Search Documents

By Lawrence Adler

[An innovative framework is proposed which most efficiently and systematically handles the large quantity of information needed for equipment failure and other non-performance analyses. It is based on the accepted engineering dimensions of mass (material), length (geometry), and time (MLT). To these are added human and machine factor. Several failure "Modes" are identified for each dimension, which are then subdivided into specific "Types". Material Failure Modes such as Separation and Slip are easily recognized, but others had to be established. Geometric Failure Modes are usually straight-forward, Obvious ones include Geometrics Design and Stability with more synthesized. Time Failure Modes are again largely self-evident such as Life and Chemical Effects, others are needed. Human and Machine Factors as failure modes are loosely assembled. The results contain strengths, but also organizational weaknesses which are noted. Lacking a better alternative its use is recommended.]

Jan 1, 1989

By Brian H. Jasperse, Nicholson Peter J.

Gravity retaining walls have been constructed using Deep and Shallow Soil Mixing (DSM and SSM) since 1991 in the United States. These walls, for both temporary and permanent uses, were constructed by mixing cement with in-situ soils over a volume containing 100% of the required gravity wall zone. Modern design techniques have reduced costs substantially by forming the required gravity wall section as a composite mass. Using ratios of 15-35% by volume, treatment f the ground forming the required gravity section has reduced the cost from about $40 to about $20 per square foot. Design, construction and actual performance of these gravity walls are presented.

Jan 1, 1999

By E. R. Reeves

The mining industry has recognized the importance of engineering controls as a primary means of preventing hearing loss. The noise control treatments most commonly observed on drills and bolters during this study were windshields, sound absorbing material, and hydraulic motor covers. These controls were evaluated on machines at underground metal mines to determine the amount of noise reduction achieved by each control. The results indicate that absorbing material has very little effect on the noise level. The noise reduction attributable to the motor covers was dependent on the material used to create the cover. Properly installed windshields were the most consistent control.

Jan 1, 2004

By H. Reginald Hardy, Xiaoqing Sun

Rheological models are widely accepted as a means of describing the mechanical behavior of geologic materials. It has been found, however, that rheological models developed for a specific stress level on the basis of linear visco-elasticity generally are not satisfactory at other stress levels. It has been suggested that the parameters of such models should be functions of stress level (Hardy, 1965; Kim, 1971). In this paper, continuous functions of stress have been utilized to obtain the required variation of Burgers model parameters with stress level. The model developed using these functions provides a constitutive relation which reflects the real time-dependent behavior of rock materials. The new model is capable of predicting the creep behavior over a wide range of stress levels and also predicts mechanical behavior under different loading condition (e.g. constant stress rate). It is also interesting to note that the mechanical behavior of individual elements in the model appear to reflect the different stages of brittle fracture in rocks (Bieniawski, 1967), namely; crack closure, elastic deformation, stable fracture propagation and unstable fracture propagation.

Jan 1, 1986

By Rowan Melrose, Naj. I. Aziz, Arvind Misra

Mathematical models have been developed to simulate longwall heading development systems in Australian Longwall Mines. The models developed consider the effect of non concurrent cutting and supporting systems and concurrent cutting and supporting systems. They also consider the impact of operating parameters on each of these systems. Operating parameters that are considered include pillar dimensions, the use of surge cars, bolting time, shuttle car speed and heading advance per cycle. The effect of these parameters is considered with respect to production rates and also panel advance rates.

Jan 1, 1996

By L. Xu, N. I. Jayaraman, R. Bhaskar

The objective of this study is to develop a better understanding of the collection characteristics of dust measurement instruments used in mine dust control research with respect to properties of quartz and coal dust. Coal and quartz dust of narrow sues, with aerodynamic median diameters being approximately 2 µm, 4 µm and 10 µm, with quartz contents of l0%, 20%, 30%, 40% and 50%, were released in an aerosol characterization chamber using a fluidized bed aerosol generator. Dust was collected in MSA personal gravimetric samplers with l0-mm nylon cyclones, total dust samplers and Sierra 298 inertial cascade impactors. The samples were analyzed for mass and quartz content. A total of 21 experiments were performed for this study. The mass and quartz collection efficiencies of the total and respirable dust samplers and the impactor were determined. The data show that the amount of dust collected by the respirable dust sampler (respirable + oversize dust trapped in the cyclone pre-classifier) was, in general, less than the amount collected by the total dust sampler. The amount of dust collected by the impactor was higher than that collected by the total dust sampler. Quartz analyses of the airborne dust samples showed that the total dust and respirable dust samplers (including oversize dust) collect less quartz dust than at inertial impactor. The larger the median particle sire of the quartz and coal mixture, the lower the quart content of the dust collected in the samplers. For all three sires, the impactor was a better collector of quartz than the other instruments.

Jan 1, 1994

By J. W. Choung, J. A. Finch

Acid rock drainage (ARD) is a recognized environmental challenge facing mining industries. An ambient temperature ferrite (ATF) process has been investigated for treating ARD. Most nonferrous metal and calcium ions present in typical ARDs were found to be detrimental to the ATF process. Three approaches were examined, including C02 aeration, addition of complex agents and use of magnetic seeds. By introducing magnetic seeds in the ATF process, the interferences were minimized and all the precipitates formed with lime neutralization were magnetically recovered from a simulated ARD. The residual concentrations of major metal ions in the treated water were environmentally acceptable. The XRD pattern confirmed the spinel ferrite crystal structure of the products

Jan 1, 2000

By D. Robert Weir

The pioneers in pressure hydrometallurgy have provided a solid foundation during the past four decades. The pressure techniques are now capable of being used to push back the frontiers in the winning of metals. Pressure hydrometallurgy has been used to meet the objectives of extracting metals; purifying metal solutions, recovering metals; and rendering waste streams acceptable for disposal to waste repositories and the environment. Some examples of each of these functions are briefly reviewed. The applicability of pressure techniques to the recovery of precious metals is discussed.

Jan 1, 1985

By Scott G. Britton

Up to now, the hands-on approach to construction has been stressed. This chapter reviews the basic tools available for construction design and monitoring of a construction project. It is divided into three discussions, all under the general title of computer aids, since the trend for using these tools-is via the computer. In the context of our discussions, the focus for computer aids will be on the use of evaluation and analysis techniques for coal mine construction applications, including mainframe programs, CPM techniques, as well as mini and microcomputer applications. Although the presentation of material in this chapter may be detailed at times, by no means does it cover the entire field of computer applications for design or project scheduling and monitoring. It is only an attempt to illustrate the possibilities that are available to construction and mine engineers. Interested persons can pursue computer applications for coal mining by reviewing Computer Methods for the 80's. by Alfred Weiss, editor, published by SME-AIME.

Jan 1, 1983

By J. J. Schwoebel, M. J. Mavor

Rapid coal extraction techniques in gassy mines may strain a ventilation system if a degasification approach is not utilized. Design of mine ventilation systems requires estimates of gas emission rates from unmined coal into the existing mine workings. A degasification system for a specific property can be properly engineered to improve mining economics if the proper geologic and reservoir information is collected. This paper describes methods to determine the degasification rates for horizontal boreholes and vertical (stimulated and unstimulated) wells and the rate of gas emissions into the mine workings. The methodology is demonstrated by a specific example. Horizontal boreholes drilled in advance of mining are demonstrated to be the most effective means of coal seam degasification and reduction of gas emissions into mine workings. The significance of the paper is that few published methods for these estimates are available

Jan 1, 1991

By S. Orr

Flow in heaps and dumps is a two-phase flow phenomenon, though for many applications it could be simplified as unsaturated flow. Unlike saturated flow (typical of ground water flow), where permeability is independent of other hydraulic parameters, unsaturated flow permeability depends on the degree of saturation and/or on capillary pressure. Several recent field studies suggest that flows in heaps and dumps tend to concentrate in preferred pathways, bypassing much of the ore. Different preferential flow phenomena are triggered, promoted and influenced by different heap structures, by pretreatment, by the composition of the leach solution and by application rates and schedules. The structure of heaps and dumps is determined and affected by every stage of their construction -from blasting to crushing to conveying and stacking of the material. History of heap construction and operation combined with monitoring, mapping and certain field tests can reveal patterns of flow and transport in a given heap and can shed light on the physical mechanisms behind it. Such insight can provide a first cut on heap leaching enhancement by either eliminating or bypassing physical barriers to flow and leaching. Based on the understanding of the heap structure, advanced flow and transport models can be constructed and further enhance the insight. This insight is essential for understanding cause and effect and can provide a basis for decision making. Further, based on the physically-based models, an intelligent control agent, such as MRDS1, can learn and build a self-learning representation (or a model) of the complex heap leaching system, followed by dynamic optimization and planning of heap leaching and heap rinsing.

Jan 1, 2003

By Sam H. Patterson

The advances in knowledge of world bauxite resources in the last few decades include contributions to the geology of deposits, discovery of large resources, shifts in availability, and changes in. the industry in response to political and economic pressure. Improvements in the understanding of geology have resulted from the larger numbers of geologists working on bauxite and better exchanges of information. The large deposits discovered are mainly the laterite type in tropical regions. These discoveries have led to major increases in bauxite resource estimates as well as to shifts in bauxite availability and in the ranking of producing nations. Changes resulting from political, environmental, and economic pressures have resulted in increased costs of bauxite and in renewed interest in potential nonbauxite sources of aluminum. Aluminum is produced from nonbauxite raw materials only in the U.S.S.R.; however, research on extraction processes or investigations of nonbauxite alumina resources has taken place in several countries.

Jan 1, 1984

By Kot F. v. Unrug

In spite of extensive research and accumulated experience from mining operations, appropriate coal strength values for pillar design remain debatable. Coal strengths determined in the laboratory on standardized samples vary widely among various coal seams with poor repeatability. Penetrometric in situ strength testing obtains multiple measurements at multiple horizons within the coal seam to provide a strength profile. Alliance Coal has used that method in many of its mines for pillar design. Pillars in these mines perform well. This paper presents a series of case studies and discussion of issues related to coal pillar design. The analysis demonstrates that the proposed default in situ strength of 900 psi is appropriate when no other data exist. However, in the case of appropriate strength measurements combined with analysis of pillar structural composition, differing values can be used successfully. In areas where the penetrometric derived in situ strength is greater than the standard 900 psi in situ strength, reserve recovery has been optimized as required by law without compromising safety.

Jan 1, 2009

By David Sainsbury, Bevan Thompson, Yuejun Cai

The practice of placing loose rockfill as passive support in open stoping voids, of narrow vein mineral deposits, lends itself to the sterilisation of substantial mining reserves in the requirement for regional crown/sill pillars. Significant benefits are to be gained by the Australian mining industry via the development of improved guidelines for the extraction of such sterilised mine pillars. The application of selectively injecting specifically developed ettringite (calcium sulphoaluminate hydrate) type cement grout into loose rockfill, enables an artificial pillar to stabilise the surrounding rockmass and prevent the caving of loose rockfill from the previously backfilled void during extraction of remnant crowdsill pillars. This paper presents the results of laboratory testing used to reduce the technical risks associated with the design of cemented rockfill pillars. A laboratory testing program was devised to investigate the critical parameters influencing the performance of a stabilised rockfill matrix, along with the critical parameters influencing the interpretation of laboratory test samples. The factors investigated include; sample size and shape, particle size distribution, curing time, water quality, cement : water ratio and the confinement effect.

Jan 1, 2001

By Douglas J. Uhren, Gary W. Gilbert

This paper describes the risk elements associated with difficult glacial geology, including boulders, heavy groundwater inflow, and potential running soils all coupled with a potentially corrosive service environment. The matrix workshop for the 168-inchfinished diameter sanitary sewer interceptor tunnel in Columbus, Ohio is assembled with the Design Team and the Owner’s design, operations, and fiscal staff. Corrosion protection alternatives are compared against cost and non-cost parameters with relative risk and weighting factors assigned. The Owner working in cooperation with the Design Team uses the matrix workshop to se

Jan 1, 2001

By Randy Sandrik

Sampling has evolved at two large underground limestone mines as conditions and product requirements have grown tougher over 100 years of mine life, requiring innovative techniques to insure delivery of high purity limestone. Sampling insures delivery of consistent product to customers at the lowest possible cost. Statistical considerations have evolved from simple data collection to predictive and process capability analysis. Sample methods include borehole samples, face (using a proprietary face-sampling device), and total plant feed automatic, process, and final product sampling. Lessons learned, while keeping costs at historically low numbers, include the importance of geological models, exploration drilling density, face sampling, and blending of ore.

Jan 1, 2005

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive's velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By Albin E. Anderson

The PSM System has been available to the mining industry for nine years. During this time, many of the more than 160 Systems sold have been put to practical use and have provided the owners a handsome return on investment. In this paper, the author will briefly discuss how the System works and how it can be put to use in automatic grinding circuit control. Throughout, detailed consideration will be given to the many factors that can significantly influence how successful a specific application is.

Jan 1, 1979

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963