Search Documents

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By M. B. Haggerty, R. J. Sheets, F. Abbasy

To address coal refuse tailings storage needs for a mine operation in western Canada, a feasible solution was to convert excavated open pits into tailings cells. A slope stability investigation and design study were completed to determine the necessary width and slope geometry for in-situ native plugs as the impoundment embankment. The native plugs separate the previous open pit from the current active open pit. This configuration allows for the deposition of refuse tailings in the previous pit while allowing mining to safely continue “downstream” of the temporary impoundment. As mining progresses, each subsequent pit will be filled with refuse tailings; thereby, buttressing the upstream slope of the previous native plug. Although these cells are excavated, and the timeframe for downstream exposure is relatively limited, the native plugs are classified as dams and must be designed to meet applicable safety of dam standards since they impound water and tails above mining personnel in the subsequent open pit. The presentation and paper will discuss the investigation and analysis conducted to develop the geotechnical and hydrogeological design recommendations.

Mar 2, 2022

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

By Yong Pan, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate gas dilution situation when the source is located in the extraction drifts.

May 12, 2022

By JA Vallejos

High stress underground mining poses a significant challenge to rock mechanics and rock engineering. To overcome theses challenges significative improvements in solutions and best practices of the design and operation of mines under high stress have been developed and implemented. This paper presents certain topics related to the management of high stress for sustainable underground mining. The topics include; the effect of preconditioning techniques (destress blasting and hydraulic fracturing) in the seismic rock mass response to underground mining and the dynamic behaviour of rock support systems. The opportunities associated with research in rock mechanics and practical rock engineering are discussed.

Apr 26, 2022

By Roland W. Merwin

The Bureau of Mines has studied the possibility of using the heap leaching process for treating the gold ores in the sedimentary beds of northeastern Nevada. This paper summarizes all available information on the technical and economic feasibility of heap leaching oxidized ores from these beds, past industry application of vat leaching, results of recent Bureau of Mines and industry tests on heap leaching ores from this region, and requirements for planning the proper application of heap leaching. Preliminary tests on representative samples of ores from the region show that a satisfactory recovery of gold can be obtained by heap leaching the ores with cyanide at a relatively coarse size. Significant deposits of gold ore occur in sedimentary beds of various locations over an extended area 40 miles wide and 200 miles long in northeastern Nevada. The area is centered 40 miles west of and runs parallel to the leading edge of the Roberts Mountain thrust fault system, a prominent geologic feature in the area. The general locations of past and present gold mining operations are shown in figure 1. (slide 1)

Jan 1, 1969

By Robert F. Kehrman

As part of the Bureau of Mines research on the In-Situ Uranium Leaching, various geophysical resistivity measuring techniques were -evaluated to identify a rapid reliable method for detecting the underground migration of lixiviant outside of the planned limits. Surface and downhole galvanic resistivity and controlled source audio-magnetotelluric (AMT) methods were tested at an in-situ uranium mine in Northern Wyoming during start-up of a new mining area. Downhole galvanic and AMT were the most promising techniques.

Jan 1, 1980

"Twin Creeks is a gold mining complex that is part of Newmont’s Nevada operations. The mining complex is composed of two openpits, Mega and Vista, external ore sources and a set of existing stockpiles, all of which provide ore for an autoclave, an oxide mill and a heap leach. Mega pit provides sulfide ore for the autoclave, whereas Vista pit provides oxide ore for the oxide mill and the heap leach. Both pits operate the same mining equipment and their extraction sequence must, therefore, be optimized simultaneously. Stringent blending requirements are associated with the operation of the autoclave for the sulfide ore. Strategic blending optimization on a large scale has brought significant value to the operation by increasing synergies. This paper presents the implementation of a stochastic optimization framework for the long-term production planning at Twin Creeks that simultaneously optimizes mining, stockpiling, blending and processing decision variables. The uncertainty and variability associated with the different sources of material are incorporated in the optimization model by means of stochastic simulations. The stochastic solution generated shows substantial benefits by increasing forecasted recoverable gold, leading to increased cash flows, while reducing the risk of not achieving forecasts by increasing the probabilities of meeting production and blending targets.IntroductionMine operations consist of multiple components such as mineral deposits, stockpiles, external sources, mills and autoclaves. These components represent a mineral value chain, also known in the literature as a mining complex (Montiel and Dimitrakopoulos 2015; Goodfellow and Dimitrakopoulos 2016). The material extracted from the mines flows through the different components and is transformed into sellable products. This flow of material in a mineral value chain involves complex, nonlinear transformations that render the use of industry-standard optimizers difficult. Furthermore, the optimization of a mining complex can be formulated as a mixed-integer, nonlinear optimization program with millions of integer variables representing mining, blending, stockpiling and processing decisions, prohibiting the use of conventional nonlinear optimization approaches. Previous methods that consider the joint optimization of multiple components of the mineral value chain are available (Hoerger, Seymour and Hoffman, 1999; Chanda, 2005; Stone et al., 2005; Wooller, 2005; Whittle, 2007, 2010; Bodon et al., 2010). Although these methods add value by increasing the synergy between the different components of the mining complex, they rely on simplifying assumptions that constrain their efficacy, while ignoring a most critical aspect. The latter aspect includes the geological uncertainty and actual variability of the materials in the mineral deposits mined and are supplied to the related mineral value chain, similarly to conventional life-of-mine planning methods used for individual mines (Dimitrakopoulos, Farrelly and Godoy, 2002; Godoy and Dimitrakopoulos, 2011; Spleit and Dimitrakopoulos, 2017). Additional simplifying assumptions may include: the consideration of a limited number of components, the combination of different methods, the aggregation of variables, fixed production schedules the definition of policies prior to optimization, such as cutoff- grade definition or destination of mining blocks, the linearization of nonlinear transformation functions and/or the disregard for the uncertainty of several critical parameters (Whittle, 2007). The simultaneous optimization of multiple components of a mining complex was introduced by Newmont. Hoerger, Seymour and Hoffman (1999) implemented a mixed-integer programming formulation to optimize Newmont’s Nevada operations. The model is based on the work of Urbaez and Dagdelen (1999) and simultaneously optimizes the extraction of materials from multiple deposits and the delivery of ore to multiple plants, as well as as"

Dec 1, 2018

By Remi Tremblay

This paper describes the laboratory study which permitted an exploration of high grinding ball consumption in the secondary open circuit wet grinding mills at the Sidbec-Normines plant, Port Cartier, Québec. Corrosion undoubtedly exists but is of minor importance. Abrasion resulting from the physical nature of the company's iron concentrate is the main reason for the high ball wear. It was found that at least 30% reduction in ball consumption is possible by decreasing attrition grinding through the use of lifters in the mill. At the industrial level this would entail more lifters and/or higher lifters in the mill linings.

Jan 1, 1984

By A. R. Negele

Kaolin-based pigments are the most widely used pigments in the paper industry. Several types are available and include standard hydrous, delaminated, calcined, chemically-structured, and most recently, composite pigments. Within each category, a spectrum of products is available to satisfy the application requirements of paper producers. The paper industry has a broad range of applications including fillers in woodfree and groundwood-containing papers, pigmented size press applications, ultra-lightweight and lightweight coated papers, coated merchant papers, cast coated papers and coated paperboard. Each application has its own set of performance criteria and suppliers must work with mills to identify appropriate product(s) to fulfill these requirements.

Jan 1, 1993

By C. M. Brinckerhoff

Much has been written in the mining technical magazines about the caving system. Many of these articles were published in the Transactions of the American Institute of Mining Engineers prior to World War II. In recent years little has been written on mining methods or on the detailed planning always required. Block caving had primarily been used to mine deep copper ores in Africa, the United States and in Chile, although other ores had been mined by this same system. Asbestos ore had been caved in Canada, tin ore in Bolivia, molybdenum ore in Colorado, iron ore in Wyoming and Sweden, and limestone in California.

Jan 1, 1984

By B. N. Conley, K. D. Luxbacher

"The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. The explosions that occurred at the Sago Mine in 2006, the Darby Mine in 2006, and the Upper Big Branch Mine in 2010 have caused a ripple in an otherwise steadily improving safety record. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reached a level of diminishing returns. Risk management, a safety approach that has been successfully applied in various industries including mining across the world, may provide a means to surpass the safety plateau in the U.S. RISKGATE is an Australian risk management program for mines that shows great potential for application in the U.S. However, fundamental differences between the coal mining industries in Australia and in the U.S. prevent direct implementation. This paper discusses aspects of the RISKGATE body of knowledge that require some adaptation before this program may be applied to the U.S. mining industry. INTRODUCTION The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reach a level of diminishing returns. In order to combat this stagnation in performance, a modification to the manner in which the mining industry approaches worker safety may be warranted. The implementation of a risk management based approach presents a potential method for not only surmounting the current safety plateau but also for achieving the long desired objective of zero harm. RISKGATE a risk management body of knowledge designed for the Australian mining industry that shows great potential for application in the U.S. This paper discusses aspects of the RISKGATE body of knowledge that require adaptation before implementation in the U.S. mining industry. These adaptations are based on differences in operating practices and governmental regulations. This discussion will focus on the three major U.S. risk areas of explosion prevention, ground control, and moving equipment."

Jan 1, 2015

By D. Diggins

Experimental apparatus for the determination of powder wettability is described. The principle of the technique is based on the measurement of the equilibrium capillary pressure in a packed bed of particles. Both the macroscopic solid-solution-vapour contact angle, e, and the specific surface area, A(m2g-1), of the powder, can be obtained. Experiments on angular quartz particles have been performed. A wide range of situations have been covered: hydrophobic and hydrophobic particles wetted with water, a variety of organic liquids and solutions of surfactants. The results show that reliable and reproducible values for 0 and A for angular and relatively coarse powders can be obtained with the proposed equipment for advancing liquid fronts in the absence of soluble surfactants. In the latter case and for receding liquid fronts in general, only qualitative trends have been obtained.

Jan 1, 1992

By C. K. C. K. Gupta

The rare earths in elemental form are required for a variety of scientific and technological purposes. They are not easily obtained in this form, due to the great chemical stability of the rare-earth compounds and the strong tendency of elemental metals to react with everything they come in to contact with, especially at high temperatures. Beginning in the 1950s, when sufficient quantities of separated rare earths became available, as the result of intense research and development, three processing routes were developed to accomplish the preparation of all 16 naturally occurring rare-earth elements. They are chemical reduction of the halide intermediates, the oxides and electrochemical reduction of chlorides and oxide-fluoride mixtures. Not all the processes are effective with all the rare earths. In spite of the celebrated similarity of trivalent rare earths, the physical properties of individual rare-earth elements are sufficiently different that a variety of techniques are required for their preparation. The development of reduction processes for the rare-earth metals are covered in this paper, with focus on the oxide reduction routes. The strong reliance of effective reduction processes on the fundamental science of reduction reactions is highlighted.

By Allan M. Johnson

Dewatering is a major operational cost at sane mines. Under certain conditions, costs associated with water disposal may continue beyond the productive life of the mine. For mines with mineralized waters, this is of special concern. Since 1974 experience has been gained from the examination of a number of closed underground metal mines that exhibited drainage problems. It was observed in certain cases, that had appropriate steps been taken prior to closure, that the resulting drainage problems could have been largely avoided. The pre-closure steps would have involved alteration to the "plumbing system" of the mines: i.e., the drifts and crosscuts interconnecting the workings of the mine. This could have best been accomplished by the placement of bulkheads and/or selective drifting. In addition to reconfirming that hindsight is 20-20, a lesson learned from these case studies shows that a relatively simple hydrologic evaluation prior to mine closure may avoid a troublesome and costly drainage problem.

Jan 1, 1983

By J. R. Tonry

In the grinding of dry non-metallic materials such as rocks, ores, gypsum, lime, and cement clinker, it is recognized that only a relatively small portion of the energy is utilized for actual size reduction, and the major portion of the energy used is converted into heat. As a result, heat is generated inside grinding mills imparting to the ground product a higher temperature than that of the mill feed. In some cases, as for instance in grinding cement clinker and gypsum into finished cement, it may be desirable to keep this temperature increase within certain limits, to avoid any change in the properties of the product and, because consumers may specify a maximum temperature of the finished product for reasons associated, with the tulimate use of the cement. The actual proportions of heat and useful work are somewhat indefinite. Some tests have indicated that nearly all the energy is converted into heat, and. other investigators have found that they could account for "everything except the noise." Investigations sponsored by the American Institute of Mining and Metallurgical Engineers, and carried out with an adiabatic calorimeter, indicated that a surprisingly high 19 percent of the energy might actually be used for size reduc¬tion. However, for the purpose of the following discussion it will be assumed that: (Fig. 1) 10% is lost in motor and gears 10% is lost by radiation and convection from the mill body 10% is used for size reduction, and. that 70% of the energy input leaves the mill as heat in the ground. product. A typical example (Fig. 2) would be a 7x22-ft tube mill operating in open circuit, driven by a 400 hp motor, charged with 77,000 lb of grinding media and producing 70 bbl or 26,300 lb of cement per hour. Reducing this cement from a clinker size of 96 percent passing a No. 16 mesh sieve to a specific surface of 3,230 sq cm per gm (Blaine) will increase the temperature of the cement approximately 143F above the temperature of the feed, as explained later. If the tempera¬ture of the clinker therefore is 125F, the finished cement will be 268F, which in some cases may be too hot. : When cement temperatures approach a range during grinding where dehydration of the gypsum becomes a problem, a logical consideration would be some means of reducing the temperature before it attains the range conducive to gypsum dehydration. Regardless of the varying degrees of heat generated within the mill or mills during grindingto various finenesses, consideration of the maximum safe limit for any type of cement being ground, which may vary fromplant to plant, govern in refining the mill circuit to obtain a safe temperature range. All plants are not necessarily required to do the same cooling job, and may or may not use cement coolers following the grinding circuit. (Not discussed in this paper). In the past, various means have been employed for controlling this temperature increase, Such means have included water cooling of the outside of the mill shell; equipping the shell with cooling fins; injection of moisture inside the mill; ventilation through the mill; and., in cases of closed-circuit grinding, drawing cooling air through the classifier; the purpose in all such cases being to remove heat from the grinding system.

Jan 1, 1958

By Takahide Wakamatsu

In Japan all the complex sulfide ore deposits of base metals have been developed as underground mining. The underground mining cost is extremely high as compared with open pit mining case. Therefore, in milling section of base metal mines, technical advance for maximum recoveries of valuable constitutents in ore has been required all the time to utilize as much ore mined as possible. At present, in mill plants treating "Kuroko", complex sulfide ore, concentrates of copper, lead, zinc, pyrite and barite are produced, with gold and silver contents in the copper, lead, and zinc concentrates being estimated as extra profit. As in the case of Kuroko milling plants, gold and silver contents in the lead and zinc concentrates of lead-zinc ore milling plants are also varuable from an economical viewpoint. Silver content is very high in Kuroko crude ore as well as lead-zinc ore.

Jan 1, 1982

By George H. Davis

The Caribou sulfide deposit near Bathurst, New Brunswick (Figure 1) is illustrative of one variety of strata-bound sulfide deposits. It consists of numerous near-vertical sulfide lenses which are concordant to the foliation and lithologic layering of low-grade metamorphic host rocks. Pyrite is the chief mineral in these lenses, but appreciable quantities of sphalerite, chalcopyrite, and galena are also present. Rocks in the Caribou mine area belong to the Tetagouche Group of Ordovician age. They consist chiefly of (1) quartz-sericite and quartz- sericite- feldspar schists, (2) greenschists, and (3) slate and phyllite. The trends of these steeply dipping rocks define the trace of a tight, steeply plunging fold structure, the Caribou fold (Figure 2). This fold plunges approximately 750 to the north-northwest; its axial plane strikes N.20°E. and dips steeply westward. Sulfide lenses of the Caribou deposit are associated spatially with the Caribou fold. The deposit is located in the fold along the contact between quartz-sericite and quartz-sericite-feldspar schists on the hanging wall and quartz-chlorite-sericite phyllites and graphitic schist on the footwall (Figure 3). Genesis of the Caribou deposit is ambiguous because its strata-bound form suggests syngenetic sulfide deposition, whereas its location within a fold suggests structurally controlled epigenetic mineralization. Acceptability of a particular genetic model rests on establishing the time of mineralization relative to deposition, deformation, and metamorphism of the associated rocks. To establish the timing for Caribou mineralization, the deformational histories of rock and sulfide, respectively, were compared. Epigenetic and syngenetic models can be tested against this interpreted structural history of the Caribou deposit.

Jan 1, 1971

By P. Guliov

In the first part of this paper the authors present an overview of industrial minerals produced in the Canadian provinces of British Columbia, Alberta and Saskatchewan, and supplied to the Pacific Rim countries. The second part outlines some of the unique opportunities for industrial minerals that exist in the three western Canadian provinces and those minerals we feel have development potential for overseas markets. Because of time constraints, it is not an exhaustive presentation on industrial minerals, but is focused on a few selected minerals that we believe have high potential.

Jan 1, 1990

By David D. Eyer

In today's world coal market, coal quality is becoming increasingly important. Often the coal quality parameters are one of the crucial considerations in the development of a coal mine. Because of the user's tighter specifications and because of strict environmental regulations, coal producers are being called on to predict with increasing accuracy, not only the quality of their product but also the variability of that quality. This area of reserve evaluation is naturally receiving a great deal of scrutiny. Consolidation Coal Company has developed reliable and sophisticated methods for predicting coal quality, but the company's efforts continue to search for even better techniques. The following is a step-wise summary of The methods currently used by consolidation coal company, with A recent project used as an example. Two of the newer, and as yet experimental techniques will be briefly discussed.

Jan 1, 1980