Search Documents

By F. Dudouit, M. M. Mohkam, F. Renault

The Pannerdensch Kanaal Tunnel is part of Holland’s Betuweroute high speed freight railway project linking Rotterdam to inland of Europe. It comprises of twin tunnels, 1620 m long each, with 8.6 m inner diameter. The Tunnel alignment is situated mainly in sandy formations and under high hydrostatique pressure. The over burden cover varies from relatively high to very low, sometimes much smaller than the diameter. One of the special features of the Pannerdensch Kanaal Tunnel is that, over some 250 m, the twin tunnels are to be bored in a back?lled sandpit. Some 490 000cubic meter of sand has been placed and compacted by vibro-?otation to refill the sandpit. The tunneling machine is a 9.8 m slurry shield manufactured by Herrenknecht. Tunnel lining is precast concrete consisting of seven plus one key universal segments. Other than the special feature of boring through re?lled sand, constraints such a slow overburden while crossing under Pannerdensch Kanaal and some lagoons, as well as high liquifaction potential of sandy formations, render this job very unique of the type. Fine studies were conducted in heading’s stability. And, confinement pressures were determined considering different risks of liquefaction and blowout problems. Both tubes have been successfully bored. Several sections have been monitored. The results are quite interesting and in accordance with contract technical conditions.

Jan 1, 2003

By Jon Y. Kaneshiro, Gregory E. Korbin, Stephen J. Navin, Larry J. Stout

Sewage presently being discharged into the Tijuana River Valley pollutes the valley as well as the beaches in the South Bay of San Diego, making the beaches unusable nearly year round. The SBTO will convey flows down a 8.5 m (28 ft.) by 58 m (190 ft.) deep drop shaft, through a 3.35 m (11 ft.) by 5.8 km (3.6 mile) long tunnel, and up a 46 m by 2.7 m (150 ft. by 9 ft.) riser shaft connecting to a 1.5 km (0.95 mile) of seafloor pipeline and 1.2 km (0.76 mile) of diffusers on the ocean floor. The drop shaft will be sunk through 38 m (125 ft.) of saturated sands and gravels and 20 m (65 ft.) into the dense fine sands of the San Diego Formation. The tunnel liner has been designed as a five piece, single pass, gasketed, bolted, reinforced concrete liner designed to withstand an external head of 76 m (250 ft.) of water and internal operating head of up to 27 m (89 ft.) and to accommodate movement at the numerous fault crossings. The tunnel is contemplated to be driven with a state-of-the-art Earth Pressure Balance Machine (EPBM) or slurry shield machine through a wide range of conditions from clay to gravel with boulders.

Jan 1, 1995

By Elif Emil-Kaya

Samarium (Sm), as one of the rare earth elements (REEs), has gained significant attention in the production of samarium- cobalt (SmCo) magnets due to their high corrosion and oxidation resistance, as well as their high-temperature stability. SmCo magnets find applications in various industries, including but not limited to national defense, aerospace, military and medical equipment. Sm and Co have been classified as critical metals due to their economic importance and supply risk. Recovering Sm from SmCo magnets is an effective method to ensure a stable supply. The present study investigates an integrated hydrometallurgical treatment and combustion process for the preparation of rare earth oxide (Sm2O3 ) powders from SmCo. Initially, SmCo powders are exposed to nitric acid, and the resulting slurry is selectively oxidized at 250 °C to obtain Sm(NO3)3 , Co2O3 and Fe2O3 . Subsequently, the selectively oxidized powders are leached with water to extract Sm. Sm2O3 powders are produced from the obtained leaching solution using an energy- and time-efficient solution combustion process. Finally, the optimal conditions for the production of Sm2O3 are identified, and the produced powder is characterized through X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis.

Nov 1, 2024

By Barrie A. Wigmore

There are two aspects of financing western coal development -- whether there is going to be enough money to finance the prospective large development of the industry, and the specific techniques of raising money for that development. To take the first question of whether there is going to be enough money around to finance your industry, I think it is quite clear that the restrictions on the development of western coal are going to be non- financial. Environmental impact problems are creating the greatest delay in coal mine development, at the moment; but getting enough personnel, mining equipment, railroad equipment, and failure of the Department of Interior to act on leasing federal coal lands all appear likely to create significant bottle- necks in the development of western coal -- larger bottlenecks than financing. Financing appears straightforward for the industry. There are many projections of the financing required to meet Project Independence goals. The National Academy of Engineers estimated that development of 500 million tons per annum of western coal would be necessary by 1985 to meet the Project Independence goals which might require $20 billion of capital spending. It is generally agreed that 500 million tons a year is not a realistic possibility. Carl Bagge?s estimate of production of 250 million tons a year by 1983 appears a more reasonable projection. Development

Jan 1, 1976

By Richard Addison

Introduction A staccato beat rings out across the Australian bush. The stamps are at work, slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch, a tiny 22.6-t/d (25-stpd) capacity gold plant operated by the Western Australia government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory. They are miniature custom mills operated for the benefit of prospectors and small mine operators. These state batteries are so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries. They are fascinating anachronisms - throwbacks to times past, a century ago, to the hard and heady existence of gold rush days. Marvel Loch plant Typical of these operations, and perhaps a trifle more sophisticated than most, is the plant near Marvel Loch, a small center for mining and farming about 400 km (250 miles) due east of Perth. Marvel Loch. The name evokes visions of a pristine lake set in a cool, green, misty glen of the Scottish highlands. Actually, it is probably a hot, dry salt pan somewhere nearby. Just where the "loch" is difficult to discern. There is no sign of it on the map.

Jan 7, 1986

By Robert B. Gordon

The Reverse Curve Tunnel Project was located in Glenwood Canyon, Colorado approximately twelve (12) miles east of Glenwood Springs. The Project was one of many being constructed over a period of time by the State of Colorado, Department of Highways to improve Interstate 70 to four lanes as it travels thru the environmentally sensitive Glenwood Canyon. The Project consisted of excavating and concreting a tunnel approximately five hundred fifty (550) feet long, forty two (42) feet wide, and thirty two (32) feet high. The designer was Parsons, Brinkerhoff, Quade and Douglas, with geotechnical consultation provided by Woodward Clyde. CONSTRUCTION CHALLENGES There were several significant construction challenges presented primarily by the physical location of the Project. In this study each problem will be discussed, as well as how it was overcome by construction methods and/or design requirements. Portal Excavation - One of the most difficult areas of work on the Project consisted of excavation and stabilizing the East and West Portal rock prior to tunnel excavation. The Reverse Curve Tunnel passes through a sheer walled cliff face which is approximately two hundred fifty (250) feet high. Geologically the cliff consists of primarily sedimentary deposits with open, weathered joints and vertical faulting. Before the tunnel excavation could begin, a narrow sliver cut had to be excavated and rock

Jan 1, 1989

By R. W. Seedsman

Mandalong Mine was originally planned to operate with panel widths of 250 m and a predicted surface subsidence in excess of 3 m. The consent conditions applied by the NSW government on this mine plan were very tight and, following a change in ownership, were considered by the new operator to present a number of unacceptable business risks An acceptable risk profile for the mine layout restricted surface deformations to less than 500 mm vertical subsidence, less than 7 mm/m tilt, and less than 5 mm/m strain. Empirical subsidence prediction methods indicated that it would be necessary to reduce extraction panel widths of 80 m - an uneconomic option. The application of a number of rock mechanics concepts identified that the local overburden geology could be exploited such that panel widths of up to 175 m could be possible. The 125 m width was selected as a low-risk introduction of this new subsidence prediction method. The extraction of the first 2 longwall panels has demonstrated the validity of the prediction subsidence method and has provided the opportunity to refine the selection of key input parameters. The impact of mining through a zone of thrust faults was successfully predicted. The mine is now planning the introduction of 160 m wide panels, and will review the associated subsidence impacts prior to any further increases in width.

Jan 1, 2006

By J. D. Morgan

In the first half of the year, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in the second half led to the Persian Gulf War in January and February 1991. This caused an oil shock that dampened the economy. So the US gross national product rose only 0.9% to $5,463 billion (US billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The Department of Defense continued to review stockpile goals and to upgrade several mineral materials. In addition, the Bureau of Mines continued to maintain the standby Emergency Minerals Administration. The Defense Production Act, which authorizes priorities, alloca¬tions and supply expansion, lapsed on Oct. 20. So the Selective Service Act of 1967 became the authority for assuring that orders of the armed forces and defense atomic-energy programs were given priority treatment. Consumer demand strongly affects mining worldwide. US citizens carry significant debt, and large stocks of housing and consumer goods are already in place. Some 250 million persons have 188 million licensed motor vehicles and 100 million dwelling units. Consequently, new car production fell 11 %, to 6.1 million units. Truck and bus production fell 8%, to 3.7 million units and new private housing starts fell 13% to 1.2 million units.

Jan 1, 1991

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By Ron Robinson

Booster fans have been in regular use in British coal mines since the first half of this century, but a large increase in their use did not take place until after the Nationalization of coal mines in 1947. From that time the need was identified to improve standards of ventilation in general and mining engineers specializing in ventilation were appointed at all levels in the mining industry. A comprehensive approach to ventilation surveys and planning, together with the realisation of the benefits of booster fans, led to their more rapid introduction. Many coal mines in the U.K. are at moderate depth and have virgin strata temperatures of 30°C or less. The ability to control climatic conditions by increased ventilation rather than resort to cooling systems has led to the introduction of booster fans and recirculation systems in these mines. Large makes of methane and high levels of coal dust production due to increased mechanization have also required enhanced ventilation standards. This paper deals with the reasons for selecting booster fans and the specific safety considerations involved in their use. Numbers, types and sizes of booster fans in the U.K. are outlined, together with notes on installation and performance. Remote monitoring and control from the surface is dealt with, and current legislation. The evolution of controlled recirculation is also covered starting with auxiliary fan systems in 1970 and leading to very large district schemes in the late 1980s. The research at Newcastle upon Tyne University and other establishments in the climatic conditions associated with recirculation is summarised and its use in assisting existing and proposed conventional and recirculation systems is indicated.

Jan 1, 1989

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

The adsorption of gold onto activated carbon in iodide solutions has been studied. The adsorption rates were determined as a function of temperature, salt concentration and pH as well as activated carbon concentration. A kinetic model was also developed for the adsorption. The adsorption rate was believed to be controlled by a mixed mechanism of film diffusion and pore diffusion, but the film diffusion had a major contribution to the overall rate. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1993

By Chelsea Woodward

The Spokane Research Laboratory of the National Institute for Occupational Safety and Health has demonstrated a prototype hydrogen-fueled mining vehicle as an alternative to diesel equipment in underground mines. Safety and control systems were added to allow a 70-kW rubber-tired hydrogen vehicle, originally developed by the U. S. Bureau of Mines and Hydrogen Consultants, Inc. (now Hydrogen Components, Inc., of Littleton, CO), to be tested. This work began in late 2000 and culminated with a Mine Safety and Health Administration fire safety review and field tests at the Stillwater Mine in Nye, MT, in 2004.

Jan 1, 2006

The segregation process has been known for many years and applied industrially for the treatment of various refractory copper ores. The principles of the process are briefly reviewed; the process was tested in the laboratory on two copper-cobalt oxide ores from Gecamines, Shaba Province, Zaire. Various parameters of the process, such as segregation temperature, dosage of reducing and chloridizing agents and flotation conditions were inyestigated. Experimental results have shown that the segregation of copper could proceed satisfactorily at low temperature (1000° K) but that of cobalt required higher temperature and higher additions of reducing and chloridizing agents.

Jan 1, 1992

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By Austin Whillier

INTRODUCTION Use of air-cooling or refrigeration equipment in underground mines is needed when conventional ventila¬tion techniques do not maintain acceptable environ¬mental temperatures in working areas. Because refrig¬eration can be very expensive, it should be implemented only after all possible and practical steps have been taken to eliminate or reduce heat sources in the mine. As an example, to prevent the main ventilation fans from contributing heat to mine air, they should be located in the air return and not in the air intake. It is particularly important to prevent any direct contact between hot water and ventilation air, especially in mines which encounter large flows of hot fissure water. Any water hotter than the prevailing wet-bulb temperature of the ambient air must be removed by pipes located as close as possible to the water source. This hot water must not be allowed free contact with the incoming ventilation air at any time during the water's passage out of the mine. Although insulation of the pipes carrying the hot water is seldom necessary, direct contact between the air and the water must be prevented so the warm water cannot evaporate. REVIEW OF COOLING PRACTICES Spot Coolers vs. Centralized Refrigeration To eliminate a few specific hot places in an otherwise cool mine, it is possible to use devices known as "spot coolers." A typical spot cooler that uses chilled water is shown in Fig. 1. These devices consist of self-contained refrigeration units that are often mounted on rail cars for haulage to hot spots. The cooling capacities of such spot coolers usually are limited to about 100 kW or 30 "refrigeration tons." A refrigeration ton represents a cooling rate that produces 1.0 st of ice in 24 hr; that is a cooling rate of 3.517 kW (200 Btu per min). Typically, the electric-power consumption to drive the compressor motor of the refrigeration plant in mines is 1.0 kW per refrigeration ton, corresponding to a coefficient of per¬formance of about 3.5. The principal difference between spot coolers and centralized refrigeration plants is the method of re¬jecting heat from the refrigeration system. Centralized refrigeration plants always discharge heat into the reject or return airflow of the mine; often that is the primary influence in selecting the location for the underground refrigeration plant. Heat from spot coolers usually is rejected into drain water or into air that is not flowing to the location requiring the cooling. As a result, spot coolers remove heat from troublesome hot spots in the mine, injecting that heat-plus the electrical energy used by the cooling unit itself-into other working areas where the ambient conditions are cooler. In effect, this is "robbing Peter to pay Paul." In deep, extensive mines, spot coolers usually pro¬vide only temporary and, over the long term, expensive solutions to localized cooling problems. Centralized re¬frigeration plants are preferred for such mines, with cooling distributed throughout the mine as required. Fig. 2 illustrates a typical underground centralized re¬frigeration plant. Centralized plants lend themselves to improved maintenance at reduced costs while offering the economy of size. Refrigeration plants of larger unit sizes have considerably lower initial costs than smaller unit sizes. The remainder of this chapter is devoted to large refrigeration plants, with no further consideration of spot coolers. Cost of Refrigeration Total Cost: The total cost of refrigeration amounts to about $200/kW of cooling per year (1981 US $). This total cost breaks down into approximately three equal parts: 1) Financial charges, which include the interest and amortization on the capital cost of the initial installation, and the cost of necessary underground excavations. 2) Operating and maintenance costs which include the cost of the electric power to drive the refrigeration plant's compressors. 3) Distribution costs which include costs for pump¬ing, insulated piping, and air-to-water heat exchangers. The local cost of electric power, the number of operating months per year, and the method of refrigera¬tion distribution all contribute to the actual costs in¬curred in a given application. However, the variations usually are limited to no more than ±30% of the $200/ kW per year total cost figure. Cost Per Ton: Refrigeration cost per ton of mineral production can be calculated if the annual production tonnage from the refrigerated section of the mine is known. In most cases, this cost will be less than $1 .00/t. However, in deep mines with high rock temperatures, such as those found in South Africa, the total cost of refrigeration can increase to several dollars per ton of broken rock. Distribution In deep extensive mines, distributing refrigeration often accounts for about half the total cooling costs. As a result, careful consideration and planning must be

Jan 1, 1982

By Muhammad Kamran, NIAZ MUHAMMAD SHAHANI

This study elucidates a new idea to predict mine fire levels by employing several machine learning techniques. A total of 120 patterns of various mine fire influencing parameters, such as oxygen, nitrogen, carbon monoxide, and temperature, were compiled from the Adularya coal mine in Turkey. Techniques like t-distributed stochastic neighbor embedding (t-SNE) and k-means clustering were used to process the data, and support vector classification (SVC) was executed to predict various levels of the mine fire. The results revealed that the proposed model has higher credibility to predict the various levels of underground mine fires.

Feb 14, 2022

By Kenneth K. Humphreys

27.1-HISTORY, PROCESSING STATISTICS KENNETH K. HUMPHREYS 27.1.1-MINERAL PROCESSING HISTORY The processing of minerals predates recorded history. Many processing techniques have existed for thousands of years. For example, Georgius Agricola, in De Re Metallica (1556), described equipment and techniques, such as picking tables, smelting furnaces and cupolas of various types, sieves, launders. various types of crushers and grinders and other equipment, all still in use in one form or another. In translating Agricola's work into English, the late Herbert C. and Lou Hoover provided the following summary indicating the early history of particular mineral- processing operations :

Jan 1, 1973

By A. V. Castelli

Weighting materials as we know them today were first recognized in 1922 by B. K. Stroud1. Stroud, who was supervisor or the Mineral Division of the Louisiana Department of Conservation, tested galena, cement and hematite as weighting materials and successfully used hematite to make a "heavy mud". The first use of barite was in the fall of 19222 . The process of adding heavy minerals in mud was patented in 1926 by Stroud and National Pigments and Chemical Company, a subsidiary of National Lead Company now NL Industries, Inc. The ground barite was marketed as BAROIDR barite.

Jan 1, 1983

By Connor Meinke, Shaihroz Khan, Kevin Erwin, Rajiv Chandramohan, Muhammad Usman Siddiqui

High-quality sample selection for metallurgical test work is essential to a geometallurgy study, but the large multidimensional dataset makes sample selection a daunting task, as classifying the dataset while respecting its heterogeneity is difficult. This paper presents a streamlined approach for sample selection, utilizing custom-built tools in Python to standardize the methodology, saving time and costs. This approach uses the cumulative sum method, principal component analysis, and k-means clustering method to elegantly cluster the data and select representative samples. A case study is used to demonstrate the effectiveness of the methodology by selecting 40 samples for flotation test work.

Feb 1, 2024