Search Documents

By A. Shakoor, A. M. Hirt

The compressive strength of coal, and its variation within and between seams, was determined for four Pennsylvania coal seams (Pittsburgh, Sewickley, Upper Kittanning and Lower Kittanning). Large coal blocks were obtained from 12 coal mines (three mines per seam) and cut into 50-mm (2-in.) cubes using a low-speed saw. The cubes were tested for compressive strength, with the results used to compute actual pillar strength. Using the tributary area approach, the pillar stress was determined. The pillar stress and strength data were used to calculate the factor of safety against pillar crushing for each mine. The cube strength was also correlated with various physical and chemical coal properties (density, percent absorption, percent ash, percent sulfur and percent carbon) to see if any strong relationships exist. The coal's mean compressive strength varies from 9.1 MPa (1326 psi) in the Lower Kittanning seam to 37.8 MPa (5480 psi) in the Pittsburgh seam. Between different seams the pillar strength varies from 29.5 MPa to 48.1 MPa (4282 psi - 6981 psi). Although coal strength appears to be weakly related to carbon content, no relationship was found between compressive strength and other physical or chemical properties. Since the values for the safety factor against pillar crushing generally exceed the recommended value of two, the existing pillars are mostly overdesigned. This implies that an accurate assessment of coal compressive strength could result in the use of smaller pillars and, thus, increased coal production.

Jan 1, 1993

By Alice Blount, F. Patrick Carr

The quantitative evaluation,of quartz and other minerals in acid-insoluble residues from carbonate rocks and other industrial mineral products derived from sedimentary and low-grade metamorphic rocks is difficult. Commonly there are a dozen or more minerals present, and the suites vary from sample to sample. Because of these factors, either the absorption coefficient must be determined on a sample to sample basis or an internal standard must be used. Internal standards in general use are unsatisfactory. For example, [A1203] is often present in product samples because of ceramic grinding elements used in their production; CaF and LiF have peaks which overlap or nearly overlap mineral peaks in the samples. A careful evaluation has shown that magnesium aluminate (synthetic spinel) works particularly well as an internal standard for these types of samples. Not only does it have few, strong diffraction peaks which do not overlap, the peaks are in the same 28 region as the minerals, usually quartz and silicates, for which quantification is desired. Spinel also consists of equidimensional particles without prominent cleavages; this promotes a random orientation of the minerals in X-ray diffraction mounts. In addition, spinel can be used to correct for loss of diffracted-beam intensity due to thin sample preparations which are often unavoidable.

Jan 1, 1991

By Malcolm Scoble, Sean Dessureault, Scott Dunbar

Budgets are key financial and behavior drivers for most businesses, including mining. Budgets are used to link strategic objectives to tactical decisions, to measure performance, and to provide basic financial planning. More accurate and pertinent budgets should result in improved strategic decision making and performance measures. This paper discusses how a process based production and cost database, based on activity based costing models and the one year production plan, can be used to create the annual budget for an operating mine as an Activity Based Budget (ABB). A case study is used to compare budgets derived from traditional methods and an ABB approach. It is evident that the ABB method is more accurate.

Jan 1, 2002

By Dalva L. Moellenberg

Introduction Hard rock mine closure (often referred to as decommissioning), mined land reclamation and financial assurance requirements are receiving considerable attention by governments and organizations around the world. In the United States, federal agencies and the states continue to consider and make changes to laws governing mine closure and mined land reclamation, most of which were originally enacted in the mid-1970’s through the mid-1990’s. Internationally, a number of prominent groups and various countries currently are considering new laws, regulations and policies for mined land reclamation. For example, the European Union has conducted a review of existing European laws concerning mining wastes and mine water and is considering new directives concerning mine waste and mine water management and liability schemes that are likely to significantly impact mine closure and mined land reclamation. Many countries, particularly those outside of North America, Europe, and Australia, have recently adopted or are considering new mine closure and reclamation legislation and regulations. These include significant hard-rock mining countries such as Chile, Peru and South Africa. This paper identifies recent developments in hard-rock mine closure and mined land reclamation laws in the United States, focusing on several of the more significant and controversial developments. It also discusses some of the more significant international efforts to consider mine closure and mined land reclamation laws and policies and some of the notable conclusions and trends from those efforts. The focal issues discussed in this paper include requirements for the reclamation of open pit mines, including backfilling; consideration of and measures to address the mining of sulfide ores and potential for acid mine drainage; and new requirements for the estimation of closure and reclamation costs and for financial assurance for closure and reclamation.

Jan 1, 2005

By M. R. Stokes

Over the recent years there has been an increase in the application of retreat mining on longwall faces as mine operators strive for ever greater productivity. The purpose of this paper in then to review current practice as a starting point and then move forward to discuss the future geometry's that a longwall face may take. Single and double production zone three roadway faces are assessed. All possible configurations of three roadway faces are defined. Unsuitable configurations are rejected after analysis of broad ventilation issues. The remaining configurations are then assessed on an operational basis, this includes: limits on retreat synchronisation, structure of centre gate, floor bulging and equipment installation. The remaining viable configurations are then further assessed on ventilation issues, this includes: provision for gas control/gas fringe, face climate and balancing of face flows. Possible face climate is assessed using numerical simulation of the various configurations, the predicted dry/wet bulb temperature and predicted levels of heat stress indices are given and discussed in detail, along with face flow balancing. The necessary conditions required for the successful operation of a double production zone three roadway face system are formulated, together with conclusions as to the possible level of application.

Jan 1, 1997

By Rudolf E. Greuer, Xintan Chang

Mine fires have always been of great concern to mining engineers and their behavior has been studied for a long time. Although an abundance of observations exist, no satisfactory mathematical model for their interpretation and extrapolation has become known. The paper presented here tries to close this gap, making use of the laws of chemical kinetics, energy and momentum conservation. To overcome the mathematical difficulties, the fire zone is axially divided into segments and radially into sections, each one with an extension of only a few inches. Conditions in segments and sections are updated in time intervals of one second or less. To solve the large number of resulting equations, a numerical solution is performed. The model has so far been tried on timber fires. It confirms experimental observations on the ignition phases and equilibria of these fires.

Jan 1, 1987

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, A. E. Clark, R. P. Bush, L. E. Schultze

The U.S. Bureau of Mines conducted copper exchange capacity (CuEC) tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the CuEC as a function of Cu concentration, pH, and temperature. Further testing resulted in regression equations expressing CuEC's of Na and Ca montmorillonites and attapulgite as a function of Cu concentration, pH, and the concentration of metal ions which compete with Cu for exchange sites. Using these equations, an analysis was made of the impact each clay could have on overall copper recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of copper from in situ leaching solutions. Copper losses are decreased by the presence of competing ions, and A1 and Mg have the largest impact of those ions normally present in Cu leaching solutions.

Jan 1, 1993

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine's strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

By Gerhard Mücke

Geothermal and operational reasons in the German coal mining industry make it necessary to an increasing extent to climatize coal faces and headings by means of refrigeration plants. Air coolers installed on coal faces as well as in gateroads play an important part in such climatization. They must transfer, under difficult conditions, the refrigerating capacity supplied by central or de-central refrigeration plants from the chilled water to the air in the workings. The performance data of two new types of coalface coolers and of two different types of gateroad coolers were measured in two testing stations under different thermo- dynamic conditions with dust-free fresh air. As air coolers must be installed particularly at working points with a high .dust load the heat exchanging surfaces are fouled for the most part causing an essential reduction of the refrigerating capacity. The investigations therefore were extended to measurements with a certain dust load in the intake air of the coolers.

Jan 1, 1980

By Natarajan K. A.

During sulphide ore grinding, electrochemical interactions between grinding medium and the minerals play a significant role in bringing out enhanced ball wear on the one hand and alter the surface property of the ground minerals on the other. The role of the flotation reagents added simultaneously during grinding with respect to ball wear as well as flotation is yet to be established. Electrochemical measurements such as rest potential, combination potential and galvanic current between sulphide mineral and ball material couples have been carried out in the presence and absence of flotation reagents to understand the nature of electrochemical interactions between ball material and sulphide mineral. Electrochemical mechanisms and models have been proposed to explain the role played by the flotation reagents during different binary, ternary and quaternary interactions with respect to ball wear during grinding.

Jan 1, 1992

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986

By Cathleen J. Webb, Arden D. Davis

Begun in 1992, an abandoned and inactive mine inventory in the Black Hills National Forest has resulted in a hazard ranking of the most severely affected sites. For purposes of the inventory, the Black Hills were divided into three main regions: the northern Black Hills, with primarily gold mines; the central Black Hills, with pegmatite mines and some gold mines; and the southern Black Hills, with primarily uranium mines. A computerized data base has been developed along with standard forms for field crews. The forms were designed to provide maximum compatibility with other abandoned mine inventories on various federal and state lands. Measures recommended for the most hazardous and heavily affected sites include regrading of unstable slopes, fencing of open shafts, and remediation of the most severe acidic mine drainage problems. Specific examples are illustrated where remediation and safety measures were recommended or have been implemented. The vast majority of the sites, however, needed little or no remedial action.

Jan 1, 1995

By W. G. Pariseau

Recent advances in rock-mass mechanics and computational technology now allow for the stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time dependent. In addition to water pressure and flow in jointed, possibly porous, rock masses, all of the usual dry-mine parameters, including the premining stress state and rock-mass properties, are taken into account. Finite-element analyses of shafts and tunnels, as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass, indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor or, equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and the minimum safety factor at the wall in the wet case is always less than the dry case, regardless of drainage time allowed.

Jan 1, 1997

By C. B. Manula

A method for the feasibility assessment of open-pit operations using conventional shovel/ truck systems to mine steeply pitched coal seams has been applied at The Pennsylvania State University. Three computer models were developed for the analysis: a geology and reserves model (GEOL), an open-pit materials handling simulator (OPMHS), and a cash flow model (CASH) (Manula, Albert, and Burgos, 1976). GEOL provides the basic mining data; OPMHS simulates shovel/truck performance related to pit profiles and average mining locations to provide productivity rates needed to size the system; and CASH provides either a selling price or rate of return (ROR) for the product. The general flow of information generated by these models is shown in Fig. 1. Since the ratio of overburden-extracted to coal-produced places a definite economic limit upon a mining venture, geological data must be analyzed with the least possible manual effort to minimize computational errors. This is especially true if the property contains several seams that are steeply pitched. In this situation, a computerized analysis is by far the most efficient and effective method to determine coal reserves and waste tonnage. This chapter describes the reserve model developed at Penn State and provides an example to demonstrate its application.

Jan 1, 1979

By Donald E. Ranta

Many portions of the mining industry are under intense pressure to reduce costs while commodity prices languish. In response, global Internet-based marketplaces to deliver business-to-business (B2B) e-commerce solutions are being established to reduce costs and improve efficiencies across the mining industry supply chain as well as with customers. Over time these marketplaces will likely evolve to create an integrated supply chain solution, layer in value-added services, and develop mining community portals with industry content. Significant opportunities to help reduce costs and create value are available in mining e-procurement as well as in on-line product sales. The supply chain for the industry is highly fragmented and many mining companies have numerous inefficiencies in procurement. An e-procurement marketplace (or "exchange") can immediately address these inefficiencies and offer numerous benefits to buyers and suppliers. These benefits include improved sourcing options, inventory cost reduction, transaction cost reduction, access to value-added services, lower customer and supplier acquisition costs, improved reach, and improved information flows.

Jan 1, 2001

By Allan D. Fernie

Many long conveyors, 2 - 20 km plus, have been installed over the past 10 years. Conveyor belt life, depending on the conveyor length and material handled, will generally range from 10 - 15 years. To replace long conveyors splicing one or two rolls into a conveyor run on an intermittent basis can be prolonged in an operating system involving considerable downtime and scheduling problems. This paper presents some of the methods used to- date and highlights forward planning for such an event. Special belt handling equipment required and the execution of a belt change operation are described in detail. Wright Engineers Limited have worked in collaboration with Canada Conveyor to design and implement the methods described herein.

Jan 1, 1993

By W. Morgan, D. Gove

In truck and shovel operations, productivity and cost per ton are influenced by the system matching choice, Optimization involves a balance of the size and number of trucks, the size and type of loading tool and the projected material conditions and haul roads. Caterpillar has updated its Fleet Production and Cost program so miners can more easily look at matching choices and optimize on the variable they choose. This paper introduces the Fleet Production and Cost program. It then demonstrates its capabilities with examples of optimization. Mining operations that use trucks need to properly match the number and size of hauling units (trucks, wagons, scrapers, etc.) to a loading unit (wheel-loader, hydraulic shovel-excavator, cable shovel, push tractor, etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length, grade or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool that can be used to optimize the truck-loader match.

Jan 1, 1995

By Krzysztof Filek, Anindya Sinha, Bernard Nowak

Taking into account the possibilities of condensation of water vapour contained in air during its flow through a series of spot coolers as well as formation of eventual fog, a mathematical model of dynamic temperature, specific humidity and degree of fogging of cooled air in underground mining galleries with direct ventilation is developed. In the gallery, there situated various heat and moisture sources both of distributive and of concentrated types. The model is represented by three partial differential equations of first order. The cases of cooling with full as well as with partial air stream flowing through the gallery are distinguished. Owing to the fact that in practical designing, more important is the knowledge of the variation process of temperature, specific humidity and fogging of cooled mine air at steady state conditions, the model is modified to a set of three nonlinear ordinary differential equations. Based on the presented algorithm, the obtained set of ordinary differential equations is numerically solved which enables to: • specify the distribution of temperature, specific humidity, relative humidity and degree of fogging of cooled air in mining galleries; • determine the cooling powers of air coolers for their known locations; • indicate the locations of the coolers of known cooling powers. Exemplary calculations of temperature and relative humidity of cooled air are presented graphically in a number of diagrams.

Jan 1, 1997

By Bryan C. Smith, Duane R. Skidmore

Volumetric mass transfer coefficients and gas holdups were measured in a concentric tube airlift reactor designed for the microbial desulfurization of coal. The slurries were comprised of an acidified basal salts solution containing thirteen different weight percents of coal (74 µm Ohio #1) at three temperatures. An enhancement in the mass transfer coefficient, KLa, with respect to that measured in pure solution was found at weight percents of 5 (volume fraction solids, ES = 0.035) or less, the greatest enhancement being as great as 37% at approximately 2 weight percent (ES = J 0.014). At higher solids fractions, the mass transfer coefficient decreased with further solids additions, decreasing by as much as 91% at 40 weight percent coal (ES = 0.315). KLa increased with temperature at all solids concentrations, the greatest increase being 392% at 72°C vs that measured at 30°C. Gas holdup, EG decreased with all increases in solids loading by as much as 65% and increased by as much as 67% with temperature. KLa and EG were correlated with operating conditions separately, and the separate correlations combined to yield overall correlations for the mass transfer coefficient and for the gas holdup. The correlations are suitable for inclusion in system models devised earlier for microbial coal desulfurization processes, and may be used for design, operation and cost estimation for such systems.

Jan 1, 1989

By Kumara S. Rachamalla

Mineral activity in Ontario represents an annual production in excess of $4 billion. The Ontario government encourages the mining industry to undertake mineral development through grant programs and incentives offered by mineral resource taxation. Computers are playing an increasingly important role in improving productivity in the administration of incentive programs and the Mining Tax Act in Ontario. This has meant speedier processing of grant applications and tax returns which is resulting in a streamlined approach to incentives and taxation in Ontario. The use of computers has resulted in significant contributions to key areas of concern such as assessment of mining tax returns, analysis of the changes, if any, to the Mining Tax Act and modeling of the Ontario Mineral Exploration Program (OMEP). Implementation of state-of-the-art technology such as Local Area Networks (LAN's), fourth generation languages and integrated micro-mainframe information processing has resulted in improved productivity as well as lower costs. As a result, the respective services provided to the mineral industry by these two programs are now delivered in an efficient and cost-effective manner utilizing the latest available computer technology.

Jan 1, 1986