Search Documents

By J. W. Stevenson

The need for a separate ventilation department within the management team was recognized by the management of U. S. Pipe and Foundry before the company was purchased by Jim Walter Corporation in January, 1970. Because the coal beds of the deep underground coal properties owned by Jim Walter Resources lay 1300 to 2200 feet below the surface, efficient mine ventilation practices are essential through shaft openings varying from 16 to 22 feet in diameter. The extremely high methane gas quantity indicated to be in the coal bed because of the depth of cover and documented by various U. S. Bureau of Mines tests and demonstrated by early mining proved the need to implement this early management decision. At U. S. Pipe and Foundry mine ventilation was a function of the Mining Engineering Department with ventilation personnel assigned to the mine receiving their day to day work assignments from the mine manager or mine foreman. At Jim Walter Resources, the General Manager - Ventilation reports to the Senior Vice President, Mining Engineering, who reports directly to the President, Mining Division, Figure 1 (Company Organization Chart). Position descriptions are static; however positions are dynamic and consequently the degree of emphasis of specific duties and responsibilities change depending not only upon the aptitude of the individual performing the job but also upon his ability to meet the needs of his supervisors; and ultimately upon his ability to react to the economic forces directing our society. The following describes the duties and responsibilities of the General Manager - Ventilation, Figure 2.

Jan 1, 1980

By J. D. Miller, J. Hupka

Environmental applications of the air-sparged hydrocyclone (ASH) technology are presented. The original ASH design used porous sintered steel or porous polyethylene tubes as spargers. To diminish/prevent plugging and to reduce pressure head loss in the gas path a wire screen sparger and new hydrocyclone design have been developed, which allows for wide application of the technology to solve environmental problems and to be used as a chemical reactor. Field and laboratory trials have shown that the ASH technology might be preferred for the stripping of volatile organic compounds WOC) from contaminated water. The ASH has also been developed for absorption of SO2, toluene vapors, and for the recovery of cyanide.

Jan 1, 2005

By Andrew Neale

ERIC GUTIERREZ: With that, we'll go ahead with the final speaker of the day, Andrew Neale. Andrew has a master's of science degree in mineral processing from the University of Alberta. He worked at the Falconbridge in Sudbury area, also at Brenda Mines, and then he became part of the Brenda Process Technology group in British Columbia. He joined Freeport in late 1993 in Indonesia, and was involved in process control and automation. He is now the senior manager of metallurgy in New Orleans. He's responsible for designing Freeport's new 100,000-ton-per-day expansion concentrator, which is currently being commissioned. Please welcome Andrew. ANDREW NEALE: With the ongoing explosion in digital computing power, there seems to be no limit to what can be modeled, simulated, and controlled in the mineral processing plant. However, at each stage of development of a control system, it is necessary to complete a cost-benefit analysis for justifying the move to a higher level of control. Incremental improvements in plant performance, while often significant, must be weighed against the costs of implementation and long-term maintenance. This presentation will provide examples of what the author believes are misplaced or misguided process control efforts and make a case for the KISS principle as applied to process control.

Jan 1, 1998

By Jae-Chun Lee, Kang-In Rhee, D. B. Dreisinger, Hyo-Shin Yu, G. A. Kordosky

The development of a process for direct synthesis of very pure ZnO powders from zinc-bearing waste was investigated. The zinc waste which contains 55% zinc was leached with sulfuric acid. After iron removal by hydrolysis from this zinc solution, purification through solvent extraction by the use of D2EHPA as an extractant was carried out. Then, loaded zinc in the organic solution was stripped and precipitated simultaneously using oxalic acid as a precipitant. Synthesized ZnC2O4 precursors by precipitation stripping were calcined to obtain ZnO powders exceeding 99.9% purity. The effects of sulfuric acid concentration, leaching time, and pulp density on the extraction of zinc were studied and optimum conditions for the solvent extraction were obtained through purification of the zinc solution. The size, morphology, and size distribution of synthesized ZnC204 powders were studied in terms of oxalic acid concentration, temperature, surfactant added, precipitation time, etc.

Jan 1, 1993

By R. H. Grau

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing some practical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers? exposure to airborne contaminants.

Jan 1, 2008

By R. A. Jankowski, J. J. McClelland

Laboratory tests were conducted by the U.S. Bureau of Mines to determine the respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Exhausting face ventilation was varied from 3,000 to 9,000 cfm (1.42 to 4.25 m3/sec). Spray-water-flow was varied from 15 to 35 gpm (0.057 to 0.132 m3/min), while nozzle operating pressure was varied from 80 to 200 psi (5.62 to 14.06 kg/cm2). Results from gravimetric dust samples indicated that airflow had the greatest individual impact on reducing dust levels, with return and operator concentrations reduced by as much as 57% and 99%, respectively. Interactions between dust control parameters were found to be significant. Often, these interactions defined a level of application for a control parameter where further increases in that parameter failed to produce additional reductions in dust concentrations. In several cases, increases in a control parameter resulted in higher dust levels at the operator's location. These higher dust levels were attributed to additional rollback and/or airflow turbulence. Regression modeling indicated that increases in airflow to 8,400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.84 kg/cm2) typically were beneficial at the operator and return sampling locations.

Jan 1, 1991

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduct ion through multilayer (wall and floor of airway consist of several layers of material and rock) and two-surface (dry and wet surfaces) airway wall and airway floor with convective heat and moisture transfer between their surfaces and mine air with time dependent changes of temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for calculation of the surface temperature of any type of surface of airway wall/floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. These solutions are illustrated for the case of general harmonic course of air temperature and humidity. Balance of heat and moisture transfer between surfaces of airway wall and floor and mine air is solved by an iterative method in the partial sections of airway. The temperature and the humidity of mine air on the outlet of each partial section of airway at given time are its resolutions and they are the input data for following partial section. By this way it is possible to solve complicated dynamic changes of mine air temperature and humidity in an air way system by relatively simple mathematical apparat.

Jan 1, 1991

By E. T. Sugar

English China Clays, the world's largest producer of China Clay, has its main production capacity in the South-West of England, where a complex of pits, refining plants, dryers and ports covers an area of approximately 100 square kilometres. The possibility of a computerised information network was first considered in 1980. The system was required to provide information at the central level and also at local plant level to improve co-ordination and control. Immediate access by any authorised user, and flexibility of interrogation were important aims. A small micro-based prototype system was implemented in 1981, and later that year development of the mainframe system commenced. This latter system will provide at least one terminal in every works location and will allow inter-communication of laboratory test data as well as detailed stock levels and production data. An integrated system for order processing will allow stock levels to be monitored in relation to anticipated requirements. The system has been developed by the Data Processing Department using the IDMS database package running on an ICL ME29 mainframe. It was decided to use microcomputers as terminals, which although more complicated because of protocol emulation allows stand-alone applications to be run on the same equipment. Those applications concerning Production Planning are outlined in the paper. Communication on the network is by synchronous transmission over dedicated lines. All data is stored on the central database with terminals accessing it in a star configuration. The system is currently partially implemented with 30 available screens at 18 separate worksites.

Jan 1, 1986

By Shigeru Sarata

Working places in underground mines are formed by digging. The main feature of underground working places is that they are surrounded by rock. Digging through rock, which is main operation of mining, generates great reacting force. In many cases, supports are required to maintain a roof. Working places change their location with progress of mining operation. Therefore, for automate the work in such environment, a locomotive mechanism which can endure great reacting force, can support effectively the roof and floor, and has high moving performance in rough environment, might be required. In narrow underground environment which is surrounded by rock, it is possible to generate great fixing force by means of a jack which is set between the roof and floor or both side wall it is usual to apply a jack as anchor post for fixing machinery or reacting force. Self advancing supports widely used in long wall faces in coal mines could be said an example of locomotive mechanism with propping up fixing method. However it is difficult to say that ordinary self advancing supports have enough adaptability for various condition of the roof and floor. New locomotive method for underground working place 'Swing Phase Locomotion' is proposed. It is achieved by mechanism based on frame type support and synchronous control of jacks. Furthermore, to achieved high adaptability to various conditions of the roof and floor, another walking mechanism has been developed. The mechanism employs propping up jack as its legs.

Jan 1, 1989

By Gustavo G. Pilger, Jair C. Koppe, João Felipe C. L. Costa

Information for mine planning requires to be close spaced, if compared to the grid used for exploration and resource assessment. The additional samples collected during quasi-mining are frequently located in the same pattern of the original diamond drill holes net but closer spaced. This procedure is not the best in mathematical sense for selecting a location. The impact of an additional information to reduce the uncertainty about the parameter been modelled is not the same everywhere within the deposit. Some locations are more sensitive in reducing the local and global uncertainty than others. This study introduces a methodology to select additional sample locations based on stochastic simulation. The procedure takes into account data variability and their spatial location. Multiple equally probable models representing a geological attribute are generated via geostatistical simulation. These models share basically the same histogram and the same variogram obtained from the original dataset. At each block belonging to the model a value is obtained from the n simulations and their combination allows one to access local variability. Variability is measured using an uncertainty index proposed. This index was used to map zones of high variability. A value extracted from a given simulation is added to the original dataset from a zone identified as erratic in the previous maps. The process of adding samples and simulation is repeated and the benefit of the additional sample is evaluated. The contribution of an extra sample was evaluated locally, globally and in terms of variation in total measured resources. The procedure showed to be robust and theoretically sound, mapping zones where the additional information is most beneficial. A case study using coal seam thickness illustrates the method.

Jan 1, 2002

By E. W. Hawk

he power generation industry may be required to reduce carbon dioxide (C02) emissions if regulations related to global climate change are enacted. Coal-fired generation emits more than 80% of the power sector CO2 and would be a likely target for CO2 reductions. Compliance with the Kyoto Protocol will require a 33% reduction from the projected year 2012 emission level, even with moderate load growth. This article describes an analysis of power industry CO2 reduction options and their costs. It assesses how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered. The Global Climate Change Treaty signed at the Rio de Janiero Earth Summit in June 1992 set the long-term goal of stabilizing CO2 concentration in the atmosphere. The December 1997 Kyoto Protocol established short-term mandatory targets for the United States and 37 other developed countries. The United States' target is a 7% decrease by 2012 from the 1990 "greenhouse gas" level. Developing countries are exempted from reductions, according to the Kyoto Protocol, despite projections that indicate a significant increase in their emission levels. The Kyoto Protocol must be ratified by the US Senate. US power industry carbon emissions were 490 Mt (540 million st) in 1990 and are projected to be 680 Mt (749 million st) in 2012, according to the US Energy Information Administration. Coal-fired generation emits more than 80% of the power sector CO2. Assuming that the power industry is only required to reduce emissions by a proportional share, a 33% emission reduction, or 225 Mt (248 million st) of carbon, would be required to comply with

Jan 1, 1999

By G. Bloomsburg, R. E. Williams, S. D. Vincent

A modeling scheme is developed to simulate the hydrogeologic effects of mine design and development in unsaturated rock. Simulations are conducted using the UNSAT2 finite element computer program and hydrogeologic data from the site of a proposed mined-out waste repository at Yucca Mountain, NV. Results of the simulations are analyzed for: •variations in the direction of ground water flow and in the distribution of pressure head caused by the design of the mined out openings; and •mine design variables that affect the predicted rates of mine water inflow. Evaluating the hydrogeologic impacts of mine design and mine development in unsaturated rock is significant in several respects. Characterization of the preemplacement of wastes along the fastest path ground water flow system at the Yucca Mountain site has been a primary research effort. Ultimately, however, the degree to which waste isolation is achieved will depend largely on the post-mining hydrogeologic environment as altered by the mine design and on the radionuclide inventory and resulting heat effects of the repository. Therefore, an ongoing characterization of the proposed mined-out nuclear waste repository at Yucca Mountain, NV, is recommended. Modeling results indicate that: •mined out openings will affect the movement of ground water, both in rate and direction; •hydraulic effects of mine development depend on the hydrogeologic environment and on mine design geometry; •mine water inflow is possible in the unsaturated zone, even for mines developed in hydrogeologically homogeneous rocks; and •mine water inflow can occur at values of down ward flux that are appreciably less than the saturated hydraulic conductivity of the overlying rocks.

Jan 1, 1991

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987

By R. Henley, S. S. Webster, L. Harris

High resolution airborne magnetic and radiometric data have been shown to optimize exploration for epithermal gold deposits in the vicinity of Charters Towers, northeastern Queensland. The radiometric data allow extrapolation of poorly outcropping geology to provide a cost-effective mapping technique, even at exploration scales (eg. 1:25,000). At a regional scale (eg. 1 : 100,000) the magnetic data reflect the regional tectonics and divide the area into domains for the application of different genetic models. For example: 1. the Ravenswood Batholith is characterized by multiple intrusions dating from Ordovician to Permian age. The polarity of the magnetic anomalies implies an age for the intrusions and indicates a deposit style for exploration. 2. extensional and wrench tectonics along the northern margin of the Drummond Basin are interpreted from the magnetic data and indicate favourable blocks for detailed exploration. Genetic exploration models may be tested in favourable environments by the recognition of geophysical signatures. These signatures reflect structural, lithological and alteration patterns arising from controls on ore deposits and can be applied at regional or detailed scales.

Jan 1, 1989

By J. W. III Leonard, T. E. Wilson

In addition to coalbed thickness and basic coal quality data, coal drill cores can produce design data for coal beneficiation processes. To generate design data, a coal drill core should be reduced from its original cylindrical form to a particle size distribution and composition that represents (with the possible exception of top size) a raw coal process stream. Reducing a coal core with a crushing machine rarely accomplishes this representation. This investigation employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis to characterize the core in terms of first-order and zeroth-order break- age rate constants, which are indices of the propensity of the coal to degrade during handling. To reduce composition variables and conserve difficult-to-obtain coal cores, the initial drop-shatter and dry-tumbling tests were done with synthetic cores. Then, cores from three coal beds, Illinois No. 6, Upper Freeport and Pocahontas No. 5, were tested. Comparison of a crushed drill core and a drill core prepared by drop-shatter and tumbling indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed.

Jan 1, 2000

By H. J. Marais, P. C. van Aswegen

The Biological Oxidation (BlOX®) Process for the treatment of refractory gold ores was commercialized in 1988. During the last decade, the technology has developed into a mature, commercially viable process, with five additional operations commissioned, including operations at Sao Bento in Brazil, Harbour Lights and Wiluna in Australia, Ashanti in Ghana and Tamboraque in Peru. With ongoing development, the efficiency and cost effectiveness of the process have both improved, making it an attractive alternative to conventional refractory treatment processes such as roasting and pressure oxidation. The bacterial culture is robust and can withstand the normal fluctuations experienced on an operating plant. The plants are simple to operate, making it ideal for remote areas. The scale-up potential of the process has been proven, and it can be applied to large refractory ore bodies. The process is environmentally friendly. Neutralization of plant effluents produces precipitates that comply with the most stringent environmental regulations.

Jan 1, 2000

By J. A. Hrabik

The feasibility of mining deep phosphate deposits by a borehole mining system was compared with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 46 m (150 ft) or greater. However, at 15- and 30-m (50- and 100-ft) thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasibility of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is used to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1987

By P. C. Kapur

The hierarchical relationship between three broad kinds of grinding models for a spatially homogeneous, linear, time-invariant batch grinding system are first established. Limiting and asymptotic arguments for arriving at approximate but simpler models are employed in all three cases. These parsimonious models -provide alternate and, in some respects, more incisive and convenient tools for the analyses of grinding processes and simulation of comminution circuits. In the discrete-size, discrete- time class of models, a reduced mill matrix is derived, which is seemingly adequate for those grinding circuits whose identification otherwise is difficult because of limitations on the quantity of data and its quality. In discrete-size, continuous-time types of models, parameter lumping has been employed for obtaining a G-H solution which is quite accurate and exceptionally useful for graphical display of data, model verification, and parameter estimation and simulation. In continuous-size, continuous-time models, a similarity transformation is used for solving the integrodifferential equation of grinding. This solution provides a unified framework for a number of apparently diverse empirical grinding phenomena such as self-preserving behavior of ground particle size distributions and energy laws.

Jan 1, 1987

By A. S. Malicsi, Vathsala Rajagopal, I. Iwasaki

Corrosion and abrasion properties of a series of chromium-containing, cast-iron balls, with Cr contents ranging from 0% to 29%, were evaluated and compared with austenitic stainless-steel and mild-steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite, with either 5% pyrrhotite or 5% chalcopyrite, under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynantic polarization curves under abrasion. Flotation recoveries were determined on a 95% quartzite + 5% pyrrhotite sample ground with various cast-iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with flotation results and with corrosive wear data obtained from marked ball wear tests.

Jan 1, 1993

By Pentti Seppanen

The activities of Outokumpu Oy in the mining industry span all branches from prospecting to the production of refined metals and the manufacture of semifinished products. Products include copper, zinc, mercury, cadmium, nickel, cobalt, sulfur, gold, silver, iron ore, stainless steel, selenium, ferrochromium, lead and chromium concentrates, as well as chromite foundry sand. In addition, the activities of Outokumpu Oy extend to development and production of instruments, planning of industrial projects and instrumentation as well as the manufacture of specialized machines for ore concentration. The company now operates ten mines, eight of which are underground and all of which are in sulfide deposits except one. The fully automated monitoring and control of underground mine ventilation at the Pyhasalmi mine are an important technological contribution to the industry. Development work on the ventilation control was started in 1969, and since May 1973 it has operated in a fully automated computer-controlled mode. The Pyhasalmi mine has been in production since 1962, having begun as an open-pit operation. Development of underground mining began in 1967. The present annual production is one million tons all from underground mining. The underground mine is equipped with a main shaft and an auxiliary shaft, and two raises for ventilation. There is also a rampway from the surface to a depth of 500 m. The main shaft is for ore hoisting and the auxiliary shaft is used for waste-rock hoisting and for downcast ventilation. One of the raises is for downcast ventilation and the other is for upcast ventilation. The mining methods employed at Pyhasalmi are sublevel stoping with backfill, sublevel caving, and sublevel shrinkage stoping. Copper and zinc concentrates are produced. The Pyhasalmi mine is highly mechanized with about 4000 installed diesel horsepower underground. The maximum capacity of fresh air is 150 m3/s.

Jan 1, 1979