Search Documents

By Christa Overby

As part of the City of Portland, Oregon?s East Side Combined Sewer Overflow Tunnel Project, nine separate 2,130 mm (84-inch) diameter reinforced concrete pipe microtunnel drives totaling approximately 2,380 m (7,808 ft) are being constructed to divert flows from several of the existing outfalls to the main tunnel. The drives were constructed in challenging ground conditions that include soft soils under the ground-water table, large amounts of wood and metal debris, and close proximity to sensitive structures. While all of the drives will be addressed, the focus of the paper will be on the 931 m (3,055 ft) continuous drive connecting Outfall 46, currently the longest microtunnel driven in North America.

By John L. Kaplin

The underground construction for the Phase I Combined Sewer Overflow(CSO) Project is on an impressive scale by any measure, appearing more so in a midsize city like Providence, RI. The Narragansett Bay Commission recently completed $350 mil-lion in construction to improve the water quality in Narragansett Bay. This project included a number of serious challenges, delays, and disputes. Looking back on this complex project completed within budget, it is hard to consider the work as anything other than a success. Along the way, this outcome did not always appear certain.

By D. Conklin

Annual fish monitoring of the Red River, NM from the town of Red River to downstream of Questa, NM has been conducted since 1997. This long-term dataset, sponsored by the Chevron Mining Inc. Questa Mine provides an opportunity to evaluate the fish community response to natural phenomena, such as landslides and drought. Hydrothermal scars are present on drainages to the Red River, which can contribute large quantities of sediment to the Red River during localized storm events. Sediment inputs from the hydrothermal scars result in decreased habitat and water quality conditions within the Red River. Landslides from the hydrothermal scars contributed large amounts of sediment to the Red River in the summers of 2002 and 2007. Resident trout populations in the Red River after summer 2002 were depressed at sites adjacent to and downstream of the hydrothermal scars. Resident trout populations had begun to recover by 2005 and 2006; however, after the summer 2007 landslide, the resident trout population was again drastically reduced. In fall 2007, 13 resident trout were collected from 11 sites in the approximately 23 km reach of the river, compared to 691 from the same 11 sites in fall 2006. Resident trout density and biomass has gradually increased since fall 2007, and flows have removed sediment from the study reach. A combination of increased sedimentation and decreased water quality were likely responsible for the decreased resident trout populations in the Red River. Drought and the lack of flushing flows appeared to exacerbate the problem of high sedimentation levels from 2001 to 2004. Climate models predict prolonged periods of drought and increased intensity of storm events, potentially resulting in less favorable conditions for the resident trout population of the Red River in this area.

Jan 1, 2011

By Luminita Calin

King County (Seattle, WA) is on a monumental task of building the new Brightwater System complete with a new treatment plant, three main conveyance tunnels, a new outfall into Puget Sound and other ancillary works. This paper will describe the first conveyance tunnel, Brightwater East currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor that is scheduled for completion in early 2010. The project located in Bothell, WA (north of Seattle) is in both King and Snohomish Counties. It was the first of the major tunnel projects that was scheduled by King County for the Brightwater System. The East Contract consists of the following major elements: 14,000 ft of 19'-2' EPBTBM mined tunnel using 16'-8' ID bolted, gasketed precast concrete segments for a primary liner; installing and encasing 14,200 ft each of 48', 66', 27', 84' in diameter steel pipes inside the tunnel along with three runs of fiberoptic cable; 2,430 ft of 72' in diameter microtunnel including three caisson shafts and associated structures; one Intercepting Structure (IS) shell to mine from that is 74 ft deep and 74 ft finished in diameter with 130 ft deep slurry diaphragm walls, tremie slab and final concrete wall lining; one Influent Pump Station shell (IPS) 83 ft deep, twin 77 ft inside diameter cells, with 160 ft deep slurry diaphragm walls, tremie slab, and final lining; two short 12 ft in diameter inter-shaft connector tunnels; one extraction shaft 40 ft deep by 40 ft wide and 140 ft long for connection to the new treatment plant piping.

By Stig Eriksson

In Switzerland two major railway systems as shown below in Figure 1 has recently been completed or is under construction: ¦Lötschberg, south of Bern which was commissioned in 2007 ¦Gotthard, south of Zurich which is scheduled to be commissioned in 2016The aim is to increase the transport capacity of the railway system and to transfer more transport of goods to the railway by offering transport of trailers and lorries on the new railway systems. It will have a positive environmental impact but also improve the congested traffic situation of the highways in north-south directionThe Gotthard tunnel is totally 57 km (35 mile) long and the Lötschberg tunnel is 35 km (22 mile) long. Both tunnel systems consist of two parallel single track tunnels connected with cross tunnels at every 333 m (1 093 ft). Additionally there are cross-over tunnels and caverns for installations and operation. In the Lötschberg tunnel, the majority of the excavation has been by Drill & Blast and in Gotthard tunnel the major part is being excavated by TBM.

By J. L. Carr

Every year, severe injuries and fatalities occur when a miner is struck or pinned by a continuous mining machine, shuttle car, scoop or other piece of mobile mining equipment. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Although hundreds of these systems are installed and in use in operating coal mines, the influence that coal has on the electromagnetic fields associated with these systems has never been rigorously quantified. NIOSH researchers have conducted tests to measure whether the proximity of coal has a significant influence on a popular design of proximity detection system. The system tested utilizes a low frequency magnetic field generator that would be mounted on the mining machine. At the NIOSH Safety Research Coal Mine in Pittsburgh, researchers measured the performance of a simplified proximity detection system of this type first on the surface then underground at varying distances from a coal face. Analysis of these measurements shows that the presence of coal does not have a measurable impact. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By H. Fayed

Two-phase (water and air) flow in a self aerated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). A 0.8 m3 model is considered. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Because of the lack of circumferential periodicity in this machine, the entire machine is modeled and unsteady simulations are conducted in the whole volume of the bulb. Uniform bubble diameter is specified, and the effects of bubble diameter are determined by conducting simulations for three diameters of 0.5, 0.7, and 1.0 mm. The unsteady air flow rate through the machine is predicted as an outcome of the simulations. Air volume fraction contours and velocity field in different parts of the machine are presented and discussed.

Jan 1, 2012

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow inby the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

Jan 1, 2007

By R. Tamblyn

Vertically stirred media mills are a highly effective low-footprint solution for the ultrafine grinding of industrial minerals. This work investigates the effect of media density on flow patterns within the mill. Direct irradiation of a media particle leads to decay through positron emission, consequently forming two anti-parallel gamma rays, which allow for the real time tracking of particle position. Grinding media of the same size, but with a range of specific gravities are followed using this method, and the effect on the flow within the mill is revealed. The technique is seen to be an effective method to highlight the velocity profiles within the mill, as well as the zones where grinding is less efficient ? areas of relatively low velocity and high residence time. The changing media is seen to effect the overall flow patterns within the mill, having consequential effects on the efficiency of the grind.

Jan 1, 2009

By R. J. Kline

Most accidents are the result of risk taking. They can happen anywhere. Our coal industry categorizes accidents by type, occupation, commodity, age, every way you can imagine. We now know, how many were injured and when, for all the different types of accidents. We have ask ourselves many times, why are we having accidents, how can we stop the accidents and fatals in our industry? Present numbers and projections do not show that this will happen. Serious accidents can result in fatalities. Fatal accident can be prevented, and the coal industry can achieve zero fatalities. How soon this happens, depends on a great number of factors. I will discuss accidents and reasons for us having accidents in an attempt to get to the root causes. The historical perspective will be touched on, and the risk and analysis of accidents will be probed.

Jan 1, 2000

By D. Brandt

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority. The Engineering Department started a project to improve fragmentation through blasting and thus increase throughput in the crushing system. It soon became clear that input from other departments was going to be required to make this a safe and economical project. Therefore the Crush and Convey and Ore Control departments worked together to evaluate all available data on blast patterns and explosive loads and tracked performance and results. Using image analysis, Drill Energy Index and databases, we have been able to improve fragmentation size and verify the results while controlling costs.

Jan 1, 2011

By M. Ahrens

The paper describes the main drive systems of an iron ore pelletizing plant and related important design aspects. It is shown how today?s drive systems provide the desired flexibility for the process and lead to high energy efficiency and system reliability. With respect to electric drives expansion projects have many technical issues in common with green-field installations. However, there are aspects where important, distinct differences occur. It is shown which considerations for selecting and sizing drive systems for such a plant as well as for integrating them into an overall plant control concept need to be taken into account. Besides the design of the drive systems a key aspect for such an expansion project is the network interaction. Harmonics levels at different points in the plant network need to be checked carefully with simulations during the design phase to avoid problems later-on during operation. The power factor compensation and the harmonic filtering of the new production line cannot be designed independently of the already existing plant. The paper highlights areas where problems could occur and which points need to be paid attention to when a plant is expanded.

Jan 1, 2008

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984

By L. M. Kocher, J. R. Heberger, J. P. Pollard, M. F. Nasarwanji

Injuries associated with hands and fingers are highly prevalent in mining and identifying factors associated with these injuries are critical in developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011–2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53%) followed by bone fractures/chips (26%). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals (pipe, wire, guards) and hand tools as the primary sources of hand and finger injury. Although information on glove use was limited, leather gloves were most often worn when an injury occurred. When worn, gloves were found to contribute to 20% of the injuries, indicating their potential to protect the hands, but also potentially put the hands at risk. Further research is necessary to determine performance requirements for gloves used in mining operations, specifically those offering cut and puncture resistance.

Mar 2, 2022

By Changjiang Li, Jun Yang, Qiang Fu, Xu Chang, Xing Wu, Yubing Gao

With the development of underground mining, the deformation of roadway floor has increasingly become a major constraint on the safe and efficient production of coal mines. To address the floor deformation that was caused by massive stress concentration in roadway, an innovative method based on deep-hole directional tensile blasting technology is put forward. By taking No.122108 working face in Caojiatan Coal Mine as engineering background and analyzing the mechanism of deformation, a numerical simulation and field test are carried out to verify the effect on deformation control of this technology. It is found that the deep-hole directional tensile blasting technology can actively control the fracture position of the roof in the gob area and cut off the stress transmission path, so as to relieve the stress in the roadway. And since different blasting parameters have different impacts on the stress relief effect, a numerical simulation is implemented and it is found that the stress relief effect is the best when blasting depth is set to be 32 m and the blasting angle be 60°. By applying the optimal blasting parameters to the field engineering test, it can be seen that the deep-hole directional tensile blasting technology could effectively reduce maximum stress value and stress field range of the both sides of the roadway, and make the stress field far away from the roadway, thus effectively controlling the deformation of the roadway floor. The deep-hole directional tensile blasting technology can effectively solve the problem of roadway floor deformation and can be safely applied to engineering sites.

Jun 13, 2023

By Joseph L. Young, Richard A. Bohling

To keep Homestake&apos;s Bulldog Mountain silver and lead mining and milling operation in southwestern Colorado workable, natural ground water and decant water from the mine&apos;s sand backfilling operation must be continually pumped from the workings. Left untreated, this water exceeds maximum allowable levels for various contaminants that may be discharged to the environment. To comply with regulations, a National Pollutant Discharge Elimination System (NPDES) permit was obtained and a mine water treatment plant for heavy metals removal was constructed in 1977. Due to equipment capacity and operational problems, and the lack of on-site technical personnel and analytic equipment, the first water treatment plant could not consistently meet permit limits. In 1979, Homestake entered into a consent decree with EPA and the Colorado Department of Health, calling for the construction of a water treatment facility to meet NPDES permit limits. Initial construction began in the spring of 1980 and the plant now produces effluent acceptable for discharge.

Jan 12, 1981

By Konner Horton, Adam L. Bedell, Don Del Nero, Brian Jones

"The City of Atlanta’s Water Supply Program Tunnel project includes a 7,315-m (24,000-ft) long, 4-m (13-ft) diameter, hard rock tunnel. A complex aspect of the project involves connecting five, blind bore shafts to the tunnel in a location close to current drinking water reservoirs. During the supplemental geotechnical investigation following the initial contract award, results from additional borehole geophysics were reviewed. Unfavorably oriented fracture sets forced a change in the original pre-excavation grouting program designed for that site. Real-time grout monitoring and geophysical data were compared to provide assurance that the program, as designed, correlated with the in situ ground conditions. Following grouting, results were modeled, and all grouting data were reviewed to determine if grouting was complete.Project backgroundThe current water supply system operated by the city of Atlanta’s Department of Watershed Management (DWM) consists of four, aged, raw-water pipelines, one of which dates back to 1893. Based on previous assessments completed by the DWM, the entire water supply system is at, or will soon reach, its recommended useful life. As such, the city acquired the Bellwood Quarry in 2006 with the intention to create a water storage facility with a volume of approximately 9.1 billion L (2.4 billion gal) to serve approximately 1.2 million people.The project location is shown in Fig. 1, which is generally in the northwest part of downtown Atlanta, GA. The overall project has been divided into two phases. The Phase 1 project connects the quarry and the Hemphill Water Treatment Plant (HWTP), and the Phase 1 Extension project connects the HWTP to the Chattahoochee Water Treatment Plant (CWTP) and the Chattahoochee River. A 7,315- m (24,000-ft) tunnel with a finished diameter of 3 m (10 ft) connects all three elements. The HWTP location is also where the city’s two most proximate drinking water reservoirs are located."

Jan 9, 2018

By Britta Schoesser, Zdenek Zizka, Markus Thewes

"The support pressure of a slurry shield corresponds to the in situ earth and groundwater pressure to ensure the stability of the tunnel face. The support fluid (bentonite suspension) penetrates from the excavation chamber into the pore space and transfers the support pressure to the granular structure of the soil within this zone. At the same time, the cutting tools rotate periodically with the cutting wheel and remove the penetrated soil up to a certain cutting depth at the face. Shortly after the tool passing, the penetration process starts again. Both, the support pressure and the soil excavation, act in the same direction at the tunnel face, but they are subject to different cyclic intervals. This relationship between the time needed for the transient penetration process and the interval of the cyclic passage of the cutting tools at a local point at the face is examined and the impact onto the global face stability is discussed. INTRODUCTION Slurry shields are usually deployed for excavations in soft ground. The main application range is in non-cohesive soils (DAUB Recommendations 2010). In non-cohesive granular soils, the tunnel face stability is one of the key design issues. The slurry shields make use of pressurized bentonite suspension (slurry) to support the unstable tunnel face. To support the tunnel face effectively, the slurry pressure has not only to counter the groundwater pressure, but also has to be transferred into an effective stress to support the soil grains. In general, the pressure transfer can be achieved in two ways: (1) with a thin flexible membrane or (2) a penetration zone. The membrane (1), called filter cake, creates a thin impermeable layer from bentonite particles directly on the tunnel face, and enables a transformation of excess slurry pressure into effective stress. In case of penetration zone formation (2), the excess slurry pressure is transferred onto the soil skeleton along the entire penetration depth by shear stresses between slurry and soil grains. These theories, presently applied to assess the pressure transfer on the grains within slurry shield tunnelling, are originating from diaphragm wall technology, e.g. Müller-Kirchenbauer (1977), Kilchert and Karstedt (1984). They assume that the support pressure transfer mechanism is built-up instantaneously on the whole tunnel face and is not damaged or influenced by the interaction with excavation tools. These assumptions are valid for conditions during the excavation of diaphragm wall trenches whose bottom is excavated and the walls of the trench are supported. At the tunnel face of a slurry shield, the support suspension acts on the same area as the soil excavation. Hence, the conditions on the tunnel face are transient (time dependent) due to the time period needed for the penetration process of the slurry and the periodical damage of the pressure transfer mechanism by excavation tools (Fig. 1a)."

Jan 1, 2016