Search Documents

By Philip R. Whitney

Precipitation of hydrous manganese/iron oxides in streams can be readily observed in much of the northeastern United States, and is apparently a common phenomenon in other glaciated areas (1,2,3,4). Deposition occurs when Mn-enriched ground or surface water enters the stream environment and encounters conditions of higher Eh and pH. The preferred location for deposition is in shallow, fast-flowing segments of stream; the oxides usually form as coatings on detrital material. The experimental studies of Hem(5) and a considerable amount of work on marine and lacustrine manganese nodules(6,7,8) suggest that given an appropriate substrate, deposition of manganese oxides may occur even when the water is undersaturated in Mn with respect to the oxides, due to catalysis by organisms or by silicate, carbonate, or ferric hydroxide surfaces. Once begun, manganese oxide deposition is autocatalytic (9). Studies of the distribution of oxides in various size fractions of stream sediments indicate that the thickness and prevalence of the coatings commonly increases with increasing particle size in the coarse sand and gravel size ranges. Figures 1 and 2 show a fairly typical distribution of leachable metals over nine size fractions from 62 microns up to 8-16 mm. The leaching solution used was neutral ammonium citrate with hydroxylamine hydrochloride, which effectively removes the oxide coatings without significantly attacking most silicates, carbonates or sulfides. Figure 1 shows metal content as ppm of the total sample; figure 2 shows' the same data as micrograms of metal per square millimeter of surface area.

Jan 1, 1975

By W. R. McDonald

The U.S. Department of the Interior, Bureau of Mines, conducted field tests on acidic copper tailing as part of its program to devise, improve, and demonstrate technology for stabilizing mining and mineral processing wastes. Results will be presented from successful 1/8-acre and 1-1/2-acre demonstration revegetation plots established in 1973 and 1974 on an abandoned copper tailing pond located on public land adjacent to Holden Village, Wash. The tailing was neutralized with treatments of either dolomitic lime or limerock and fertilized with processed sewage sludge and/or commercial fertilizer. Plant growth covering 60 percent of the surface was achieved on both test plots. Regar brome, Tegmar intermediate wheatgrass, and tall wheatgrass provided the best plant growth and surface coverage. In neutralizing the tailing, the target pH of 6.8 was not achieved; however, good plant growth occurred in areas where the pH ranged from 2.9 to 5.8.

Jan 1, 1979

By Saul Escalara

Data on sulfonate adsorption by silicate minerals are very scarce in the literatures. Perhaps the only comprehensive paper written on the topic was done by Fuerstenau and Bhappu (1); this work dealt exclusively with quartz but included many important suggestions as to the form and nature of the hydroxy-sulfonate species of some cations formed during the conditioning step and their effect on the flotation response of quartz. Another paper by the same authors (2) contains additional data on the role of hydrolysis in sulfonate flotation of beryl. As postulated by Fuerstenau and Bhappu, a solid form of cationic sulfonate functions as the collecting species to produce flotation of quartz and beryl. According to the authors, the solid compound is a hydroxy-sulfonate of a given cation, where the hydrogen of the hydroxyl part provides a means for bonding of the species to the mineral surface; thus, the presence of hydroxyl in the neutral precipitated compound is of primary importance to produce flotation. Although the preceding examples illustrate the effect of a sulfonate collector in silicate systems other than plagioclases, they are important as examples of processes of hydroxy-sulfonate complex formation. Since the plagioclase minerals con¬tain Ca(II) and Al(III) cations, which are very reactive in sulfonate media (1), the formation of hydroxy-sulfonate compounds with these cations released from the solid phase may well prove to be the cause for their flotation.

Jan 1, 1973

By Ted T. Biddle

The world energy crisis has created a greatly expanded exploration program for energy fuels. The demand for materials required for drilling operations such as barite, which is the primary component of drilling fluids, has increased proportionally. As in the case of many other minerals, existing high grade barite mines are no longer capable of producing the required tonnage. Consequently, exploration and development of lower grade ore bodies has been increased. The need to produce a high quality product at maximum recovery rates, along with the ever changing economics affecting both selling price and production costs has triggered accelerated research programs toward more sophisticated and efficient beneficiation methods. Taking into account the specific gravity differential between barite (4.5) and the normal gangue minerals such as silica and calcite (2.7), gravity concentration methods are the prime consideration with flotation as a scavenging process. Greater emphasis on particle size liberation, size reduction and concentration is also indicated. In order to accomplish these objectives, it has been necessary to revert back to the old adage, "Recover your minerals as soon as they are free."

Jan 1, 1980

By Ping Li, Baokun Zhou, Lei Yang, Changfeng Li, Erhui Zhang

A uniaxial compression experiment was conducted on standard sandstone specimens to explore the sandstone’s mutation characteristics and early warning interval during deformation and failure. Meanwhile, acoustic emission (AE) and digital image correlation (DIC) techniques were introduced to realize multi-field analysis and cross-validation from the stress field, deformation field, and elastic wave field. The mutation characteristics of rock failure were investigated based on the cusp catastrophe theory. The results showed four mutation points in the destabilization process of sandstone: compressional density, yielding, destruction, and residual retention. As an internal activity characteristic of the sandstone failure process, AE directly reflected the dynamic failure process of sandstone. The stress variation was closely related to the evolution of AE characteristics. Sandstone loading failure was a process of the mutations of releasable elastic strain energy, dissipative energy, and releasable elastic strain energy. The mutation of dissipative energy was used as the starting mark of the sandstone warning state, and the second mutation of releasable elastic strain energy was used as the end mark of the sandstone warning state. Besides, the warning range corresponded to the loading time of 178 to 208 s. Finally, the sandstone instability warning interval was re-determined from deformation field evolution characteristics in the sandstone damage process, with a loading time of 180–204 s. This was consistent with the warning interval specified using the cusp catastrophe theory. The combination of AE, DIC, and cusp catastrophe theory revealed the mutation characteristics and early warning interval of sandstone failure. Hence, the results provide significant importance to predicting rock failure.

Aug 23, 2023

By C. Leal

Modern production has as goal to reach high and uniform quality in their products. To success with this, it is essential to have a good knowledge of the different variables involved in the process. Investigation or analysis of a process or system has as references the measurements of the variables. These measurements are presented normally in form of data. These data are measured in intervals over time. The aim with measurement of the data in a process is to obtain information about the state of it in order to have it under control. Other goal is to know how the results are affected by the process variables to improve upon product quality, redunding manufacturing cost, better pollution control etc.

Jan 1, 1994

By B. K. Mishra

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills (14-18 ft). DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important factors such as the configuration of the liner and the geometry of the lifting surfaces are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill with particular emphasis to large diameter mills.

Jan 1, 1992

Since 1955 Gaspe Mines has produced 144 million tonnes of ore, averaging 0.87% Cu, mined from two open pits and underground workings. In 1994, four exploration drill holes discovered a buried porphyry/skarn Cu-Mo deposit at depths of between 1000 m and 1700 m below the top of Porphyry Mountain. The mineralization and alteration associated with the Porphyry mountain quartz monzonite does not outcrop. A total of 19,500 m of drilling in 12 drill holes has outlined 200 million tonnes grading 0.73% Cu and 0.08% Mo. Mineralization occurs as veins and disseminations of chalcopyrite and molybdenite. Drilling and feasibility studies continue.

Jan 1, 1998

By Anthony Harding

In a world of technology and electronic communication, it is easy to forget what engineers do best with a problem: sitting around a table, exchanging views and ideas with sketches and respecting everyone?s view. This was the approach adopted in the project to arrive at a solution for the cross passage opening sup-port for the Seattle University Link Extension. Schedule and space constraints usually impede concurrent cross passage excavation and tunnel boring machine (TBM) operation. And where the space is constrained, opening support solutions that maximize available cross sections are of great benefit. While there are a number of solutions that minimize space, some of these solutions can require expensive steelwork and extensive drilling and fixing. However, following a detailed round-the-table discussion of the options and constraints, it was identified that a shotcrete shell would not only limit obstruction of the space during installation, but also permit easy installation, particularly around services, and avoid costly steelwork and drilling and fixing.

By B. Mishra

This paper presents a rock mechanics investigation of the time-dependent behavior of the rock immediately surrounding the excavation in a hypothetical one-entry coal mine based on the geology of the Illinois coalfields Research in the area of time-dependency is almost nonexistent and, therefore, this research was performed to make inroads into this neglected research area. Numerical analysis of a typical one-entry coal mine in an Illinois basin was performed using the commercial finite difference program FLAC3D. The immediate roof of the coal entry was assumed to be a shale formation. Shale in other formations has shown a tendency to creep with time. Therefore, in this study the authors modeled the shale in the roof using time-dependent characteristics. The input properties were taken from laboratory creep tests performed on shale. Model runs were performed at different stages, mimicking the progressive excavation of the entry. The model results showed that stresses in the roof attained the limit of yielding. Using Mohr-Coulomb failure criteria, potential zones of failure were also predicted. The results showed that the current computational capacities are sufficient to explore this previously uncharted territory of ground control.

Mar 1, 2014

By M. N. Herrera

The bioleaching of mineral sulfide pulps in a bench-scale rotating drum reactor has been studied. The reactor includes horizontal paddles in the inner wall for lifting of the mineral pulp. The performance of the reactor was tested in the bioleaching of a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans strain (ATCC 19859). The concentrate was efficiently bioleached at 50% pulp density with the drum operating at 0.5 -1.0 rpm Attempts of bioleaching the concentrate at the same pulp density in conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows to operate at much higher pulp densities than the conventional stirred tank reactor. This behavior is explained in terms of an improvement of the bacterial activity due to a better control of the attrition of the mineral particles.

Jan 1, 1997

By Y. M. Jiang

Many underground instabilities, such as excessive shield loading and roof falls, occur at longwall faces causing safety problems and production losses. Such instability problems are directly related to roof conditions which can be categorized using geological information. . However, most geologic information describing anomalies and variations of immediate and main roofs are not available before mining resulting in unexpected problems in a longwall face. It is apparent that the evaluation of these geologic anomalies provides a great benefit for longwall stability. The purpose of this study is to evaluate roof categories associated with geological anomalies employing fuzzy set theory. The evaluation is based on real-time monitoring information, such as shield leg pressure, developing load on shields, intervals of periodic weighting, and the ratio of developing loads during periodic to normal times. This paper introduces the application of fuzzy set theory for characterizing roof conditions and evaluating of roof similarities.

Jan 1, 1995

By L. Michael Kaas

Any increasing number of restrictions are being placed on mining management's ability to pursue profit. Raw materials pricing, the cost of capital equipment, labor cost, and overhead costs, are becoming more difficult to control. Cost reduction is one of the few remaining areas in which management may still exercise its profit making ability. Equipment maintenance is an area where mine and mill management can readily reduce costs and increase profits. Why is this possible? First, maintenance costs comprise a large portion of total operating cost. Thirty to sixty percent of the operating cost dollar is not unusual. Even a relatively small percentage reduction in this cost represents a very sizeable increase to mining profitability.

Jan 1, 1967

By K. T. Mau

Hawaii is located approximately 2,500 miles from the mainland, but has basic needs for its thriving developing community. Cement is one of these needs Cement production in Hawaii is not without handicaps. The necessary raw materials are practically non-existent except for limestone. Even at that, the available limestone is marine in origin, coralline in nature and amorphous in characteristics - unlike calcite which is normally the calcium carbonate source for cement manufacture. There is no clay or shale for the argillaceous portion of cement raw mix. Hawaii being volcanic in origin is too young geologically for clays and shales to evolve and whatever there is, most likely is washed into the ocean.

Jan 1, 1982

By Evan J. Owen, Virginia T. McLemore

Rare earth elements (REE) and critical minerals are increasingly becoming more important in our technological society and are used in many of our electronic devices (such as cell phones, computer monitors, wind turbines, etc.), batteries, and magnets. Measuring REE and critical minerals in ashed coal approximates the REE and critical minerals in the fly or bottom ash remaining after coal is burned at a power plant, where REE and other critical minerals could be leached. In New Mexico, there are 26 coal fields in Late Cretaceous rocks in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, Rare Earth, and Critical Minerals) program. Higher concentrations of REE (as much as 2103 ppm total REE) are found locally in ashed coals from the basins. More chemical and mineralogical analyses are required to fully understand the distribution and origin of REE in these deposits. As the demand for REE increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics, perhaps even from coal.

Feb 1, 2025

By E. J. Hammer

In the crushing and grinding of metallics for beneficiation, the sizing is normally done to liberate the metals or sulphides for further processing to improve recoveries of the basic metals or minerals. The objective is to reduce the ore in size through various closely controlled stages to that degree of fineness which gives an economic liberation of valuable mineral, but which avoids as much as possible the production of sliming fractions. A different philosophy applies to the crushing and grinding of Gypsum. Our requirements normally demand controlled grinding and/or crushing of the material not only to a fineness suitable for further processing of the mineral into end products, but to produce various sizes of material which are them- selves saleable products. The majority of our tonnage ultimately ends up in stucco for Wallboard. Therefore, our mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off inter- mediate products to meet various Customer requirements. This forces us into compromises at times in our equipment installations, and our equipment must sometimes be more versatile and complex than we would like it to be. We try to process our basic rock, Gypsum, for the most efficient size reduction. We market 5 to 6 different sizes intermediate to the end product, which generally is the fineness of material to be used for stucco for Wallboard, and we do this with controlled crushing, grinding and sizing cycles of the material. To summarize, we use a different philosophy of crushing and grinding than the metallic field which uses comminution or crushing and grinding to improve recovery, whereas we choose our equipment to crush and grind primarily for product performance.

Jan 1, 1969

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

By Bee R. Waples

The Alimak Raise Method, using the Alimak Climber, has proven to be a new, fast, economical method of driving raises at the Iron King Branch of Shat-tuck Denn Mining Corporation, Humboldt, Arizona. In order to fully understand the advantages of the Alimak Raise Climber, it is necessary first to describe the basic machine; second, a complete cycle of a raise round; and third, the comparative speed and economy afforded the Iron King operation by using this new method of raise driving: The raise climber consists of a drilling platform that is raised and lowered by two 6.2 HP compressed air motors that drive, through roller chains and sprockets, three worm gears connected in series. These worm gears drive pinions which grip the guide rail rack. The worm gems are fitted with spring-loaded couplings so that a small rock or grit in the rack is passed over without disturbing the mesh between the rack and the other pinions.

Jan 1, 1961

By D. A. Longhurst

Improper size distribution of the grinding media in a multicompartment mill can be a source of many operation problems encountered. Inefficient use of the power expended for grinding, and an undesirable product size distribution are two frequent resultants. It is necessary to resize the grinding media in the leading mill compartment at time intervals related to the abrasive nature of the material being processed. In practice, this is done when time permits and with sketchy guidelines, if any. Maintenance of the grinding media size distribution can be scheduled, and would be, with a realistic method supplied to the user.

Jan 1, 1984

By Jalal Vakili

In designing very large excavated slopes which are becoming increasingly common in both mining and civil engineering projects, the most important decision of the engineer is the selection of a slope angle. The purpose of the geotechnical study of the slope is to ensure reasonable stability of the slope in the most economical way. Because the rock mass composing each slope is unique, there are no standard solutions for slope stability analysis. A practical solution is formulated from the basic geologic data, engineering properties of the rock, geometry of the slope, and ground water observations. Stability analysis consists of analyzing the forces causing and resisting slope failure. There are several methods of slope stability analysis. The limit equilibrium method evaluates the overall stability of the sliding mass just on the verge of slip, using some or all of the three equations of static equilibrium of a plane problem. The stress-strain relationships of the rock mass are not considered. Method of analysis include the assumption of the shape of the slip surface. Peterson (10) introduced the Swedish method of analysis in 1916, which is based on cylindrical sliding surfaces. Fellenius (4) in 1926 extended this method and introduced the method of slices. This method was refined by Bishop (I) in 1955 and later used by Morgenstern and Price (8) in 1965. In many cases layers of extremely soft strata or strata weakened by neutral stress cause failure to take place by translation along plane of weakness instead of by rotation on a circular surface. In this paper, a slope with a horizontal layer of weak meterial is selected for analysis. This is a usual case for open pit lignite mines where lignite seam may be non-cohesive and 'weaker than the overburden rock or a soft clay layer underlies the seam. It is also a common case of rock fill dams supported on a foundation stratum of clay where the strength of the clay layer is less than that of the rock fill. It is shown that utilizing this method, the location of potential failure surface and the value of the minimum factor of safety can be calculated directly and the trial computations of factors of safety for a number of assumed failure surfaces are not necessary.

Jan 1, 1982