Search Documents

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By Francisco A. Fonseca

The Carajás Hills are in Brazil's Eastern Amazon, between the Araguaia and Xingu rivers, and parallels 5° and 7° Latitude South. A location map is given in Fig. 1. It is an area of low mountains (maximum altitude 900 meters), covered by the Amazon rain forest. Annual average temperature is 25°C, ranging from 31°C (maximum) to 19°C (minimum). Annual rainfall averages 2,000mm. Although it rains throughout the whole year, heavy rains occur from December through March. At the beginning of the 20's, Brazilian explorationists made brief geological descriptions of the area. Due to the thick soil, scarce fresh rock outcrops and the tropical forest covering a completely unpopulated area, detailed geological studies were difficult and reconnaissance expeditions were limited to the river margins.

Jan 1, 1982

By J. A. Lombardi

Acid-Minesite-Solutions (AMS) are defined as copper-containing pit lake, tailing pond, acid-mine-drainage, and heap and waste dump irrigation solutions. All of these solutions are characterized by copper, acid and water contents that have value as individual commodities. HW Process Technologies, Inc. (HWPT) has developed nano- and hyper-filtration membrane methods for the separation of copper and other base metals, acid and water from AMS. These treatments are collectively called HWPT?s Engineered Membrane Separation® (EMS®) systems. The EMS® method of copper recovery produces small volumes of higher-concentration copper solution from large-volume, copper-dilute AMS. A case study of the 4,000 gpm Cananea EMS®-AMS plant for the recovery of copper from an acid-pit-lake resource is described. The EMS® method of copper removal from AMD and tails pond waters has been bench-scale demonstrated and are described, complete with projected budgetary capital and operating costs. Additional treatments for the recovery of sulfuric acid and high-quality water from the permeate (membrane passing) waters for the above-described AMS treatments are presented, with budgetary capital and operating cost estimates. [ ]

Jan 1, 2009

By F. J. Brenner

The Slippery Rock Watershed Coalition was organized to restore a 70 km2 portion of the headwaters of the Slippery Rock Watershed in northwest Pennsylvania. Thirteen passive treatment systems have been installed with engineering and funding provided by private industries, county government and the Commonwealth of Pennsylvania. In addition, experimental systems have been installed at the Jennings Environmental Education Center which, in addition to monitoring the systems installed within the watershed, provide an array of educational and research opportunities for secondary, college and university students. The coalition sponsors an annual seminar for students to present the results of their research and field trips for public officials and private citizens to learn how public and private partnerships work together to restore the Slippery Rock Creek watershed.

Jan 1, 2002

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining usage in the mining industry. A variety of machines currently finds employment: tunnel boring machines, roadheaders, continuous miners, surface miners, and augers. These machines have advantages compared to drill and blast mining methods, including increased safety, lower cost, uniform muck size, and accurately sized openings. A century of experience with mechanical methods has already paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hardrock mechanical mining machines. Mechanical miners will become integrated mining systems and will determine the design of mines, when several significant challenges have been met.

Jan 1, 2001

By M. A. Qianjie

The problems of coalmine safety in china remain unsolved for decades. Starting with the description on safety status quo of coalmine in china, different existing analysis and measures discussed for the safety problem solution of coalmine china. With the consideration of system thought in mind, the author present with a unique systematic reason analysis method on such actuality--individual analysis and general analysis--each for its particular purpose. Upon such cause analysis, construction of the safety system is made clear and, solutions for such problems provided.

Jan 1, 2006

By J. P. H. Steele, T. Vincent, C. Debrunner, M. Whitehorn

For a variety of reasons, the need for automation of underground mining equipment is growing dramatically, e.g., improved safety and health, availability of labor, deeper mines, and desire for more focused excavation. While there has been tremendous progress made in this direction, much needs to be done to reach the holy grail of an autonomous mining machine. This paper reviews a number of technological developments and presents research and development needs for future development. A report on our current project for the Western Mining Resource Center at CSM is included.

Jan 1, 2000

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study has been conducted to control iron in copper electrolyte streams using Eichrom Industries’s new Monophosphonic /sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27 g/L of iron and can be readily regenerated. In addition, the new resin can be easily synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydro-metallurgical streams.

Jan 1, 2000

By S. M. Pickering, L. T. Gregg

Appraisal of industrial minerals beneath privately owned land requires a different approach and mindset from valuation of base and precious metals or energy minerals, and from valuation of government-owned mineral lands. First, is it the value of inground minerals or of mining rights that is being sought? Second, value to whom, the mining company, a potential investor, the mineral landowner, a lending institution, the property tax assessor, or a condemnor? Third, how should mineral value be apportioned between the land and mineral owner, and a mining company with limited years of lease-hold interest? These and many other questions must be addressed before a valuation method and Discount Rate are selected. For various reasons the Income Method is most often used, with Net Present Value calculations made for long term predicted mining income. Choice of an appropriate Discount Rate is critical.

Jan 1, 2000

By S. A. Shuey, P. Taylor

The recycling of electronic waste (e-waste) tends to be a rather complex undertaking when considering the intimate bonding of materials in the average printed circuit board. The development of a recycling process is further complicated when considering the wide variety of products being generated under the heading of “electronics” as well as the constant change in materials of construction coupled with the speed at which electronics are changing. CSM researchers have undertaken a survey of the current state of pyrometallurgical processing of e-waste. This base-line will set the stage for the development of new recycling technology at CSM.

Jan 1, 2004

By E. Barnard

Tarkwa Gold Mine is located in south western Ghana, and is majority owned and operated by Gold Fields Ghana Limited. The Tarkwa CIL plant utilises a single low aspect 27' x 42' 14MW dual pinion drive SAG mill designed to mill 4.2mtpa (525tph). The plant was designed and constructed in a manner that would facilitate its expansion to 8.4mtpa (1,050tph). Since the plant was commissioned in September 2004, the SAG mill has consistently exceeded its nameplate throughput by up to 25%. Through the installation of a 26? x 36? 14MW dual pinion drive Ball mill along with additional upstream and downstream equipment, the plant will now be expanded to 12mtpa (1,500tph). This paper endeavours to outline the process and engineering design challenges along with the future construction challenges of the expansion in the midst of a fully operational plant.

Jan 1, 2008

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By T. Harrison

Surface coal mines in West Virginia are receiving stringent NPDES discharge limits for total recoverable selenium. With limits in the low parts-per-billion range, selection and implementation of proper sample collection and analytical methods are imperative for quality assurance and control and for consistency in results. Given the typical oxidized form of selenium in the water, the low limits and the large and variable flow rates from the watersheds, end-of-pipe treatment is difficult and cost-prohibitive to implement. Discharge locations in the remote and steep terrain exacerbate the problem. To evaluate options for end-of-pipe treatment at a Patriot Coal Corporation surface mining operation in West Virginia, CH2M HILL performed wastewater characterization for a range of key constituents and selenium species at three outfalls for selection and preliminary sizing of appropriate treatment processes. A preliminary evaluation of base and wet-weather flows was done to understand flow variability considerations for discharges. A conceptual evaluation of technologies to treat selenium to permitted levels was conducted in con-junction with order-of-magnitude life-cycle cost estimates.

Jan 1, 2010

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open-pit and underground mines of all sizes are regularly collecting point cloud data as laser scanning (LiDAR) and photogrammetry surveying devices have become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely and safely, rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing. This article specifically focuses on digital outcrop modeling and digital terrain engineering. Point clouds. The high-resolution and increasing availability of point cloud technology is rapidly improving open-pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations and typically the reflective intensity and/or the visible three-band color of each point (Fig. 1).LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device.Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles and even in a mobile backpack shown in Fig. 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds,” but this article does not address these due to their higher cost and lower versatility and mobility."

May 1, 2016

By G. Ferrara

Hydrocyclones and other dynamic separators are normally fed with pulps of water and solid particles. The particles have different sizes, shapes and densities and, except in the special case of mono-characteristic particles, are segregated into size, shape and density. Segregation is magnified by the high values of centrifugal acceleration in the hydrocyclones. This paper develops the theory of the segregation, indicates the major variables involved and reports experimental data of segregation under different operating conditions for mixtures of magnetite and/or ferrosilicon and non-magnetic minerals.

Jan 1, 1995

By Richard H. Olson

Talc is currently mined in the U.S. in six major districts. The size and depth of the ore bodies and their mineralogy dictate the types of products manufactured and the mining and processing methods which must be employed. The geology of the major deposits is well known and will be but briefly discussed The major emphasis will be placed upon the past history of the districts, the size and depth and configurations of the ore bodies, the ore mineralogy, and how all of these factors govern the types of mining and processing operations which may be employed in each of the districts.

Jan 1, 1984

The future phosphate rock deposits in South Florida contain a significant fraction of dolomite. The high MgO content of the rock is undesirable in the production of phosphoric acid. Several flotation schemes have been attempted to separate dolomite from phosphate rock. Alternately, Selective Flocculation process has been suggested to separate dolomite from apatite. A high MgO content rock was simulated by a 30:10:60 synthetic mixture of apatite, dolomite and silica. Single mineral selectivity was observed in the mixed mineral systems apatite-silica and dolomite-silica with Polyacrylic acid (PM) and Poly(ethylene oxide) (PEO) flocculants respectively but not realized in apatite-dolomite system with PEO flocculant. Heteroflocculation, suspected to be the major reason for loss in selectivity, was minimized by addition of a Site Blocking Agent (lower molecular weight fraction of PEO). Process parameters such as size reduction schemes, flocculant/SBA dosage, and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed mineral tests was translated into the ternary mixed mineral system, viz. apatite-dolomite-silica. In this presentation surface chemical characterization of the samples and their flocculation behavior will be discussed.

Jan 1, 1994

By B. T. Field

Pyroprocessing systems range from low temperature dryers to high temperature reactors. The materials and process requirements cover a broad spectrum. It is not the intent of this paper to do a detailed examination of individual processes and equipment, since that can be found in a multitude of other sources; rather it is the intent of this paper to examine the key process variables and offer empirical guidelines to assist in a user?s overall evaluation.

Jan 1, 1998

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016