Search Documents

By Paul D. Tomlingson

Part two of this two-part series covers the use of an integrated information system with administrative information, including error and absentee reports as well as open work files. Part one (ME, July, page 650) discussed conceptualizing and developing a maintenance information system. It explained what information is needed to manage such a system.

Jan 8, 1985

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6)tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of a longwall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

Jan 1, 2000

By Peter G. Sechiari

The Rio Tinto-Zinc Corporation Limited (RTZ), through it exploration company Riofinex, commenced exploration for bauxite in the Amazonia region of Brazil during 1970. Following' encouraging indications, exploration licences were taken out and an exploration programme was initiated In February 1975, a preliminary 'feasibility report indicated that a project, based on the Miltonia plateau located close to the town of Paragominas in the State of Para, was viable and that barging might offer an economic solution to getting the product to an ocean-going port. A, decision was taken in April 1975 to proceed with a full feasibility study. In the latter stages of the study, an engineering consortium of Mendes Junior and Bechtel do Brasil was employed to review, and modify if necessary, the concepts that RTZ had developed for the project's operation. With these concepts agreed, the consortium was requested to make capital and operating cost estimates, and these became available during February 1978. The deposit is being developed by a Brazilian company Mineracao Vera Cruz S.A. (MVC) in which the present share-holding is owned 64 percent by RTZ and 36 percent by Companhia Vale do Rio Doce (CVRD). RTZ is a British based international group of mining and industrial companies with interests in almost every major metal and fuel. CVRD is a Brazilian mining company, 85 percent owned by the Brazilian Government, with a major interest in iron ore and also other non-ferrous metals. It is intended, in due course, that the company will become majority owned by Brazilian interests.

Jan 1, 1979

By F. Habashi

The changes that took place in China between 1984 and 2004 are remarkable. Visits were made to universities, research institutes, metallurgical industry, and many cultural centers within five trips during this twenty years period. The impressions of these visits are outlined.

Jan 1, 2007

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

By T. Brozell

"Communities near sand mines and processing facilities in Wisconsin have raised concerns regarding possible exposure to ambient respirable (PM4) crystalline silica. Fenceline PM4 (particulate matter captured with a 50 percent cut size of 4 micrometers aerodynamic diameter) crystalline silica concentration data were compiled at Fairmount Santrol Inc., Mathy Construction Inc. and U.S. Silica facilities. The long-term average PM4 crystalline silica concentrations ranged from 0.05 to 0.45 micrograms/m3 when sample values below the limit of quantification were treated as zeros. All of the long-term average concentrations were less than 20 percent of the Minnesota Department of Health’s and California Office of Environmental Health Hazard Assessment’s PM4 crystalline silica chronic reference exposure level of 3.0 micrograms/m3. The measured concentrations were consistently within the local background concentration range.Air Control Techniques P.C. compiled the sampling data using Thermo Fisher Scientific Inc. Partisol 2000i PM2.5 samplers meeting the requirements of 40 CFR Part 50, Appendix L. These samplers were adapted to capture particulate matter with a 50 percent cut size of 4 micrometers. The use of polyvinyl chloride filters allowed for crystalline silica X-ray diffraction analysis by NIOSH Method 7500. The combined use of adjusted PM2.5 filter-based samplers with Method 7500 crystalline silica analyses provided for a highly sensitive limit of quantification of 0.31 micrograms/m3 of PM4 crystalline silica.BackgroundIn 2005, the California Office of Environmental Health Hazard Assessment (OEHHA, 2005) adopted a 70-year chronic reference exposure level (REL) for PM4 (particulate matter having aerodynamic diameter of 4 micrometers or less) crystalline silica. The REL was extrapolated from occupational hygiene epidemiological studies, essentially all of which were based on in-plant PM4 crystalline silica measurements. No well-established ambient sampling technique for PM4 crystalline silica was available at the time that OEHHA adopted its REL. The personal samplers used for the National Institute for Occupational Safety and Health (NIOSH) Method 0600 in-plant sampling of employee exposure were designed for concentrations higher than ambient levels. The limit of quantification (LOQ) of PM4 crystalline silica on NIOSH 0600 filters was too high for the effective sampling of ambient air."

Jan 1, 2015

By S. I. Freedman

Coal-oil mixture (COM) combustion technology is regarded by the Department of Energy as near term, and potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers, into blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally-acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1978

By Dr. Jack M. Gillette

A system of models which simulate surface coal mining operations has been developed for use in mine planning and economic evaluations. Micromodels simulate individual mine operations for equipment selection and mine planning. Macromodels simulate all operations in the complete mine for economic evaluation of reserves. A cash flow analysis model makes a complete discounted cash flow analysis to deter-mine a required coal sales price or return on investment for evaluation of any mining project.

Jan 1, 1978

By James N. Orlich

Meridian Gold Company's Royal Mt. King mine (RMK), a subsidiary of FMC Gold Company, is located approximately 40 miles east of Stockton, California on the western edge of the historic mother lode belt. Gold ore at RMK is associated with a series of northwest trending fault zones hosted in either meta-volcanic or meta-sedimentary rock types commonly referred to as greenstone sulfide and carbonaceous phyllite. Mineralogy studies show gold in both ore types to occur primarily as electrum in the form of 1 -20 um inclusions in pyrite with varying amounts of free milling gold. In carbonaceous ores, gold was not found to be closely associated with carbon. At the start of the current mining operation, three major ore resources were identified. North Pit and Gold Knoll pits were the major greenstone reserves while Skyrocket Pit contained over 60% of the total reserves as carbonaceous ore. Since North Pit and Gold Knoll were to be the first areas mined, the mill began operation in February 1989 with a flowsheet designed for greenstone ores with a carbonaceous expansion anticipated after depletion of the greenstone reserves.

Jan 1, 1992

By D. M. Davidson

The economics of geologic exploration have changed materially in the past decade primarily due to the change in three basic factors, namely, increased wages and salaries, increased cost of materials, and a greater complexity in methods of exploration. Following the general economic pattern over the past ten years, exploration costs, have, in general, increased, although there is one heartening exception. A comparative picture is complicated because of advances in techniques which ensue from the introduction of new methods and devices largely for aerial exploratory work, Some of these methods were either in their infancy or unknown before World War II. Geological exploration may well be considered as a form of applied research. True, it has peculiarities from this standpoint some advantageous, others disadvantageous, Some of the advantages lie in the fact that exploration success does not involve the production of a new product which necessitates advertising expense and marketing problems. In normal times there is a well established market for the fruits of a successful mineral find. The outstanding disadvantage of exploration lies in the enigma of deciding when to quit if the sought fop prize is elusive. In the search for buried treasure, man?s curiosity is apt to color his judgment. Even the so-called detached scientist may fall 'all too readily into the wishful thinking of the old- time prospector who is lured on by the thought that the next pull from the drill hole, or the next round from the face will reveal a bonanza. It involves mature judgment and experience to ascertain the stage in exploration when further work is not justified.

Jan 1, 1958

By Praterm J. D.

The process parameters for effective utilization of nitric acid as an oxidant for copper-iron sulfides have been developed. Leaching variables found to be important were acid concentration, temperature, time, atmosphere, pressure, mineral type, particle size, and percent solids. Particular attention was devoted to analysis and control of fumes evolved during the oxidation. Responses recorded were metal extraction, elemental sulfur formation and oxidation, product gas composition and evolution rate, reagent consumption, and residue flotation response. The paper concludes by laboratory testing a flow sheet based on the above observations. Ninety-eight percent of the copper contained in a chalcopyrite-bornite concentrate was recovered, requiring 1. 6 pounds of nitric acid to be regenerated externally per pound of copper extracted. Iron remained in the leach residue as hydrogen jarosite and was ultimately rejected from the system by froth flotation. Sixty percent of the sulfur contained, in the heading concentrate reported in the elemental form; the remainder was oxidized to sulfate and eliminated with the hydrogen jarosite in the flotation tails or by neutralization of the solvent extraction raffinate with lime. Nitrogen was evolved primarily as NO and NO2; up to 3 percent N2O was also present. Gases containing sulfur were absent except when pyrrhotite was solubilized in the absence of soluble copper. In this case, H2S was evolved.

Jan 1, 1972

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By Rory P. A. Ball, Mark Briggs, Martin Dix

"Tunnel professionals should inform project stakeholders on the reality that tunnel projects are not 100 percent devoid of the need for excavations or public inconveniences during both design and construction phases. Competing stakeholder objectives to limit these disruptions must be weighed against the need to mitigate risks and to produce a constructible, operable and maintainable end product. Perhaps the approach we should take with stakeholders, also known as Authorities Having Jurisdiction (AHJs), is sharing memorable case studies that bring to life the potential risks so often buried within lengthy risk registers. This paper provides a sobering case study describing what can occur if the presence and/or location of utilities and other obstructions are not fully understood due to restrictions placed on exploration or mining operations. In this instance, the Microtunnel Tunnel Boring Machine (MTBM) encountered a buried concrete structure, followed by rows of abandoned wood piles, before finally colliding with an active high-pressure gas main under a bustling coastal highway. Multiple stakeholders imposed tight logistical and other work restrictions, compounding the difficulties experienced during the drive. However, the difficulties were effectively managed through the project team’s proactive collaboration and communication with everyone involved. INTRODUCTION Some of the most important decisions that influence the ultimate success or failure of a project may not be made by design engineers. Instead, these decisions are often made by project stakeholders and third-party agencies. Tasked with protecting the best interests of their users, these agencies are cautious of potential impacts associated with project construction and subsequent use. Unfortunately, actions required (or restricted) by stakeholders often result in unwanted ripple effects that negatively affect the very users they are trying to protect. For example, a mandate limiting a shaft site to an unreasonable size may be intended to reduce local business impacts, but may actually increase impacts as more supply and truck hauling is required."

Jan 1, 2016

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By D. C. Torre

The need for a successful, efficient and reliable continuous face- haulage .system for use with continuous mining machines has been apparent since the first continuous miners were introduced some twenty-five years ago. Some thought and effort were given to the development of continuous haulage over the last twenty years or so. Some initial success was experienced in this area by The Long Company with a system involving bridge conveyors, as far back as the late 1950's. However, extensive success with continuous face haulage for use behind modern, high product¬ion, continuous miners escaped the industry until the early 1970's. It is true that continuous face haulage was successfully introduced into low seam mining, generally in seams ranging under 1.07 m (42") in height, in the 1960's, for use with relatively low production, low seam, auger type continuous miners. However, those available systems which have achieved success in the lower seams, where relatively low capacities are adequate, are not directly applicable for use with today's medium and high seam miners with their standard production capacity of 9.1 - 10.9 mtpm (10 - 12 tpm). Since the late 1960's and early 1970's, several machinery manufacturers, and at least two major coal companies, have devoted considerable expense, time and effort to developing truly successful continuous face haulage for use in coal seams ranging upward from 1.2 m (4') in height. Continuous face haulage equipment has been developed in the last five years employing a variety of transportation media and design concepts, including some which have received wide publicity such as those employing hydraulics, and pleated belt. The truth of the matter is, however, that the only universally applicable and widely successful continuous face haulage equipment introduced to date has been that employing a combination of bridge conveyors and mobile, self-propelled, bridge carriers, connected at the inby end to the tail of the high production continuous miner, and at the outby end attached directly to the panel conveyor (Fig. 1 & Fig. 2) or, on occasion, to a short, self-contained conveyor which, in turn, empties directly onto the panel conveyor. While these bridge type continuous haulage systems are available with both belt and chain conveyor components, the most widely applied and successful system in seams above 1.07 m (42") in height is that offered by The Long-Airdox Company. The standard unit for use with 9.1 - 10.9 mtpm (10 - 12 tpm) continuous miners is normally equipped with belt. However, they have built, and successfully applied, versions of this system employing chain conveyors, (Fig. 3), mainly for operators having extremely difficult mining conditions, including excessive amounts of water

Jan 1, 1977

By M. Noppé

"Dilution in underground coal operations can be underestimated by up to five times during Feasibility Studies, with disastrous economic consequences. Every 1% of stone waste introduced can reduce an in situ specific energy of 11,000 BTU/lb (25 MJ/kg) by some 110 BTU/lb (0.25 MJ/kg) and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some AU$1 million per year.This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation. The dilution trends before and after introducing the recommended controls in a continuous miner/longwall mine are presented over an eight year period. The additional information from such a dilution monitoring program can also be used to control mining horizons and plan longwall extraction heights across the face proactively, on a short-term scale with resulting improvements in productivity. INTRODUCTION Grade control, as practiced on any mine, is concerned with predicting routine quality and tonnage values for short- to medium-term mining operations, and the reconciliation of these predictions against “actual” results. For a longwall mine supplying steam coal, such routine parameters may include the proximate analyses, specific energy (SE), abrasiveness and sulphur, as well as float and sink analyses if the coal is beneficiated. In addition, grade control is concerned with identifying the mineable horizon (or horizons) in a selective-mining operation, together with monitoring how well these horizons have been extracted or adhered to. Close-spaced surface drilling can be costly for any mining venture, particularly for longwall mines operating in the deeper seams. For this reason, much of the data for short-term grade control requirements are acquired during actual bord-and-pillar development. The underground data are derived from so-called “channel” samples. These samples are cut or chipped from the coal seam, perpendicular to the mining horizon, with dimensions suitable for obtaining sufficient “representative” sample for analyses. For a 2m thick mining horizon, a channel sample 300 mm wide and 50 mm deep over the thickness of the horizon would provide some 4.5 kg of sample, sufficient for most of the necessary tests. To allow the information to be computer recorded, additional information such as seam thickness, sample co-ordinates, and the elevation of the seam (or horizon) roof or floor, may be required."

Jan 1, 2015

By E. M. Williams

The U.S. Bureau of Mines recently conducted a limited-scope study on the use of lineament analysis and electromagnetic geophysics to better identify the surface expressions of faults at the Cimmaron Mine near Raton, NM, an operating longwall mine in the York Canyon mine complex. Two normal faults were encountered by the mine, one during gate road development and drilling and another only through drilling. The potential ground control problems and offsets associated with these faults will severely impact long-range development plans, so it is essential to know the lateral extent of these faults within the coal reserves. The surface topography at the site is fairly rugged, yet outcrop exposure is poor. There is no obvious visible geologic evidence to indicate that the faults identified at depth extend to the surface. Both the geophysical and remote sensing techniques provided information on the presence and extent of important geologic structures which could not be gained just from drilling and surface outcrops. The geophysical surveys also were invaluable in confirming the presence of subsurface geologic structures in the vicinity of the lineaments assumed to be associated with the faulting.

Jan 1, 1995

By R. C. Berry

The Environmental Impact Statement (EIS) has become a routine requirement for mining operations on federal lands. A similar document is being required in developing countries. Baseline studies are needed prior to writing an EIS and these studies involve surface water, groundwater, air quality, and wildlife/ native plant evaluations. The required baseline hydrology and geochemical studies are often the most expensive and lengthy evaluations. This paper summarizes the hydrology and geochemical baseline studies required for .An EIS and presents suggested methods to expedite these studies and to shorten the time and the cost to complete the studies and the EIS.

Jan 1, 1999

By Dr. Ing. Hermann Boldt

The Bituminous Coal Mining Industry of the Federal Republic of Germany produces nearly 100 million t/yr of clean coal. The largest coal mining area is the Ruhr District with dimensions of 100 x 40 km (65 x 25 miles). Figure 1: Here is the general administration of Ruhrkohle Akteingesellschaft RAG with its three divisions. Other coal mining areas in Germany are the Saar District and the Aachen District. Ruhrkohle produces 70 million t/yr of clean coal. The company operates 28 mines in the Ruhr District with an average raw coal production of 18000 t/day. Their average mining depth is 831 m (2740 ft.) and the average seam thickness is 177 cm (70 in.). Figure 2: Preparation plant reject is 44.6%. All following production figures will be with reference to raw coal because the raw coal production is the technically relevant number. Mining operations are mainly in non-dipping coal deposits whereby mechanized equipment for flat seams is also applied to deposits dipping up to 45? Coal extraction is done exclusively by the longwall method. Approximately 200 longwall installations are in production at any time. The average longwall length is 221 m (730 ft) ranging between 140 and 290 m (460 ft and 960 ft). The average longwall advance of all operations is 2.8 m/day (8.4 ft per day). Average production

Jan 1, 1977

By A. Arik

Reliable ore reserve estimates for deposits with highly skewed grade disributions are difficult tasks to perform. Although some recent geostatistical techniques are available to handle problems with these estimations, ordinary kriging or conventional interpolation methods are still widely used to estimate the ore reserves for such deposits. The estimation results can be very sensitive to the search parameters used during the interpolation of grades with these methods. This paper compares the ore reserve estimates from ordinary kriging using several cases in which certain search parameters are varied. The comparisons are extended to different mineralizations to show the changing effects of these parameters.

Jan 1, 1990