Search Documents

By J. Geyer, B. T. Burton, H. W. Newcomen

For open pits developed in tropical climates the upper portions of the pit walls are often located in residual soils and weathered rock. Due to the presence of relict structures, and the relatively low strength of the residual soils and weathered rock, design slope angles in these materials have to be developed by blending the results of kinematic assessments of geologic structures with rock mass stability analyses and traditional soil mechanics. Background information on the engineering considerations of residual soils are discussed, and the results of geotechnical assessments for proposed pit design of the Brisas del Cuyuni Project, located in southeastern Venezuela, are presented.

Jan 1, 2000

By Dennis P. Martin, Michael M. Fitz, James E. Friant

Methods for reducing the cyclic nature of drill and blast tunneling operations have been long needed. A miniature blasting system using 10 mm (.375 in.) holes, 0.91 m (36 in.) deep, and blasting only one hole at a time makes it practical for men to work behind a shield, remaining at the face during the entire process. A prototype automated module was developed to drill, load the hole and initiate the detonation without moving from the hole. A unique cost effective gell explosive and a novel, low cost initiation method were developed.

Jan 1, 1989

By William H. Mount

INTRODUCTION Effective mine ventilation is required to maintain a healthy underground environment for humans. Without effective ventilation, the environment can become unhealthy or hazardous as a result of the depletion of oxygen, contamination with toxic gases, or the buildup of an excessive amount of particulate matter (dust). Each contaminant has an upper limit of concentration that should not be exceeded within an 8-hr period. This is known as the threshold limit value (TLV). The TLV represents an acceptable level of exposure that should produce no ill effects. Unfortunately, more than one contaminant may be present at any one time and the effects of the individual contaminants may be additive, i.e., the effects of each contaminant must be considered simultaneously to determine the potential danger to miners. Possibly the greatest threat to mine-air quality is the uncontrolled underground use of the diesel engine. The diesel engine was invented in 1892 by Rudolf Diesel. His intention was to develop a power source that could burn coal dust as a fuel, but he was unsuccessful in that attempt and had to resort to liquid petroleum fuels (Johnson, 1975). In 1898, the diesel engine was intro¬duced into the United States by Adolphus Busch, who anticipated using it as a prime mover in factories and generating plants. At that time, the diesel engine was a very large and very heavy engine, designed for fixed installations. By 1919, lighter engines were being developed, and by 1931, Caterpillar was marketing a diesel-powered, track-type tractor (Henderson, 1975). Since 1931, the diesel engine has evolved into an extremely popular prime mover in medium and heavy-duty applications. Efficiencies now are on the order of 40% and improvements such as turbocharging and aftercooling have produced engines capable of generating power at a ratio of 0.3 kW/kg (1.0 hp per 5.0 lb) of engine weight. Although the diesel engine is relatively efficient as a mobile power plant, it is far from efficient in terms of the energy produced from the energy potential of the fuel. About 60% of the heat value of the fuel leaves the engine as wasted heat, with about 50% of that heat being emitted through the exhaust pipe and the other 50% being emitted through the radiator or cooling fins. Perfect combustion in an engine would produce only water vapor (H_0), carbon dioxide (CO_), and nitro¬gen (N2) as the byproducts. Since the diesel is not a perfect engine, each pound of fuel burned generates 5.6 m° (200 cu ft) of exhaust gas, containing about 0.009 m3 (0.33 cu ft) of carbon monoxide (CO), 0.009 m' (0.33 cu ft) of nitrogen oxides (NO, NO2, and NOD), and 0.57 m3 (20 cu ft) of carbon dioxide. The balance of the exhaust emission consists of free nitrogen and water vapor (Hurn, 1975). Contrary to popular belief, the diesel is not inherently dirty. Under normal operating conditions, a well-maintained engine neither smokes nor smells. However, the same well-maintained engine can and does produce toxic emissions. A diesel engine is not inherently safe and constitutes a distinct hazard to personnel. This chapter is devoted to a description of the various toxic substances that may be generated by a diesel engine. Although some of these substances may also be produced by blasting or natural causes, the focus of this chapter is on the relationship between the internal- combustion compression-ignition engine (the diesel) and the quality of the mine air. CARBON MONOXIDE Combustion Process During the combustion process (burning) of organic fuels, each atom of carbon combines with two atoms of oxygen, provided that a surplus of oxygen atoms is available. Thus, the carbon is oxidized to carbon dioxide. Most open flames, such as trash fires, camp fires, gas ranges, etc., produce carbon dioxide. However, with insufficient oxygen, incomplete combustion results as the carbon atoms each combine with one atom of oxygen to produce toxic carbon monoxide. Burning charcoal briquettes produce carbon monoxide because the combustion takes place inside the briquettes where sufficient oxygen is not available to the combustion process. Internal-combustion engines, whether burning gasoline or diesel fuel, also produce carbon monoxide. The only oxygen available to the combustion process is that trapped within the cylinder. If the amount of fuel delivered to the cylinder is excessive, there is insufficient oxygen for complete combustion and carbon monoxide production results. In a normally aspirated (nonturbocharged) diesel engine, the amount of air "sucked" into a cylinder is the same on every intake stroke, resulting in complete combustion only at low levels of engine loading, when small amounts of fuel are injected. Higher levels of engine loading cause larger amounts of fuel to be injected into the same volume of air in the cylinder. Unless the volume of air is increased, the combustion process becomes progressively less complete as the amount of fuel increases. Turbocharged engines are able to compensate some¬what for increased loading and increased fuel consumption. The turbocharger acts as a compressor for the intake air, forcing a larger volume of air into the cylinders as the engine speed increases. Hence the turbocharged engine burns cleaner than a naturally aspirated engine and produces slightly less carbon monoxide (Marshall and Fleming, 1971). Much of the underground equipment used today is powered by turbocharged indirect-injection diesel engines. Although these engines emit fewer toxic contaminants than naturally aspirated engines, they do not eliminate the problem. Since the turbocharger is driven by the exhaust gases, rapid accelerations can cause temporary overfueling of the engine until the turbocharger attains a speed sufficient to restore the correct air-to-fuel ratio. During this "turbocharger lag," the combustion cylinders contain insufficient oxygen, causing severe smoking and an increased output of carbon monoxide.

Jan 1, 1982

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

2.1 INTRODUCTION When total extraction of an opening of sufficient size is reached in a horizontal coal seam, the roof strata in the overburden deform continuously to reach a new equilibrium condition. The severity of deformation decreases upward toward the surface. As the downward saggings of the strata propagate and reach the surface, there will be a depression zone on the surface directly above, but extending beyond the edges of the underground opening. This is the surface subsidence basin or surface subsidence trough. The surface subsidence basin is circular in plan view, if the coal seam is horizontal and the mined-out opening is square in shape. But it is rectangular with rounded corners or elliptical if the coal seam is horizontal and the mined-out opening is a long- and thin rectangle or a short-rectangular, respectively (Fig. 2.1). Most underground openings (e.g., longwall panel) assume rectangular shape when total extraction has been completed. Theoretically the edges of the subsidence basin are the points of zero subsidence. But it is difficult to exactly locate the points of zero subsidence. Therefore in practice the points with vertical subsidence of 0.4 in. (10 mm) are used. The final subsidence basin is that which exists long after the mining has been completed, because its magnitude and shape are quite different from the dynamic subsidence basin formed while the face is moving. 2.2 CHARACTERISTICS AND TYPES OF DEFORMATION IN THE FINAL SUBSIDENCE BASIN For a horizontal coal seam, every point in the subsidence basin moves toward the center of the basin. Subsidence is maximum at the center of the basin. Any cross-section that passes through the point of maximum subsidence and either parallel to AB or CD line (Fig. 2.1) is a major cross-section along which principal directions of surface movements occur. However among those infinite numbers of major cross-sections, two specific ones are of special significance, not only because the magnitudes of surface movements are the largest, but also because they are the most easily identifiable directions, i.e., one that is parallel to the faceline at the center of the basin (CD in Fig. 2.1) and' the other is that perpendicular to the faceline but parallel to the diction of face advance (AB in Fig. 2.1). Nearly all the subsidence data obtained in the US have been derived from these two cross-sections, although some cross- sections parallel to CD but near the edges of the panel have also been included. In addition to moving horizontally toward the center of the basin, every point in the basin also subsides vertically. The magnitude of subsidence increases toward the center of the basin. Therefore surface subsidence is a three-dimensional problem and should be treated so in all cases. On all the major cross-sections, only principal subsidence and principal displacement occur. Since subsidence and displacement vary continuously in every major cross-section, three additional deformation components are de- rived, i.e., slope, curvature, and strain. On all other non-major cross-sections on the other hand the five components are accompanied by two additional components, i.e., twisting and shear strain. The seven components of the surface movement are defined as follows (Fig. 2.2): 1. Subsidence, S. On any cross-section, the vertical component of the surface movement vector is called surface subsidence. It generally points downward. But sometimes it points upward in areas ahead of the faceline or beyond the edges of the opening. In such cases it is a surface heave which is usually less than 6 in. 2. Displacement, U. On any cross-section, the horizontal component of the surface movement vector is called surface horizontal displacement. It generally points toward the center of the subsidence basin. But in steep terrain, it moves along the downdip direction 3. Slope, i. On any cross-section, the difference in surface subsidence between the two end points of a line section divided by the horizontal distance between the two points is called the surface slope of the section. 4. Curvature, K. On any cross-section, the difference in surface slope between two adjacent line sections divided by the average length of the two line sections is called the surface curvature of those two line sections. There are two types of curvature: con- vex or positive curvature and concave or negative curvature. 5. Horizontal strain, e. On any cross-section, the difference in horizontal displacement between any two points divided by the distance between the two points is called horizontal strain. If the distance between the two points is lengthening, it is tensile strain with positive sign. Conversely, if it is shortening, it is compressive strain with negative sign 6. Twisting, T. On the surface of the subsidence basin, the difference in slope between two parallel line sections divided by the distance between the two line sections is called twisting. 7. Shear strain, y. Shear strain is the changes in internal angles of a square on the surface of the subsidence basin or on any major cross-section. It is the summation of the differences in incremental (or decremental) lengths between the two opposite sides divided by the original distance between the two opposite sides. More precisely, the surface deformation indices (i.e., slope, strain, curvature, twisting and shear) are defined by derivatives of surface movement components. For simplicity, the x- and y-axes of the cartesian coordinate system are set to be parallel and perpendicular to the cross-section of interest, respectively. In such a coordinate system, slope and curvature along x direction are the first and the second derivatives of the vertical components (S) of surface movement with respect to x, respectively, or i, = ds/dx and kx = d2s/dx2. Horizontal strain along x direction is the first derivative of the component along x direction of the horizontal displacement,

Jan 1, 1992

By C. Heath

US coal consumption reached new heights in 1985, but production was constrained by excess consumer inventories. Domestic consumption of coal reached a record 742 Mt (818 million st) during the year. This is a 3.4% gain over the previous consumption high 718 Mt (791 million st) in 1984. An additional 84 Mt (92.7 million st) of US coal were shipped abroad in 1985, up 13.7% from exports a year earlier. Coal production in 1985 totaled 804 Mt (886 million st), 1.1% below the record 813 Mt (896 million st) produced in 1984. The slight decline in coal output is attributed primarily to a 13% drawdown of large consumer stockpiles built up in 1984 in anticipation of a miners strike that never occurred. Coal demand, and hence production, were also restrained by slower economic growth in 1985 and additional gains in nuclear generation of electricity. Domestic market requirements for coal in 1985 were mixed. Electric utility consumption rose 4.4%; coke plants consumed 6.7% less coal; coal requirements in the other industrial sector expanded by 2.1% and consumption in the residential and commercial sector fell 14.8%. The 2.2% increase in electric power generation in 1985 resulted in a 4.4% rise in utility coal consumption, totaling 630 Mt (694 million st) for the year. Twenty-nine of 45 states where coal-fired electric power plants were operating shared in the 26.7 Mt (29.5 million st) increase in 1985. Coal receipts at utilities fell by 16 Mt (18 million st) as these facilities worked off 21 Mt (23.4 million st) from stockpiles during the year. Electricity generation at coal-fired power plants similarly climbed 4.4% to 1.4 trillion kWh in 1985. This gave coal a 56.8% share of electricity generated from all energy sources compared with 55.5% in 1984. The average price of coal delivered to these facilities remained essentially unchanged during the year. It declined on 1.5% from $38.26/t ($34.71 per st) during the fourth quarter of 1984 to $37.70/t ($34.20 per st) in the fourth quarter of 1985. Coal consumption at coke plants continue to reflect a depressed steel industry. After rebounding 18.9% in 1984 for the first time in five years, coal consumption at coke plants again declined 6.7% to 37 Mt (41.1 million st) in 1985. Coke consumption 26.5 Mt (29.3 million st) exceeded production, 26 Mt (28.7 million st), in 1985. This resulted in a 1-Mt (1.2-million st) decline in coke stocks at producer and distributor levels during the year. The average price of coal delivered to coke plants decreased 7.6% from $64.30/t ($58.34 per st) during the final quarter of 1984 to $59.42/t (53.91 per st) in the last quarter of 1985. Coal consumption in other industries, including all manufacturing and industrial consumers except coke plants, totaled 68.3 Mt (75.3 million st) in 1985. This was the highest level attained in more than a decade. But the lower percentage rise last year (2.1% compared to 11.8% in 1984) reflected slower growth in the nation's economy in 1985. The average price of coal delivered to industrial firms declined 4.5% from $42.32/t ($38.39 per st) in the fourth quarter of 1984 to $40.39/t ($36.65 per st) in the last quarter of 1985. Coal-producing states in Appalachia mined 9.8 Mt (10.8 million st) tons less in 1985 than in 1984 for a 2.4% loss. The largest contributors to the region's production decrease to 393 Mt (433 million st) were Pennsylvania, down 14.7% to 60 Mt (66 million st); Ohio, down 8.3% to 32.6 Mt (36 million st); and West Virginia, down 2.9% to 115 Mt (127 million st). Conversely, eastern Kentucky production was up 4.8% to 111 Mt (122.8 million st) in 1985, while production in Tennessee climbed 9.7% to 40 Mt (44 million st). No coal was mined in Georgia last year. Coal production in the interior region in 1985 declined 3.9% to 173 Mt (190.4 million st). Substantial production losses occurred in Indiana, down 8% to 31 Mt (34.5 million st); and in western Kentucky, down 7.9% to 36 Mt (40 million st). Coal production in Texas rose 5.7% to 39 Mt (43.5 million st) in 1985. Louisiana began mining lignite 140 kt (151,000 st) during the year. Production in the western region increased 3.4% to 238 Mt (262.5 million st) in 1985. Wyoming, up 5.3% to 125 Mt (140 million st); and North Dakota, up 16.5% to 23.5 Mt (26 million st) contributing the largest amounts. Production gains were also shown in Washington, Utah and, notably, in Alaska where coal output climbed 72.9% to 1.3 Mt (1.5 million st) in 1985. Most of the additional coal produced in Alaska last year was shipped abroad. Coal stocks held by consumers totaled 154 Mt (170 million st) at the end of the year. This was 27 Mt (30 million st), or 13.7% below the inventory level at the end of 1984. Stocks held by producers and distributors declined by 868 kt (957,000 st), or 2.8% in 1985 to 30 Mt (33 million st). A drawdown in stockpiles occurred in each consumer sector during 1985. Stocks held by electric utilities totaled 142 Mt (156 million st) at the year's end, 13% lower than stock levels at the end of 1984.

Jan 5, 1986

By A. L. Wilder, S. N. Dixon

Introduction Coeur d'Alene Mines Corp.'s largest precious metals property is located in the historic Rochester Mining District 40 km (25 miles) northeast of Lovelock, NV. The property encountered cold weather operational problems soon after its fall start-up in 1986 due to its elevation of over 1830 m (6000 ft). The problem of ice buildup on the heaps because of sprayed solution application was faced immediately. It was felt that allowing ice to build up all winter long until a spring thaw was impractical due to the large area under leach. Further, the operating cost and delivery schedule for a solution heating system was unacceptable. The development and installation of a leach solution distribution system using drip emitters made efficient, cost-effective winter operation possible. Other benefits of this system have also been observed and are discussed here. General process description 15,422 kt/day (17,000 stpd) of - 1.27-cm (-1 /2-in) crushed ore from the three-stage crushing plant are delivered to the leach pad using 77.1 t (85 st) rear dump haul trucks. The ore is drifted into place with a D-9 bulldozer. Leach panels are contiguous and are approximately 8861 m'(90,000 square ft) in area built in 6-m (20-ft) lifts. New panels are built on top of older areas to a final height of 61 m (200 ft). Each panel is ripped and cross-ripped prior to leaching. Barren solution is distributed to the heap using drip emitters at rates of 0.02 to 0.41 L/min/m2 (0.0005 to 0.01 gpm per sq ft), depending on the age of the panels. The pH of the leach solution is 10.7 with a cyanide concentration of 0.75 kg/t (1.5 lb per st). Approximately 50% of the silver and 80% of the gold are finally recovered. Pregnant solution percolates though the heap and flows by gravity into one of two 9.46 ML (2.5 million gal) pregnant solution ponds. The solution is then pumped to a conventional Merrill-Crowe process plant. Clarification takes place in three 9464 L/min (2,500 gpm) capacity filters. The solution is then pumped to a packed vacuum deareation tower for the removal of dissolved oxygen. Typical deareated solution contains 0.7 parts per million dissolved oxygen. Precipitation of gold and silver is accomplished by adding a zinc dust slurry to the deareated solution at the suction of the filter press feed pump. Precipitated gold and silver are recovered in three recessed plate and frame filter presses. Barren solution is discharged into a 11.7 ML (3.1 million gal) pond where cyanide makeup occurs. This solution is pumped back to the heap for further leaching. The precipitate filter cake, containing approximately 75% dore (Ag + Au), is then fluxed with anhydrous borax, soda ash, sodium nitrate and fluorspar to yield a neutral, bisilicate slag. The fluxed precipitate is then charged into a propane-fired melting furnace and heated to 1150° C (2100° F) for 3 1/2 hours. Slag and dore bullion are poured into conical cast iron pots yielding buttons of 800 to 1000 troy oz. The dore typically contains 98.5% silver and 1 % gold. Slag is crushed and tabled to recover the trapped dore blebs and beads. Concentrate from the table is returned to the furnace. Table tails are sent to the crushing circuit and out to the leach pad. Solution application The area kept under leach at Rochester is approximately 130 000 m2 (1.4 million sq ft). Barren solution is delivered to the pad at 21.2 kL/min (5600 gpm) for a resultant application rate of 0.16 L/min/m2 (0.004 gpm per sq ft). A traditional solution sprinkling system using No. 12 Senninger Wobblers with individual pressure regulators was installed at the onset of leaching activities. The Wobblers were placed at 9.1-m (30¬ft) staggered centers and were fed off of a gridwork of Yellowmine plastic piping. Solution flow rates were moni¬tored to each panel. The onset of cold weather with an average nighttime temperature of -12° C (10° F) made it apparent that continual operation would not be possible with the sprinklers. A significant amount of ice was built up on top of the heap, making maintenance and pipe removal dangerous, if not impossible. Leach solution application was restricted to daylight hours to inhibit ice formation. Process plant flow rates were reduced to maintain steady-state operating conditions. However, as daylight temperatures dropped below freezing, ice continued to accumulate due to the sprays. Besides the obvious operating hazards brought on by the growing icefield, there was also the potential environmental hazard associated with an early thaw melting the ice too rapidly for the solution containment facilities. One other option for preventing ice formation was heating of the barren solution prior to spraying. Initial plant design allowed for expansion of the propane storage and distribution system as well as modification of the barren piping for a solution heater. This option was not exercised because the operating costs for an adequate system would have been prohibitive, and timely delivery of a system was not available. An investigation was conducted on the various drip irriga¬tion products available, since subsurface solution applicators would eliminate ice formation altogether. Systems utilizing external flow emitters were ruled out because of their ten¬dency to clog when buried. Emitter systems using perforated tubing were also eliminated from consideration due to their inability to adequately control flow over required lengths of tubing. An in-line emitter system was finally selected which demonstrated clog resistance and adequate flow control, enabling direct burial.

Jan 1, 1990

By H. Wagner

INTRODUCTION One of the most important tasks facing the opera¬tors of deep-level gold mines is supporting the roof strata in the immediate vicinity of the stope faces. Some of the deeper gold mines operate at depths ex¬ceeding 3.0 km; the extreme mining depths and the tabular nature of the gold-bearing reefs result in high stress concentrations at the abutments of the stope faces. These, in turn, lead to extensive fracturing of even the hardest quartzites. Although most of these fractures develop in a stable manner, there have been many instances where rock failure occurred suddenly, resulting in a considerable amount of damage to the underground workings. Such violent rock failures commonly are known as "rock bursts," and they are typical of many hard-rock mines that are operating at great depths. To safeguard mining personnel and equipment against the effects of stable and unstable rock failures, adequate support must be provided to the fractured roof as quickly and as effec¬tively as possible. Traditionally, timber props and timber packs have been utilized to provide roof support in gold mine stopes up to 1.5 m wide. Both methods of support suffer from the fundamental disadvantage of generating sup¬port only in reaction to movement of the strata. Since unrestrained strata movement often results in a break¬down of the frictional forces that preserve the stability of the intensely fractured roof strata, it is essential that stope supports have rapid load-bearing characteristics. An equally important requirement is that the roof sup¬ports be able to accommodate displacements of the rock mass. A third requirement of roof supports in gold mine stopes is that they must be able to accommodate the high rates of stope convergence typical of rock bursts. The hydraulic prop is the obvious choice for sup¬porting the stope faces in deep-level hard-rock mines. Since hydraulic props can be installed with a positive setting load, they can provide roof support that is independent of strata movement. By equipping the hydraulic props with yield valves, they meet the require¬ment of being able to accommodate rock-mass displace¬ments. However, the requirement of being able to accommodate high rates of stope convergence without overloading or damaging the rock strata was rather difficult to meet. The first introduction of hydraulic roof supports into gold mine stopes showed that conventional hy¬draulic props, such as those used in coal mines, were completely unsuitable for a number of reasons, in¬cluding: 1) Since drilling and blasting are used to break the ore in gold mine stopes, supports installed close enough to be effective are exposed to the vigor of the blast. Conventional coal-mining props suffered extensive blast damage, despite being protected by a blast barricade. 2) The environmental conditions in gold mine stopes favor corrosion. The high quartz content and the abrasiveness of the ore further aggravate the problem by damaging the protective coatings on the hydraulic surfaces. Simply changing the design of gold mine props to have the piston project from the bottom rather than from the top resulted in dramatic improvements in the service life of the props. The improvement was attributable to external water in the stope washing the fine quartz grit away from the hydraulic surfaces, rather than concentrating the particles between the cylinder and piston of the prop. 3) The most obvious deficiency of conventional coal mining props was their inability to yield rapidly enough to accommodate the high convergence rates of rock bursts without overloading the supports. As a result of the first disappointing results with hydraulic supports in narrow hard-rock stopes mined by drilling and blasting, a comprehensive research and development program was undertaken. The hydraulic props resulting from several years of research and exten¬sive field trials are described herein. To date (1978), more than 130,000 of these props have been manufac¬tured and used successfully in a number of mines and under a variety of geological conditions. Although many of the detailed specifications are directed spe¬cifically to gold mining conditions, there are a number of points that are of general importance in the design of underground support systems for tabular excavations in hard-rock mines of any type. SPECIFICATIONS FOR RAPID-YIELDING PROPS Yield Requirements The yield requirements for hydraulic props in deep¬level hard-rock gold mines are summarized in the fol¬lowing paragraphs. Slow Yield Load: The design of the yield valve must allow the yield load to be preset to between 300 and 400 kN. This flexibility is necessary to account for the differences in the strength properties of the roof and floor strata. Drop in Load Under Slow Yield: The drop in sup¬port load during a slow yield should be as small as possible, but it should not exceed 5% of the slow-yield load. Rapid-Yield Load: The load exerted by the prop during periods of rapid stope convergence should be as close as possible to the slow-yield load. The rapid-yield load should not exceed the slow-yield load by more than 15% at yield rates of 1.0 m/s. The limitation of the upper valve of the yield load is important; it deter¬mines the hydraulic performance of the yield valve. The hydraulic props that satisfy this criterion have performed well, even under severe rock bursts. Load Changes Under Rapid Load: On some of the earlier rapid-yielding props, conditions of dynamic in¬stability were observed; these conditions resulted in a complete breakdown of support resistance. It is essen¬tial that the force oscillations during rapid yielding be as small as possible, not exceeding -*5% of the average rapid-yield load at a yield rate of 1.0 m/s. Longitudinal Resilience: During rock bursts, vibra¬tions of the roof and floor sometimes are observed. To

Jan 1, 1982

By Lawrence Williamson, Randall J. Essex, David P. Field

As part of a $2.2 Billion bridge project that will link Indiana and Kentucky, an interchange project northeast of Louisville will require the mining of a 6-lane tunnel system about 2,000 ft long in order to cross beneath the historic Drumanard Estate. This paper will discuss preliminary engineering that has been undertaken to compare two-bore and three-bore layouts, the planning of an exploratory tunnel facility, and the potential for including a test chamber to investigate the ability of high capacity roadheaders to mine the 22,000 psi limestones.

Jan 1, 2005

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin, Derek Maishman

Ground freezing was utilized to provide complete stability of the excavation face and complete groundwater cut-off for the jacking of the three tunnel boxes for the Interstate 90 / Interstate 93 approach to the Fort Point Channel crossing. Through a wide range of geological conditions and large buried obstructions, the freezing provided complete stability of the face so that a 11.5 m (38 ft) high free standing vertical face could be mined without the need for any additional face support. Obstructions were incorporated into the massive frozen ground matrix, and held in place so that they could be excavated with a minimum of disturbance. The freezing provided an absolute groundwater cut-off, and permitted the work to be done without disturbance to the active rail system immediately above. With the use of instrumentation such as borehole thermocouples, the effectiveness of the freezing was guaranteed and the jacking proceeded with complete confidence and assurance of the ground conditions ahead.

Jan 1, 2001

By Andy Mille

The paper highlights development of tunneling methodology in the UK during the years 1990-2000 using the example of two major tunneling contracts where there solution of difficult tunneling problems during construction has benefited the industry as a whole. The paper deals with specific difficulties on two Contracts. The London Water Ring Main 80 kms (50 miles) long tunnel average internal diameter 2.54 m (9 ft4 in) and the Brighton Stormwater Tunnel 5.2 km (3.2 miles) long tunnel with an internal diameter of 6 m (19 ft 8 in). The results of human endeavour and technological innovations will demonstrate the giant strides made in tunneling methodology in the last decade of the 20th Century.

Jan 1, 2001

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By V. B. Achanti, A. W. Khair

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be: bit spacing, bit geometry, depth of cut and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Tree bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 900. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Restorable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Feb 24, 1997

By S. Frimpong

Cable shovels are used for primary excavation in in-situ and/or pre-fragmented formations in surface mining operations. Poorly fragmented hard rock formations and random occurrence of hard boulders in soft formations cause extreme variability of material diggability, resulting in varying shovel stress loading. The stress loading of a shovel’s front-end assembly could result in fatigue failure. Conventional design process, which uses physical shovel simulation studies, is very costly and time consuming for achieving statistically significant results. In this paper, rigid and flexible multi-body dynamic theories are used to develop component stress loading and deformation models of the cable shovel, and solved in the ADAMS/NASTRAN/FLEX environments. Detailed simulation experiments are carried out to examine the performance, reliability, durability and efficiency of the P&H 4100A under varying in-situ formation conditions. The results show areas of high stress fields with a maximum stress of 313.31 MPa at node 441 within the hoist rope. The reliability of the results is confirmed by comparing existing test data. The study is significant because it provides a solid foundation for further study of failure life analysis of the cable shovel components.

Jan 1, 2007

By J. Jonas, J. M. Harrington, K. Wangerud, S. D. Fundingsland, J. G. Harrington

EPA NRMRL Mine Waste Technology Program and Region VIII Superfund office are jointly conducting an in-situ technology demonstration at the Anchor Hill Pit Lake, Gilt Edge Mine Superfund site. The goal is to develop in-situ treatment cost/performance data for potential application in long-term water treatment/management at Gilt Edge and similar sites. The pit contained 77,000,000 gallons of pH 3water with elevated metals, sulfate, and nitrate. The Green World Science® patented process for in situ treatment was implemented to isolate and sequester metals; create stable long-term water quality and restore a sustainable ecosystem. COCs have decreased more than 99%, and dissolved discharge standards were attained.

Jan 1, 2004

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By Val E. Payne

Issues between resource utilization and resource preservation often develop in connection with coal mining. One such conflict exists in eastern Utah where PacifiCorp and Energy West Mining Company are working with State and Federal agencies to address the resource recovery/resource preservation dispute. The effects of underground longwall coal mining on golden eagle (Aquila chrysaetos) cliff nesting sites have been studied at the Cottonwood Mine since 1986. Subsidence, escarpment spalling, and the nesting activities of the local eagle population were monitored.

Jan 1, 1986

In 1992, the United States economy grew at a rate of 2%. The Gross Domestic Product rose to $5,946 billion. With 257 million people - 635,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose I 1 % to 1.2 million units. New car production rose 4% to 5.7 million units. Truck and bus production rose 20% to 4 million units. The rate of inflation was 3.5% and the prime rate of interest was 6.25%. The Producer Price Index (1982 =100) was relatively unchanged from 1991 as follows: fuels and related products and power 80, metals and metal products 119, chemicals and allied products 126 and nonmetallic mineral products 117. Energy Imports of crude and refined petroleum, costing $50 billion, rose 3% to 455 Mm3 (2.9 billion bbl). Domestic petroleum production fell 1 % to 582 Mm3 (3.5 billion bbl). Petroleum supplied about 41 % of US energy, natural gas 24% and coal 23%. Coal production, 60% from surface operations, rose 1 % to 914 Mt (1 billion st). About 78% was used to generate electricity and 3% was coked. Exports valued at $4 billion included 57 Mt (63 million st) of metallurgical coal and 39 Mt (43 million st) of steam coal. Ura¬nium mining, including recovery from phosphates, fell 18% to 3 kt (3300 st) U308.

Jan 1, 1993

By Chris Bennett, Drupad Desai, Kirit Mevawala

INTRODUCTION The design/build (D/B) philosophy of contract delivery is neither new nor unusual when it comes to at-grade, elevated or high-rise structures. But when it comes to constructing underground facilities, there were no examples to be followed in early 90sin the continental United States or its territories. When DMJM+HARRIS was selected as general architectural and engineering consultant for the Tren Urbano (TU) project in Puerto Rico, one of the requirements of the Federal Transit Administration (FTA) for funding commitment was to use TU as a demonstration project utilizing design/build contract delivery method. Now fifteen years later, New York City Transit (NYCT) has instituted a similar requirement for their first Tunnel Boring Machine (TBM) contract for the Second Avenue Subway. As with most construction mega-projects, lots of things have happened and there were several lessons learned from the TU experience that are now being applied to Second Avenue. Both of these projects require building tunnels and underground transit facilities in heavily traveled corridors of an urban city, in the vicinity of active business and commercial enterprises. To enhance the challenge, there are noise and vibration sensitive and historic urban receptors either over or along both the transit corridors. Column free Tren Urbano station caverns over18 m (60 ft.) wide were built in soft ground conditions within 3.6 m (12 ft.) of the surface under an aging heavy utility corridor, while NYCT tunnels with station structures stretching the limits of rock caverns to 34.8 m (100 ft.), were planned in rocky geology with the presence of shear and fault zones and some mixed face conditions. BACKGROUND During the early period of design/build experimentation, the speed with which the contract procurement packages could be put together enabled the owners to take advantage of the major efforts underway to rebuild the infrastructure that was suffering from post-World War II neglect. Use of design/build for new starts was unheard of and most of the projects were smaller in nature in order to allow the methodology to be tested. Development of functional design packages with the understanding that the D/B

Jan 1, 2005

By J. D. Morgan

The US economy continued to grow steadily in 1988, reaching an annual rate of $5 trillion in the last quarter (US trillion = 1012). The value of domestically processed mineral-based materi¬als rose 20% to $300 billion (US billion 109). The value of metals produced from US ores rose 40% to more than $10 billion, industrial minerals rose 6%' to $20 billion, and recycled scrap more than doubled to $10 billion. Increasing economic activity stimulated metal prices. Yearly lows and highs were 95 cents and $1.68 for copper, 52 cents, and $1.30 for aluminum, 34 cents and 42 cents for lead, and 43 cents and 75 cents for zinc. A number of mining and metal companies experienced significantly increased profitability. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and Federal debt continued to rise. About 246 million US citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production remained at the 1987 level of 7.1 million units. Truck and bus production, however, rose 7% to 4.1 million units. New housing starts fell 7% to 1.5 million units. Imports supplied a significant proportion of total US consumption of several important mineral materials. By year-end, imports of crude and refined petroleum exceeded domestic crude oil production. Such imports cost $42 billion. Imports of nonfuel mineral-based materials were valued at $44 billion and exports at $35 billion. The US and Canada-the world's two largest trading partners-consummated a historic free trade agreement. In February, President Reagan transferred responsibility for stockpiling strategic and critical materials to the Secretary of Defense. And, in July, the GSA group that bought, stored, rotated, and sold stockpiled materials was transferred to the Defense Department's Defense Logistics Agency. Concern about apartheid in South Africa continued, resulting in increasing attention to chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve, was amended to include provisions for averting harm to national security from foreign takeovers. The DPAct, in effect through September 1989, is now up for further extension. Under the Act, the US Bureau of Mines maintains the Emergency Minerals Administration. During the year, consultations were held with Canada to strengthen the North American Defense Industrial Base. Coal production, 60% from open pits, rose 5% to 870 Mt (960 million st). Nearly four-fifths was burned to generate 57% of US electricity. Exports included 56 Mt (62 million st) of metallur- gical coal and 29 Mt (32 million st) of steam coal, with a total value of $4 billion. Domestic petroleum produc¬tion fell 2% to 574 hm3 (3.6 billion bbl). Uranium mining, including recovery from phosphates, was unchanged at 5.9 kt (6500 st). Nonfuel minerals Major metals Raw steel production-a major con¬sumer of many minerals-rose 14% to 92 Mt (102 million st). Domestic iron ore production rose 25% to 59 Mt (65 million st), about 96% pelletized. Net imports rose 37% to 16 Mt (18 million st). Raw steelmaking capacity of 102 Mt (112 million st) was unchanged. Voluntary Restraint Agreements with 21 steel exporting nations limited im¬port penetration to about 20% of the domestic market. Domestic producers of bulk ferroal¬loys of chromium, manganese, and sili¬con operated at about 75% of capacity. The US mined no manganese or chro-

Jan 1, 1989