry in the early 1980's are not easily forgotten. It is the authors' conviction that the mining industry must move to implement proven technology, in particular process control, in order to be well postured for the next (inevitable) down cycle.In pursuing the technical and trade literature, one can discover a number of example of the successful utilization of process control systems in mining and related applications. In the text which follows, the authors describe the process control efforts undertaken in the Brenda Mines Ltd. concentrator."

Jan 1, 1989

By Jae-Ho. Lee

For some electronic applications where a dispersed electrically-conductive particulate-phase is employed, the conductivity of the surface (or near-surface region) of the particles provides for the primary mechanism which determines its electrical conductivity. Particles of a less expensive material, which may have desirable thermal-expansion properties, when coated with silver offer a means of also obtaining desirable electrical properties and at low cost. The research conducted was focused primarily on the development of silver-coated tungsten particles for thick-film polymeric conductors. The ammoniacal electrolyte was formulated from silver-nitrate, glycine inhibitor and formaldehyde reductant. The reduction, and subsequent deposition, of silver occurred selectively on the surface of the tungsten particles. Coated particles were assessed by SEM imaging. The thickness of the silver coating was estimated to be approximately 100nm on the basis of a mass account and the coating being uniform. The electrical conductivity of a silver-coated tungsten-powder pellet was found to be similar to that of a silver-powder pellet, of identical geometry.

Jan 1, 1997

By Annette Revet

Aluminum fluxes have been used for the remelting of secondary aluminum since the beginning of the recycling industry. During the last sixty years, a number of fluxes have been designed, researched and tested at the laboratory and plant scale. Fluxes are primarily a mixture of potassium chloride and sodium chloride with the addition of some other chloride and fluoride containing salts. The conventional Mining methods of potassium chloride and sodium chloride yield products that are not high in purity without costly reprocessing or additional refining. In 1993, Kalium Chemicals, Ltd. began supplying flux mixtures to the aluminum industry. Kalium produces potassium chloride and sodium chloride which are mined and refined by a patented solution-mining process. The salts produced by this process are high in purity with lower concentrations of iron oxide, sulfates, and other impurities. This paper will present the different mining methods used in the production of sodium chloride and potassium chloride. The paper Will address how these mining methods affect the purity of the final product as well as the effect of purity on the performance of the fluxing salt.

Jan 1, 1995

By M. Kobayashi, Y. Nishisu

"Fine multicomponent particles of yttrium and europium were synthesized through the precipitation from homogeneous solution, and the various characteristics related with the fluorescence were investigated. The morphology and the fluorescent characteristics of the synthesized particles were affected by ionic species in the stock solution. In the presence of sulfate ion, some parts of the precipitated particles were aggregated, and _the fluorescent characteristics were not good. On the other hand, in the presence of chloride ion or nitrate ion, the particles precipitated were almost monodispersed, and, the intensity of the fluorescent emission were strong after calcination. Further, these particles were also very attractive as the red phosphor in the mercury-free fluorescent systems.Introduction Eu doped Y oxide particles have been widely investigated for the application to the fluorescent lamps and displays: Recently, the fluorescent lamps are pointed as harmful electric equipments because of using mercury for excitation. Therefore, the use of the mercury in the fluorescent- system will be limited or prohibited worldwide in near future. Then, the development of the mercury-free fluorescent lamp is strongly required without delay. Inert gas such as neon and/or xenon seem to be applicable as new excitation element that replaces the mercury. However, in case xenon the excitation wavelength,' 146 and 172nm, is different from that of the mercury, 254nm, and then, the commercial phosphors which are used in the present fluorescent lamp system are not available. Therefore, the invention of the novel phosphors is essential for the development of the mercury-free fluorescent lamp. Further, the controls of the size and shape of the particles precipitated are also important, because the homogeneity of the size and the shape is very important for the fabrication of the layer of the phosphor particles. That is to say, the development of the phosphor particles with controlled components, size and shape is essential. The precise control of size and shape improves the packing density, and so, the screen performance of the lamp [1]. In addition, these phosphor particles should be also useful for the application of the flat-plane displays, for example, PDP, etc. [2,3]. In the present work, first, the particles including yttrium and europium for the precursor for red phosphor were prepared through precipitation from homogeneous solution. This process was precisely controlled for the control of the components, size and shape of the particles precipitated. Next, the particles precipitated were calcined, and then, their fluorescent properties were characterized. As a result, some of them showed the possibly available characteristics as the red phosphor for mercury-free fluorescent lamp system. These experimental results are presented in this paper."

Jan 1, 2000

By Zhang Yongzhu

Sulfoxides are one kind of extractants for precious metals. The structure, the coordination reaction, the extraction behaviour and the precious metals complexes of sulfoxides are summarized. The differences between sulfides, sulfoxides and sulphones are also discussed.

Jan 1, 1992