Search Documents

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.

Jan 1, 2003

By Finn E. Bronner

HISTORICAL PERSPECTIVE "Blessed be the Lord my strength, which teacheth my hands to war and my fingers to fight." Thus sang David three thousand years ago, in tacit acceptance of the condition of war, and in praise of the exceptional military skills with which this warrior king of Israel was endowed. He had cause to exult, for he had consolidated King Saul's conquests and added new ones of his own, not least of which was the capture of Jerusalem. David revealed in this operation that his mastery of the military arts embraced not only the weaponry and tactics of his day, but also strategy and that oldest of intelligence techniques: spies. The Jebusites, who built Jerusalem, had encompassed the city with the first of its many walls, but had neglected to incorporate the sole reliable water supply within its perimeter. This was Ain Gihon, today called the Fountain of the Virgin, which bubbled out on the east slope of Mount Ophel, one of the ridges on which Jerusalem was built, and drained eastward into the Kidron Valley. Water was brought into the city in the traditional manner: by women descending the stony trail outside the wall to fill their jars at the spring. But this essential daily activity was vulnerable to interruption by a hostile force outside the walls. To remedy this weakness, the Jebusites had driven a gallery from the spring a short distance into the water-bearing limestone under the city, and there cut a small collecting basin in the rock, a common way to develop springs throughout this arid region. But then the Jebusites dug a small vertical shaft from the roof of the gallery above the cistern upward about 15 m. From the upper end of this shaft, they constructed a narrow inclined tunnel with rock-cut steps leading up to the city streets. Thus the water supply could be reached even in time of siege.

Jan 1, 1979

By Jean-Michel Rendu

That you are giving the Daniel C. Jackling award to me is a great personal honor. But more significantly, it is a recognition that geostatistics has come of age. And since I am considered by many as belonging to an older generation of geostatisticians, I thought that it would be fitting that I reflect on where geostatistics came from and where it might be going. First, though, let me propose a definition of geostatistics. Etymologically, paraphrasing Webster's definitions of "geo" and "statistics," it is "a branch of mathematics dealing with the collection, analysis, interpretation and presentation of masses of numerical data taken from the earth." This definition is most appropriate in the context of mining geostatistics. It includes both classical and spatial statistics. It emphasizes the earth aspect, or the analysis of geologic features. And it should remind the practitioner that geologic input is a critical part of all geostatistical applications. In the 1910s, statistical methods were already used to analyze geological data. However, the origin of geostatistics, as we know it today, is best set in the late 1940s, when H.S. Sichel recognized the lognormal distribution of sample values in the South African gold mines. In 1951, Daniel Krige observed that "it can be expected that the gold values in a whole mine will be subject to a larger relative variation than those in a portion of the mine." In other words, samples taken close to each other are more likely to have similar values than if taken farther apart. This observation is the foundation on which spatial statistics, which characterizes values defined in a multidimensional space, is built. However, the 1950s were marked by studies based on classical, as opposed to spatial, statistics. It was only in the 1960s that the need was recognized to model the similarity between sample values as a function of the distance between samples and that the semivariogram was defined. A theoretical framework was developed by Matheron that supplied an elegant mathematical explanation to the empirical observations made by Krige. Matheron coined the term "kriging" in recognition of Krige's pioneering work on the geostatistical evaluation of mineral deposits. As soon as this theoretical framework was developed, it was possible to bring geostatistics to the academic world. The "Centre de Geostatistiques" was founded in Fontainebleau. Numerous students were trained there, disciples eager not only to improve the theory and develop more sophisticated mathematical tools, but also to spread the new faith throughout the world. Expansion of geostatistics exploded in the 1970s, arguably the most fertile decade if it is judged by the frequency of theoretical breakthroughs, the number of original publica-

Jan 1, 1995

By M. Imazu, Ö. Aydan

"A new rock classification, Rock Mass Quality Rating (RMQR) proposed by the authors is briefly explained and its application for the design of tunnels and large underground openings support systems is described in this paper. RMQR is an index to evaluate the state of rock mass. The preliminary support design may be based on the concept to prevent structurally controlled failures of rock mass. RMQR can also evaluate the yielding characteristics of rock masses so that it is possible to design a support system to prevent or control the deformation of surrounding rock through the utilization of the proposed rock mass classification and some analytical and numerical techniques.INTRODUCTIONThe first three authors proposed a new rock classification system named Rock Mass Quality Rating (RMQR) (Aydan et al. 2014). RMQR quantifies the rock mass state, and using the classification system together with intrinsic geo-mechanical properties of intact rock, possible geo-mechanical properties of rock masses can be estimated. The instability modes of underground openings can be structurally controlled because of the orientation of discontinuities in rock mass and the in-situ stress induced (Aydan 1989; Aydan et al. 1993, 1996; Aydan and Genis, 2010). The authors (Aydan and Ulusay, 2013; Aydan, 2016) have also tried to apply this system to the design of a tunnel support system. The authors presented initial guidelines for the RMQR classification system earlier (Aydan and Ulusay, 2013).In this paper, the authors provide further guidelines and establish some criteria for support system design that considers loading conditions and types of underground structure according to RMQR. Guidelines are alsos proposed for selecting the proper size of rockbolts, rock anchors, shotcrete, steel ribs and concrete liner. These guidelines are based on past experiences with various underground structures, theoretical understanding and the anticipated behavior of rock mass under given in-situ stress conditions and excavation techniques. The authors also utilized some databases developed for large underground caverns and tunnels excavated in squeezing or rock-bursting ground conditions."

Jan 1, 2016

By Yoginder P. Chugh

It is well known that weak floor conditions in central Illinois affect pillar and mine opening stability. The floor interaction with coal pillars and immediate mine roof are being studied using two dimensional (plane-strain) elastic-plastic finite element models. The effects of varying soft floor thickness, coal seam- thickness, width of mine openings and strength parameters of coal and mine floor are being evaluated. The finite element models developed by Agbabian Associates and Dahl were utilized in this study.

Jan 1, 1982

By R. Dewey

WHAT IS AI? It's very hard to say. Most researchers and practitioners disagree with nearly any attempted definition, but most would agree that A1 does deal with the development of computer-related methods o f problem-solving. Artificial intelligence is a discipline which seeks to emulate human anatomy and/or thought processes by applying computer science, electronics, and mechanical engineering to the development of natural language processing, machine vision, robotics, and knowledge-based expert systems. Integration of these four fields will someday produce the robots of today's science fiction. A1 addresses problems of structuring large amounts of knowledge and representing relationships with rules and semantic frameworks rather than with mathematical equations. A1 is convergent rather than divergent - - conventional conputer applications use relatively small quantities of input to generate large output, but A1 generally reduces large amounts of information to establish a few major conclusions. The development of A1 has prompted greatly increased efforts on the part of scientists and engineers to understand just how humans think, organize information, approach problem-solving, and form conclusions. Some of the more exciting and possibly far-reaching advances in A1 are coming in this more-or-less soft-science area. Thirty years of A1 research (dating from a 1956 conference at Dartmouth College at which the term A1 was coined) has already spawned many widespread, almost ordinary, products: window graphics, hand-held controllers (mouse). function menus, etc., all in an attempt to make computers and people more compatible. WHAT IS AN ES? A1 can be used to develop EXPERT SYSTEMS, which are computer programs or systems which contain knowledge and rules by which problems can be solved. or at least by which possible solutions can be suggested for very complex problems. A1 can be used to better define problems so that solutions can be found. An ES is designed not to process numbers, but to process information according to rules and logic derived from actual practice and experience. WHY AI? WHY ES? Companies are increasingly aware of the value of accumulated knowledge and experience in designing, building, operating, and maintaining the increasingly complex or expensive physical plants in any business. As knowledge branches out and becomes more specialized, the accumulated learning of a veteran operator or manager or engineer becomes a scarce resource well worth preserving. EXPERT SYSTEMS offer a means of doing that, reinforcing, not replacing, human capabilities.

Jan 1, 1987

By Fathi Habashi

METALS COMMONLY leached may come from one of the following sources: 1) Occurring in nature in the native state, e.g., gold, silver, platinum metals, copper. 2) Produced as by-product of a metallurgical process, e.g., gold, silver, platinum metals, selenium. 3) Produced by reduction of an oxide ore, e.g., copper, nickel. GOLD AND SILVER Cyanidation According to Mellor (1923) the alchemists of the eighteenth century knew that gold was soluble in aqueous solution of potassium cyanide, and the early jewelers probably utilized this fact in gilding. He also mentions that Scheele in 1783 and later Bagration in 1843 noted the solvent action of aqueous solutions of alkali cyanides on gold. Yet it was not until 1887 that the value of this observation was recognized, when MacArthur and Forrest (1887) made use of it in leaching gold from its ores. Since then, the process has spread to every gold and silver mining district in the world.

Jan 1, 1970

By Bruce Kennedy, William Hustrulid

Georgius Agricola in 1556 wrote De Re Metallica, one of the first and probably the most famous of mining reference works. In Book 1 he reflects rather elegantly on mining and miners. "Many persons hold the opinion that the metal industries are fortuitous and that the occupation is one of sordid toil, and altogether a kind of business requiring not so much skill as labour. But as for myself, when I reflect carefully upon its special points one by one, it appears to be far otherwise. For a miner must have the greatest skill in his work, that he may know first of all what mountain or hill, what valley or plain, can be prospected most profitably, or what he should leave alone; moreover, he must understand the veins, stringers, and seams in the rocks. Then he must be thoroughly familiar with the many and varied species of earths, juices, gems, stones, marbles, rocks, metals, and compounds. He must also have a complete knowledge of the method of making all underground works. Lastly, there are the various systems of assaying substances and of preparing them for smelting; and here again there are many altogether diverse methods. ... "Furthermore, there are many arts and sciences of which a miner should not be ignorant. First there is Philosophy, that he may discern the origin, cause, and nature of subterranean things; for then he will be able to dig out the veins easily and advantageously, and to obtain more abundant results from his mining. Secondly, there is Medicine, that he may be able to look after his diggers and other workmen, that they do not meet with those diseases to which they are more liable than work- men in other occupations, or if they do meet with them, that he himself may be able to heal them or may see that the doctors do so. Thirdly follows Astronomy, that he may know the divisions of the heavens and from them judge the direction of the veins. Fourthly, there is the science of Surveying that he may be able to estimate how deep a shaft should be sunk to reach the tunnel which is being driven to it, and to determine the limits and boundaries in these workings, especially in depth. Fifthly, his knowledge of Arithmetical Science should be such that he may calculate the cost to be incurred in the machinery and the working of the mine. Sixthly, his learning must comprise Architecture, that he himself may construct the various machines and timber work required underground, or that he may be able to explain the method of the construction to others. Next, he must have knowledge of Drawing, that he can draw plans of

Jan 1, 1982

Acid mine drainage (AMD) forms when sulfide minerals are exposed to oxidizing conditions in coal and metal mining, highway construction, and other large-scale excavations. Iron sulfides common in coal regions are predominately pyrite and marcasite (FeS2), but other metals may be complexed with sulfides forming chalcopyrite (CuFeS2), covellite (CuS), galena (PbS), and sphalerite (ZnS). Pyrite commonly occurs with these other metal sulfides thereby causing AMD where Cu, Pb, and Zn are mined. Upon exposure to water and oxygen, sulfide minerals oxidize to form acidic, sulfate-rich drainage. Metal concentrations in AMD depend on the type and quantity of sulfide minerals present. The drainage quality emanating from underground mines or backfills of surface mines is dependent on the acid-producing (sulfide) and alkaline (carbonate) minerals contained in the disturbed rock. In general, sulfide-rich and carbonate-poor materials produce acidic drainage. In contrast, alkaline-rich materials, even with significant sulfide concentrations, often produce alkaline conditions in water. Approximately 20,000 km of streams and rivers in the United States are degraded by AMD. About 90% of the AMD reaching streams originates in abandoned surface and deep mines. Since no company or individual claims responsibility for reclaiming abandoned mine lands (AML), no treatment of the AMD occurs and continual contamination of surface and groundwater resources results. The oxidation of iron disulfides and the generation of acidity occur through several reactions (Stumm and Morgan, 1970). The chemical equations can be found in Caruccio and Geidel (2000). If any of the processes represented by the equations were slowed or altogether stopped, the generation of AMD would also slow or cease. The equations show that 1000 Mg of rock containing 1% sulfur, all as pyrite, would yield upon complete reaction 31.25 Mg of acidity. Therefore, 31.25 Mg of 100% CaCO3 would be required to neutralize the acidity. The alkaline content of overburden determines whether there is enough neutralization potential (NP) to counteract the acid produced from pyrite oxidation. Of the many types of alkaline compounds present in rocks, only carbonates and clays occur in sufficient quantity to effectively neutalize AMD. A balance between the acid-producing potential and neutralizing capacity of an overburden sample will indicate the ultimate acidity or alkalinity that might be expected in the material upon complete weathering. Accurate prediction and control of AMD before surface mining require an understanding of three important factors: 1) overburden geochemistry, 2) method and precision of overburden handling and placement in the backfill during reclamation, and 3) the postmining hydrology of the site.

Jan 1, 2002

By D. R. Babich, E. R. Bauer

Noise induced hearing loss (NIHL) continues to be a problem in the mining industry. New noise standards (Part 62) promulgated by the Mine Safety and Health Administration (MSHA) are aimed at reducing NIHL in the mining industry. The National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in mining. Noise surveys, including full-shift worker noise exposure and equipment noise profiling, have been completed in several surface coal mines, with an emphasis on draglines. The results of these studies are reported, their implications concerning worker NIHL are addressed, and their application to administrative and engineering controls is discussed.

Jan 1, 2003

By I. K. Kapageridis

Environmental management and planning requires the integration of large volumes of disparate information from many sources and the analysis of this information with efficient tools for assessment and evaluation. Effective methods of communication that allow interactive participation in the planning, assessment and decision-making processes are also very important. The VULCAN software package from Maptek (Pty) Ltd comprises a large number of 3D graphical tools within an interactive 3D interface called ENVISAGE. These tools are designed and developed to help engineers and scientists to identify and solve environmental problems. The combination of VULCAN 3D Software and the I-SiTE 3D Laser Imaging system leads to powerful solutions for environmental management. This paper presents the capabilities of this integrated system and its applications for environmental management.

Jan 1, 2002

By Maurice C. Fuerstenau

INTRODUCTION The term, chelate, from the Greek for 'claw,' has its origin in the pincer-like representation of more than one atom of a single ligand bonded to the same metal atom, forming a ring-like structure. Depending on how many attachments exist on the sphere of coordination around the metal ion, ligands are referred to as bidentate, tridentate, tetradentate, pentadentate and hexadentate According to Calvin and Martell (1952) and Somasundaran and Nagaraj (1984), chelating agents must contain suitable functional groups, and their location within the ligand molecule must enable ring formation that is sterically possible. Typical structures that meet these requirements have been given by Fuerstenau and Herrera-Urbina (1988) and are listed in Figure 1. As noted, the functional groups of these reagents contain electron donor atoms such as oxygen, nitrogen and sulfur. Basic groups, such as amino (-NH,), are those that contain an atom with a lone pair of electrons. Acid groups are those, such as carboxylic (-COOH) which lose a hydrogen ion and coordinate with the metal atom. Examples of each of these types chelating reagents are given in Tables 1-4. The specificity of chelating agents for various metal ions has long been known and was utilized early in the search for new flotation collectors. In 1927, Vivian used ammonium nitrosophenylhydroxylamine as a collector for cassiterite. Holman (1929) tested dimethylglyoxime as a collector for nickel oxide. He also suggested taurin as a collector for oxidized lead ores. DeWitt and von Batchelder (1939) suggested the use of oximes as flotation collectors. Gutzeit (1946) conducted an extensive investigation on the use of chelating agents as collectors and as depressants for gangue minerals. The depressants are those reagents that form soluble chelates with metal ions that could function as

Jan 1, 2005

By T. Ruff, J. Steele

The lack of visibility near earthmoving equipment results in an average of five fatalities in U.S. surface mines each year. These accidents occur when a piece of equipment either strikes another vehicle or worker, or travels over the edge of an embankment. Researchers at the National Institute for Occupational Safety and Health have evaluated off-the-shelf proximity warning systems that sense obstacles near the equipment and provide an alarm to the operator. Limitations of existing systems have necessitated the development of new systems designed specifically for mining equipment, including a GPS-based proximity warning system and a computer-assisted stereovision system.

Jan 1, 2004

By Earl Cook

Introduction Men like physical power because it gives control over nature and over other men. Physical power comes in two common forms: explosive and non-explosive. In both forms, the most powerful devices yet invented make use of nuclear energy: on the one hand, the hydrogen or fusion bomb, and, on the other hand, a nuclear power plant. For some nations, nuclear power offers a measure of independence not otherwise available in a time of diminishing and unevenly allocated fossil fuels. Consequently, it has great attraction. Unfortunately, the application of nuclear energy (especially fission energy) to either explosive or electrical power entails a singular risk, that of injury from ionizing radiation, both natural and induced; this risk is found in all stages of the nuclear-fuel cycle, from mining of fissionable materials to the disposal of wastes produced in the "burning" of nuclear fuels. The health costs of nuclear power were not fully assessed in the early stages of the development of nuclear technology and some of them were not properly guarded against, either in the USA, which led the world into the nuclear age, or in Canada, which followed an independent path. What I shall do in this paper is to sketch the history of nuclear regulation in our two countries, to point out what I consider similarities and differences, and to suggest that regulatory history, as perceived by a concerned public, has a great deal to do with what is possible today and probable tomorrow, in other words, with public acceptance or rejection of the nuclear option. The U.S. situation As we sow, so shall we reap. In the USA, further expansion of the nuclearpower industry has been almost stymied by government actions that reflect mounting public concern. There is no national storage facility for spent reactor fuel and it has been decided not to reprocess it; consequently, existing power plants are about to choke on their own wastes. Since the Three Mile Island accident, no new nuclear plants have received operating licenses, although several are ready to start up. The uncertainty of future government action has caused the abandonment of plans for a number of new nuclear plants. In addition, many research projects related to medicine and agriculture, which produce low-level radioactive wastes, are about to be shut down for lack of licensed disposal facilities. Some would maintain that this situation has come about because of the low benefit-to-cost

Jan 1, 1980

By Brenda J. Morrison

Anything to do with radioactive waste disposal in these days is regarded in a very negative light and with the thought that no possible good could come of anything connected with it. However, it should be remembered that the Austrian government's disposal of some tailings from the Joachimsthal mines resulted in what was probably the most important scientific discovery of this century. In 1898 the Austrian government agreed to give a Polish research assistant working at the School of Physics in Paris one ton of tailings to enable her to carry on her research. Her meagre stipend and the lack of a research grant did not allow her to purchase the ore which was relatively expensive. The uranium oxide in it being used to colour the famous Czechoslovakian glassware. As we all know, from this ton of ore Marie Curie by her own physical labours extracted one gram of radium. When she started this research she was pregnant with her first child. Nothing of course was known at the time about the biological effects of radiation. Very shortly, of course, the acute effects such as skin burns were observed but it was some years before the chronic effects were noted. It is impossible to estimate to what cumulative amount of radiation that Marie, Pierre and their daughter Irene were exposed but it must have been enormous and it took its toll. Marie complained for many years of fatigue and exhaustion and at one point she was seriously ill with some kidney problem which was probably due to toxic effects of ingestion of uranium. She lived until she was 67, however, and died of leukemia. Her eldest child, Irene, who carried on her work, did not live as long; she died of leukemia at 57. The other daughter, Eve, related how her mother and she went on a skiing holiday not many years before her death, and how her mother at this time would swim 300 meters at a stretch. (Curie, 1937). This suppleness of limb could have been due to the anti-inflammatory action of radiation. Even today, patients in France with certain types of rheumatic conditions are treated with injections of radium, where other anti-inflammatory drugs such as aspirin or cortisone have not worked. (Bertrand, Legras and Martin). All this anecdotal information is just to point out that it is an ill wind that blows no good. The risks connected with uranium waste disposal and tailings piles are

Jan 1, 1980

The Mining Foundation of the Southwest (MFSW), located in Tucson, AZ, will hold its 16th annual American Mining Hall of Fame Awards Banquet Saturday, Dec. 5,1998. The Hall of Fame recognizes outstanding contributions to the mining industry by selected individuals and industry partners. Each year, one living award recipient and up to two mining history honorees are chosen by the , Hall of Fame Committee and the Board of Governors of the Mining Foundation. In 1989, the Mining Foundation initiated a Medal of Merit to recognize outstanding individual, technical and professional contributions to the mineral industry. In 1995, an award was created to recognize contributions made by companies and organizations in partnership with the mining industry. This year's inductee, guest of honor and featured speaker will be Charles G. Preble, president and chief executive officer of Southern Peru Copper Corp. He is being recognized for outstanding performance as an executive of an American company operating under difficult circumstances in a foreign country. The Hall of Fame will induct H. Myles Jacob, former chairman and CEO of Inspiration Copper Co., for innovation and farsightedness in matters pivotal to the cop- per industry of his time. In addition, John Cromwell Lincoln, former president and chairman of Bagdad Mining Co., will be inducted for his outstanding contributions to the American mining industry. These contributions include metallurgical research and development of the Bagdad Mine as well as pioneering innovation in the electrical industry. Medals of Merit will be awarded to David N. Skillings, editor and publisher of Skillings Mining Re- view, for his dedication and support of mining interests. J. Ruben Velasco Rodriguez will also receive a Medal of Merit. He is economic geologist, professor and former secretary of the board of directors and secretary general of Compania Minera de Cananea. His medal is for fostering excellent relations between Mexico and the , United States in mining geology and management and for advancing the professional development of others in the field of earth science. An Industry Partnership Award will be presented to Stephen Bechtel and the Bechtel Corp. in recognition of Bechtel's 100th anniversary and the company's outstanding service to the mining industry. The banquet will be held at the The Westin LaPaloma in Tucson beginning with cocktails at 6:30 p.m. Tickets are available from Clare A. Roscoe, manager, Mining Foundation of the Southwest 520-577-7519, fax 520-577-7073.

Jan 1, 1998

By W. H. Pailes, V. Castranova, K. Van Dyke, J. H. Kang

Recruitment and activation of phagocytic cells after inhalation of occupational dusts has been implicated in the development of pulmonary inflammation, fibrosis, or emphysema. Plateletactivating factor has been described recently as a potent inflammatory agent. The objective of the present study was to investigate if platelet-activating factor might play a role in the inflammatory response of the lung to occupational dusts. In vitro exposure of alveolar macrophages to cotton dust (4 mg/ml), silica (10 mg/ml), or coal dust (10 mg/ml) results in the release of picomole levels of platelet-activating factor with a potency of cotton dust > silica > coal dust. Time course studies indicate that platelet-activating factor release from alveolar macrophages is maximal approximately 10 minutes after in vitro exposure to silica. In vitro, platelet-activating factor is a direct stimulant of polymorphonuclear leukocytes increasing chemiluminescence 2.3 ± 0.3 fold above control. The maximal response occurs in the dose range of 10-10 to 10-7M platelet activating factor. In addition, plateletactivating factor potentiates the response of polymorphonuclear leukocytes to a second stimulant; i.e., chemiluminescence generated from polymorphonuclear leukocytes exposed to plateletactivating factor (10-9M) plus chemotactic peptide (FMLP, 10-9M) is 88 ± 22% greater than the sum of the separate effects of these stimulants. In contrast, platelet-activating factor is not a direct stimulant of alveolar macrophages in vitro, having no stimulatory effect on chemiluminescence or superoxide anion release even at levels of 10-6 to 10-5M platelet-activating factor. However, platelet-activating factor (10-5M) does potentiate zymosan-stimulated activation of chemiluminescence and superoxide release from alveolar macrophages by 117 ± 56% and 30 ± 4%, respectively. In conclusion, these data indicate that exposure of the lung to occupational dusts results in the release of platelet-activating factor which may activate polymorphonuclear leukocytes and potentiate the responsiveness of alveolar macrophages to dust. The net result would be pulmonary inflammation and hypersecretion of reactive species by pulmonary phagocytes which could lead to tissue damage and pulmonary disease.

Jan 1, 1991

By J. H. Tylczak, R. Blickensderfer

Impact and abrasion properties of various commercial US grinding halls were evaluated and compared by the Bureau of Mines, US Department of the Interior. Laboratory tests were conducted on balls obtained from eight major US manufacturers. The halls included forged steel, cast steel, and alloyed white cast iron and were subjected to repeated impacts until they broke or until 300,000 impacts were exceeded. Pin abrasion tests also were conducted. The results showed wide differences in impact lives, ranging from a few thousand to over 500,000 impacts. The life of inferior commercial halls was increased five to six times by a laboratory tempering heat treatment. For halls that did not break, the major impact wear mode was spalling and ranged from an average rate of 0.28 to 4.46 mg per impact. The softest halls (steel) had excellent impact resistance but low abrasion resistance. The abrasion resistance of the steel halls generally increased with hardness. The alloyed white cast irons had about twice the abrasion resistance of the steel halls. Users should become aware of the wide variations among commercial halls, and ball manufacturers should be aware that their product can he improved.

Jan 1, 1990

By D. Gu, B. Lin

Discussion of concept Breakage of rock by machine is one of the major methods of excavation. With the development of modern engineering techniques, the advantages of using this method have become even greater. Improving efficiency and reducing the cost of rock breakage is the main goal of mechanizing the rock-breaking operation. For a given stratum, the efficiency of a machine excavation depends, to a large extent, on the design and method of application of the tools used. In a planetary cutter head, the subcutter heads move like planets around the main drive shaft. The general structure of the cutter head is shown in Fig. 1. As shown in this illustration, the main drive shaft (1-1) is connected to the tie bar (1) and, thereby, to a gear (5) that meshes with a fixed-gear ring (2). The subcutter head (4) is rigidly connected to the gear (5) by the subcutter-head axis (2-2). When the main drive shaft (1-1) rotates, the subcutter head (4) rotates around the axis (2-2), under the action of the tie bar and with the help of sleeve pipe (3). At the same time, axis (2-2) also rotates around the main shaft (1-1). As shown in Fig 1, [a] is the angle between the main shaft and the subcutter-head axis. This angle determines the shape of the drilling face. If [a] equals zero, the drilling face will be a flat surface (Fig.1 (a) ), and if [a] is greater than zero, the drilling face will be a spherical surface (Fig. I (b)). For a planetary cutter head, the most important design parameter is the transmission ratio (i), which is defined as [i = (0210)1(1)] Where [(a] is the angular speed of rotation of the subcutter heads around their individual axes, and [o] is the angular speed of rotation of the subcutter-head axes around the main shaft. In Eq. (1), i is positive if the direction of rotation of a subcutter head around its axes is the same as the direction of rotation of the subcutter-head axes around the main shaft (see Fig. 1(b)). Conversely, i is negative when the two directions are opposite (see Fig. 1(a)). When i is positive, the cutters on the subcutter heads form epicycloid paths on the drilling face, as shown in Fig. 2(a). Conversely, if i is negative, the paths will be hypocycloid, as shown in Fig. 2(b). It should be noted

Jan 1, 1996