Search Documents

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By P. C. Thakur

Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1952 at the Humphrey Mine of Consolidation Coal Company for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for eight years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300-to 600 m, with reasonably precise directional control and within practical cost limits.(1) Mining Research Division of Continental Oil Company, the parent company of Consolidation Coal Company, began a research program in the early 1970's to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary Its of this research have already been published.(2) To date nearly 4500 m of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: 1) The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3 percent in course of two to three months from original values of nearly 0.95 percent.

Jan 1, 1979

By Denis Tepavac, Mark Trim

Structural performance of fiber reinforced concrete (FRC) depends on its ability to carry tensile forces after cracking. Australian Standards AS5100-2017 and AS3600-2018 are the only available design standards that establish a test procedure to determine strength and toughness of an FRC in direct tension. Direct tensile testing of fiber reinforced shotcrete samples was performed to determine if the model and guidelines in AS5100/3600 were applicable to shotcrete; all previous testing was from cast samples. In addition to direct testing, micro CT-scanning was also performed. The paper presents tests performed, results, and how the tests could be used on future projects. In addition, a brief summary is provided of the guiding structural mechanics used for estimating residual tensile strength and test methods utilized to verify those estimates.

Jun 13, 2023

By Serhat Özdemir, Derya Öz Aksoy, Pınar Aytar Çelik, Ahmet Çabuk, Sabiha Koca, Hüseyin Koca

In carbonate flotation, oleate has been used for many years as a collector in industrial scale. Compared to sulfide minerals, the flotation of carbonate minerals requires more collector consumption and has lower yield and selectivity. It has been previously shown that surfactin provides higher yields in smaller amounts than oleate in the bioflotation of calcite as one of the carbonate minerals. In this study, the usability of surfactin as a flotation collector for magnesite was investigated. For this purpose, the adsorption of surfactin on the magnesite surface was inspected with analyses such as FTIR, SEM–EDS, contact angle, and zeta potential measurements. In addition, the effect of surfactin on the surface tension of water was also revealed. The same analyses were also performed for oleate as a reference point. All flotation experiments were performed without optimizing with both collectors. FTIR results showed that the surfactin, like oleate, was chemically adsorbed on the magnesite surface. Surface tension analyses showed that the surface tension of water decreased to approximately 32 N m− 1 at 10− 4 M oleate concentration, and this value decreased to below 25 N m− 1 at the same surfactin concentration. According to contact angle measurement results, the contact angle of magnesite was 85° after the surfactin adsorption of 2 × 10− 4 M concentration, while this value remained at 46° for oleate. Finally, according to flotation experiments, high temperatures and high collector dosages are necessary for acceptable flotation recovery with oleate, yet surfactin can produce the desired result at ambient temperatures and lower collector amounts.

Dec 13, 2022

By G Luxbacher

Computer simulation of mine ventilation systems is rapidly becoming an essential tool in mine planning and design. This paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve mainly for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria, could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1977

By B. Pesic

Northwest Alloys, a wholly owned subsidiary of Alcoa, produces magnesium from dolomite by reduction with ferro silicon and aluminum. This process produces alkaline by-products in quantities that allow their consideration for use as commercial by-products. Two such products are dicalcium silicate slag, Di-Cal, and magnesium oxide condensate, MgO. The alkaline properties of these materials offer acid neutralizing capability comparable to the traditionally used lime, therefore, warranting a study for their use in applications where the neutralization of acidic waters or process solutions is required, such as treatment of mine waters. In this ongoing study, three mine waters (Bunker Hill Mine, Berkeley Pit, and Blackbird Mine) were selected for treatment with Di-Cal and MgO. Lime was used as the background control. The solid precipitates were subsequently contacted with pure water at four different pH conditions for stability testing of prepared metal precipitates (expanded TCLP). It was found that neutralization with Di-Cal results in precipitates which are of equivalent to superior stability than those from lime treatment.

Jan 1, 1999

By W. F. McDermott

The transportation of solids by pipeline is not new. In 1891 a United States patent broadly covering a method of pumping coal with water was granted to W. C. Andrews. His pilot plant was constructed on what is now the site of the New York Public Library in Manhattan. His process was applied to pumping coal mine waste back into the worked out portion of coal mines. On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this 5.0 million dollar installation climaxed three years of development, testing, and construction and proved the Company's faith in pioneering this unique transportation method for iron ore. This paper will discuss some of the more pertinent items in connection with that three- year period. Also to be discussed will be the operation of this line during the past eleven months.

Jan 1, 1968

By Kenneth J. Edmiston

The objectives of this paper are: to review the current status of chloride leach processes for sulfide concentrates, to make an evaluation as to the applicability of chloride leaching for replacing pyrometallurgical processes and to comment on recent advances in construction materials. The paper does not delve in detail on process chemistry. Sufficient references are presented on each process to allow the interested researcher to obtain process chemistry details. GENERAL The fact that chloride oxidates can solubilize base metals from sulfide concentrates has been known since the 1880's. The work of Hoepfner in 1902 was particularly accurate for its time with regard to the chemistry of chloride solutions. Recent work has dealt with the understanding of chloride extraction thermodynamics by modelling the behavior of metal chloride complexes. In the last several years several excellent review articles and symposiums have been issued covering chloride chemistry (1 thru 6).

Jan 1, 1984

By Ralph W. M. Lai

The liquid membrane separation process was first patented in 1968 for separating hydrocarbons.(1-4) This stimulated many researchers to join in the area of separating organic compounds. l Since then, its applications have been extended to the removal of contaminants from waste water,(12-33) encapsulation of enzymes and/or microorganisms for reaction and/or separation, (24-28) oxygenation of blood (artificial lung),(19) removal of toxins from blood (artificial kidney)(26,20) and metal extraction.(31-63) This paper discusses the possible process schemes for using liquid membranes to separate and concentrate copper ion from its acidic leaching solution.

Jan 1, 1982

By Harold L. Lovell

The current interest in sulfur recovery from coal measures is indicated by a recent report prepared for the Public Health Service (1) It was noted that the concentration of pyrites to a product containing 42-48 percent sulfur should be relatively easy with present equipment. It was also pointed out that a utility potential exists for the high-grade iron concentrate which results as a by-product of the consumption of pyrites in the acid-making process. However, economics, marketing characteristics, location, transportation, pyrite levels and coal characteristics all strongly influence the feasibility of fostering industrial development of such processes. The extent of pyrite recovery and product quality is intimately related to pyrite particle size and its degree of liberation, a consideration usually given greater emphasis in metal ore preparation than in processing coals. Consequently, fine crushing to nearly 20 mesh probably will be essential for maximum practical processing. It appears that any process separating pyrites from a coal must involve a reprocessing of the normal preparation plant refuse, although some yields can be attained from certain existing operations as products from, a shaking table or a jig. Further, the existence of millions of tons of coal refuse cannot be ignored as a mined source of raw materials. The recovery of saleable products from such wastes, although untried on a large scale under current conditions, not only offers a realistic source of sulfur but also would achieve a secondary refuse with the minimal contents of substances which incite and propagate the burning of organic and inorganic combustibles. These silicate materials, thus beneficiated, also offer some potential for economic utilization. Some significant tonnages of pyrites have been produced from coal measures in the past, but the experience was, in general, not consistent with current coal preparation practice. The processes involved did not include cyclones and heavy media; nor were they carries out under the sociological environment concerned with pollution as exists today.

Jan 1, 1967

By Ahmed M. Yousif, Walid M. Abdellah, Galal M. Abdel Wahab, Amal E. Mubark

The present work is concerned with selective dissolution of niobium from Gabal El Faliq concentrate sample by using fluoridefree process. The chemical analysis of concentrate sample revealed the presence of high amount of ZrO2, Nb2O5, Re2O3, and HfO2 assaying 33.6, 1.99, 4.8, and 1.2%w/w respectively. Several economic minerals including zircon, samarskite, fergusonite, and xenotimewere recorded in the studied sample. About 98%of Nb content was selectively dissolved at the optimumconditions of 1:2 concentrate sample: KOH weight ratio, 2.5 h fusion time, and fusion temperature of 550 °C. Organic solvent extraction process using Aliquat 336S in xylene was effectively used for preparing pure Nb2O5 (98.95%).

Oct 22, 2019

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

This paper combines theoretical and experimental analysis to conduct relevant research to improve the accuracy of predicting paste yield stress by slump flow. The analytical model of slump flow for yield stress is derived based on a mini-cylindrical mold with a height-to-diameter ratio of 1. It shows that the dimensionless slump flow is a monotonic decreasing function of the dimensionless yield stress and is independent of the material type (specific gravity), which provides a theoretical basis for quantifying the rheological properties of paste with slump flow. Three different tailing-prepared pastes were tested for their slump flow and implemented rheological tests simultaneously. The yield stress is obtained based on the Bingham model fit, as the measured value of the yield stress is substituted into the derived theoretical model. The studied pastes yield stresses range from 34.78 to 524.08 Pa, with corresponding dimensionless slump flow of 3.43 to 1.09. The results showed that the calculated slump flows were generally greater than the measured values. The analysis showed that this was mainly due to the thixotropy of the paste, with minor deviations ranging from − 1.5 to 5.8% for the less thixotropic pasted prepared from tailing C. An approximate analytical solution for yield stress as a function of slump flow is obtained using Taylor’s formula. However, it is unsuitable for predicting the yield stress because the yield stress calculated by this function is much higher than the measured value. The empirical yield stress model was constructed and experimentally verified. The results show that the empirical formula has high accuracy and good generality. The deviation of the studied pastes is between − 15 and 5%, which provides a practical method for rapid and accurate prediction of paste yield stress in mine sites.

Jun 1, 2023

Underground mine designs typically try to avoid extraction beneath streams and rivers of any significant size, especially when the overburden rock thickness between the stream bed and the mine is thin. Potential issues with mining beneath streams include excessive groundwater inflow to the mine; weak ground (roof, floor, and pillar) conditions; horizontal stress effects; as well as stream loss and other potential adverse environmental effects. However, there are times when crossing beneath a stream or river is necessary to move into a new area of mineral reserve without creating additional mine access points from the ground surface. Often, stream crossings are completed without thorough assessment, potentially resulting in increased costs, decreased safety, and, in some cases, failure to advance the mine. Selection of the most favorable location(s) to cross the stream must account for numerous factors and the associated assessment often requires a multidisciplinary approach. Stream crossing investigations often require geological, hydrogeological, geotechnical, and geophysical expertise. Phases of stream crossing investigations include desktop evaluation of maps and aerial photography, stream bed observations, drilling, detailed rock core logging, downhole geophysical surveying, hydraulic conductivity testing (packer testing), geotechnical laboratory testing, assessment, and reporting. The deliverables from a stream crossing assessment typically include geological, geotechnical, and hydrogeological characterization of potential stream crossing locations; classification of favorable and unfavorable crossing locations; recommendations for entry design and pillar sizing; and recommendations for if, and how, to conduct pre-grouting activities. Examples of technical aspects of data collection and assessment are provided based on decades of industry experience conducting stream crossing assessments in various underground mining scenarios.

Jul 28, 2020

By Howard L. Hartman

The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry is not unaffected by the drought: not only is research lagging, but hard- pressed universities are going to the private sector for funding. This paper's thesis is not that mining companies should shower universities with philanthropy, but that a quid pro quo ought to be exacted: a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that may lend itself to adoption by our industry.

Jan 1, 1984

By T. Gelpe

A digital simulator of classification and grinding circuits is used to evaluate the performances of various flowsheets. For a given flowsheet configuration, unit processes dimensions and operating conditions, the simulator calculates the steady-state values of the process variables. A supervisory algorithm is implemented in the simulator to determine the conditions which meet the required criterion on operation, tonnage and product quality. Calculation illustrations are proposed for the design of wet and dry grinding circuits. The performances of various arrangements of cement clinker and sulphide ore grinding flowsheets are evaluated and discussed.

Jan 1, 1983

By George L. Atwood

The western phosphate field, one of the United States' great mineral resources, lies within the western states of Idaho, Utah, Wyoming and Montana. This Permian sedimentary deposit has been known since the turn of the century and since the 1920's has been mined for its phosphate content. Isolation from markets and relatively high mining costs have restricted development as compared to eastern United States deposits, but nevertheless a significant western phosphate industry has developed. Geographically the deposit covers an enormous area of about 337 000 km2 (130 000 sq miles). It covers Idaho from Pocatello east- ward, western Wyoming to the eastern flank of the Wind River mountains, and extends well into southwestern Montana and into a large area of northeastern Utah north of the Uinta Basin and east of the Salt Lake valley.

Jan 1, 1983

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

By Yngve Jordal, Sverker Hartwig

The IVAR Project is Norway's largest sewer project presently under construction. One part of it is an 8.1 km (26 575 ft) long, 3.5 m (11 ft 6 in.) diam tunnel, bored in one year. The tunneling project has been running smoothly; however, not everything has been easy. A few of its features are highlighted in this paper: The use of 9 0 (12 cu yd) muck cars on a double track back-up in such a comparatively narrow tunnel. Employing only four men in the tunnel, including the loco driver. A quartzite dyke - 96% quartz with 350 MPa (50 000 psi) and more compressive strength - turned out to be 640 m (2 100 ft) thick instead of the predicted 90 m (300 ft). Passing under a gaseous swamp with only same 5 m (16 ft 5 in.) of rock cover on top.

Jan 1, 1991

By K. Norrena

Grade control in open pit mining requires the specification of dig limits that account for mineral grades, economic costs, and selectivity of mining equipment. Visual identification of ore rock types is ideal, but this is not always possible in lower grade disseminated deposits where ore/waste contacts are not visually discernible. In this case, conventional grade control practice consists of a two-step procedure (1) create a map of mineral grades at some selective mining unit scale, and (2) determine practical ore-waste boundaries or dig limits on the basis of the gridded block grades or assay information. This procedure is laborious, depends on a subjective assessment of where the boundary should be, and may be economically sub-optimal. We pose the determination of dig limits as an optimization problem and solve that problem with the technique of simulated annealing. Simulated annealing has the unique advantage of being able to combine multiple non-linear constraints into a single objective function. We use maximum profitability and the ability of the equipment to mine the proposed dig limits as constraints in the determination of optimal dig limits. We require a map of expected profit for eah block. Geostatistical techniques are recommended, for mapping expected profit but not necessary. Geostatistics will provide a quantification of the uncertainty in the grades within rock types using all available blasthole samples and exploration drilling. Some variant of L-optimal estimation or kriging can be used to determine the block-by-block classification that is economically optimum. We also need the expected profit for each block. It is unrealistic to assume free selection, that is, each block cannot be extracted independently of its neighbors. The optimal balance of ''accepting dilution'' and ''wasting ore'' is achieved to maximize profit subject to equipment constraints.

Jan 1, 2001

By G. T. Adel, J. D. Miller, C. L. Lin

Washability analysis determines the maximum separation efficiency that can be achieved in the operation of coal preparation plants. Unfortunately, there are no on-line techniques for determining this most fundamental information. It now appears possible to determine coal washability on-line through the use of x-ray computed tomography (CT) analysis. This paper presents the results for the development of a CT-based, on-line coal washability analyzer. The development of appropriate hardware and software necessary to adapt a CT analyzer for use in determining coal washability is discussed. Testing of the analyzer using well-characterized coal samples is presented.

Jan 1, 2000