Search Documents

By R. K. Mehta

An accurate, efficient and stable computation of the mill matrix function (eAt) is needed where mill matrix (A) is a real general matrix. Two important modeling cases in comminution where such need arises are: Heterogeneous comminution behavior of multi-component ores and ultra-fine grinding involving simultaneous attrition and fragmentation breakages. This paper presents the application of a novel splitting method in conjunction With similarity transformation technique in the form of "product formula" which is found to work in all cases and uses a most aggravating, yet interesting property of the matrix exponential in a restricted sense. Results are presented showing that this method can yield solution as accurate as those obtained With an analytical technique. The utility of this computational approach is demonstrated by parameter estimation analysis using a distributed component model in the liberation area through computer simulations.

Jan 1, 1992

By S. J. Swan

A computerized on-line process control system designed to monitor and control the seven-cone copper precipitation operations at Kennecott Copper Corporation's Chino Mines Division in New Mexico has been continuously operating since April, 1972. The cone monitoring system consists of plant sampling components, process measurement instrumentation, on-stream X-ray spectrometer, control computer, typewriters for programming and for operating reports, foreman's communication console, and cone automation hardware. The system provides the following functions: (1) assays for copper and iron from ten process streams on a continuous rotating basis, (2) directs hardware to automatically flush and start up cone units based on measured performance variables, (3) provides continuous plant operating data and calculates metallurgical averages as well as production figures for shift and daily summaries, and (4) provides data logging capabilities. The system is very reliable and improves plant performance by increasing yields, reducing scrap iron consumption, and reducing operating manpower requirements.

Jan 1, 1975

By P. Schumacher, M. Fein

"INTRODUCTION Newmont’s Twin Creeks operation, part of its Nevada operations, produces gold from two large open pit mines. Mined ore is processed at one of three on-site facilities: a refractory mill with two autoclaves, an oxide mill and heap leaching facilities. Twin Creeks also processes various off-site sourced concentrates and ore including high grade underground ore from the Turquoise Ridge joint venture with Barrick Gold Corporation. This paper discusses Twin Creeks’ strategic mine planning process which is part of an in-depth continuous improvement program called “Full Potential.” The process involves cost analysis, phase design validations, life-of-mine production scheduling optimization, mill blending strategy and stockpile management. Through this Full Potential strategic planning, Twin Creeks is creating significant value by increasing near term free cash flow and life of mine net present value (“NPV”) and achieving cost reductions. TWIN CREEKS OPERATION Twin Creeks is one of the major gold producers in Newmont’s Nevada operations (see Figure 1, 2 and 3). Located approximately 15 miles north of Golconda, Twin Creeks produced approximately 28 % of the Nevada operation’s 2013 gold production of 1.8 million ounces (Newmont 2014). The production included Turquoise Ridge sourced gold ore from the joint venture (75% Barrick Gold Corporation, 25% Newmont).At Twin Creeks, there are two large open pits, named Mega Pit and Vista Pit (see Figure 4, 5 and 6). There are 3 to 5 phases in Mega Pit and 2 to 5 phases in Vista Pit depending on the gold price assumption. There is also an underground exploration project at the bottom of the Vista Pit. Twin Creeks produces gold from a variety of ore types requiring different processing techniques depending on economic and metallurgical characteristics. To ensure the best use of processing assets, engineering and processing groups at Twin Creeks utilize a Mixed Integer Linear Programming (“MILP”) model to guide the flow of mine sequences and material routing to various process facilities (Kawahata, Schumacher and Hufford 2013)."

Jan 1, 2015

By M. Guzman, M. Romero, S. Bravo-Thais, M. Flores

The phytoremediation method is proposed to recover valuable metals from polluted soils. In this sense, the objective of this research is to determine if it is possible to use native plants in the recovery of precious metals from abandoned mining liabilities. The tailings samples containing Au and Ag were acquired from the northern region of Peru. Two native plant species, Stipa Ichu and Cortaderia Nitida, were used. Results show that Au was recovery around 19% (1.52 mg/Kg) and 25.43% (1.78 mg/Kg) by using Stipa Ichu and Cortadeira Nitida, respectively. Besides, Ag had a better recovery in the Stipa Ichu reaching a value of 6.83% (0.628 mg/Kg); in contrast, Cortadeira Nitida had an efficiency of 3.6% (0.814 mg/Kg). Bioaccumulation, bioconcentration and translocation factors were calculated by determining the concentration of precious metals in the roots and aerial parts of each plant. Results show that Stipa Ichu had a greater capacity of hyperaccumulated Ag compared to Au; while Cortaderia Nitida tended to have a better performance for Au. In conclusion, both plants are recommended for phytoremediation of mining liabilities.

Feb 1, 2023

By Richard F. Roethe

Surface coal mining productivity in the U.S. and Illinois has shown a general declining trend since 1969. The U.S. Department of Energy conducted an analysis in 1980 of the causes of declining productivity in different states. This paper presents a detailed analysis of changes in overall productivity and productivity in different functions such as overburden preparation, overburden stripping, reclamation, coal handling, etc. during the period 1970-1982. Statistical analysys techniques including multiple regression were utilized in the study.

Jan 1, 1983

By Raphael G. Kazmann

Water occupies a dual role in our industrial society. It is the indispensable raw material, essential to life itself. It is equally an industrial nuisance, interfering with the production of industrial minerals, making construction difficult, flooding valuable land, and generally producing problems because it is in the wrong place at the critical time. The legal position of water as a nuisance, and the counter measures to be taken, have been well established procedures for determining the responsibility for damage caused by water, and the organization of drainage districts and flood control and levee districts have been legally tested many times. Thus there is rather adequate legal doctrine concerning water, the common enemy. But recently efforts have been made to regularize the position of water as a useful, industrial, commodity. Such laws are not new to the West, where the doctrine of appropriation for beneficial use is slowly becoming the water law. Elsewhere the University of Michigan has produced a "model" water law and efforts are being made to induce all of the states to use this law, or a slight variation of it, as the basis for legislation. There are many serious criticisms of the proposed "model"-law, and the writer strongly opposes many of the provisions. But the fact remains that water is, in itself, so useful and essential that laws have been, and will be, passed to insure the orderly development of our water resources and to prevent waste. The, most important aspect of these "water-use" laws is that, wise or unwise, the existing laws and the proposed laws have been "water oriented". "Water oriented" means that it has been tacitly assumed that the beneficial use of water, either surface water or ground water, is the overriding consideration.

Jan 1, 1960

By Chi-shing Wang

The U.S. Bureau of Mines has been developing the mechanical roof pulling technique as a method for evaluating the effectiveness and the comparative advantages and disadvantages of various roof bolting systems, based on the characteristic responses of bolted nine roofs to a prescribed external loading system. Preliminary experiments were conducted in the Bureau's Safety Research Coal Mine using a 12-foot and a 16-foot-span test rig. The experiments have proved the capability of the test rigs and suggested the viability of the test method. This paper summarizes the test concept and the experimental results.

Jan 1, 1974

By J. M. Pugliese

The U.S. Bureau of Mines is developing designs and estimating costs for vertical in situ copper mining wells as part of its in situ mining research program. Conceptual designs and estimated costs for "deep" 1100 m (3600 ft) recovery and injection wells in an undisturbed copper ore zone are presented. Within a single in situ copper mining well, multiple perforated well completions and associated costs are discussed for two ore zones between depths of 370 m (1200 ft) and 550 m (1800 ft). The order of well specifications for designing these wells is explained.

Jan 1, 1995

By A. Bruynesteyn

The results of leaching experiments in columns simulating 80 and 200 ft deep cores through a leach dump are discussed, By equipping the columns with can precipitation plants, actual plant conditions could be duplicated. The results produced a better understanding of the physical and chemical limitations of the leaching process.

Jan 1, 1975

By Dennis F. Koschak

Production tests at Reserve Mining Company's iron ore pelletizing plant established that rubber-lined balling dm produce a green pellet equivalent in quality to those produced in conventional balling drums equipped with reciprocating cutter bars. The flexing action of the rubber liner prevents concentrate buildup in the drums, eliminating the need for a cutter bar. Advantages of the rubber-lined drum includes a reduction in maintenance and operating manpower, reduced bentonite consumption with less drum surging, reduced power consumption, and improved drum on time.

Jan 1, 1983

By Ronald T. Cosburn

The Province of Ontario covers an area of some 400 thousand square miles, however the subject I will be talking about today, the licencing of pits and quarries in southern Ontario, refers to about one quarter of this total area but contains better than 93% of the total population of the province or about 8 million people. Southern Ontario had and still has many inviting features to industry. The Great Lakes almost surround us, hydro power has been relatively inexpensive and abundant, but more in line with our topic today are the ample deposits of sand, gravel and limestone, all of which are used directly or indirectly throughout and are the mainstay of our construction industry. I say we are fortunate to have these non-renewable resources in abundance in close proximity to our industrial and metropolitan areas, but like so many of our resources we have taken them for granted for too long. What has happened in our case, as I am sure is common in many of your own similar situations, because of the recent, current popular trend by naturalists and environ- mentalists to preserve our natural heritage at the expense of all else, through parklands and indiscriminate zoning policies, these once abundant reserves have been tremendously eroded.

Jan 1, 1982

By Brig M. Moudgil

It was reported earlier that francolite and dolomite from the South Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved at a reconditioning pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1984

By A. D. Walters

Computer simulation models of preparation plant operations and cost analysis have been used to determine the profitability of individual coals. The model's input consists of raw coal size and washability analysis, operating cost data, and raw coal and clean costs. The model's output predicts yields, qualities, costs and profitability for an individual coal.

Jan 1, 1987

By E. J. Ostrowski

The history of ironmaking dates back to 4000 BC when an open forge was used to produce a sponge iron from a heap of ore and charcoal. Even at this early date, man recognized the need for a fuel and a reducing agent. As time passed, man developed new methods of producing iron; however, these developments were centered on the mechanical aspects, and as a result, a furnace evolved which is now known as a blast furnace. During this period of evolution,' man struggled with the only fuel he knew - charcoal. Some 5600 years passed before any attempt was made to use coal as a fuel for the blast furnace. The use of coal had its beginning in 1619 when Dud Dudley of England first attempted its use in the blast furnace; as a-fuel and as a reducing agent. Coal charged to the top of the blast furnace was not satisfactory. The volatile matter of the coal choked the flues, and also the poor, strength qualities would not support the weight of the ore. Breaking up of the coal compacted the stock column to an impervious mass. One hundred and sixteen. years later in 1735, Abraham Darby of England introduced coke as the fuel and reducing agent in the blast furnace. The acceptance of coke as a fuel for the blast furnace was not spontaneous. As late as 1870, one-half of the pig iron product of the United States was made with anthracite coal, 30 per cent with raw bituminous coal and coke, and 20 per cent with charcoal. However, by 1910, 96.2 per cent of the blast furnace product was made with coke, 2.4 per cent with anthracite and coke admixture, and 1.4 per cent with charcoal. Coke became the standard fuel in the blast furnace. As the art of ironmaking progressed, more pig iron was produced and more coke was consumed. Coke oven capacity was progressively increased. In 1910, there existed approximately 4,000 coke ovens; in 1960 there was approximately 15,000 ovens. This increase in coke oven capacity was necessary to feed the mammoth appetite of modern blast furnaces.

Jan 1, 1962

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By Adrian Brown

Floor heave can be a major problem in large open pit mines. Unrestrained floor heave can lead to flooding, equipment destruction, slope instability and subsidence. It is particularly troublesome in coal mines where the floor is frequently relatively flat, and is often underlain by major water Searing units. This paper examines methods of analysis used in computing floor stability, and sets out a simple rational method of evaluating the required level of water pressure control to maintain acceptable floor stability. The approach is illustrated by reference to the stability of the floor of the Morwell open cut lignite project in Southeast Australia, where this approach has been used successfully for over a decade.

Jan 1, 1982

By William F. Lawrence

Research performed by the West Virginia University Coal Research Bureau under the sponsorship of the U. S. Bureau of Mines has demonstrated that coal-ash can be converted into mineral wool insulation of a quality equal to commercial grade mineral wool. An unexpected benefit has been gained due to the discovery that the usual and costly fluxing agents employed when using conventional raw materials are not required when producing mineral wool from coal-ash. Because coal-ash sources are commonly located close to mineral wool marketing areas and because mineral wool is seldom shipped far as a result of its low weight and high volume, the use of coal-ash may offer the mineral wool producing industry profitable opportunities. Moreover, coal-ash produced from experimental limestone based air pollution control processes also yields high quality mineral wool which may aid in retarding corrosion of metals contacted by the wool. In addition, internal fluxing effects and possible sulfur oxide utilization could provide economic advantages to the use of these "modified" ashes.

Jan 1, 1969

By William C. McBee

A sulfur concrete technology has been developed by the U.S. Department of the Interior, Bureau of Mines, in which chemically modified sulfur is utilized with suitable mineral aggregates to produce construction materials which are resistant to corrosion by acids and salts. This report presents a summary of the basic technology and results of testing the materials under actual operating conditions in 50 corrosive environments in 40 commercial plants. After 4 years of testing, there was essentially no evidence of material degradation or loss of strength. Regular concrete materials were attacked and in some cases completely destroyed under the same conditions. Testing is continuing to establish ultimate longevity and durability of the sulfur concretes. The materials are finding widespread applications in metallurgical, chemical, and fertilizer processing plants.

Jan 1, 1983

By W. V. Swarzenski

In its, effort to combat waterlogging and coil salinity, the later and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling and water sampling, since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline ground-water-zones in the Punjab Plain. Fresh ground water containing generally, less than 500 ppm (parts per million) of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh ground water extends to depths of 1,500 feet and more. Saline ground water occurs downgradient from sources of recharge, particularly in the lower central parts of the interfluvial areas and, presumably, underlies most of the Punjab Plain. The ground waters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters, near sources of recharge, to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in Dera Ismail Khan District sodium sulfate waters predominate. The pattern of distribution of saline ground-water zones and the observed gradual increase in mineral content, downgradient from sources of recharge, can be explained best by a hypothesis stressing the processes of evaporation from the water table and solution of minerals within the alluvial aquifer.

Jan 1, 1967

By Stewart W. Daniel

Competitive pressures involving product duality, uniformity and economics are increasing the interest in and accelerating' the adoption of automation by the cement industry. The demands of this industry on instrumentation and control manufacturers for more effective and reliable control of process variables is also increasing. The trend to replacing small grinding mills with a fewer number of larger mills is lowering the investment requirement per unit of capacity both for the mills and for their automation. Cement process control systems of today are more sophisticated than the equipment installed two or three years ago, not because the process itself is more complex but because todays demands require a higher degree of control action and accuracy. Because of increasing labor costs, an important objective of an automation program is a reduction in the process labor content. This can be realized by allowing the operator free time for other duties, by increasing the number of grinding circuits one operator can supervise and by removing to. a large extent the need for the operator to make process' adjustment decisions.

Jan 1, 1965