Search Documents

By Theodore Triplett

To assess the value of various subsidence mitigation techniques, twelve linear foundations were constructed above a longwall mine. The structures were monitored during and after undermining, and footing curvatures at the time of cracking were compared with predicted values. An unreinforced concrete footing sustained substantial damage. Other footings received varying degrees of damage, with inclusion of a sand layer significantly affecting performance. A post-tensioned concrete foundation suffered minimal cracking. Also, a technique developed by the Bureau of Mines is presented for determining the subsidence, slope, curvature and strain of the ground surface.

Jan 1, 1986

By K. L. Johnson

Networks of monitoring wells were established prior to mining at four longwall mine sites in the Appalachians to monitor the effect of mining on water levels, water quality and well yield. Two of the sites were located in stream valleys and the other two sites were located on hilltops. The depth to the mined seam ranged from 500-850 feet with the deeper cover being associated with the hilltop sites. Maximum declines in groundwater levels during and after mining were an order of magnitude less in the stream valley aquifers than in the hilltop aquifers. However, water levels in hilltop wells located outside the area immediately above the panel were unaffected. Water quality changes in wells as a result of longwall mining were negligible at all four sites. Increases in aquifer transmissivity and well yield were much more pronounced in the stream valley aquifers than in the hilltop aquifers. The significantly larger recharge area for the stream valley aquifers than that for the hilltop aquifers may partially account for the differing responses of these two classes of aquifers to longwall mining. These observations appear to be consistent with the stress-relief fracture model for Appalachian Plateau groundwater hydrology proposed by Wyrick and Borchers in 1981.

Jan 1, 1986

By Dan J. Van Roosendaal

A closely spaced grid of survey points was installed over the tensile zone of a longwall panel in southern Illinois and monitored daily during subsidence to document the complex ground-surface movements associated with dynamic subsidence. Vertical and horizontal displacements were used to calculate maximum tilts and principal strains within the grid. The dynamic nature of subsidence is made evident by changes in both the direction and magnitude of maximum tilts and principal strains. The maximum tilt (smax) of 0.036 and maximum tensile strain (Emax) of 0.027 were measured after subsidence and were oriented transverse to the longwall panel. Observations of surface fracturing were correlated with strain determinations to estimate a surface strain at incipient cracking (E;) of 0.006 to 0.009. Using shallow inclinometers, a linear variation of horizontal displacement with respect to depth was observed, suggesting a neutral¬axis bending mechanism for near-surface deformation. Horizontal displacements transverse to the longwall panel reduce to zero at a depth of 40 feet. A linear relationship between strain and curvature was used to estimate ground-surface curvatures associated with Emax (0.00068 ft-1) and E; (0.00015 to 0.00023 ft-1). The curvature estimates are consistent with published results.

Jan 1, 1986

By T. A. Ring

The bed filtration of colloidal particles has been modeled by performing a differential particle balance. The balance considered the localized particle deposition rate to be the sum of three rate resistances: 1) mass transfer to a region near the surface; 2) adhesion onto a partially filled surface; and 3) resuspension from a partially filled surface. The differential particle balance equations, one for the free particles and one for the adhered particles, were solved by a finite difference algorithm. The results of this model are compared to experimental filter breakthrough curves.

Jan 1, 1983

By Harry Perry

U. S. consumption of sulfur and sulfur products is expected to increase at a rate of 8 percent per year between now and 1980, largely as a result of their use in fertilizer markets. World consumption is also increasing rapidly, but at a-lower rate, about 6-percent per year. In 1965, sulfur recovered in the United States from purification of natural gas; nearly doubled from the 1956-1960 average; production from pyrites declined; and production of elemental sulfur increased 15 percent. Concern about air pollution resulting from sulfur oxides produced from the combustion of fossil fuel has lead to intensive research on methods of removal before combustion, during combustion (in-process methods), and from the resulting flue gases. If all the sulfur in fossill fuels were recovered, more sulfur products would be produced than were consumed in the United States in 1965. Removal of sulfur from coal before combustion could result in a product sufficiently-high in sulfur to be a suitable raw material for sulfuric acid manufacture. In-process methods produce solid sulfates, some of which may have commercial value. Flue gas removal' methods for sulfur oxidest generally result in the production of a byproduct either of sulfuric acid or sulfur. The projected sale of these materials significantly lowers the anticipated cost of sulfur dioxides pollution abatement. Alternate methods for sulfur dioxide reduction are discussed. The various proposed processes are described and costs are given for the various methods for which estimates have been made.

Jan 1, 1967

By Bryson D. Trexler

Man's activity in developing, operating, and abandoning a mine often affects the quality of the ground water and surface water. Acid water drainage from mines is an example of an impact from mining that results in degradation of ground and surface water. New flow systems are created by the mining activity. The mining made possible complex chemical reactions that, with water movement, create a discharge of low pH, poor quality water. Remedies for these problems fall into two general solutions: 1) treatment of the end product and 2) reversal of some aspect of man's disturbance of the natural system. The relative reversibility of various aspects of man's impact from mining activities ranges from relatively easy to very difficult, from economically feasible to economically infeasible, and from technically possible to essentially impossible with present knowledge. The relative reversibility of a mine-related problem cannot be assessed without first understanding the detailed physical interactions that combine to form the problem. Acid water drainage is a combination of the availability of several chemical factors with the availability of water for a transport mechanism.

Jan 1, 1982

By Galen G. Waddell

Several years of rock-burst research conducted by the Federal Bureau of Mines, in cooperation with the mining companies of the Coeur d?Alene Mining District, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem.

Jan 1, 1970

By J. J. Scott

Friction Rock Stabilizers, trade name Split Set*, is a new support system invented by the author and under development by Ingersoll-Rand and Lee-Norse Company. Split Sets are a substitute for standard bolts or fully grouted resin bolts and have certain advantages which are: 1. Improved safety for the miner 2. A rational design is possible based on rock mechanics principles 3. Supports can be made either to be yieldable or rigid 4. Supports can be used to build a roof beam or to suspend roof material 5. It is cheaper than the resin system and costs about the same as standard bolts.

Jan 1, 1974

By Ashutosh Kumar Bharati, Rajesh Rai, B. K. Shrivastva, Arunava Ray

Opencast mining method is one of the most productive mining methods available at present, which is generally associated with the removal and handling of a huge amount of overburden material. Hence it imposes a serious challenge of dump slope stability and that too, mainly in the case of internal dumps. The study is primarily focused on the stability of dragline dumps and the subsequent development of a rating system to classify the stability of dragline dump profiles. Initially, numerical simulation is executed through RS2 (Version 9.0) software, which is based on the finite element method. Thereafter, simulation results are used to perform the sensitivity analysis of various geometrical and strength parameters of the dump slope, and the two-factor interaction method is also incorporated into the analysis, this method included the dependency of closest parameters while calculating the sensitivity index, and thereafter, it is converted into the rating of each parameter. The strength parameter like the angle of friction and the geometrical parameter like slope angle of the bench between the coal-rib roof and dragline sitting level are assigned the highest rating value. Based on the overall rating of the dragline dump, the dump slopes are classified into various classes, viz., very safe, safe, vulnerable, unstable, and highly unstable. This classification proved to be handy in the quick estimation of the stability of the dragline dump and also gives an idea of designing optimum and safe dragline dump profiles. The developed classification chart has been validated by the previous research works and has found similar results.

Feb 15, 2021

By Yi Luo, Jian Yang

Subsurface strata movements and deformations associated with longwall mining operations in underground coal mines could cause various disturbances to subsurface mine structures, ground water bodies, and coalbed methane reservoirs. In order to assess those disturbances correctly and to design effective and efficient mitigation measures, it is necessary to develop an accurate prediction model for subsurface strata movements and deformations. Decades of research have demonstrated that variations of stratification and lithology in the overburden have significant influence on the subsurface strata movements and deformations during ground subsidence process. The key strata theory states that the thick and hard key strata serve as the backbone of the overburden and control the movements of the thin and soft weak strata located above them. From an engineering standpoint, the overburden strata are subdivided into several individual groups by the key strata with each group consisting of a key layer at the bottom and weak layers overlying it. A new subsurface subsidence prediction model considering the key strata effects on subsurface strata movements and deformations has been proposed. In this method, elastic modulus, specific weight, tensile strength, and uniaxial compressive strength (UCS) of each layer are used to identify the key layers and to determine the needed subsurface subsidence parameters. The influence function method, proven to be accurate and versatile for surface subsidence prediction, was employed to predict the subsidence on each of the overburden layers from mining horizon progressively upward to ground surface with the assumption that the predicted subsidence on a given layer serves as the subsidence source for the layer immediately above. The enhanced subsurface subsidence prediction model has been demonstrated with an actual case to show its applicability and improvement.

Jan 25, 2021

By S. T. Hall

The authors have previously described a method of enhancing the magnetic susceptibility of pyrite by a mild alkaline oxidative pressure leach (Hall et al, 1985). This finding was successfully applied to enhance the magnetic desulfurization of an Eastern Canadian coal (Hall and Finch, 1984). This paper reports on enhancement of the magnetic susceptibilities of iron-containing sulfides (arsenopyrite, chalcopyrite and marcasite) upon similar treatment. It also explores the application of this pretreatment in the magnetic separation of fine sulfides from oxides and other sulfide minerals. In the latter case galvanic interference effects have a serious impact on the potential use of this method.

Jan 1, 1985

By Debra Switzer, Swapnil Urankar, Douglas Watson, Steven Hunter, Chandranth Banerjee, Shashank Pathak

A hydrocyclone is a piece of equipment commonly used as a classifier in mill circuit operations. Traditionally, hydrocyclone performance is characterized by the classification efficiency parameter, such as cut size (d50c), sharpness of separation () and bypass (Rf ). A plethora of endeavors have already been made to develop parametric models to determine hydrocyclone performance that correlate design and process variables. In contrast to those studies, we made an attempt to develop an approach to derive required design parameters purely from hydrodynamic principles that provides a platform to optimize the operation of a hydrocyclone for a given application. In this selection methodology, we calculated the differential pressure at the air core, as well as the tangential velocity at the boundary of the air core from the vortex principle in a confined geometry at different operating regimes. A series of experiments were conducted using Weir’s Cavex® hydrocylone where process variables—such as solids concentration and feed flowrates—were experimentally studied to determine the key classification parameters. For the validation of the current approach we used the same process variables to derive design parameters and compared them with the existing design. The current approach can provide insights towards the selection of design parameters and can be useful for mining industry professionals to optimize different operating parameters of hydrocyclones to achieve the best performance.

Feb 1, 2024

By J. J. Crowhurst

The Carson Hill mine in Calaveras County, California, was explored and developed by Grandview Resources Inc., as an open-pit heap-leached operation, with production commencing in the fall of 1986. Grandview entered the district in 1983 after a 40-year period of quiescense, the initial contact being by Barden Stevenot, V.F. Hollister, and J.J. Crowhurst. The last dividend declared by the Carson Hill Gold Mining Corp. was 3 1/2$ per share paid in January 1943. The mine was originally discovered in August 1848 by Jim Carson. Preceding the entry by Grandview in 1983, Cyprus Mines explored Carson Hill in 1975, and drill exposed a mineral inventory of 7.3 Mt (7,982,000 tons) averaging 1.4 g/t (0.040 oz per ton) gold. From that time until the Grandview entry, R.W. Thomssen and B.E. Stevenot continued investigations into the potential of the deposit. Grandview successfully investigated many of the metallurgical problems involved with heap leaching the ore. Metallurgical investigations were con- cluded under the direction of R.S. Shoemaker. By November 1984, J.A.C. Ross had prepared a prefeasibility report that included the earliest Grandview investigations. This report concluded that the deposit contained at least 6.8 Mt (7,440,000 tons) of ore that average 1.5 g/t (0.045 oz per ton) gold and that this ore could be mined with a 2: 1 stripping ratio. A final feasibility report was prepared by D.W. Pringle in September 1985. It showed a final ore reserve of 14.7 Mt (16,160,000 tons) of 1.7 g/t (0.049 oz per ton) gold. Attached is a description of the geology of the deposit from an internal report covering Cyprus activity in 1975 and a brief portion of USBM IC 6940 (1937). General location and geologic maps attached are from the Pringle report.

Jan 1, 1990

By Keith Jones, Martin Knights, Timothy Watson

In 1996 a KBR (Brown and Root) led international JV was appointed to design and supervise an underground and surface package. The design of 6 km of tunnels, plus enlargements, deep shafts in glacial and sandstone deposits for the conversion of the existing LEP underground laboratory at CERN, Geneva adjacent to the Jura Mountains/Lake Geneva had to be undertaken in an operational environment and in conjunction with other underground constructions associated with the US$3bn refurbishment.

Jan 1, 2003

By N. Harrigle, Tsutsumi

Very fine wet sizing of minerals such as kaolin, precipitated calcium carbonate, lime milk, and clay slip is a difficult process to achieve using standard vibrating screens. With particle sizes ranging in the sub-microns combined with the agglomerating tendencies of certain materials, screen blinding becomes a serious issue. Sizetec, Inc. has developed an innovative screening equipment to help solve this problem. The High Performer Screen uses powerful linear vibrations to help break apart agglomerated particles and prevent screen blinding. Optionally fitted with the Air Explosion Screen Cleaning System, compressed air can be periodically injected into the screen underflow chamber to clean the screen surface without the use of water sprays. This paper highlights some of the key features of the Sizetec High Performer Screen and describes typical performance that can be expected based on results from various trials conducted in the kaolin industries.

Jan 1, 2002

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990

By Hans U. Bartholet

The bentonite industry in Europe includes both the smectite and hormite groups of clay minerals. The smectites are, essentially, a compendium of cationic differentiatable montmorillonite platelets which can be expanded in liquid media, whereas, members of the hormite group are characterized by fibrous and chain structured lattices which are non-expandable. As was pointed out in the March '78 issue of Industrial Minerals, each of the minerals in these groups has acquired a variety of names due to historic or regional usage.

Jan 1, 1979

By Elmer R. Drevdahl

During the last few years there has been a rapid increase in the development of the community or junior college throughout the United States, Some factors behind this development include the need for more college facilities to service the growing number of high school graduates, the desire of the public to provide some post high school education at reasonable costs, and the need to provide post high school educational opportunities not now provided by most of the universities and colleges. Many of the new community colleges provide at least three educational services including local opportunity to provide the first two years of a four year college program, two year technical-vocational programs of a terminal nature, and adult educational opportunities. The community college has the advantage of not being saddled with years of academic tradition which prevent it from changing to suit the educational needs of the community It serves. The flexibility of the community college in developing new programs, particularly in the technical areas, is going to provide industry with many of the badly needed technicians it is now unable to secure.

Jan 1, 1965

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By Ulrich Maidl

The use of EPB shields in the so-called mixed face conditions has set new demands to man and machine in EPB shield tunneling. EPB shields were initially conceived to drive in the pressurized closed mode in soft ground, whereas hard rock TBMs were designed to work in the unpressurized open mode. The present use of EPB shields in hard rock and mixed face conditions requires the combination of both technologies by finding best compromise solutions. This paper deals firstly with the geotechnical and mechanical interactions between machine and ground. Further on the critical points such as tool wear and tool replacement are exposed, together with a proposal of best solutions.

Jan 1, 2003