Search Documents

By W. Collingwood

As open pit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in open pit mines is often recirculatory. This recirculation traps dust and gases in deep open pit mines. This problem is particularly acute in high latitude open pit mines due to a phenomenon known as an atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In open pit mines, this can result in unhealthy accumulations of gases and other contaminants in the open pit mines. In this study, the natural wind flow patterns in and around open pit mines were investigated using a computational fluid dynamics (CFD) program. Two dimensional models were created for a variety of pit geometries. The effect of depth, slope angle, and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2011

By D. Jacobson

There are many different machine setup parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the eccentric speed at which the cone gyrates. In June 2012, pilot tests were conducted on a 200 hp high speed cone crusher to determine the production and operating conditions over a wide spectrum of eccentric speed. Every plant will have variations in the ore characteristics and feed rates throughout the life of the mine, and at times throughout a single shift of operation, which result in non-optimal use of the crushing energy and inconsistent process control. For high speed cone crushers, the crusher will exhibit a different capacity, power required, and discharge size distribution as the speed ranges over the design limits of the machine. This study documents the measured variation in production and energy efficiency both when the crusher was ran at full capacity as well as when the feed to the crusher was not sufficient to run at full capacity. Overall, the results match theory and the capacity and power fluctuated by 25% and 17%, respectively, over the speed range when operated full while there was an overall trend of slightly coarser discharge size distribution as the speed decreased. The results with the fixed feed rate were more telling, as the crushers had 4-14% higher production when making a theoretical minus 12.5 mm product when operating at the optimal speed as compared to the worst speed in the ?typical? speed range for this application. Secondary analysis of the fixed tonnage testing also showed that the power draw was more consistent with lower magnitude spikes at the higher speeds (higher cavity level), as on average the standard deviation of the power draw increased from 7% to 18% and the peak power spikes from 20% to 48% over the speed range tested. The findings lay groundwork for more efficient plant design. Varying the speed of the crusher can be used to tune the crusher speed during commissioning, adapt to changing ore conditions over long periods of time, or be used as a dynamic input into an advanced control system. Each action above would serve to make the crusher(s) more productive and more energy efficient, and would also have mechanical benefits for the machine. Key Words: cone crusher, ore reduction, process control, crushing efficiency

Feb 27, 2013

By S. Watkins, D. Apel, B. Gray, R. Moss

Currently, there are several techniques and technologies available which are used by mining industry in its attempts to remotely monitor the ground movements both at surface and underground mines. The currently available remote distance meters and distance change monitors mainly use phase change and time-of-flight techniques. The described monitor uses triangulation technique to track position of an optical spot projection and then image processing to measure mine wall movements. The system can be easily automated and poses no obstruction to mine traffic. The position of an off-normal laser spot will shift as the target wall moves. The described ground movement monitoring system has potential for superior accuracy and target monitoring can be made through air (gaseous) or other transparent media. The theoretical accuracy and range of this system depends solely on the resolution and focal length of the camera being used. The remote capabilities of the system make it uniquely suited to applications where monitoring is required in high-traffic, inaccessible, or unstable and dangerous areas of a mine.

Jan 1, 2007

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007

By C. C. Clark, P. W. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines were visited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Jan 1, 2002

By D. C. Dahlin, W. K. O’Connor, G. E. Rush, C. A. Summers, S. J. Gerdemann

The Albany Research Center (ARC) conducted studies of mechanical activation by conventional and ultra-fine grinding techniques to enhance olivine reactivity in mineral carbonation reactions. Activated olivine is one of several solid feed materials used at ARC in reactions with carbon dioxide to form carbonate minerals. This paper compares grinding techniques via energy demand data and product characteristics, including particle size distributions, surface areas, full width at half maximum (FWHM) XRD analyses, and particle morphology by SEM analyses. Reactivity was gauged by percent conversion to carbonate in subsequent carbonation tests.

Jan 1, 2004

By J. L. Yordan, J. Kortmeyer, I. Yildirim

Talc is used to remove stickies from pulp during paper recycling processes. It is well known that the interaction is controlled by the surface chemistry at the talc/water, sticky/water and talc/sticky interfaces. If the interfacial tensions are known, one can calculate the free energies of interaction and hence predict whether the stickies can be removed by talc. In the present work, the surface tensions of several different talc samples were determined using the acid/base theory. The information was then used to determine appropriate interfacial tensions, which in turn were used to determine the free energy of interaction between talc and stickies. It was found that the calculated free energies are much more negative than those between the stickies and other minerals such as calcium carbonate, bentonite clay and kaolin clays.

Jan 1, 2002

By M. J. Price

The usage of Geographic Information Systems (GIS) is increasing rapidly throughout the Mining Industry, especially in the Industrial Minerals sector. GIS provides an efficient and robust link between spatial (often CADD) and tabular (database/spreadsheet) components. Mineral economists and corporate planners employ GIS to perform market analyses, to source raw materials, and to schedule and monitor deliveries to customers. Exploration and acquisition groups apply spatial analysis to identify high quality resources that meet economic guidelines. Mining regulators and environmental affairs departments expedite and monitor permitting, environmental compliance, and best management practices reclamation through GIS data management and Electronic Permitting. Operations staffs monitor overburden removal, material extraction, quality control, and stockpile volumes with GIS. This paper summarizes the many aspects of GIS in Industrial Minerals. It also introduces and addresses issues and concerns commonly encountered during a mining GIS implementation.

Jan 1, 2001

By M. J. Lawrence

Independent natural resource Valuers are an essential link between miners and mineral explorers on the one hand and the finance industry on the other. Investors (and regulators) expect the mining and financial industries to be vigilant against the use of inappropriate methodology or use of illogical steps within the chosen valuation method. The Australian Corporations Law generally requires an Independent Expert Report to support mergers and takeovers (as well as for capital raising activities). The introduction of the VALMIN Code (1998) by The Australasian Institute of Mining as Metallurgy, has meant that such Reports, when prepared in compliance with it, are now much more comprehensible and reliable than before. This is because the key requirements of the Code are for transparency and materiality in the Technical Assessment and Valuation Reports prepared in connection with the transaction involved. Transparency is particularly important because it allows the reader to identify and understand the assumptions made to derive a value and to then form a view as to the reasonableness of the result. Even though many elements of resource asset valuation practice are undeniably subjective, there must be some basis of objective rationality to it. Where the reasoning is patently illogical or the inputs are chosen to achieve a particular result, the estimated value must be viewed as virtually worthless. Experience, qualifications, competence and repute are the hallmarks of a professional technical auditor and valuer.

Jan 1, 2000

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled-waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SH) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 4, 1985

By B. R. Benner

Progressive improvements in crusher design, screening efficiency, and operating experience along with the downsizing of many taconite operations has resulted in the abilitv of some crushing plants to produce a substantially finer product. This finer product opens the possibility of replacing the rods in the rod mill with balls as is the current practice at Sydvaranger, Norway. If this replacement could be accomplished substantial savings associated with metal wear and the elimination of rod charging may be realized. The purpose of this study was to compare the performance of a mill charged with rods with the performance of the same mill charged with balls at the pilot scale. The first objective was to establish whether we could achieve the same throughput rate at the same mesh-of-grind in a mill in which the rod media has been replaced by balls. The second point was to determine whether the ball media would create a significant tramp oversize problem.

Jan 1, 1990

By C. G. Clifton

The Oatman District produced approximately 2.2 x 10 6 ounces of gold and 0.8 x 10 ounces of silver between 1897 and 1942. A total of 3.8 x 10 tons of ore averaging 0.58 O/T gold and 0.17 O/T silver was extracted from eight major orebodies and a number of lesser deposits. Oatman lies at the center of a trachyte-latite-rhyolite volcanic complex which contains at least one resurgent caldera. The orebodies are typical epithermal quartz-calcite + adularia lode deposits which are very deficient in sulfur. Ore deposition has occurred within dilatant zones on faults which radiate from a common point within-the complex. Fischer-Watt Mining approached the Oatman District with an integrated exploration program utilizing four basic procedures to define the characteristics of past productive areas the results of which were applied to unexplored portions of the vein system. These procedures, listed in their order of usefulness, in defining known and prospective mineralized zones are: vein contouring, detailed alteration mapping, fluid inclusion temperature determinations, and geochemical sampling.

Jan 1, 1980

By H. Lyn Bourne

This is the fourth annual tabulation that gives mineral royalty information. The table presents previous information plus about two dozen new entries. In addition to the royalty information, some entries show the cost of purchased reserves. Last year's tabulation appeared in two issues, to accommodate all of the information. This year the format has been changed slightly so the table can be printed in one issue. This year's table presents the commodities in the same sequence as last year. Sand and gravel information appears first, followed by: crushed stone for aggregate; other stone; industrial sand; other industrial minerals; energy minerals (coal, oil shale, uranium); and finally metals. As always, a caveat relates to factors that influence the reserve values. The data should serve only as a general reference. The table is not intended to present an absolute scale of reserve costs. Several factors influence the value of mineral commodities. These factors include: • location and transportation costs (especially significant for most industrial minerals); • market conditions for both the commodity and the company acquiring the right to mine it; • quality or grade of the deposit as it reflects the amount of processing and beneficiation necessary to produce the finished product; • and legislative restrictions and conditions for mining a given material at a given site. These and other factors will influence reserve costs of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity; the location (either by state, US geographic area, or Canadian province); the cost (R for royalty and P for purchased cost); and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cuft), tons (/T) (2000 lbs) or acres (/A). 1 cu yd = 0.76m3 1 cu ft =0.28m3 1st = 0.9 t7 1 acre = 0.40 ha or m2 In several cases the royalty is a percentage of the finished products, sale price and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: J. Dunn, T. Eyde, K. Loda, L. Morgan, F. Nix, H. Sorenson, and L. Williams. Several people have said they would like this to be an annual tabulation. That can happen if new information comes to the writer. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write or call: H. L. Bourne, c/o Neyer, Tiseo & Hindo, Ltd., 38955 Hills Tech Dr., Farmington Hills, MI 48018, (313) 553-6300. Only with new information can this become an annual and current source of reserves costs.

Jan 8, 1986

By T. T. Chen

The behavior of gold in a conventional copper electrorefinery anode slimes treatment process is expounded on in this study. In the raw anode slimes generated in a copper electrorefinery, gold occurs mainly as tiny particles of metallic gold, which are commonly attached to selenide particles. Some gold is also present in selenide form. Decopperizing the anode slimes retains much of the metallic gold, but also promotes the incorporation of gold in the structure of silver-rich selenide species. A greater fraction of the gold is converted to (Ag,Au)2Se or Ag3AuSe2 when high-Se and high-Ag anode slimes are decopperized at elevated temperatures and pressures. After pelletization and roasting of the slimes, the gold is converted to a (Ag,Au)-alloy and Ag3AuSe2. Smelting of the roaster products eliminates the selenium and converts the gold to a silver-rich (Ag,Au,Pd)-alloy in the dore metal. In the subsequent silver electrorefining process, gold collects as a gold-rich (Au,Ag,Pd)-alloy in the gold mud. Dore smelting rejects many impurities as a silica slag; minor amounts of gold are present as a (Ag,Au,Pd)-alloy in the silica slag. This gold is recovered by flotation and is recycled to the dore furnace. Gold is identified in both the tellurium caustic leach residue and the parting plant wash water mud as tiny particles of metallic gold. These products are also recycled to the dore furnace to recover their gold values.

Jan 1, 2008

When defining a ?megaproject,? one need only to look at Seattle, WA?s State Route 99 Alaskan Way Viaduct replacement project. This $3.1-billion project is one of the largest of its kind in the world, and includes the use of the world?s largest tunnel boring machine (TBM). However, for as large as the Alaskan Way project is ? especially given the size of the TBM being used ? there are several other megaprojects underway around the world. Each has its own challenges that require innovative design techniques and financing arrangements, as well as variations on established tunneling technologies. So it was that 266 tunneling and underground construction professionals ? owners, contractors and engineers ? convened in Seattle in November for the Cutting Edge Conference on Megaprojects. This was the second joint meeting between the Underground Construction Association of SME and the North American Tunneling Journal. The first joint conference took place in April 2012 in Miami, FL and attracted 238 attendees. A third joint conference, to be held in 2014, is in the planning stage. The key reason Seattle was chosen as the site of the megaprojects conference is the Alaskan Way Viaduct project. Before the conference began, many of the attendees were able to visit the project and get a close look at Bertha, the Hitachi Zosen earth pressure balance TBM that is boring the tunnel. In addition, the conference included an exhibit that attracted 20 industry suppliers, up from 10 the previous year in Miami. The 25 presentations during the two-day conference covered all aspects of the tunneling and underground construction of megaprojects. Topics included the Alaskan Way Viaduct project; considerations for procurement and contracting; political risk, financing and insurance; international megaprojects; risk and risk sharing and project delivery. Each session concluded with panel discussions.

Dec 1, 2013

By Joel S. Leventhal

The roles of organic matter in ore deposits are complex and represent a specialized effort in the larger subject of the geochemistry of ore deposits. The organic carbon cycle can be considered with particular emphasis to ore deposits in order to understand the origin and genesis of the organic matter. Organic matter may play one, several, or none of the following important roles in the formation of ore deposits: leaching, transport, concentration, reduction, and precipitation of metals. For deposits that contain organic matter, detailed field relationships and laboratory characterization of the organic matter are required to make an ore deposit model that Includes the organic matter and specifies its role(s). Examples of the involvement of organic matter in several types of uranium deposits are contrasted as being direct or indirect, syngenetic or epigenetic, and necessary or unnecessary. Examples of organic matter in deposits containing gold and lead-zinc, and In metal rich shale are discussed with respect to ongoing work and critical questions.

Jan 1, 2013

By E. J. Freech

In this part of the two-part paper we discuss briefly the adaptation of the comminution model to describe the observed behavior of an industrial grinding circuit. Although reported verification of comminution models for continuous systems is limited, some interesting work has been reported 1,2 recently. The data acquisition and modeling efforts are described first, followed by discussion of some of the simulation results. Observations pertinent to steady-state operation are presented followed by a description of the application of a dynamic model of the grinding circuit for synthesis and evaluation of grinding-circuit control. The pilot-scale work indicated the comminution model should be capable of describing an industrial size-reduction process. Recognizing the broad utility of a process model based on first- principles, the Industrial Nucleonics Corporation of Columbus, Ohio, embarked on a joint program with the Duval Corporation of Tucson, Arizona, to evaluate the industrial applicability of the models described in Part I. This program was conducted in a grinding circuit, which included a rod mill 12.5 feet in diameter and 16 feet long and a ball mill 12.5 feet in diameter and 14 feet long, at Duval Corporation's Esperanza property3. The rod mill was operated in open circuit and the ball mill in closed circuit with cyclone classifiers.

Jan 1, 1970

By Robert L. Marovelli

The major mining health and safety problems of concern to United States Government and private industry researchers in 1981 included the difficulty experienced by longwall operators in complying with the Federal 2 .0-mg/m3 respirable dust standard, the accident rate associated with falls of ground and materials handling hazards, and the upsurge in the incidence of disasters after the steady decline in recent years. Although the many mines and manufacturing companies involved in the research projects to be described are not specifically identified, it is important to note their significant involvement. This is not by way of acknowledgement, but rather to establish that these projects, using mostly Federal funds, represent close cooperation between the U.S. Government and the mining industry. The ongoing work to be described on the development of critical longwall dust control technology is a classic example of Government-industry participation through the phases of problem identification, planning, cost-sharing, and implement at ion.

Jan 1, 1982

By S. M. Flaherty, R. E. Scheffel, A. Guzman

Geochemical conditions within a leaching operation are heterogeneous. This variability arises mainly from hydrological controls imparted by physical characteristics of the ore and by heterogeneous metallurgical properties at the rock-fragment and industrial heap scale. The resulting chemical conditions are responsible for stratified mineral recovery, non-uniform extraction and prolonged leach cycles. This paper presents field data from a sulfide-leaching operation which clearly demonstrate the impact of chemical heterogeneity on metal recovery and the potential use of modern measuring techniques to facilitate operational monitoring and decision making for optimization of leaching operations.

Jan 1, 2006

By W. McMahon

Following the Sago Mine accident, the Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 1-ft resolution map of the mine to produce a 3-dimensional (3-D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3-D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals, and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling, and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jan 1, 2009