Search Documents

By D. A. Bird

Geochemical models using published thermo-dynamic data and laboratory derived kinetic rate laws allow prediction of post-closure pit lake geochemistry at open pit mining sites. A combination of "forward" and "inverse" modeling techniques can predict the pit lake geochemical evolution from initial infilling to eventual steady state attained decades or centuries after closure. Computer codes have been developed to model chemical reactions such as pyrite dissolution, describe the ground-water flow regime, and provide rock-water ratios. The incorporation of site specific information, such as ultimate pit dimensions, geologic and hydrologic data, acid generating potential (AGP) vs. acid neutralizing potential (ANP), and laboratory derived kinetic rates, allows application of the model to open pit mines at any stage of development.

Jan 1, 1994

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By D. D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a cost-effective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Feb 23, 2014

By C. C. Clark

The national Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system, it is necessary to know when the material has developed a compressive strength of approximately 1 MPa (145 psi), the early threshold for safe re-entry of miner and machine into shotcreted mine workings at this value, the material has developed enough strength to be self-supporting and to allow for installation of other ground support components that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on site in the first six hours after application using a partial beam test standard, a STM C 116-90 (1990). These advances were demonstrated in tests with five commercially available shotcrete mixes, sprayed as dry shotcrete using field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. Measuring the early strength properties of shotcrete directly at the mine site can improve mine safety by identifying appropriate re-entry times and providing a convenient means of conducting on site quality control during shotcrete applications.

Jan 1, 2011

Researchers at National Institute for Occupational Safety and Health (NIOSH) are investigating how fiber-reinforced shotcrete mix designs can be extrapolated from proven designs employing wire mesh. This paper explains the results of round determinate panel tests and relates the flexural strength and toughness of fiber-reinforced shotcrete to known energy absorbing properties of wire mesh. The energy absorbed with central deflection is strongly influenced by the amount of fibres. The higher the energy absorption the more load cracked shotcrete can support. Two types of fiber-reinforced shotcrete were investigated, one with steel fiber and another with polyfiber. The residual load supported in Round Determinate Panel Tests can be matched with the strength of wire mesh, thus providing equivalent bag strength values for fiber reinforced shotcrete panels. There is also evidence of a panel crack width comparison to the load holding capabilities of the fiber in the shotcrete mixes. In practice, this provides designers with a method for comparing the ground support provided by fiber-reinforced shotcrete with that supplied by wire mesh.

Jan 1, 2010

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By J. K. Brooke

Fluorine is a lively element in both its chemical and economic behavior. It was not isolated as an element until 1886 by Moissan. However, its principal source to this day, fluorspar, was known and its special merits recognized long before that time. Our own mining brother, Agricola, is credited with having named fluorite, the mineral name, in 1546 from the Latin, "fluere", to flow. It made things melt and was already being used as a flux. Because fluorspar has been found as a relatively common gangue mineral in metal ore veins, it has long attracted the attention of geological thinkers seeking to, explain the whys and wherefores of veins. Fluorine has been thought of as one of the principal mineralizers, holding metals in ascending vein solutions for deposition close enough to the eventual surface to be accessible for profitable mining.

Jan 1, 1964

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

Diesel particulate matter (DPM) presents considerable occupational health hazards in large-opening underground mines (LOUM). Previous studies have primarily focused on single-factor ventilation optimization, while this study innovatively integrates booster fan configurations and loading truck placements utilizing a coupled CFD turbulence– particle tracing model. Three distinct ventilation scenarios were simulated to evaluate their effects on DPM dispersion and dilution efficiency. Results indicate that dual booster fans substantially enhance airflow distribution, increasing air exchange efficiency; The migration pathways of DPM closely align with airflow trajectories, and air turbulence is the predominant factor influencing particle behavior within LOUM; Loading truck placement critically influences local DPM accumulation; Airflow effectiveness diminishes markedly with distance from booster fans, causing stagnation at distant working faces. The coupled CFD approach accurately captured airflow–particle interactions, offering valuable insights for optimizing mine ventilation strategies and effectively mitigating miners’ exposure to DPM.

Feb 22, 2026

By Günter Strappler, Max John

When tunneling through karstic terrain, diverse and complex karst structures are to be expected. By means of drilling ahead of the face using drill jumbos, these structures can be detected to such a degree that by applying proper support measures both open karst cavities and karst holes surrounded by boulders embedded in soft rock can be mastered without causing any break-outs. Support measures such as spiles ahead of excavation, sealing off cavities, back?lling with sand, etc. have to be planned schematically and adapted to the dimensions and formations of the karst structures on site. An essential requirement for a smooth excavation procedure is the availablility of all necessary tunneling equipment for excavation by drill and blast as well as for excavation of soil, with experienced tunnel engineers being in charge of any adaptions on site.

Jan 1, 2003

By J. Villeneuve, M. A. Reute, E. Verhoe

The objective of EU waste policy is to reintroduce used materials into the economic cycle, especially by recycling, or to return them to the environment in a useful state or at least a harmless state. To support decision-making in complex systems, the standardised ISO 14040 life cycle assessment (LCA) method can be used to quantify and to interpret the environmental repercussions of (changes in) a product system from cradle to crave related to a functional service unit. The use of the standardised LCA method at European level can be characterised as a damage-oriented or top-down method, which is often used in product design. Winning, extraction and processing of metals are part of the interconnected worldwide metals production system linked to product design, manufacture and recycling. This complexity cannot be dealt with using LCA. This paper will discuss a dynamic model that deals with this complexity, at the same time providing detailed bottom-up insight into the complex web of materials referred to as Metal Ecology. An example on the replacement on lead in solders will be discussed to illustrate this.

Jan 1, 2005

By Gealy W. Wallwork

The administrative processes of coal mines are becoming increasingly complex. As society evolves into a more complicated structure with greater emphasis on individuality, government regulations reach deeply into every activity in an effort to force individuals into a standardized mold. These contradictory pressures add an extra burden to the administration of a mining operation. Recent years have brought a substantial change in the skills needed by mine supervisors and managers. As a result, a better understanding of the administrative functions is necessary. The mine superintendent has the overall responsibility for the mine; for effective operation he must be sufficiently knowledgeable to oversee all the complex functions that make up the mine. This chapter does not cover all the administrative requirements because of the variation in mine operation and in company policies and organizational structure. It does attempt to identify the administrative functions that would be required at a large mine with a preparation plant. It is assumed that the mine operation is decentralized with very little duplication of functions at the organizational levels above the mine. Thus each function is assumed to be relatively complete at the mine and under the general supervision of the mine superintendent.

Jan 1, 1981

By R. K. Mehta, M. G. Bersch

Characterization of an ore or mill product is routinely performed by time consuming and tedious chemical analyses, sink-float separations, etc. Additionally, these types of tests do not provide data concerning the interrelations and interlocking of the mineral constituents. This paper discusses some of the applications and capabilities of the Minerals and Material Science Research Center at The University of Alabama. Back-scattered electron images of coal, oil shale, complex suldfide, and tantalium ores were acquired using a JEOL 8600 electron microprobe with a NORAN (formerly Tracor Northern] 8500 image analysis system. Methods of analysis and typical results are discussed.

Jan 1, 1992

This chapter contains the edited transcript of the "Gold Heap Leach Information Exchange" session that was held at the 1990 SME/AIME Annual Meeting in Salt Lake City, Utah. The exchange occurred on the afternoon of February 27, 1990. The session was intended to act as a forum for discussing some of the more prominent operating problems associated with heap leaching precious metals. The information exchange was very successful. The exchange consisted of several panelists introducing and discussing different topics, follow by a comment and question period. This transcript contains the panelists' presentations as well as comments and questions from the floor and the panel. Extraneous comments and remarks have been edited out. Some wording has been changed for clarity, but the transcript is basically an accurate account of what was said. At the end of the transcript are two papers submitted as part of the panel discussion

Jan 1, 1990

By E. K. C. Chanda

The best use of available reserves to give good metal recoveries relies on short term mine production scheduling.-The aim is usually to produce a plan to guide mining in specific areas that will enable mine operations to deliver the budgeted tonnes and grade to the mill and keep within the long range mine plan. Thus, short term production scheduling is an important aspect of the open pit mine planning function. Since the 60's increased attention has been paid to effective production scheduling as a means of improving the economic viability of existing mines. Hence, mine scheduling scheduling systems have been evolving rapidly during the last two decades. These systems include manual techniques, computer based simulation, mathematical programming and more recently Computer Aided Design (CAD). Some general drawbacks of the current scheduling systems are that firstly, the costs of acquiring and using them are not at all insignificant especially for small to medium sized pits. Secondly, there is an inherent trial-and-error aspect in these systems. Thirdly, they tend to be suited for specific orebody geometries, hence lacking the necessary generality. For instance, the use of computer programs for planning open pits to mine stratiform orebodies raises problems which are not usually met when massive orebodies are considered. There for, a need exists to develop simpler but effective short term pit scheduling procedures suitable for stratiform type orebodies, considering their geometry and geology. This paper describes a PC- based model designed to assist the planning engineer in optimizing the short term production schedule in open pit mines with stratiform orebodies. The model is based on a combination of linear goal programming and deterministic mining simulation. The orebody model is made up of ore and waste mining regions where winning and and/or stripping are taking place. These shovel regions form the basic planning elements in the model. This approach does not require the laborious preparation and use of a regular block model. The computer program consists of main modules: (i) Data capture - processes the raw data into the required format for mine planning. (ii) Precedence mining constraints - checks the status of each shovel .region at the beginning of a given scheduling period with regard to geometrical mining constraints such as undercutting. (ii) LP- Optimization - provides an optimal selection of ore shovel regions which do not violet geometrical constraints for mining in the period, the objective, being to maximize the contained metal equivalent in the blended R-O-M ore and at the same time to minimize deviations in grade and tonnage from the call values. (iv) Post LP-Simulation - enables the user to smooth out the LP solution in order to adjust it to a practically executable plan and simulates mining of ore and waste for the period. Shovel allocation to selected ore and waste shovel regions, unit operations and depletion of reserves are executed in this module. Preliminary testing of the model for monthly production scheduling using data from Nchanga OPen Pit on the Zambian Copperbelt indicates that it can be a useful planning tool and gives acceptable results.

Jan 1, 1992

By Darrell V. B. . McClarty

In 1996, Rio Algom, Denison Mines and the Elliot Lake Research Field Station (ELRFS) formed a consortium to implement a regional environmental information management system (REIMS) for the Elliot Lake area in Ontario, Canada. ELRFS is an affiliate of Laurentian University in Sudbury, Ontario, The discovery of uranium in the Elliot Lake region in post-World War II led to the development of 12 mines and 11 associated mills between 1955 and 1958. During the late 1980s, declining world demand for uranium, combined with the discovery of high-grade uranium ore in other areas of the world, made the Elliot Lake mines uneconomical. As a result, all area mines ceased opera¬tions by the end of 1996. The eight facilities and three tailings management areas operated by Denison Mines and Rio Algom's five mining waste management areas contain 150 Mt (165 million st) of potentially acid-generating tailings. The areas cover 13.2 km2 (3,265 acres) and receive drainage from an additional 13 km2 (3,212 acres). The primary objective of the joint initiative was to implement a personal-computer-based, regional, environmental-information management system for managing historical data and ongoing environmental programs in the Elliot Lake region. The Elliot Lake consortium decided it needed an information system with an integrated, process-oriented and requirements-driven approach to collect and manage the environmental information. Following a study of environmental information management systems currently used by the mining industry, the consortium decided to base REIMS on the "Envista" product. This is a commercially available, environmental information management system marketed by Envista Technologies of Saskatoon, Canada.

Jan 1, 1999

By L. Hagenbuch

Off-highway truck purchasers know the amount of tonnes, pounds, kilograms, etc, a truck will carry. However just because a truck is rated at 240 tons may in no way correlate to what that truck will actually carry. Two numbers define the carrying capacity of an off-highway truck: 1. The weight carrying capacity of the truck; 2. The volume carrying capacity of the truck. These two numbers must be in sync or the amount of payload carried will vary from the carrying capacity of the truck. Currently the Society of Automotive Engineers (SAE) standard J1363 January 1985 defines the volumetric carrying capacity of an off-highway truck. However as is well known in several South American countries, the SAE standard overrates the truck’s effective volumetric carrying capacity 15% to 20%. This paper presents a method for measuring “effective” body volumetric carrying capacity, resulting in a truck body for carrying the targeted load, matched to the loading equipment that interacts positively with the truck chassis.

Jan 1, 2002

By Thomas D. Kaufmann, Robert C. Drury

Few factors are as important as fluctuations in aggregate economic activity and exchange rates in determining the profitability of mineral investments. Macroeconamic theory explains how the two factors are interconnected in today's world and in tomorrow's. We can use macro¬economic theory to lessen some of the risks in mineral investments. And in the current state of the world the risks are high. The above paragraph summarizes our argument. Our goal in this paper is to examine the nature of contemporary business cycles so as to explain their implications for the metal industries, particularly the implications for capacity. Thus, our first section examines the workings, causes, and history of the recent economic fluc¬tuations. In doing so we must understand how current world economy is interconnected, that is, how economic events in one country are trans¬mitted to the rest of the world. Our view is that governments and central banks are key actors in the creating of economic fluctuations. Then, in section two, we work out the implications of section one for the metal industries focussing on comparative advantage, trade, and capacity decisions. Over the last fifteen years the world economic system has had slow overall economic growth and has had strangely unpleasant recessions. While future business cycle will not repeat the de¬tailed pattern we have seen, there will be similarities. The similarities need to be under¬stood before investment occurs. The slow growth in the world economy since the early 1970s has aggravated the problems from business cycles, created its own problems, and has partially hidden the effects of other events. Major realignments of currencies are likely to take place over a business cycle. The nature of the causes of the cycle will determine the direc¬tion of change in the exchange rates. For example, whether a USA recession will be accompanied by a weaker or a stronger dollar will be determined by the cause of the recession. The realignment of currencies over a business cycle leads to a realignment of comparative advantage in the metal industries. Thus, not only will world metal consumption vary over the business cycle but the impact on various countries' metals industries will differ consi¬derably. Competitiveness often depends more on the value of the dollar than it does on inherent efficiency and wage rates. Capacity decisions are inherently riskier due to the country specific nature of exchange rate risk. A realignment of currencies changes the pattern of trade if and only if the country with the cheaper currency also has idle capacity. The importance of our topic is indicated by Table 1 which shows the impact of cyclical and exchange rate shocks on the USA metal industry. In the cyclical downturn, from the peak of 1979 to the trough of 1982, consumption dropped by a fifth to a third. Metal price moved in the same

Jan 1, 1989

By D. Buranek, J. G. Wulff, F. W. Gifford

I. INTRODUCTION During the past few years, the state of the art of disposal of solid and liquid waste products from uranium mining and milling operations has experienced some rather interesting and significant changes. Some of these changes have resulted from technological advances in the milling operations and in the engineering aspects of the actual design and construction of the disposal facilities. However, the most significant changes, at least those which have had the greatest impact on the comparative cost and economics of modern disposal systems, have been environmental requirements and regulatory controls, which have become increasingly stringent in recent years. Without delving into the details of the myriad of new laws and regulations which now control the uranium industry, it can be stated with reasonable confidence that one of the principal purposes of more rigid state and federal controls over this industry is the basic desire to promote safer, more reliable and longer term means of effectively controlling and disposing of the potentially objectionable waste products resulting from uranium mining and milling operations. It is difficult to take issue with these basic goals because their need was spawned by past lack of awareness and inattention on the parts of both government and industry to the long term environmental problems and potentially hazardous conditions which can be created by limited planning and ill-conceived or poorly controlled and executed disposal practices. On the other hand, despite the good intentions of those who developed and those who are administering the regulatory controls now in effect, the basic danger exists that overgeneralization of the approach to disposal problems and overrestriction of the potentially acceptable solutions for uranium mine and mill waste disposal could have a significant, adverse economic impact on the mining industry and the ultimate consumers of their products. The regulatory pendulum, which perhaps swung too far toward lack of controls over uranium mill waste disposal in the 1940's, could now well be headed too far in the opposite direction, that is toward over-regulation in the form of restrictions based on technically unrealistic or weakly supportable

Jan 1, 1980

By E. W. Lindroos, Fred D. DeVaney, R. L. Bennett, R. W. Hernlund, W. R. van Slyke, W. F. McDermott, C. U. Keranen

INTRODUCTION Iron is the world's most widely used metal and constitutes about 5% of the earth's crust. Iron ores are found widely distributed throughout the world. Because of its wide occurrence and relatively low value, an iron ore to be merchantable must contain a relatively high percentage of the metal to be considered as a source of iron. Few ores containing less than 25% iron would be considered as ore unless they existed in large amounts and could be concentrated very cheaply. The grade of the ore, the ease of concentration, and the transportation cost to market are fundamental considerations deter- mining its worth. Iron never occurs as a natural metal except in meteorites. Most iron ores occur as oxides, and to a lesser degree as carbonates. A small amount is recovered as a byproduct from iron sulfides. Iron ore must be reduced (oxygen removed) to metal for use. Iron is marketed in many forms and combinations, such as pig iron and a great variety of steels. Iron is practically never pure as marketed but contains varying amounts of carbon, phosphorus, sulfur, and alloying elements such as nickel, chromium, etc., all of which affect the physical proper- ties of the end product. Please note that in this section all analyses ore on a dry basis and all tonnage figures are on a long-ton basis of 2,240 lb unless otherwise noted.

Jan 1, 1985