Search Documents

By John F. Papp

Chromite is used both as a metallic and nonmetallic mineral. Chromite ore is used as the source of chromium by the metals industry and is used, without chemical alteration, in the refractory and foundry industries. Chromite ore is also the source of chromium for the chemical industry. On average worldwide far more chromite ore is used by the metallurgical industry than by any other industry. Thus, although the primary purpose of this chapter is to describe the nonmetallic uses of chromite, the metallurgical uses must also be discussed in order to provide a complete description of this commodity.

Jan 1, 1994

By Frank H. Madison

The percentage depletion deduction on Federal Income Tax Returns under the provisions of the 1939 Internal Revenue Code and of Sections 611 to Section 615, inclusive, of the revenue act of 1954, have created innumerable administrative difficulties, and a new interpretation of "gross income from the property" in that the Courts have expanded the ideas of what constitutes "gross income from the property" to a degree unheard of and unthought of prior to the enactment of these two codes. Originally, under the Revenue Acts of 1917, 1918, and 1920 depletion was allowable, based upon mine valuations as of March 1, 1913; if the mine was owned prior to March 1, 1913; upon cost, as of the date of acquisition if purchased subsequent to March 1, 1913; and upon a "discovery" basis if the mine was discovered after March 1, 1913, The "jab" for mine valuations as of March 1, 1913 and for discovery valuations and depletion was not as bad as it has been made out to be. Thousands of valuations and estimates of reserves were made and agreed upon between taxpayers and Internal Revenue Service engineers and as the years went on the answers have been found to be "reasonable." However, human nature being what it is each case was a battle of wits - of a sort - and many resulted in severe differences of opinion and litigation. As tax rates increased the situation was not bettered. I could talk for several hours on this phase of depletion but it is all past now andwould not give any real service or better understanding of the matter.

Jan 1, 1958

By C. Opoku-Ware, M. Kukay, P. Conrad

"This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 feet below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana. INTRODUCTION In an effort to improve Butte Area One natural resources, the research project was proposed to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU). Research by Blicker, et al. (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic VALUES ((Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown in an underground greenhouse located in the UMEC and will be planted in five areas located within the BPSOU designated for tree planting by the Butte Silver Bow government. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. They will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow."

Jan 1, 2018

By Jamal Rostami

With the recent technological advances; Tunnel Boring Machines (TBM) have become a viable economic alternative to drill and blast in hard rock excavation. These machines are finding increasing use in underground mine development due to the potential benefits they offer. The successful application of TBM technology to mining depends on the selection of the most suitable equipment and cutting tools for the rock and ground conditions to be encountered. In addition to required testing and geotechnical investigations, cutterhead design optimization is an integral part of the machine selection to assure a successful application of the machines in a specific project. This paper presents and discusses the back-ground of TBM application in a mining environment and the lessons learned, the process of conducting site investigation and the necessary laboratory testing together with machine selection and performance estimation for TBM use III mine development.

Jan 1, 1997

By R. W. O. Kersten

The shrinkage method of stoping with pillar support has been used at Agnes Gold Mine since mining commenced. Until recently, rock instability did not have any detrimental effect on safety or production. Presently sill pillars are failing not only on the current production levels, but also in shallower old worked-out areas. The incidence of failure raises the question as to whether the pillar dimensions are adequate at the current working depths and what their size should be at greater depths. The effect of pillar dimensions on the economics of the mining operation is of paramount importance because of the amount of ore that can be left unmined.

Jan 1, 1982

By Odin Wilhelmy

Agriculture in the United States today is becoming more and more a business, rather than a way of life. In the light of this, it behooves the farm-supply industries that provide the American farmer with his tools of production--feed, fertilizer, machinery, and the like--to give even greater attention than they have in the past to meeting the needs of the farmer-businessmen they are serving. Increasing competition among the companies that make up these industries merely accentuates this need for better service. An opportunity for such improved service, not yet fully realized, exists in the fertilizer industry today. That opportunity lies in the increased transportation of fertilizer ingredients by water. However, before the benefits inherent in this increased water movement of fertilizers can be fully realized, certain obstacles must be met and overcome. It is the purpose of this paper to outline the nature and magnitude of this opportunity, to point out some of the roadblocks and the steps that can be, or are being, taken to remove them, and to indicate some of the rewards that would logically stem from success in these efforts.

Jan 1, 1961

By Charles H. Grant

Communications in whatever we do, is one of the major problems we encounter. In an effort to provide a better understanding of the use of explosives, I am going to take a little different view of what explosives are, and how you might look at them as tools to fragment rock, and some of the problems encountered in doing so. First, let's take the explosive, and although there are many factors involved, I want you to consider these as being reduced to only two--shock strain imparted to the rock by the high early development of energy; and the other, the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc..

Jan 1, 1968

By R. Washnock, P. James

"INTRODUCTION Abstract Tankhouse iron control through application of new treatment technology to mitigate conventional bleeding losses is considered. Implementation is discussed and the treatment economics explored. A representative case is assessed. Treatment benefits and application drivers for specific scenarios are noted. Background Hydrometallurgical ore processing has become a significant metal extraction/production avenue in recent decades. In copper mining; the focus for this examination, around 25% of global primary copper production and nearly 50% of US production result from various hydrothermal leaching extraction approaches coupled to Solvent Extraction/Electrowinning (SX/EW) metal production. Generally such processing is favored over pyrometallurgical processes for lower ore grades and as such is finding growing use and is expected to remain a key processing route looking forward with average world-wide ore grades falling as known ore reserves become exhausted. Target Problem And Motivation In hydrometallurgical processing the production circuit may be thought of as a chain of interlocked recirculation loops (Figure 1). Leaching dissolves the target metal from the ore along with other ore components which contaminate the Pregnant Leach Solution (PLS). Iron is a common component in copper ores and, as a result, occurs fairly ubiquitously in copper Pregnant Leach Solutions (PLS) generated by leaching. Leached components migrate through the production circuit from left to right (Figure 1) through a net combination of chemical and mechanical transport mechanisms. Selectivity at the recirculation loop interfaces tends to retard rejected component migration through the production process. As a result, overall relative contaminant migration fluxes are slower than the target metal (copper) and the contaminants tend to build up relative to copper in the more upstream portions of the processing circuit over time with iron often being a significant contaminant. Further, while copper is continuously removed from the system in appreciable amounts, little contaminant exit occurs and the absolute contaminant amounts and concentrations also increase throughout the EW circuit over time."

Jan 1, 2018

By H. F. Haller

Large volume sand plugs are placed in tunnels to stem underground explosions at the Atomic Energy Commision's Nevada Test Site. Placement through long, narrow accessways is like stemming coyote holes and blast chambers in mining and construction. Experience with several other methods showed that pipeline conveying could be preferable. Small scale tests justified predicting a placement rate of 20 y. p. h. at 1000 feet, with a modified gunite placer. The initial production trial placed over 2000 c. y. and was estimated to effect a small cost saving after paying for new equipment. Initial problems included duct replacement and supply delays, dust, and other personnel hazards. Operations analysis and SOP'S reduced delays during the second field trial, minimized hazards, doubled production. Re cent re search and operations analyses produced data on abrasion resistant ducts, identified minor equipment modifications which can improve production, developed techniques for impact compaction to 90% ?maximum? and for extension of the practical range to 2000 feet. Twenty-two illustrations include an air consumption-distance chart.

Jan 1, 1967

By E. P. Lunghofer

Silicon Carbide and Aluminum Oxide were two of the early forms of man-made abrasives often referred to as synthetic and were invented at the turn of the century. Edward G. Acheson invented Silicon Carbide in 1893 and Charles F. Jacobs filed a patent for the manufacture of fused alumina from bauxite in 1900. Jacobs' patent provided a method for tempering the alumina by reduction and fusion to a degree of hardness and toughness suitable for abrasive purposes. These two inventions are the basis of the synthetic abrasive industry today. Improvements have been made in the equipment used in the process, however the process itself remains basically the same. In 1904 A. C. Higgins observed that hot spots developed on the shell of the pot furnace used in the reduction of bauxite. He found that by spraying water on the hot spots they could be prevented and, in addition, they failed to return in the same place. Higgins reasoned that the cooling effect of the water caused the melt contacting the metal shell to freeze as an insulating autogenous refractory. This suggested that an improved furnace design could be obtained by using a metal shell which is continuously flooded with water on the exterior surface. Paradoxically, a furnace required to contain tons of molten Aluminun Oxide was thus constructed of nothing but a sheet steel shell with no refractory lining at all. A test of such an arrangement was tried by Higgins with considerable trepidation and was found to be extremely satisfactory.

Jan 1, 1985

By Harry M. Conger

Kaiser Steel Corporation's Eagle Mountain Mine is located in the Colorado Desert, 60 miles east of Indio, California. Concentrates from the mine are shipped by rail 164 miles to the company's steel mill at Fontana, and also to Longbeach, California for export. Temperatures are typical of the lower desert ranging from a high of 120 degrees in the summer to a low of 25 degrees in the winter. The average annual rainfall of about two inches comes mainly as cloud bursts during the summer months. From its inception, the Eagle Mountain Mine has had the problem of breaking its mine rock. Practices followed from 1949 until 1962 were very costly, did not produce uniformly good fragmentation, and were incapable of sustaining high production. During this period, every conventional type of explosive then in use was tried and found to be unsatisfactory for one reason or another. The first slurry test work at Eagle Mountain was started in 195E and finally by 1962, after having tried all the slurry mixtures then available including some "home made" formulas, a metallized slurry was perfected at the mine which overcame all of the disadvantages of former blasting methods.

Jan 1, 1965

By Michael Davis

In the fairly recent past, with a history of cheap and abundant energy, it has been possible to predict with reasonable confidence that world energy demand would continue to double about every 15 years. Those who attempted to forecast the role of nuclear energy in future electricity generation could also start with the fairly safe assumption that electricity demand would increase even faster : with a doubling in demand about every 10 years. To estimate the likely future world demand for uranium it was then necessary to introduce a number of other assumptions including the rate of penetration of nuclear energy, the timing and the specific fuel requirements. This series of assumptions naturally compounded the uncertainty, but, remarkably, usually led to future uranium demands being overestimated. Such a bias which has almost always been observed in predictions made over the past 20 years has increasingly made uranium producers sceptical when expected to match the forecast demand with increased production capacity and supporting reserves. This scepticism has, of course, been reinforced by the persistence so far of a buyers' market in uranium throughout the entire period of emergence of commercial nuclear electricity generation.

Jan 1, 1974

By Richard B. Stein

This paper will present an overview of several hydrometallurgical processes which can be used for sea-nodule metal recovery and some simplified economics. Before going any further, here are some of the basic figures from which the economics were developed. The first is to establish a representative composition for a typical nodule feed (Slide 1). This set of chemical analysis figures can be taken as typical for a deep Pacific nodule feed and shows manganese at 30%, copper at 1.1%, cobalt at 0.2%, nickel at 13% and iron at 10% for the metals of economic interest1.

Jan 1, 1982

By A. K. Bhowmick

Size reduction is very energy intensive and is the single most power-intensive operation in mineral processing plants. Research has shown that only a small part of the energy is utilized efficiently. One of the major thrusts of all equipment manufacturers has been to improve this efficiency. Choosing the right equipment to maximize energy utilization in any comminution application has always been the utmost criteria. Due to the high energy cost and depletion of good grade minerals, it is becoming essential to optimize all the subsystems within a given comminution system for the overall economic success of such ventures. Bradley Pulverizer Company of Allentown, Pennsylvania recognized this and started offering its Feeder Controller in 1988 for automatic feed control. After its first successful operation, Bradley made this as a part of all of their grinding system standard offering. It was also recognized that the Feeder Controller was just a beginning and more automation and controls would be required for an overall, efficient grinding system.

Jan 1, 1993

By James L. McGregor

St. Joseph Lead Company has been paying incentive bonuses for well over 40 years. In 1958 almost half of St. Joe's 1,860 employees in Southeast Missouri received some form of incentive bonus in addition to their guaranteed wages. There are very few payroll jobs in St. Joe s Southeast Missouri organization that lend themselves to a reasonably good measurement of production or quality, or both, where an incentive bonus is not paid. The term "Incentive Bonus" is used to differentiate betwen bonuses that are based on quantity or quality of work, and those that are merely additional pay of a standard amount per hour or day because of an employee being temporarily assigned to some unusual task, An employee temporarily assigned to a job where the working conditions make the job performance unusually difficult or where a special skill is used is often given a bonus of some standard amount per hour or shift in addition to his usual rate. This is merely a convenient way of paying something extra without disturbing the normal rate structure. Actually, it is differential pay similar to that almost universally paid for evening and night shift work. Bonuses of that type are not being considered in this paper. The basic reason or theory for paying incentive bonuses 9s to get improved production at lower cost, Unfortunately, it is often difficult, if not impossible, to find a yardstick by which it can be definitely proved that a particular bonus plan is accomplishing its purpose, It becomes, then, a matter of judgment on the part of management personnel as to the value of the bonus plan. The fact that St. Joe Lead Company has continued to pay bonuses for over 40 yews and has increased the number of bonus schedules used attests to a definite belief that they are beneficial to the company's successful operations.

Jan 1, 1960

By Michael P. Connor, O&apos

The Wing Hill Garnet Deposit, located near Rangeley, Maine, forsed through assimilation of Early Paleozoic metasediments by an intrusive Devonian gabbro. The resulting ore body is exceptionally large and high-grade, consisting of 50-70% almandine garnet. Following open-pit quarrying, the ore is trucked to Industrial Garnet Extractives' mill in West Paris for final processing. Two grades of abrasive are produced - a pure, premium grade INDUSTRIAL GARNET and the Lower grade co-product IGE UTILITY GRIT, both of which are available in a variety of sizes. INDUSTRIAL GARNET is marketed world- wide into a diverse marketplace including both loose grain and bonded applications.

Jan 1, 1985

By Rubén Pavón] [H.

Mexico, that for various years held the second place among the elemental sulphur producers in the world, now occupies the fourth position. Nevertheless, taking advantage of the recent increase in the international prices of the metalloid, it is expected that Mexico recovers its traditional position producing, for the first time, over two million tons of sulphur during 1974. Drawing from material stockpiled during the last years sales are expected to reach 2.5 million tons, at excellent prices in the foreign markets, but not so in the domestic ones where prices have remained practically static since 1955, in spite of substantial escalation of production costs. Of the two sources of elemental sulphur in Mexico, the frasch process extraction from the salt domes of the Tehuantepec isthmus where the most important reserves are located - is the one that shall have an important increment. An increase of production of lesser magnitude is expected from sour gas, since sulphur recovery plants wilI go on stream toward the end of the year in the new oil fields recently located in the State of Chiapas. Two Mexican corporations are expanding and improving rational Frasch extraction operations. Together with Petroleos Mexicanos' sulphur recovery from sour gas it is estimated that production during 1975 shall reach 2.5 million tons and, consequently, supply the domestic market and generate an important sum of foreign currencies.

Jan 1, 1974

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G's, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By Keith G. Wallace

In 1982 the U.S. Congress passed the Nuclear Waste Policy Act (NWPA) to provide for the development of an underground repository for spent nuclear fuel. This development will be managed by the United States Department of Energy. In 1986, the President selected three areas for site characterization to determine their suitability for the development of an underground repository; those sites were: 1) A site in volcanic tuff located at Yucca Mountain in Nevada, 2) a site in bedded salt located in Deaf Smith County in Texas, and 3) a site in basalt located in Hanford, Washington. At present conceptual repository designs are being developed for each site. A key element of a repository design is the underground ventilation system required to support construction, nuclear waste emplacement, and potential waste retrieval. This paper describes the preliminary ventilation system designed for the repository in tuff. The concept provides separate ventilation systems for the construction and waste emplacement activities. The paper further describes the means by which acceptable environmental conditions will be re-established to allow re-entry into previously closed rooms for the purpose of inspection, maintenance or retrieval.

Jan 1, 1987

By M. Niec

Poland lies at the junction of three geologic provinces: the East European Precambrian platform, the Middle European Paleozoic platform, and the Alpine orogenic belt comprising the Carpathian Mountains. However most of the rocks that contain mineral deposits and many of the recently explored and mined deposits are commonly hidden under thick overburden, sometimes up to over 500 m thick. The discovery of these mineral deposits was due to the combination of geologists talents for inference and the keen interpretation of geophysical data ultimately tested by drilling. Examples of such use of the state-of-the-art geology include the following: 1. Sedimentologic and paleogeographic reconstructions led to the discovery of 8.8 Gt of bituminous coal under 500 m of Jurassic and Cretaceous cover in the Lublin basin, 2. Tectonic and paleogeografic data suggested a potential for discovery of burried Upper Permian copper de-posits on the Foresudetic monocline; subsequent exploration discovered 75 Mt of copper and 0,17 Mt of silver, 3. Geological interpretation of gravity and magnetic da-ta combined with sedimentologic data and regional subsur-face geology resulted in the location of 1.3 Gt of Fe-Ti-V ore in the Precambrian basement of northeastern Poland under -500 m of cover 4. A combination of metallogenic theory and geological interpretation of regional geophysical mapping led to the discovery of Caledonian-Hercynian granites and grano-diorites with accompanying porphyry-type Mo-W-Cu ores below 300 m cover on the northeastern border of the Upper Silesian coal basin 5. Tectonic reconstructions based on gravity and seismic data combined with theory on the origin of native sulfur led to the discovery of 1.0 Gt of native sulfur under cover up to 300 m thick. Five deposits were found at the northern margin of the Carpathian Foredeep. The other deposits found include lignite, polyhalite, lead-zinc ores.

Jan 1, 1996