Search Documents

By Jorgensen D. K.

The Bullfrog and Montgomery-Shoshone deposits, outside Beatty, Nevada, have a combined drill-indicated reserve of 17.4 M tons of ore with an average grade of 0.103 oz/t Au and 0.240 oz/t Ag. The deposits occur in Miocene volcanic rocks which underwent large-scale movement within a detachment-faulted terrane. The principal host to gold mineralization is a strongly welded rhyolitic tuff which experienced brittle deformation during plate movement. Open-space fractures and breccia were filled with quartz, calcite, and adularia accompanied by lesser pyrite, gold, and acanthite. Gold occurs as micron-sized particles within and adjacent to the low-angle fault and along associated listric-normal and tear faults.

Jan 1, 1989

By Joel K. Waterland

GENERAL DESCRIPTION Open cut-and-fill stoping for many years was prob¬ably the most widely used mining method in under¬ground metal mines. Then for a time this method was largely supplanted by the blasthole stope. It again be¬came popular as many mines reached depths or grades where methods requiring large open voids to remain open for extended periods of time became unsuccessful, often as a result of excessive dilution. The open cut-and-fill method is very flexible and is readily adaptable to almost any ore body. The standard application requires that a slice of ore usually 2.4 to 3 m (8 to 10 ft) thick be removed from the back of the stope, and as the ore is taken down, the back is dressed and rockbolted. After the back is secured, the broken rock is removed through rock passes to the level below. When the rock has been removed, the rock passes are extended upward the height of the ore removed, the stope is backfilled, and another cycle is mined. This method is best employed in plunging ore bod¬ies with considerable vertical extent, ore areas that re¬quire selective mining, ore areas where weak wall con¬ditions exist, and ore bodies that have an ore value that will carry this relatively expensive mining method. Blast¬hole stoping, shrinkage stoping, and other mining meth¬ods that do not employ rock passes in a stope are not efficient in plunging or flatly dipping ore bodies because the footwall makes ore removal quite difficult. Since mining is accomplished by taking down slices of the back, only small areas of the wall rock are exposed at any one time, and these only for short periods. Due to limited back height, areas of uneconomic rock may be left in place, or they may be mined and the material gobbed in the stope. Because the miners in the stope must work under freshly blasted areas, the amount of ground control is usually great. The volume of rock that is broken during one section of mining is relatively small and the amount of nonproductive work required is high. This results in limited productivity for the scope and, be¬cause of the nonproductive work that must be done on a regular basis, the production from the stope may be quite cyclical. SUITABLE ORE BODIES The open cut-and-fill method may be adapted to al¬most any type of ore body with a relatively high vertical extent. The ore body must be accessible at both top and bottom as well as at regular intervals throughout its vertical extent. Although adaptable to most ore bodies, the method is probably best employed where the ore has poor con¬tinuity and where most types of bulk mining would pro¬duce excessive dilution. In areas of poor ore continuity, the capability of continuous and extensive sampling dur¬ing the mining of each cycle makes this method very desirable. This capability also minimizes the amount of evaluation sampling that must be done before mining is started. Because of the extractive system used, the size and shape of the stope may be as readily changed as the sampling mandates. Probably the only ore characteristic demanded is that the ore has strength enough to be sup¬ported through the use of rockbolts or cable bolts dur¬ing the mining and backfilling cycles. Good planning, systematic sampling, and careful supervision will pro¬duce a product with less dilution than any other open stoping method. PLANNING Evaluation Planning Once it has been decided that the open cut-and-fill method would be the most efficient for mining a par¬ticular ore body, the next considerations would probably be the availability of an economical backfill material and the selection of an efficient transport system for this material. Although hydraulically transported mill tail¬ings are the most widely used product, this is not always practical due to mill location or the quality of the tailings. In such cases, backfilling may be used. The type of backfill and the type of equipment used will determine if a floor or capping on the backfill is required to minimize dilution during ore removal. The early selection of rock removal equipment is im¬portant since equipment usually determines the amount of development work required to bring a stope into pro¬duction and the size of the openings needed. The size and continuity of the ore body will usually determine the type of loading equipment. The use of slushers or load¬haul-dump (LHD) equipment captive in the stopes will minimize the amount of development. If the ore con¬tinuity is such that a ramp system for extraction can be used, the cost of development will be increased but the flexibility of continuous mining will minimize the cycli¬cal nature of the production. The height of the mining section usually is deter¬mined by the strength of the wall rock and the amount of back bolting required. Once this has been decided, the appropriate drilling equipment can be chosen. The number and sizes of the rock passes employed depends upon the type and size of the extractive equipment and the type of backfill that is to be used. Since the miners must enter and leave the stope each shift, the level inter¬val is usually maintained at approximately 45 m (150 ft). Access from the level above into the stope must be main¬tained at all times. The employees perform all the work in the stope and adequate ventilation must be provided. Stope Planning Due to the flexibility of the method and the vari¬ability of the ore zones, layout is usually done on a stope basis. In areas where continuity is a problem, the size of the stope is usually determined by the boundary of the ore (with all of the ore within that boundary being removed). In areas of good continuity where ramps are to be used, the length of the stope may be determined by the length of time each of the cycles (preparation, back¬fill, mining, and ore extraction) requires. The ramp work is then laid out so that access to the various parts

Jan 1, 1982

By N. Arbiter

Introduction The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter (L/D) ratio. This is in spite of the fact that practice varies substantially: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia, and historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills, on the occurrence of the overload phenomenon, and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape factor is of major importance in this area and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type. Dimensionality in mill design Ball mill shape factors in the period prior to 1927 (Taggart, 1927) averaged 1.1/1 for 29 center discharge mills and 1.0/1 for 30 peripheral discharge mills. With the resumption of new plant construction after the 1930s depression, the Morenci concentrator continued the 1/1 ratio with its 3.1 x 3.1 m (10 x 10 ft) mills. The ratio was increased progressively from then on, reaching 1.6 and 1.8/1 for the largest overflow mills currently. As shown recently (Arbiter, 1989), this is in sharp contrast to autogenous and SAG mill shapes, for which the ratio averages 0.4 in North America. On the other hand, South African practice, starting at the turn of the century with autogenous mills having 4/1 ratios, moved toward 1/1 until recently, when a 2.5/ 1 ratio mill was installed. The reasons given for such divergent practice for mill shape factors are in some respects contradictory and generally inconclusive. The most complete discussion from a practical viewpoint (Dor and Bassarear, 1982) is limited to primary SAG and autogenous mills. Considerations of ball mill dimensionality have had a twofold direction. On the one hand, it has been argued that ball mill efficiencies should increase with increasing diameter and that the specific energy for a particular grind should be reduced accordingly. An inadvertent test of this idea at the Bougainville operation (Burns and Erskine, 1983) resulted in drastic underpowering, which led to failure to reach design capacity until additional mills were installed. This can be taken as strong evidence against any increase in efficiency with diameter. In another direction, it has been argued (Arbiter and Harris, 1982, 1983) that there is a limit to ball mill diameters because of the demonstrable limit to axial flow velocities evident in the overload phenomenon, which as a fact is incontrovertible. But that it places a limit on mill diameters overlooks the evidence given below that appropriate variation in the L/D ratio will permit major increases in diameter, limited only by constructional or economic factors. The present study was directed toward quantifying the overload phenomenon through examination of the influence of mill dimensionality variation and mill operating variables on its occurrence. It is shown that varying the operating conditions, specifically the load fraction and the fraction critical speed, can reduce the risk of overload for existing operations; while appropriate decreases in the L/D ratio can minimize the risk in the design of new circuits. Ball mill overload Ball mill overload is a consequence of the approach to a critical velocity with increasing feed rates or circulating loads. Although the effect has been known for over 50 years, there have been no previous attempts to quantify it. The following description of the ball mill as a flow system is the preliminary to a quantitative analysis: 1) In the absence of a ball load, axial flow of pulp through a mill resembles open channel flow, except for disturbances near the shell due to shell/lifter rotation. 2) For a given ball load (Lf), the void fraction available for pulp hold-up (H) for the ascending portion of the load is approximately 0.4 Lf. In the descending portion, it is greater than this and increases with fraction critical speed (Fc) because of load expansion. 3) Increasing the feed rate increases pulp hold-up and progressively fills the available void space. At a critical flow rate, which depends on system geometry, hydraulic head and pulp rheology, void filling reaches its limit; a pool forms rapidly and fills available space outside the ball load and up to the overflow level. Prior to this, pulp discharges mainly along the ascending rim of the overflow. 4) For a small mill (Lo et al., 1990), it has been shown that with increasing feed rates the critical filling is at or near 50% of the mill volume. Power drops rapidly when this level is reached, as required by the torque formula. 5) The transition to overload is associated with the following phenomena: a) The decrease in power draw. b) Damping of mill sound. c) Reduced comminution of coarser feed sizes, probably due to reduced direct impact in the presence of a pool. d) Increased circulating loads, which further intensify the overload, and increased density of cyclone underflows, which can lead to roping. e) Conditions beyond overload are not known because feed rates are not delibelrately increased beyond this point. f) The existence of the phenomenon limits the capacity of a mill with a fixed set of operating conditions and can prevent the balancing of hard ore feed rate decreases by increases in soft ore rates.

Jan 1, 1992

By Rolf Pollak, Jan Tegtrneier, Gerhard Keller, Horst Gerhardt, Wolfgang Müller, Dieter Tetzner

INTRODUCTION Under certain geological and mining conditions mining near the surface results in an intensive destruction of the overlying rock strata. If the system of mine openings remains filled with air after having completed all mining activities because the flooding of the mines depending on the morphology of the mining area does not exceed a certain level, this circumstance might result in dangers for the public. This is particularly true where uncontrollable air- ways occur within the destroyed rock or if former uranium mining areas are concerned. In these areas radon emanation resulting in undue radon concentration should be taken into account. This circumstance can be counteracted by suitable measures of ventilation. In the following the example of a uranium deposit in the Erzgebirge Mountains (Saxon Ore Mountains) is used to illustrate how statements about the ground flow through overlying rock can be made on the basis of systematic investigations. Finally comparisons with experience gained in coal mining yield orientation data which are used as input quantities in ventilation network calculations and in project preparation of mine fans. Last not least it is proved that endangering the population by radon can be excluded by installing an appropriate fan. INITIAL SITUATION From 1946 to 1989 the uranium deposit of Schlemal-Alberode was mined starting from superficial zones down to depths of 1,800 m. The total output amounted to 80,000 t of uranium, i.e. Schlemal Alberode is one of the largest uranium deposits in the world. The mine openings comprise a cavity of 40 million m3. Al- though thin seams (0.2 to 0.3 m) and steep to semi-steep veins (60 - 70 degrees on average) were extracted using the method of overhand cut-and-fill there were also deposit sections with larger thicknesses and poor ore zones, respectively, where especially after the war until about 1955 large openings were formed due to missing filling. Due to this uncontrolled, relatively "wild" mining considerable subsidence of the surface and fractures in the border zone of the subsidence area occurred. The town of Oberschlema was destroyed and an area of 0.14 km2 was damaged by mining involving a maximum subsidence of 6 m in the centre - called deformation area. The rehabilitation work for the deposit area of Schlemal Alberode involves the flooding of the openings up to a level of the Markus-Semmler-Sohle as long-term preventive measure. Fig. 1 shows the flooding level of October 1996. The level of the -540 m drift will probably be reached in June 1997. From that point of time a general rearrangement of the ventilation has to be made because the central return air ventilation via shaft 373 will no longer be possible. This shaft has no connection with the superficia1 system of mine openings. A new return air ventilation system based on shaft 382 as return air shaft will be designed (Fig. 1). The capacity of the future mine fan system will e.g. be determined by the flow conditions in the deformation area mentioned above. For this reason investigations were carried out in a test drift 13a on the level of the Markus-Semmler-Sohle in the stretching zone of the subsidence trough for several days (Fig. 2 and 3). INFLUENCE OF THE OPERATING CONDITIONS OF THE MAIN MINE FAN ON THE RADIATION SITUATION ON SURFACE The beginning of flooding in 1991 was also the beginning of the investigations into the options of future ventilation due to the reduction of the mining area. The first analyses of radon emanation made in May 1991 showed that only about 20 % of the total radon emanation result from systematically ventilated mine workings. This means that despite of existing dams the air streams through the majority of mine openings of the deposit. The analysis of the individual radon inflows illustrates the special problematic nature of the deposit involving all possible effects on the surface. The shutdown of the main mine fan over the long period between 2.10. and 6.10.1991 showed the essential influence of the operating conditions of the fans on the whole radiation situation on surface. Fig. 4 shows the comparison of the radon concentration level and its daughters during a 'normal" weekend with the level during long-term shutdown in the old 'Casino" of the papermill of Niederschlema. This papermill as well as the 'Casino" are situated in the outcropping zone of the deposit section of Niederschlema. The -60 m level was driven as the upper level in this area, from which the panels were driven to about 20 m below the surface. Also below the "Casino" there is such a panel in the vein 'Glirck", whose roof is directly situated below the building in a depth of 39 m. Directly next to it there is the raise 2 of the panel 'Namenlos" in a depth of 27 m. The graphics clearly shows the immediate increase in radon concentration as well as in the daughter concentration after the shutdown of the fans. The elimination of the artificially generated negative pressure results in the reversal of the convection direction due to the natural ventilating pressure. The interface structure allows the mine airto pass through aero- dynamic connections to the surface. Neglecting the meteorological parameters the concentrations of radon and its daughters in- creased by about 350 % as compared to a 'normal" weekend during longterm shutdown (i.e. in 4 days). Furthermore it could be noticed that a stationary state between the radon and its daughters has not been established in the period

Jan 1, 1997

By B. Elevli

Production scheduling of an open-pit mine is one of the most important steps in open-pit mining. The production schedule of a mine defines the distribution of cash flows and as a result directly influences the net present value (NPV) and overall economic feasibility of a project. Although the need to plan and operate a mine with an optimum production schedule has been obvious for some time, the methods used to obtain such a schedule have not been. The current practice for doing is to do it by hand on the basis of trial and error analysis. In an attempt to improve the way production scheduling is currently done, a new computer based production scheduling algorithm is developed. This paper describes the fundamentals of this newly developed heuristic scheduling algorithm and its application on a gold deposit. The results coming from a case study show that the schedules based on the new method provides improved cash flows compare to a manually done production schedules.

Jan 1, 1989

By Dennis P. Bryan

Natural lightweight aggregate may be defined as inherently low density natural mineral materials. In most all instances they are relatively young volcanic rocks which, because of their geologic environment, are limited to the Western U.S. These Tertiary and Quaternary volcanics are low-density glass and vesicular material including, but not limited to, pumice and volcanic cinder. The distribution is widespread throughout the West with the principal producers being New Mexico, California, Oregon, Idaho and Arizona. The primary user is the construction industry where weight reduction equates to cost savings. Principal products in which natural lightweight aggregate is utilized because of its lower density include lightweight portland cement concrete and lightweight concrete masonry units. In addition, due to location, some natural lightweights compete with normal weight constructions aggregates for uses such as road base and common backfill material.

Jan 1, 1989

By K. Tokutake

Kobe Steel, Ltd. improved the quality of iron ore pellets for blast furnace burdens when it enlarged its blast furnaces. However. there still remained room to increase reducibility at high temperatures for better blast furnace operation. In particular, it was still necessary to lessen the reduction retardation above 1200?C. In the last few years, by employing iron ore and additives of optimum size structure, large pore pellets with a high porosity have been obtained. By using this method. Kobe Steel. Ltd. has accomplished the technology to produce pellets with remarkably high reducibility.

Jan 1, 1989

By Cleophus Short

[Of the many occupations in and about the coal mines, those of the haulage crews are among the most hazardous. Statistics ship that the second greatest number of fatalities about the coal mines occur during haulage ion and through the use or misuse of haulage equipment. During the five year period between January 1, 1957 and January 1, 1962, the m stone mine had a. Sack haulage frequency of 4098 and mined 3, 541,939 toads per haulage fatality. Coal mire haulage is similar in respects to railroading. We gee very serious consideration to the instillation of tack and to the selection of the haulage crews. In doing this, we are attempting to have our coal mine haulage as. Safe as that of the railroads.]

Jan 1, 1963

By H. W. Peirce

Arizona is a sun-belt growth-region where 13 tons of industrial (nonmetallic) minerals is being produced annually per capita. In 19B5, non-fuel mineral production reached $1.532 billion and consisted of metallic ($1.277 billion-84%) and nonmetallic ($253.5 million-16%) earth materials. Sand-and-gravel value was second only to copper. over 90% of the value of nonmetallics is represented by combined sand, gravel, cement, and lime. The remaining less than 10% ($25 million) was attributed mainly to stone, specific volcanic products (cinder, perlite, pumice), gypsum, clays, salt, zeolite, and others. Current interest in industrial-mineral development in Arizona is high, especially in the geologically complex Basin and Range region.

Jan 1, 1988

By D. C. White

The Vulture Mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11,000 kg Au and 8,000 kg Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely disseminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence all dipping north about 35°. Early mining focused on the vein-hosted gold particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pitting of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry.

Jan 1, 1988

By C. J. Johnson

As the U.S. coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 80% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1988

By Y. H. Kim

A simulation procedure has been developed that realistically portrays aggregate growth and disintegration for particular types of floc structures in water and wastewater treatment processes. The procedure requires local dissipation rates and specification of an interaction distance between colliding particles. A principal difficulty encountered in polymer flocculation, however, arises from changes in conformation of adsorbed macromolecules. Therefore, in systems where polymer flocculation occurs by bridging, dynamic changes in the particle size distribution depend upon the interaction of nonlinear. stochastic hydrodynamics with particles whose growth results from a number of concurrent and sequential random processes.

Jan 1, 1988

By A. M. Stone

Following the conceptual idea of a Continuous Elution Process early in 1982, the system was successfully pilot plant tested at Western Mining's Kambalda gold plant in December 1982. As a consequence of these tests the Ok Tedi elution ciruit design was changed from batch operation to continuous operation resulting in a reduction in the number of similarly sized elution columns from five operating with one standby to one operating with one standby and halving the process steam requirements. In addition to providing significant capital and operating cost savings the continuous process was simpler to operate than the batch process.

Jan 1, 1989

By Harold B. Goldman

On the basis of tonnage, the sand and gravel industry is the second largest nonfuel mineral industry in the United States. In 1990, the production of sand and gravel was 927 Mt valued at $3.4 billion. California, which leads the nation with more than 126 Mt, together with Texas, Washington, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 Sieve (0.074 mm openings) to those passing a No. 4 Sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see chapter on Industrial Sand and Sandstone and Glass Raw Materials). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material that is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Sand and gravel is also used as construction fill, road base and subbase, and decorative material. Portland Cement Concrete Aggregates: Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15 to 20% water, 7 to 14% cement, and66 to 78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman and Reining, 1983). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate: Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.076 mm), uniformly coated and mixed with asphalt produced in the refining of petroleum. Sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement aggregate. GEOLOGY General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles that are sound and durable. Soundness and durability are terms used to denote the ability of aggregates to retain a uniform physical and chemical state over a long period of time so as not to disintegrate when exposed to weathering and other destructive processes. Individual particles must be tough and firm, possessing the strength to resist physical stresses and chemical and physical changes, that may cause swelling, cracking, softening, and leaching. The aggregate should not be contaminated by excessive clayey material, silt, mica, organic matter, chemical salts, and surface coatings. Physical Properties: The quality of aggregate depends upon its physical and chemical properties. These, in turn, may be inherent mineralogical and textural features of the rock or may be the effects of later changes such as tectonics, mechanical or chemical weathering, or incrustations. The physical properties most significant for concrete use are: 1) abundance and nature of fractures and pores, 2) particle shape and surface texture, and 3) volume changes which may occur because of freezing and thawing or wetting and drying. An aggregate is considered to be physically sound if it is adequately strong and capable of resisting the agencies of weathering without disruption or decomposition. Minerals or rock particles that are physically weak, extremely water absorptive, and easily cleavable are susceptible to breakdown. The use of such materials in concrete reduces strength or leads to early deterioration by promoting weak bond between cement and aggregate, or by inducing cracking, spalling, or popouts. Severely weathered, soft, micaceous, or porous materials may cause localized stresses to develop in concrete by swelling and shrinking during wetting and drying or freezing and thawing cycles. Physical Suitability of the Various Rock Types. Sedimentary rocks have a wide range in physical and chemical qualities. Sand- stones and limestones, if hard and dense, are ordinarily satisfactory, but many sandstones are friable and excessively porous and commonly are clay-bearing. Shales generally make poor aggregate material, being soft, weak, and absorptive. Most igneous rocks are satisfactory, being normally hard, tough, and dense. Tuffs and certain flow rocks may be extremely porous and have high water absorption and low strength. Metamorphic rocks differ in character. Most quartzites are massive, tough, and dense. Fine-grained marbles are usually durable, but coarse-grained marbles have low abrasion resistance. Gneisses are ordinarily very tough and durable. Some schists contain micaceous minerals that are undesirable because they are soft, laminated, and absorptive. Micaceous minerals are susceptible to splitting along cleavage planes and thereby impair particle strength and durability. Some schists and slates in particular are thinly laminated and tend to assume flat slabby shapes that lack strength-and do not pack well. Any or all of these rock types may be rendered undesirable because of harmful exterior coatings. Weathering processes, particularly the action of ground waters, deposit these coatings. The most common coatings are calcium carbonate, clay, silt, opal, chalcedony, iron oxide, manganese oxide, and gypsum. Particles with these coatings are undesirable as aggregates because the bond between particle and coating may be weak, and decreasing the strength of the aggregate-cement bond.

Jan 1, 1994

By W. K. Fletcher

As part of an ongoing programme on behaviour of heavy minerals In streams, the dispersion of Au as free gold (Day and Fletcher, 1987), Sn in cassiterite (Fletcher et al, 1987) and W in scheelite (Saxby and Fletcher, 1987) have been investigated downstream of mineralization. The studies of Au and W were undertaken, in British Columbia and the Yukon Territory, respectively, in streams that are strongly influenced by spring snowmelt floods. Sn was investigated under tropical rainforest conditions in Peninnsular Malaysia.

Jan 1, 1988

By S. Horton, F. L. Stanley, P. J. Bethell

Introduction The McClure River Processing Plant is located at McClure in Dickenson County, VA. The plant was originally constructed in 1979 as a 600 st per hour facility. The plant is fed by coals from numerous mines in the area as well as a major longwall mine onsite. Coal is processed predominantly for the metallurgical coal market. The original plant was comprised of three separate processing circuits incorporating a heavy medium vessel for the coarse material (+10 mm). Intermediate sized material (10 x 0.6 mm) was beneficiated in heavy medium cyclones, with the remaining fines (0.6 mm x 0) passing to froth flotation for upgrading. The products from all three circuits were combined prior to thermal drying and then stored in silos or ground storage prior to shipment to the metallurgical coal markets. A middlings heavy medium cyclone circuit was also present to rewash the vessel and primary heavy medium cyclone rejects. The original circuit is as shown as Fig. 1 (Editor's note: All figures are reproduced at the end of this paper.) In reasonably close proximity to the McClure Plant is the much older, less efficient Moss 1 Plant, (Chance cone, table, water only cyclone, froth flotation, Fig. 2), which prior to the McClure Plant expansion was processing considerable tonnages of coal. At that time, the McClure River Plant was processing coal at the maximum possible feed rate, and the Moss 1 Plant was finding increasing difficulty in maintaining the stringent quality specifications on its major metallurgical coal accounts. Given the fact that many of the feeder coals to Moss 1 could be moved with minimal difficulty and cost to McClure, an exercise was conducted to evaluate the potential of expanding the McClure Plant. This would result in transferring coals from Moss 1, thereby increasing yield, reducing operating costs, and enabling customer specifications to be met more easily. After evaluating many possible ways of expanding the McClure Plant, we eventually settled on an approach based on the idea of Gallagher at German Creek in Australia (Gallagher, 1986). Our objective was to increase plant capacity by removing the coarser size fractions (0.60 x 0.15 mm) from froth flotation and at the same time eliminating the finer fractions (1.25 x 0.6 mm) from the heavy medium cyclone circuit, thereby allowing these circuits and therefore the plant as a whole to increase its capacity. These size fractions (0.60 x 0.15 mm from froth flotation and 1.25 x 0.6 mm from the heavy medium cyclone circuit) would be treated in a new spiral circuit. After desired evaluation of the various circuit capacities, including desliming screen, clean coal filter and thermal dryer capacities, etc., it was concluded that we should be able to maintain high levels of processing efficiency in the existing circuitry while at the same time expanding plant feed rate from a nominal 600 st per hour to 1000 st per hour, thereby achieving the objectives The circuit that was finally settled on is shown in Fig. 2. Several unique features were incorporated in this circuit in an attempt to maximize processing efficiency and reduce maintenance costs. First, the idea of a single-stage spiral circuit was abandoned in favor of a two-stage circuit incorporating rewashing the primary spiral middlings in a secondary spiral (Bethell, 88). The spirals selected were Mineral Deposits Model LD4 units. It was felt, after much previous testing, that spiral middlings rather than being a true middling gravity fraction were in fact a combination of true middlings with a preponderance of misplaced light coal and high-density rock. Consequently the insertion of this material directly into either clean coal or refuse streams (per normal practice) would only lead to loss of efficiency. The operating philosophy behind the design of the circuit was to produce the purest coal and rejects possible by adjusting the spiral splitters. Misplacement of refuse into the clean coal and vice versa would be minimized by taking a fairly large middlings cut. By reprocessing this material (10%-15% of primary spiral feed) in a secondary bank of spirals the misplaced material in the primary middlings would be reprocessed and its probability of reporting to the correct stream greatly enhanced. To minimize fines loading on the spirals, fine aperture sieve bends were to be included. A further novel feature of the circuitry is the desliming/ dewatering system. A philosophy of accepting inefficiency but forcing it to work in our favor was developed. The dewatering screens (Linatex Combis) were chosen not for their ultimate screening efficiency but for their ability to remove slimes (tolerating a fair quantity of oversize in the effluent) and their enhanced maintenance characteristics. Any oversize passing into the effluent, together with the fine coal centrifuge effluent, would pass to classifying cyclones, the objective of which was to reject to overflow (and hence froth flotation) as many fines as possible (-150 µm) without running the risk of losing coarse (1.25 x 0.15 mm) material to oversize. Hence, by a process of producing a "slime free" screen product coupled with a "coarse free" cyclone overflow, sizing efficiency could be maximized. Obviously, recirculating load had to be factored into the Combi Screen design capacity. The spiral circuit as shown in Fig. 2 was installed at McClure River in January 1988. The spiral circuit efficiency was very high immediately, and, after the normal debugging, plant capacity has been increased to the point at which we are currently processing of the order of 1100 st per hour. Test program The performance of the spiral circuit has been evaluated by two major samplings of the entire new circuit, coupled with routine bi-monthly tests on all other major components of the plant circuitry.

Jan 1, 1992

By K. A. Sauer

Blasting can create severe interference for a mine's carbon monoxide based fire detection system. At the present time, without being able to differentiate between blast and non-blast carbon monoxide, a fire detection system must either set fairly high alarm levels for its sensors, or allow frequent "false" alarms to sound during blasting. This paper will introduce current work being done which will attempt to define characteristics of the carbon monoxide concentrations time curve for blasting. The work uses drift blasting for its data base as it is one of the more common forms of blasting. Future work with the data may produce a mathematical model which can be used to monitor and identify the carbon monoxide time curve for drift blasting.

Jan 1, 1989

By Fred N. Kissell, George H. Jr. Schnakenberg

INTRODUCTION A variety of instruments are available for measuring or monitoring the performance of underground mine-ventilation systems. In general terms, the instruments may be classified as those that measure air velocity and those that measure gaseous concentrations. All costs herein are in terms of 1978 US dollars. The mention of a specific manufacturer or device is not intended to be an endorsement by the US Bureau of Mines. AIR-VELOCITY INSTRUMENTS The basic instruments used for measuring the air velocity in mines are the vane anemometer and the smoke tube. Vane Anemometer Of the air-velocity instruments, the 102-mm (4.0¬in.) vane anemometer is the most common and is available as either a low- or high-speed type. The low-speed anemometer generally is the most suitable for measuring the velocities in ordinary airways. For a rough check of the velocity in an airway, it usually is satisfactory to hold the anemometer by hand, positioning it in the center of the airway for 30 sec. However, the resultant error may be as high as 25% , and such a hand-held approach is unsuitable when accurate or reliable measurements are required. To obtain more accurate measurements, the proper procedure is as follows: 1) Since holding the anemometer by hand generally causes the instrument to read about 15% high, it is mounted on a 0.6-m (2-ft) extension rod. 2) The airway is divided into equal right and left halves. A 1-min traverse is used in each half, moving the anemometer smoothly up and down in a zigzag pattern so that the entire half is covered within the allotted minute. 3) The manufacturer's correction table is applied to the readings to adjust the velocity calculation as necessary. Whenever possible, anemometer readings should be obtained in a long straight section of airway that has a constant cross-sectional area. Bends and obstructions should be avoided, since they cause turbulence and other discontinuities in the airflow and can degrade the accuracy of the velocity measurements. Although a series of velocity measurements at one location usually corresponds to within a few percent, this is not an indication that the airflows calculated from those readings are completely accurate. One reason is that the correction table provided with the instrument generally is not for that specific instrument; instead, it represents the average correction for all such instru¬ments made by the particular manufacturer. Most cor¬rection tables specify a correction factor of from 0 to 15%, depending upon the velocity. However, even after correction, the instrument error still may range from 3 to 5%. At low velocities such as those below 0.76 m/s (150 fpm), the instrument error can be two or three times greater than this, ranging from 6 to 15%. The new ball-bearing anemometers generally perform somewhat better at low velocities than did the older conventional anemometers. Another source of error is introduced when measur¬ing the cross-sectional area of the airway or entry. Under the best of circumstances, measurement errors, instrument errors, and a host of other minor errors all combine to cause a total error of at least 10% in the velocity calculation. The vane anemometer also can be used with reason¬able accuracy to measure airflows in mine-ventilation ducts. In this application, the anemometer is mounted on a rod and is held at the center of the duct end. For a duct that is discharging air, the average velocity in the duct is 85% of the centerline reading (Northover, 1957). For a duct that is taking in air, the average velocity is 70% of the centerline reading (Haney and Hlavsa, 1976). To measure the airflow discharged from a regulator or from a small hole in a stopping or bulk¬head, a correction factor for the area is necessary. A good approach in this situation is to traverse the area of the regulator or hole, holding the anemometer with an extension rod. This provides an average velocity that is multiplied by 85% of the measured area of the regulator or hole. In all cases, the manufacturer's instrument cor¬rection table must be used and applied properly. For accurate results, the anemometer should be returned to the manufacturer for periodic cleaning and checking. If it is in daily use, the anemometer should be returned about once per year, and proportionally less frequently if the usage is less frequent than on a daily basis. Smoke Tube The smoke tube may not appeal to individuals who believe that good measurement results can be obtained only with expensive, complicated, and fragile instru¬mentation. Nevertheless, smoke works about as well as anything for the routine measurement of low air velocities in mines. The following procedure yields reasonably good results: 1) Two marks are scratched 7.6 m (25 ft) apart on the floor of the airway. 2) The smoke tube is used to release a cloud of smoke in the center of the airway, about 0.9 m (3 ft) upstream of the first mark on the floor. 3) A timed interval begins when the leading edge of the smoke cloud passes over the first mark, and the interval stops when the leading edge of the cloud passes over the second mark. 4) A factor of 20% is subtracted from the cal¬culated velocity to determine the true average velocity, providing a correction for the centerline and for the spreading effect at the front of the cloud. Velocities calculated with the preceding method generally are accurate to within 10 to 15%. In some instances, the cloud from a conventional smoke tube

Jan 1, 1982

By Yuanhong Qi, KUN CUI, Tao Fu, XUNFU WANG, Yingyi Zhang, Jie Wang, Junmao Qie

Indonesia is the world’s largest supplier of nickel ore, with its nickel laterite resources mainly distributed in the Moluccas and Sulawesi regions. However, there is scant research on the mineralogical characteristics of nickel laterite deposited in southeast Sulawesi, Indonesia. This study aims to investigate the mineral phase structure, chemical analysis, thermal properties and element distribution characteristics of the middle and lower part of the rotten rock zone located in the southeast Sulawesi ophiolite belt.

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010