Search Documents

By W. J. Dolinar, S. P. Sandoval

The US Bureau of Mines (USBM) implemented the Fe2+/ Fe3+-SO2 anode reaction in a Cu-electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/ m2 (24 A/ft2) and 40°C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb), compared to conventional electrowinning. Acid milling 5was completely eliminated, and the SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1996

By C. Anastasiadis

The wettability of sandstone was investigated using the technique of dielectric spectroscopy in the frequency interval 1kHz-1MHz. The natural wetness of the material was modified to get two different sets of samples, one with sea-water wetness and the other with crude oil wetness. Measurements showed that the electric responses of water-wet and crude oil-wet samples were markedly different beside the fact that the dielectric response of both groups of samples obeys a general fractional power law. The dispersivity, of the complex permittivity component that expresses the material loss with respect to the electric field was found to be the most suitable parameter to check the wettability of the samples.

Jan 1, 2005

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Because of increasing production of fine coal during mining over the past century and because of inefficient fine-coal recovery technologies, a vast reserve of high-quality coal now exists in refuse ponds. A novel finecoal circuit, consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column, was evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,170 kJ/kg with 60% mass yield. Results from the treatment of two refuse pond materials are presented in this paper.

Jan 1, 2002

By P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines has been engineered, designed and operated. A non-transferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide, and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained at above 1673 K (1400 C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbon monoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pressure, and average reactor temperature. The interactions of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1993

By L. Evrard, M. Van Camp, J. Y. Yen, R. G. Reddy, D. Mantha

Viscosities of two industrial lead blast furnace slags have been experimentally determined as functions of composition and temperature. A Brookfield viscometer with alumina rods and crucibles were used. Experiments were carried out between 1200 and 1573 K in an argon atmosphere with up to 5% addition of FeO, MgO, and SiO2 to the slags. Results showed that 1) the viscosities of two slags decreased with increase in temperature; 2) addition of FeO decreased the slag viscosities; and 3) addition of MgO and SiO2 increased the slag viscosities. Use of the above slag compositions with the addition of FeO is recommended for successful lead smelter operation.

Jan 1, 2005

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By Wayne A. Van Voast

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 1,250 m3/day of flow from storage and created a piezometric depression of 3 meters or more as far as 1,500 meters from the mine. No wells have yet become non-productive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures or ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand, silt, and clay. Hydraulic conductivities and storage coefficients are comparable with those of undisturbed confined aquifers. Water quality in mined lands is highly diverse because of diverse spoils lithologies and poorly-established ground-water circulation. Ground water in spoils is more mineralized than in the coal beds and chemically resembles waters from sandstone aquifers. Hydrologic effects of mining will not be catastrophic or widespread but may have local significance. Most notable changes will be in water quality; availability will not be permanently reduced.

Jan 1, 1978

By Thomas E. Ban

The continuous sintering process was invented more than 60 years ago by two metallurgists, Arthur S. Dwight and Richard L. Lloyd, who saw a need for automation in mineral processing. Their specific objective was to beneficiate copper ore by desulfurizing and agglomerating it for copper blast furnace smelting at the Cananea plant in Mexico1. Since their early development the process expanded widely in scope, size, and application. The current worldwide sintering applications exceed 250 million tons per year for agglomerating ores of lead, manganese, zinc, and iron. Sintering is also widely used for production of sintered lightweight aggregate from clays, shales, and fly ash. The continuous sintering process took on wide expansion during the 1960's in foreign countries. Plants for production of approximately 135 million tons per year were built in these countries for sintering iron ore fines as shipped from new iron ore projects of Canada, Liberia, India, Brazil, and Australia. This expansion represented construction of approximately 80 new sintering plants, some as large as 15 thousand tons per day production on a single large sintering machine. Sized self-fluxing or highly fluxed sinter has become recognized as a premium blast furnace charge and has enabled blast furnaces of Japan and Europe to produce upwards of 10,000 tons of metal per day with coke rates less than 1,000 pounds per ton of metal. This coke requirement is practically 50 percent of the ordinary rates achieved during the early 1950's when the peak blast furnace production was less than 113 of the current records.

Jan 1, 1975

By T. W. Newell

Small tonnage ore bodies can be developed at a profit on a short life basis. Such is the case of the Bardon Mine in. the Big Indian Mining District in San Juan County. Utah. Faced with a small initial tonnage of high grade uranium ore, the Shattuck Denn Mining Corporation Engineers developed some new ideas for sinking the shaft and planned extraction to warrant the capital risk to mine a limited reserve. The Bardon Mine is located fifty miles southeast of Moab, Utah in the south end of the Big Indian Mining -district. Shattuck Denn Company, a wholly owned subsidiary of the Shattuck Denn Mining Corporation, manages and operates the property under an operating agreement with Kerr-McGee Oil Industries, Inc. of. Oklahoma City. Oklahoma, and Anderson Development Corporation of Albuquerque, New Mexico. Based. on Kerr-McGee drilling., a tabular ore body about 350 feet long by 250 feet wide with an average thickness in excess of seven feet was indicated.- The ore body strikes easterly-westerly and dips from nine to twelve degrees to the south. Uraninite is the dominant uranium ore mineral associated with vanadium. The ore occurs in an arkosic conglomeratic sandstone with some interfingering of mudstone and shale in the Mossback member of the Chinle formation in contact with the underlying Cutler formation. The ore horizon is overlain with 40 to 60 feet of mudstone and shale. Fortunately, the back. immediately over the ore is a reasonable competent shaley sandstone which has made a fairly good. environment for roof bolting.

Jan 1, 1960

By John E. Caffrey

Mr. William. J. Montgomery in his book "Theory and Practice on Mine Ventilation stated "Ventilation is vitally important to underground mining for three reasons: First, it sweeps all workings with a plentiful supply of air and drives to the outside the smoke, gases, and contaminated air which would be injurious to the miners; second, it dilutes and renders harmless the explosive gases emitted from the strata, thus eliminating the dangerous conditions caused by the accumulation of these gases; third, it keeps the mine air as nearly as possible of the same composition as the outside air, thus giving to the miner the healthiest possible condition in which to work...." Specific methods to achieve the above basic reasons for mine ventilation were established in the Federal Coal Mine Health and Safety Act of 1969. Sections 303(y)(1); (y)(2), and Section 317(f)(4) of the Act, which can be broadly described as entrapment features, are controversial and debatable in the minds of many mining engineers in their intent and method for affecting, 303(y)(1) in certain cases prohibits the use of belt haulage entries as an intake for face ventilation, This is to say that air traveling in a belt entry will be placed into the returns and not used for face ventilation, 303(y)(2) limits the velocity of the air on trolley haulage entries. The regulations, as published in the Federal Register, have set this limit at 250 feet per minute unless a higher velocity is approved by the District Manager.

Jan 1, 1972

By John A. Reeves

The unit-train concept of moving raw materials .is considered by many railroad men as the most signifigant contribution to reducing rail freight costs since the introduction of the diesel locomotive. The idea, which involves assigning railroad equipment to only one haul and keeping the equipment rolling results in the maximum utilization of equipment. For example before the unit train was plaged in servige on coal hauled to one of Mid. Continent's customers, about 900 cars and 9 locomotives were needed to move the coal requirements for this plant, compared with. 250 cars and 6 locomotives used by the present scheduling of unit trains. If the economics of unit-train movements are to be achieved, coal companies no longer can use railroad cars as small storage bins on wheels to accumulate their coal in trainload shipments, but, rather, must build large bins which incorporate facilities for the rapid loading of railroad cars in a minimum length of time. In this manner railroad equipment is operated at a high degree of efficiency 'with consequent dollar savings. After negotiations between Mid-Continent, the customers and the Railroad, it was decided a unit train loadout and storage facility at Carbondale was required in order to reduce the delivered price of coal to the customers and thereby contribute to the reduction in the cost of manufacturing steel. Carbondale was selected as the bin site location, because the cost of constructing a railroad to Redstone could not be justified for the tonnages anticipated.

Jan 1, 1969

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By Edward C. Krug

"You are to use the word ... purely for its selling power. It is a name they venerate. As a result, you can use the word ... to ... get [them] to practice, not only without shame bit with a positive glow of self-approval, conduct which, if undefended by the magic word, would be universally derided." (C.S. Lewis, The Screwtape Letters, 1982, p. 162). "We need to tear everything down over a period of time and reconstruct a whole new world, planned top to bottom. "Right now there are just way too many people on the planet [5.3 billion]. `If we had ... an ethic ... we could cut back to 250 million-350 million people. `The United States is ... a bunch of pigs ... the average citizen ... [uses] maybe 70 to 80 times as much as anyone in the Third World.` "The indigenous pople were the ones that were right! I mean, they had their own religion, their own ethics and their own technology. We just went down a wrong road. "So when he says, `We got to rebuild the whole world,' you have no doubt this is serious sentiment .... And it is finally this world view that distinguishes (Ted) Turner as a media mogul and an environmentalist. It is why Worldwatch's Lester R. Brown told me Turner was `truly a visionary. "'(Interview of Ted Turner, Audubon magazine, November-December 1991. On Dec. 28, 1991, Ted Turner was name Time magazine's "Man of the Year." Clearly, media and environmental leadership agree with Turner's openly stated beliefs.)

Jan 1, 1992

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By Ronald E. Heuer, Debra L. Virgens

INTRODUCTION Behavior of clay soils in response to tunneling is reasonably well understood by reference to the tunnel stability factor NT = Pz/su (Peck, 1969; Heuer, 1974). With this analysis tool, care must be taken to use a value of clay shear strength which represents the actual mass strength, considering such factors as slickensided fissures often found in stiff and hard clays. Behavior of clean sand and gravel soils is also reasonably well understood. Above the water table these soils must be assumed to act as running ground unless they are known to have significant cementation or have a very dense and angular interlocked grain structure. Below the water table they must be tunneled using some form of groundwater control such as dewatering, grouting, freezing, or internal fluid pressure in the tunnel such as compressed air or a slurry tunneling machine. The internal fluid pressure must approximately balance the external water head. Without such precautions these soils behave as flowing ground and may yield large volumes of water flow into the tunnel. A wide range of very fine sand, silty sand, cohesionless silt, and clayey sand soils exist in nature in a variety of geologic environments. The behavior of these soils in response to tunneling, and guidelines for anticipating their behavior, are not well described in the literature. Because of their content of fine particles, these materials may behave as if they initially have appreciable cohesion and moderate to low permeability. They may exhibit significant standup time, and require tunnel internal fluid pressure (compressed air or slurry pressure) less than the full external water head. It is important to be able to estimate the behavior of these soils when planning construction methods. For example, if the external water pressure is 140 kPa (20 psi), but soil stability at the tunnel face can be achieved as a compressed air pressure of 80 kPa (12 psi), a large cost savings may result.

Jan 1, 1987

By Bruno Sceresini

The Filblast Cyanidation Process incorporating intense high shear mixing, high gas mass transfer efficiency and high oxygen concentrations under conditions of elevated pressure has now been been successfully applied in gold cyanidation mills since May 1993. The first commercial unit had a slurry capacity of 110 cubic metres per hour. Since then 230 and 450 cubic metre per hour units have been installed and a 1,000 cubic metre per hour unit has been designed. Laboratory and pilot plant Filblasts have also been built. The reactor is a robust, compact in-line or end-of-line device and may be constructed out of a wide range of materials including wear and corrosion resistant alloys and ceramics. The Filblast Process may be applied to high temperature leaching of refractory gold ores and base metal concentrates. The development and application of the Filblast Gas Shear Reactor as a cyanidation tool has removed the constraints of plant size in cyanidation applications in mobile or readily transportable gold plants. A 250,000 tonne per annum fully modularised gold ore treatment plant with the Filblast and AARL Pump Cell as core technologies is nearing completion. This plant includes several novel features which are predicted to achieve widespread adaptation in modem cyanidation plants. This paper presents a briefreview of the development of the technology and the principles incorporated in the Filblast system. A number of case studies are presented which show significant financial benefits due to more efficient reagent utilisation, higher recovery and increased through-put.

Jan 1, 1997

By E. Stamboliadis

Gravity separation techniques were used in the early years to extract native metal nuggets and flakes from placer gold deposits. This was relatively easy for visible metal grains. As the size of the grain becomes smaller traditional gravity separation techniques become inadequate to recover native gold. Cyanidation was invented as a solution to the problem. According to it, gold and other precious metals are dissolved in water by sodium cyanide. The result was a drastic increase of world gold production but at the same time environmental issues were raised. In Greece gold mining has become equivalent with the absolute destruction of the environment and is under extinction. In the last years a new type of gravity equipment have been produced which create a gravitational field up to 200 G and can separate gold from gangue minerals at sizes below 50 µm. The strong gravitational field is created by centrifugal forces and the separation occurs in a fluidized bed, formed by water flow. Accumulations of finely disseminated native gold are found in the sedimentary sequence of the Flysch of the Ionian Zone. The main gold minerals are gold and electrum present as free metal flakes and micro nuggets in the size range between 5-250 µm. Test work, using the Falcon SB40 centrifugal concentrator, at the Department of Mineral Resources Engineering at the Technical University of Crete, has shown that this particular type of gold ore can be processed by gravitational methods that require no reagents and are environmentally safe.

Jan 1, 2003

By T. S. Golosinski

Most of the 154 t (170 st) truck fleets that were predominant in large surface mines in the 1970s and 1980s are approaching the end of their economic life. One replacement option considered by mine operators is a change to the 2 18 t (240 st) trucks. A comparison of load capacities between the 1.54 t (170 st) and the 2 18 t (240 st) trucks indicates a large productivity advantage in favor of the 218 t (240 st) trucks. This advantage, however, is often reduced by a number of site-specific factors. Therefore, a careful evaluation is required to define the actual benefit of changing to the large trucks. This article discusses some important factors that have an impact on truck size selection, based on several different studies. 218 t (240 st) trucks The 2 18 t (240 st) rear dump trucks were first introduced for surface mine service almost 10 years ago. However, it is only during the last few years that this equipment has gained acceptance in the surface mining industry. About 250 units were employed in surface mines worldwide at the beginning of 1992, and further purchase commitments are being made. Encouraged by the mining industry’s interest, all major off-highway mining truck manufacturers now offer 218 t (240 st) models (Table 1). At present, the existing 218 t (240 st) truck fleets are dominated by electric drive trucks. However, recent introduction of a 2 18 t (240 st) mechanical drive truck rounds out the development of this truck size.

Jan 1, 1992

By R. A. Pond

Two 6.17 m (20 ft 3 in.) diameter raises, concrete-lined to 5.49 m (18 ft) inside diameter, were completed in 1978 at the Monterey Coal Company Number One Mine near Carlinville, Illinois, by Frontier-Kemper Constructors. These two raises are the largest in cross-section yet completed by full-face upreaming, and the success of this project is expected to increase the application of raise-boring to coal mine shaft construction. WHY 6.17 M (20 FT) DIAMETER ? Raise boring is well accepted in the metal mining industry for a variety of applications, and is gaining in acceptance in the civil works construction industry. The use of raise boring to construct vertical openings for coal mines has not been as widely accepted, even though coal mining requires, per mine, the greatest number of openings to the surface of any underground activity. Several factors have influenced the low utilization of raise boring in coal mining: 1. Coal mine shafts must often be of large diameter to pass the required high volumes of ventilation air at acceptably low water gage pressures. Cross-sectional areas of finished shafts exceeding 23.23 sq m (250 sq ft) are common. 2. The life of ventilation shafts is comparatively long, and the typical sedimentary strata overlying coal seams normally require that the shafts be lined. Shafts on the intake ventilation circuit must have permanent water-tight linings. 3. Unconsolidated overburden at the surface is often thick, and as reaming cannot be safely utilized in unconsolidated material,

Jan 1, 1979

Terminology. The term potash originated in "pot ashes" produced by burning wood to ashes in iron pots and then leaching out the soluble salts, chiefly potassium carbonate, from the residue. In modern usage potash is a generic term for various potassium salts used in agriculture and industry. More specifically, it denotes the oxide of potassium, K2O, and the content of potassium in ores and products is stated as weight percent of K2O present. Its salts are commonly referred to as muriate of potash, sulfate of potash, etc. The presence of an adequate supply of available potassium in the soil promotes the health and improves the quality of the plant. insures greater efficiency in photosynthesis, increases resistance to certain diseases, offsets the effect of an oversupply of nitrogen, and helps the plant to utilize soil moisture more advantageously. ("Soils and Men," U.S. Dept. of Agriculture Yearbook 1938.) Occurrence. Potassium ranks seventh among the elements in abundance. It is estimated to constitute some 2.6% of the lithosphere and is found in soluble forms in the oceans, lakes, rivers, and subsurface waters. It is also an important constituent of plant and animal life. Commercially significant accumulations of potassium salts occur in underground deposits formed in past geologic times by evaporation of ancient bodies of saltwater, inland drainage basins, and shallow sea lagoons. The potash content of such waters was the end result of weathering and leaching of insoluble potash-bearing aluminosilicates, such as feldspars, micas, leucitcs, and others. The concentrations of potassium salts in the natural brines of some lakes in the arid and semiarid regions of the continents are also important as sources of potash; the brines of the Dead Sea in Asia Minor, the Great Salt Lake in Utah, and Searles Lake in California typify such concentrations. Every continent has major potash deposits as listed in Table 1 adopted from Cawley.1

Jan 1, 1985