Search Documents

By William E. Wallace, Michael J. Keane

This review summarizes three sets of ongoing studies which we are performing in collaboration with a number of researchers associated with the Dept. of Interior - Generic Mineral Technology Center for the Study of Respirable Dusts, concerning surfactant-particle interactions studied using this surrogate surfactant. These topics are: (A) the suppression of mineral particle cytotoxic potential by DPL adsorption and the persistence of this effect under conditions of enzymatic digestion; (B) surfactant suppression of organic particle cytotoxicity by DPL adsorption and the effect on subsequent expression of genotoxic potential; (C) potential effects of surfactant on heterogeneous structured complex respirable particles. The references list some of our reports which can provide additional information on these studies. Further, those reports provide references to the literature of the field and to the works of others on these topics. Deep lung airspaces, the pulmonary alveoli and respiratory bronchioles, are coated with a hypophase which is rich in surfactant biomolecules secreted by the alveolar type II epithelial cells. The surfactant is known to be critical to maintaining stable low surface tensions on the inner surfaces of the alveoli by forming a surfactant layer on the airliquid interface of the alveolar hypophase. Upon deposition in the acinar regions of the lung a respired particle's initial contact will be with this surfactant coating over pulmonary tissue. A primary component of this surfactant is the phospholipid diacyl glycerophosphorylcholine, commonly called lecithin. A surface layer of dipalmitoly lecithin on saline will act much as full pulmonary surfactant in decreasing surface tension and producing a hysteresis in surface tension behavior with surface area. We have used dipalmitoyl glycerophosphorylcholine, or dipalmitoyl lecithin (DPL), a major component of that surfactant, dispersed in physiologic saline as a surrogate for studying interactions of both mineral and organic respirable particles with pulmonary surfactant and consequent effects on particle toxic behavior. A. DUST CYTOTOXICITY AND LECITHIN SURFACTANT ADSORPTION Respirable quartz and kaolin clay particles are found to be comparably cytotoxic in a number of in vitro bioassays including lavaged rat pulmonary macrophage release of cytosolic and lysosomal enzymes, and red blood cell hemolysis as a measure of dust membranolytic potential. These direct and prompt cytotoxic activities do not account for the distinctly greater potential for quartz to induce pulmonary disease. When respirable quartz and kaolin are incubated with a dispersion of DPL in saline at 37C it is found that the prompt cytotoxicity of both dusts is fully suppressed as measured in vitro by pulmonary macrophage release of lactate dehydrogenase, beta-N-

Jan 1, 1991

By K. Hanumantha Rao, K. S. E. Forssberg, A. Vidyadhar

Using pure albite and quartz minerals, the separation of albite from quartz using mixed cationic/anionic reagent schemes is assessed through Hallimond flotation, zeta potential and diffuse reflectance FTIR studies. The reagent schemes are tested in bench-scale flotation for the separation of albite from Greek Stefania feldspar ore. The single mineral flotation tests showed the feasibility of selective albite flotation from quartz at around pH 2 using a mixture of cationic diamine and anionic sulfonate collectors or a combined cationic-anionic collector of diamine-dioleate. In contrast to the selective flotation response of albite at pH 2, where albite is slightly negatively charged and quartz possess zero charge, the zeta potential and FTIR studies elucidate similar adsorption behavior of mixed collectors on both of the minerals. The infrared spectra not only showed the co-adsorption of anionic sulfonate or oleate with diamine on the surface but also showed that the diamine adsorption increases with the presence of anionic collector. The intrusion of anionic collector in between adjacent surface alkyl ammonium ions decreases electrostatic head-head repulsion, thereby increasing the diamine adsorption by increasing the hydrophobic tail-tail bonds. The discrepancy in the flotation and adsorption results at pH 2 is attributed to the coarse and fine size particles employed in these studies, respectively. The comparable adsorption on fine particles of albite and quartz at pH 2 is explained by the interaction of ammonium ions on silanol groups by hydrogen bonding besides electrostatic interactions. The bench-scale flotation results indeed showed that selective albite flotation takes place only after desliming the feed material. An albite concentrate exceeding 10% (by weight) Na20 is produced from a material containing about 6.5% (by weight) Na20, where an albite product of more than 9% (by weight) Na20 is considered to be valuable. Key words: Flotation, Adsorption, Zeta-potential, FTIR

Jan 1, 2003

By Carl D. Broadbent

The goal of slope mechanics is to achieve efficient and safe pit slopes. In the case of ultimate mine slopes the objective is to minimize the stripping ratio by steepening the slopes to their maximum stable limit. On the other hand, the inclination of working slopes is normally established by operating space requirements and the function of slope mechanics should be the continuous surveillance of slope conditions to assure long-term stability and to provide timely warning of impending slides so that corrective measures may be incorporated in production planning. In 1956 Kennecott instituted a program to provide the resources necessary to develop and maintain a slope mechanics capability, including technical knowledge, engineers, and instruments. Although the goal has not been fully achieved, very significant progress has been made. Other papers (3, 4, 7, 8, & 12) have described the purposes and detailed results of the most recent study carried out at the Kimbley Pit. The study has provided valuable experience and has given the industry a three dimensional picture of the stability variables that influence a mine slope. The study has better defined those areas which require further investigation and has indicated those design and analytical techniques which can be used with confidence. In effect, the study has paved the way for the next step; that of refining the design process and applying it for profit.

Jan 1, 1968

By Charles G. Weakly, Alan M. Lander, Pamela B. Zohar, Robert W. Leonardson

The cluster of gold deposits at the Goldstrike property is located in the Northern Carlin Trend in northeastern Nevada (Fig. 1). At many mature mining camps like Goldstrike, exploration innovation and success may wane with time. In this regard, sufficient exploration drilling was conducted in the area immediately north of the ultimate pit crest and under the final planned pit wall to test for a major deposit. No indications of large deposits were found, however, the majority of drill holes did intercept mineralization. Mining along the northern pit wall exposed significant structurally controlled ore-grade mineralization that had been missed by exploration drilling. In 2002 and early 2003, the mine geology group added reserves to the pit and improved the definition of underground resources by targeting specific ore-controlling structures within favorable stratigraphic units by utilizing relatively inexpensive horizontal RC drilling from the pit wall. The widespread occurrence of mineralization to the north of the pit was re-interpreted to be an indication of continuity of these mineralized zones. In January 2003, 70 feet of 0.332 opt Au at a depth of 710 to 780 feet was intercepted in a dewatering well. This intercept was significantly thicker and higher-grade than average for the area, which confirmed the existence of high-grade structural continuity, and helped secure management support for additional exploration. A timely and cost effective solution was needed to confirm the potential of the area. Immediate follow-up drilling on tighter grid spacing was rejected in favor of improving the geology model. Exploration across the property would benefit from an improved geology model, but to provide results in a timely manner, the area to the north of the Betze pit was chosen as a starting point (Fig. 2).

Jan 1, 2005

Production In 1993, it was estimated that United States mine production of barite increased 24%. Barite consumption, either sold or used by grinding plants, increased by 39% and imports increased 4%, according to the US Bureau of Mines (USBM). Nevada continued to be the leading producer of barite with 80% of the total, followed by Georgia. It is estimated that 83% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 17% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Prices The value of domestically produced barite, f.o.b. mine, decreased 1%, according to the USBM. The declared value c.i.f. US port of all imported crude barite during 1993 decreased from $40.09/t ($36.37/st) in 1992 to $37.72/t ($34.22/st). Uses Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This included barium chemicals, fillers in paper, plastics, brake shoes and glass. The tonnage consumed in the drilling fluids market increased due to the higher average rig count during 1993. The average number of rotary rigs operating in the United States was 754, 5% greater than the 1992 average of 717. Imports Crude barite imports in 1993 were 443 kt (488,000 st) greater than 1992, representing an increase of 137%. Imports accounted for 67% of the barite consumed (apparent) in the United States.

Jan 1, 1994

By G. Davey

High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. The operating experience of two existing copper operations will be covered to show the effect of the introduction of the Metso Stirred Media Detritor (SMD) a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from the introduction of this new technology. The benefits and process difficulties are covered and explained.

Jan 1, 2003

By Y. C. Kim

For the past quarter of century, much more effort and research have been expended in developing the "optimum" ultimate pit limit design algorithms and much less to solving the "optimum" open pit production sequencing. However, the potential economic benefit to an operating mine is far greater for the latter than the former. Unfortunately, the problem of "optimum" open-pit production sequencing has not been fully solved to date. This paper first reviews the past and currently used methodologies for developing this sequence. The staggered pit phase geometry problem of advanced stripping and operational constraints such as ore and waste tonnage requirements by period and necessary contiguity of mining faces are the main reasons why the "optimum" production sequencing problem has not been solved as yet. This paper also explains why any method which attempts to simplify the problem using ultimate pit limit design algorithm will fail to reach an "optimum" solution.

Jan 1, 1994

By K. Nielsen

The Norwegian tunnelling industry has made remarkable improvements both with regard to productivity and cost efficiency over the last 30-40 years. This development has been made possible by continuous improvement driven by innovation. Based on a generic description of the innovation process and the innovation system, the paper has used the development of modern tunnel drilling in the Norwegian tunnelling industry to discuss the characteristics of its innovation system with a focus on human capital issues and knowledge management.

Jan 1, 2006

By Malcolm Reeves

The heavy oil reservoirs of Alberta and Saskatchewan include sequences of unconeolidated silts and fine sands which respond in an unusual manner when subjected to the high temperature and pore-fluid-pressure associated with steam injection and other thermal enhanced recovery techniques. Apparent transient connections are suddenly established between producers and injectore and there is an associated enhancement in oil (and sand) production. These phenomena have been attributed to local fluidization and piping processes which are known to occur in situations where high pore-fluid-pressures prevent the mobilization of intergranular friction. These breakdown processes may be associated with the penetration of tongues of the heated reservoir fluids with suspended sand into the creep sensitive intact reservoir since the viscosity ratios are sufficiently high for viscous fingering instability of the fluid-fluid interface. A program of laboratory tests has been carried out to measure the strength characteristic of saturated oil sands at a variety of temperatures and fluid pressures. These tests suggest, that in common with the coarser Athabasca sands, the Waseca sands have very little cohesive strength and show the characteristic dilational failure response of dense sands. Some special tests, devised to determine the relative ease with which samples can be fluidized, confirm the expected susceptibility of the fine- sand silts. Both piping and fluidization can be readily induced at in-situ reservoir temperatures and pressures. Analysis of stresses around wellbores suggests that fluid-pressure gradients may be sufficient to initiate piping and that backward erosion along streamlines may link producers and injectors. Such pipes may act as well “adits” gathering oil from the heated reservoir and contributing to enhanced production rates. Mechanical breakdown of the reservoir by drilling, injection and production processes provides a consistent possible explanation for the sand-cut response of production wells.

Jan 1, 1986

By James A. Brierley

The author has known Professor Wadsworth since the 1960s, when interest in the application of microbial technology for metallurgical processes was beginning its rapid rise. The development of bioleaching and mineral biooxidation was advanced, in part, by Wadsworth's belief in the potential for its application, as well as by his numerous contributions to the understanding of the fundamentals of hydro-metallurgy. Wadsworth is recognized for fostering research and development of the field and adding credibility to microbiological-based metallurgical processes, now often referred to as biohydrometallurgy. This Wadsworth Award is recognition of the field of biohy-drometallurgy. It is an honor to serve as a representative for all those individuals involved in research and commercial development of this technology. Modern commercial application of biohydromctallurgy began with the bioleaching of copper from submarginal-grade. run-of-mine material. Kennecott Copper successfully developed this process in the 1950s at the Bingham Canyon Mine in Utah. Other mining operations around the world followed Kennecott's lead. Today, dump bioleaching remains a very low-cost process for scavenging copper from rock that cannot be economically processed by any other method. Despite the commercial success of dump bioleaching, little effort has been made to enhance the micro Biological component of this leach process. Expansion of biohydro metallurgy into recovery of other metals did not occur until the mid-1980s, when the first commercial plant for the pretreatment of refractory gold-bearing concentrate was commissioned at the Fairview operation in south Africa. Now, processes for copper bioleaching and refractory gold pretreatment are engineered specifically to promote the activity of the microorganisms. This paper reviews the current state of commercial applications of biohydrometallurgy. It examines potential future developments and portrays the role of the microbiologist in facilitating continued growth and commercial acceptance of the technology. The commercia1 examples in this paper illustrate the expansion of microbial processing in the mining industry during the last 20 years. Copper bioleaching Early commercial applications of bioleach technology involved processing submarginal-grade, copper- bearing, run-of- mine rock in dumps. Recent applications of the technology use engineered bioleach heaps. Currently. all of these operations are in the Southern Hemi-

Jan 1, 2000

By John W. Wilson

Every operation connected with the working of a deep-level mine has, to a greater or lesser extent, a direct bearing on the costs of production, and hence, profitability of the mine. If adequate mine planning is not done in the early stages in the life of a mine, considerable expenditure can result from the cost of maintaining mine service tunnels, production delays in stopes caused by poor strata control, distortion of fittings in hoisting shafts, rockbursts and so on. In fact, the optimum profitability of a deep-level, hard-rock mine can only be achieved if the layout of the shaft systems, ore passes, tunnels, stoping areas and other underground excavations are designed to withstand or accommodate the rock stress conditions that will be created by mining operations. In South Africa where the deepest mines in the world are located, access to the underground workings of most deep-level gold mines is via vertical shaft systems and a network of tunnels connecting the shaft systems to the stoping areas. In current practice, there are two basic methods of extracting the gold-bearing reef,* namely, the scattered stoping method and the longwall stoping method. The choice of the stoping method is governed largely by the anticipated gold distribution and payability of the reef in the area, the geological conditions, the degree and complexity of faulting and dyke intrusions, the depth at which the gold-bearing reef is to be mined and the inclination and width of the reef. The longwall system was first introduced at the East 717 Rand Proprietary Mines Limited in 1942 in an effort to combat the rockburst hazard which appeared to increase with increase in depth. This mining method became standard practice on that mine for stoping operations 700 ft. below the surface. Since that date, several deep mines on the Central Rand, East Rand and West Wits gold mining areas have adopted this method.

Jan 1, 1977

By Alan T. Nelson, Ronald D. Mariani

The Tilden concentrator was originally constructed in 1974 for the processing of low grade hematite. Flotation is a key concentrating process in the operation, and therefore flotation optimization has been a major concern since the plant startup. This paper will discuss some of the modifications made in the process to achieve optimization. The conversion that now enables the plant to process magnetite as well as hematite also will be discussed. INTRODUCTION The Tilden Mine, located in Ishpeming, Michigan, is managed by Cleveland-Cliffs Iron Company and is owned by Cleveland-Cliffs and two Canadian steel makers. It was constructed and started production in 1974 and expanded in 1979 for processing a low grade, fine-grained hematite iron formation for which there was previously no technology available. Several papers have been written describing the unique character of the concentrating operation. The hematite plant consists of 12 grinding and concentrating lines, which utilize two stages of autogenous grinding with crushing of an intermediate sized product. The ground product is deslimed in a highly dispersed alkaline environment to reject silica. Corn starch, the flocculant, has a high affinity for iron at the operating pH range of 10.5 to 11.0. The ore is upgraded from 35% to 45% iron in the desliming step. The deslime thickener underflow is the feed to flotation. Each flotation line consists of a bank of 10 rougher cells, followed by four scavenging banks incorporating 5, 4, 3, and 3 cells each. The Wemco flotation cells are each 14.1 cubic meters (500 cubic feet) in volume. A total of 12 flotation lines are available. [ ] A reverse flotation process is employed, using a straight-chain, 8 to 10 carbon primary ether amine silica collector. At the levels used in the circuit, the amine also serves as a frother. A final concentrate is produced in the rougher cells. The concentrates from the four scavenging steps are combined and recirculated to the feed end of the roughers, with the fourth scavenger froth being discarded as a final tailing. Upgrading to about 65% iron is achieved, with control of the circuit based on final concentrate silica grade. Starch is again used, this time as a depressant for iron. During the years of operation, several key areas of the flotation process have been targeted for optimization. The most significant improvements have been realized in the following areas: *Grade Control Automation *Control of Water System Chemistry *Flotation Spray Water This paper will focus on these areas, but other minor improvements also will be briefly discussed.

Jan 1, 1993

By H. A. von Schonfeldt, H. Douglas Dahl

INTRODUCTION During the past decade, significant pro¬gress has been made in applying rock mechanics principles to mine design problems by a great number of researchers. Some of these new techniques have found their way into the engineering and planning offices of the operating mine. In spite of these advances, however, the application of rock mechanics in the day-to-day mine planning and design of our domestic coal mines is rela¬tively rare. There are a number of reasons responsi¬ble for this relatively slow progress, not the least of which is the question of how to measure the success or cost effectiveness of a sizable rock mechanics effort in an opera¬ting mine. Firstly, the properties of geologic materials generally vary over a wide range and it is, therefore, difficult to assess whether an improvement in the mining conditions is due to a design change or due to a change in the geologic conditions. A second reason for the slow acceptance of rock mechanics in engineering thinking is the fact that some of the concepts are quite difficult and that physical evidence of their validity to mine design is still rare. Thirdly, com¬munication between research, engineering and applications oriented people appears to function only intermittently. In our view, however, the most important impediment lies in the "state-of-the-art." Exactly how much can rock mechanics help the mine operator? The best that rock mechanics can do at present is determine whether one approach is better than another when weighed against some design objective (stress, strain, deformation). We cannot determine the abso¬lute best ground control design -- only what is better. If ground control is lost, the statement that "it's the best one we looked at" means very little to the harried operator. While the "state-of-the art" has advanced a great deal, it has certainly not been reduced to an engineering matter in that design hand¬books are available -- they are not. The success of a rock mechanics program, there¬fore, can be determined only over a long period of time of continuous effort.

Jan 1, 1977

By Donald A. Brobst

The minerals barite (BaSO, -barium sulfate) and witherite (BaCO, -barium carbonate) are the chief commercial sources of the element barium and its compounds, whose many uses are nearly hidden among the technical complexities of modem industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry, which in 1990 consumed about 90% of the world's production of 4.9 Mt as a major ingredient of the heavy fluid called mud that is circulated in rotary drilling of oil and gas wells. The remaining 10% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite is found throughout much of the world and is available from three major geologic types of deposits-vein and cavity-filling, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase because of the world's need for oil and gas. Geologic circumstances are favorable for the discovery of new deposits of commercial value. Witherite, desirable as a raw material for the production of barium chemicals, is much less common and abundant than barite.

Jan 1, 1994

By R. L. McNearny, K. A. Barker

Four numerical models written with the "PFC2D " program were compared against four similar physical models. The numerical models were constrained numerically to closely follow the caving behavior of the physical models. Results from the numerical analyses closely simulated both the granular and blocky behaviors of the physical models, including bridging and interlocking of the simulated orebody during draw. The drawdown patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. The same assumptions and governing parameters used in analyzing the first four models were applied to an additional model. The fifth model employed a completely different, uneven, draw sequence than the other four models, allowing the material to flow in a more granular manner with a demonstrated instability of the undercut sections between each drawpoint opening. Drawdown patterns and behavior of the numerical material of the first four models progressed at uneven and inconsistent rates, similar to those seen in the physical models. By inspection, the overall shape and flow lines of both the numerical and physical models were close in the area removed and in the flow characteristics. The fifth model proved to be the most unstable of all the models tested, with poor correlation to the physical models. The uneven draw sequence, coupled with an additional frictionless wall condition and an added drawpoint, caused the material to flow in a very granular manner. Information generated by this study can be used as a first approach in determining the proper draw rate, drawpoint spacing and undercut thickness for a block-caving operation. Numerical models are often difficult to predict and interpret. However, this study should increase the confidence level for use of the PFC2D program in the future.

Jan 1, 2000

By Paul L. Russell, Charles O. Hook

While the oil shale resources of the US are becoming increasingly known, few people in this country are aware of the extensive worldwide occurrence of this resource. Two recent international conferences* confirmed the growing worldwide interest in oil shales, both as future and current energy sources. The 1981 conference noted the difficulty in characterizing worldwide oil shale resources because of lack of common terminology in reporting both assay value and resource potential. Assay value is variously reported as: •US gallons per short ton; •Imperial gallons per metric ton; •Liters per metric ton; •Liters per cubic meter; •Weight percent oil; and •Volume percent oil. Oil shale resources are variously reported in barrels, short tons of oil shale, metric tons of oil shale, and cubic meters of shale oil. Worldwide petroleum shortages sparked interest in alternate energy resources including oil shales. While petroleum supplies appear to have stabilized, at least for a while, high costs are affecting the balance of payment index of many countries, resulting in a continued search for local energy resources. Kerogen is the organic constituent of oil shale and may be the most abundant form of hydrocarbon on earth, possibly exceeding coal occurrences and far more abundant than naturally-occurring petroleum resources. Oil shale, by one name or another, is widespread and is known to exist in more than 38 countries (Table 1). Oil shale industries have existed in at least 14 countries at one time or another. Many predated the Drake oil discovery in Pennsylvania in 1859, and most were unable to compete with natural oil; these operations either converted to its use or closed. At the present time shale oil is being produced on a commercial scale only in the USSR and in China. Only very rough estimates of grade and quantity are available for most of the worldwide shale occurrences since only a few deposits have been thoroughly explored. The Green River Formation of Colorado, Utah, and Wyoming is an exception. For many years this oil shale deposit has been described as the largest single concentration of hydrocarbon material in the world. With increasing world interest, larger deposits may yet be found. In 1965, the US Geological Survey published an in-place world oil shale estimate. This study, while made some 16 years ago, is still a reasonable order-of-magnitude estimate. Although exploration and evaluation are underway and a few oil shale deposits have been appraised, information on which to evaluate most worldwide oil shale occurrences has improved little since 1965. Table 2 presents an order-ofmagnitude estimate of in-place world oil shale resources. Total US resources and Green River Formation

Jan 1, 1982

By Wolfgang Pietsch

Roller presses were first invented in the middle of the 19th century, for the economical size enlargement of coal fines as fuels. Coal briquettes became quickly accepted for industrial and domestic use giving rise to a large and sucessful industry, particularly in Europe, Japan, and North America. When, towards the middle of the 20th century, coal was more and more replaced by other energy sources, such as electricity, gas, and oil, roller press manufacturers searched for alternate applications of this equipment. In addition to contemporary coal briquetting, in fields such as smokeless fuel and form-coke, it was found that redesigned and modernized roller presses, which are now capable of exerting high forces, are versatile machines for many tasks in mineral processing. Today they are used for: - the "classic" pressure agglomeration and - the "new" high pressure comminution. In pressure agglomeration, the characteristics of fine minerals are improved by forming briquettes or granulated products from compacts. During size enlargement with roller presses briquettes are directly obtained while granular materials are produced by crushing and sizing of compacted sheets. The processes are carried-out essentially dry and often do not require binders other than those inherently contained in the feed and "activated" by the high forces and/or elevated feed temperatures (e.g. hot briquetting). Therefore, no foreign materials (impurities) are added. Another advantage of the technology is, that wide particle size distributions are acceptable or desirable as feed materials, including millimeter or even centimeter sized particles. Plastic particles deform and brittle materials are crushed during pressure agglomeration. A relatively new application of roller presses in mineral processing is the utilization of the crushing effect when brittle materials pass the nip area between the rollers. It was found that this crushing mechanism is very efficient thus saving energy, particularly in grinding circuits handling large capacities. The paper introduces the fundamentals of the process and describes the design as well as applications of modern roller presses in mineral processing.

Jan 1, 1995

By Gail L. Achterman

Most mining companies today perform site assessments and operational or compliance audits regularly. The purpose of these audits is to review company facilities and operations to determine whether they comply with applicable federal, state and local environmental laws and regulations. Why Audit? Companies adopt assessment and audit programs for legal and business reasons. The business reasons include: (1) ensuring efficient and cost-effective compliance through early problem identification and resolution; (2) planning and implementing business transactions such as real estate conveyances, loans, mergers and acquisitions, and waste disposal service contracts; and (3) employee training and relations. Legal reasons for audits include: (1) avoiding enforcement actions and penalties; (2) meeting environmental permit certification requirements; (3) avoiding corporate officer liability; and (4) meeting Security and Exchange Commission disclosure requirements. The Environmental Protection Agency ("EPA") encourages environmental auditing by regulated entities. The EPA Environmental Auditing Policy Statement was published in the Federal Register on July 9, 1986 (51 Fed Reg 25,004). Although the existence of an auditing program does not create a defense to or otherwise limit a company's regulatory responsibilities, EPA considers compliance programs in setting inspection and enforcement priorities. If a company makes an honest effort to identify and correct its own problems, EPA's enforcement approach is influenced, especially if violations are promptly reported. Perhaps more significant to many executives, the U.S. Department of Justice issued guidelines last year on when it will pursue criminal prosecution for environmental violations. See Department of Justice, "Factors and Decisions on Criminal Prosecutions for Environmental Violations in the Context of Significant Voluntary Compliance or Disclosure Efforts by the Violator," (July 1, 1991). It is now commonplace to read about major companies pleading guilty to criminal violations and paying millions of dollars in penalties. For example ALCOA recently agreed to pay criminal fines and civil penalties totaling $7.5 million for unauthorized excavation of PCB-contaminated soil and improper dumping of spent caustic solution. No executive wants to explain to the Board of Directors or shareholders why the company was criminally indicted. The Department of Justice considers factors such as voluntary disclosure, preventive measures and compliance programs, such as a regular compliance auditing program, the effectiveness of the disciplinary system for employees who violate the company's environmental policies, and subsequent compliance efforts by companies to remedy ongoing noncompliance. The Department of Justice looks closely at whether audit recommendations were implemented in a timely way and whether environmental compliance was a standard by which employees were judged. The Lawyer's Role. The role of the lawyer in an audit team deserves special attention. When enforcement action or litigation has begun or is contemplated or a government agency has asked for information, attorneys always should be directly involved in environmental audits. In most situations, however, environmental audits are management tools, and the attorney's role should be to advise the team. The attorney can help make sure the team understands the laws and regulations the facility must

Jan 1, 1992

By David Pentz, Paul Hodges

GENERAL INTRODUCTION The object of this paper is to discuss those aspects of open pit mine design which are affected by geotechnical factors. The temptation exists for some practitioners of geotechnical engineering to believe that this relatively new engineering discipline is the ‘be all and end all of mining.’ In the opinion of the authors, this is fallacious but, as our ability to put numbers to the behaviour of rocks and soils improves, it is clear that geotechnical engineering will become an integral and important part of designing and operationg mines success- fully. Open pit mines in the context of this paper also includes open cast mines, where the 'ore" is extracted and the waste material is immediately replaced or ' backfilled in the mined portion of the pit. Open pit mines operating today move from very small tonnages a day to in excess of 400,000 tons per day. Several mines are operating and are being designed to capital expenditure for such projects in some cases exceeds five hundred million dollars and in a few cases will exceed one billion dollars. The size of this investment means that financing will have to be provided from banks or joint partnerships. This financial environment means that planning will be carefully scrutinized by experienced representatives of financial institutions or other mining companies. All too often a project has been put in jeopardy because the personal desire of one or two men to make a project proceed has caused incomplete planning or perhaps in some instances deliberately leading observers 'down the garden path.’ In our opinion the day is rapidly arriving when the quality, logic, practicability and completeness of the planning will make the difference between securing financing or not and, in the cases of existing open pit mines, of the difference between survival and closure.

Jan 1, 1977

By P. R. La Pointe, H. C. Ganow

The production of both over- and undersized coal fragments is a constant problem to open pit operators in the Powder River Basin. Operators strive to achieve production blasts that economically minimize the weight percentage of over- and undersize coal. However, natural fractures influence blast fragmentation, and can impose limits on the final fragment size distribution. ARCO&apos;s Anaconda Minerals Company studied the limits placed by natural fracturing as part of a wider geotechnical study of the Wyodak Coal in the eastern Powder River Basin, Campbell County, Wyoming. Measurements of fracture orientation, size and spacing were made at ARCO&apos;s Black Thunder Mine. These data were used to form statistical distributions for natural fracture size, spacing and orientation. An algorithm was created to select fracture properties at random from these distributions and to form hypothetical blocks. The blocks were then numerically "sieved" to derive pos- sible particle size distribution curves. These curves are compared to fragmentation results from samples taken from three test blasts. All test blasts yield very similar lognormal fragment size distributions. The median particle size varies from 1.25 to 2.0 in.(3.2 to 5.1 cm), the mean from 4.0 to 8.5 in. (10.2 to 21.6 cm). The standard deviation was about 1.6 in. (4.2 cm). Coal fines (fragments < 0.25 in. or 0.64 cm) are about 15%. Calculated fragment distributions for the natural fractures predict the median size well but underestimate the variance. Algorithm modifications to account for processes known to occur in the comminution zone near the blast hole significantly improve the match in the fine coal size range. The match suggests that spacing of fractures, rather than fracture length, controls the formation of fine- and medium-sized fragments. On the other hand, the oversize coal is controlled by the fracture lengths, rather than the spacing. Data from subsequent test blasts support this idea. By increasing delay times from 8 msec to 17 msec, engineers were able to reduce fines to 7% - 10% but could achieve no further improvement, despite changes in shot pattern geometry, decking and hole size. The hypothetical fragment distributions show that, even without blast enhancement, about 5% of the natural coal blocks are fine-sized.

Jan 1, 1986