Search Documents

By A. E. Lewis, J. Du Plessis, J. Chivavava

Current metallurgical processes lack selective and efficient REE recovery from aqueous leach liquors. Antisolvent crystallisation is used to selectively recover pure inorganic salts from aqueous solutions without excessive chemical use in ambient conditions. Yttrium sulfate octahydrate (Y2(SO4)3.8H2O) was used as a representative rare earth salt to investigate the effect of antisolvent selection on the crystal morphology and size distribution of the final crystalline product produced through antisolvent crystallisation. The antisolvents of choice were short length alcohols that are water miscible i.e. methanol, ethanol, 2-propanol and t-butanol. All experimental parameters except the type of antisolvent were kept constant under isothermal conditions. The large reduction in solubility of the salt by the antisolvent creates high supersaturations. This leads to high product yields as observed in this study at > 91%. In general, a variety of morphologies were successfully formed in each individual alcohol including; rods, plates, prismatic cubes and starburst clusters. The powder X-ray diffraction (XRD) analysis indicated that Y2(SO4)3.8H2O was the only species present for all final products. There was a change observed from the starburst and rod structures for the shorter alcohols towards prismatic cubes for the longer alcohols due to different strengths in the solute-antisolvent interaction at the crystal growth faces. The crystal sizes increased with an increase in the alcohol chain length because of the lower supersaturation conditions due to a limit in the mass transfer induced by the bulkier alcohol structure. In conclusion, it has been shown that the particle morphology and size can be greatly affected by the selection of antisolvent even under high supersaturation conditions, contributing to understanding the effect of different antisolvents on the final particle characteristics. The engineering of favoured product characteristics can therefore be achieved by antisolvent crystallisation, presenting a viable alternative process for the recovery of REE. Keywords: Antisolvent crystallisation, rare earth elements, morphology, particle size

Jan 1, 2020

By F. K. Mulenga, M. Lusambo

"Geometallurgical models are a strategic tool used primarily in planning, diagnosis, and process optimisation. This paper discusses the development of a predictive model for flotation recovery at Kansanshi concentrator in Zambia as a function of key operational parameters. Daily data for milling and flotation from the circuit processing the copper sulphide ore was analysed. This data, recorded over a period of one year of production, was collected from diverse sensors measuring semi-autogenous milling and flotation parameters. Statistical analysis showed that copper head grade, acid-insoluble, and acid-soluble copper, SAG mill throughput, ball mill load, and tonnage of feed material to the SAG mill in the -125 +63 mm size fraction contributed to the prediction power of the proposed empirical model by as much as 90%. Finally, a proposal was made for the development of a simulation model under MODSIM®, a flexible tool for mineral processing applications. This was to test the limitations of the empirical model for future refinement. IntroductionKansanshi is the largest copper mine in Africa and the world’s eighth largest copper producer, with a total of 253 272 t of copper produced in 2016 (Newall, 2017). It is located approximately 10 km north of Solwezi, the capital and administrative headquarters of the North Western Province, Republic of Zambia. The ore deposit consists predominantly of chalcopyrite and malachite with variable amounts of chalcocite, bornite, chrysocolla, and azurite. Because of the varying proportions of sulphide and oxide copper minerals, the ore is classified into three distinct categories: sulphide, mixed, and oxide ores. As such, three separate processing circuits are used to mill the ore down to a standard targeted grind size of 80% passing 150 µm before froth flotation and leaching.A lot of research and development has been done to improve the performance of the sulphide ore circuit at Kansanshi. Despite the research efforts and subsequent operation, the sulphide ore circuit did not attain the target recovery and grade for 2016, primarily because of the complexity of the orebody.The constant drive to achieve the set production target of recovery and concentration grade after froth flotation motivated the development of a tool for the prediction of recovery. The anticipated benefit is not only to enable the plant to apply corrective actions when needed, but also to make a tool available for the quick assessment of the plant performance of the. For that purpose, data spanning June 2016 to May 2017 was analysed, cleaned up and curvefitted to an empirical model. In doing so, key parameters were determined and calibrated to represent the behaviour of the plant."

Nov 1, 2018

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By S. C. Maji, U. S. Chattopadyay, S. Chaudhuri, T. Gouri Charan

India is devoid of coking coal resources, which is a vital raw material for coke making. As a result it has to import about 80% coking coal for steel making. Indian National Steel Policy, 2017 has envisaged crude steel production around 300 million tonnes Mt) by the year 2030-31 and forecasts coking coal demand of 161 Mtpa (million tonnes per annum). One way of improving the indigenous resources is to study the performance of existing washeries and to improve the clean coal recovery by adopting suitable technology. A study was carried out, mainly to focus on the fine coal circuit of an existing coking coal washery, to generate the desired quality of clean coal. The operating coking coal washery being studied is presently feeding coal from nine different sources with varying feed ash contents. The coal fines varied in ash content ranging from 19.5% - 43.6%. For treating the coal fines, the washery has operated a spiral for the past few years. Performance studies were carried out, and it was found that the spiral is not efficient in recovering the cleans. Detailed investigations were carried out on the coal fines using flotation techniques, and it was found that to achieve a low ash clean coal, the froth flotation is a much better beneficiation option than a spiral, The studies showed that the recovery of clean coal through a spiral is 67.7% at ash content of 27.0%, while flotation tests showed a recovery of 68.1% at 16.5% ash content. Keywords: Coking coal washery, near gravity material, spiral washer, froth flotation

Jan 1, 2020

By R. Xie, J. Liu, Y. Zhu, Y. Li

The surface chemistry features of spodumene and feldspar were investigated by XPS, zeta potential measurements and first principle calculation. The results indicated that the zeta potential of feldspar was more negative than that of spodumene. The most possible active sites on spodumene and feldspar were Al sites and O sites. However, the number, type and activity of these sites were different. The flotation behaviour of five new collectors (cationic collector decyloxy-propyl-amine (DPA), anionic collector α-bromododecanoic acid (α-BDDA), N-Dodecyliminodiacetic acid (DIDA), and mixed collector DPA-BDDA and DPA-DIDA) were investigated through micro flotation experiments and analysed based on the surface chemistry features of spodumene and feldspar. The results revealed that cationic collector DPA processed a high collecting capacity for both minerals. The highest recovery of spodumene and feldspar was 91.60% and 95.30% respectively. The anionic collector α-BDDA and DIDA showed poor flotation behaviour. The recovery of spodumene and feldspar when using α-BDDA as collector was less than 5% and when using DIDA as collector was less than 1%. For the mixed collector DPA-BDDA, the recovery of spodumene and feldspar was 82.27% and 32.61% respectively at pH 4.5. For mixed collector DPA-DIDA, the recovery of spodumene and feldspar was 35.69% and 9.08% respectively at pH 5.8. The results indicated that the cationic collector had high collecting capacity, but low selectivity. The collecting capacity of anionic collector for spodumene and feldspar was poor at the same concentration compared with cationic collectors. Mixed collector DPA-BDDA showed good flotation behaviour and selectivity on spodumene. The ―COO- in mixed collector might improve the selectivity. However, too much ―COO- would increase the electrostatic repulsion, which might cause low selectively and poor recovery. Keywords: Spodumene, feldspar, surface chemistry features, mixed collector, flotation

Jan 1, 2020

By G. Raspa

The paper describes a computer procedure for evaluating and selecting recoverable reserves in a mine worked by sublevel stoping. The boundaries of the volume to be mined are optimally defined by means of the 3-dimensional Lerchs-Grossmann algorithm, separately applied to both sides of the panels. The procedure, which has been developed for Masua Mine (Sardinia), also provides for smoothing the optimized boundaries, positioning the drilling drifts, interactive design of drilling fans and calculation of tonnage and grade of each volley. These tonnages and grades form the input of another procedure evolved for production planning.

Jan 1, 1987

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By Milton Syamujulu

In 1994, Nkana smelter commissioned a Multimillion US$ Dollar Chilean Teniente converter (CT) in its operations in order to improve its smelting technological base. The main objective was to reduce the overall smelting energy costs and increase the sulfur capture for sulphuric acid production to support the company?s leaching operations at Nchanga Tailings Leach Plant. A decade of CT operations have since ensured following its installation and startup. This paper provides a Technical and Operational Audit of the performance of the CT in the first 10 years of its operations at Nkana smelter.

Jan 1, 2005

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By M. Loots, E. Van Der Lingen, S. Grobbelaar

The increased adoption of unmanned aerial vehicles (UAVs) may improve the productivity and costeffectiveness of remote sensing in the mining industry. This review’s objective is to enable stakeholders to identify possible application adoption, improvement, and innovation opportunities. The review merges a building block strategy and practical screening criteria to identify possible avenues of research to answer the review questions. After the screening process, 72 documents were included in the review. Papers were classified into four categories: exploration, development, exploitation, and reclamation. Fifteen applications were identified, the majority of which were in the exploration phase. The most often researched applications were topographic surveys, reclamation monitoring, and slope management. From the two UAV types identified, multi-rotor vehicles were the most favoured for all applications. From the eight remote sensing techniques identified, photogrammetry was the one most often used. Other techniques were limited because of complexity, cost, or the incompatibility of sensors and UAVs. The review was limited to published papers in academic journals. Future studies could aim to include empirical data on the latest UAV applications used in the mining industry.

Jul 2, 2022

By M. B. Shongwe, G. Freemantle, M. Botha, S. Brill, J. D. Steenkamp

During steelmaking, one important factor for production efficiency is the free opening of the ladle nozzle during continuous casting. Free opening occurs when the well filler sand and the steel flow freely when the slide gate is opened. Well filler sands are used for the slide gate of a ladle to separate the slide gate refractory and the molten steel. The well filler sand is partially sintered by the heat of the molten metal, which can result in the ladle nozzle failing to open if the sand is not sintered to an appropriate extent. It is therefore of great importance that the sintering behaviour of well filler sand is understood. We studied the effect of the well filler sand chemistry on its sintering properties. Samples of well filler sand with various chemical compositions were sintered in a high-temperature chamber furnace. Quantitative X-ray diffraction (XRD), inductively coupled plasma optical emission spectrometry (ICPOES), and wavelength dispersive spectrometry (WDS) by electron microprobe analysis (EMPA) were used to analyse the various well filler sand mixes. Points of analysis were indicated on backscattered electron (BSE) micrographs. Quantitative element mapping was undertaken by energy dispersive spectrometry (EDS). Thermodynamic calculations in FactSage predicted the percentage liquid phase present for the various well filler sand compositions at equilibrium conditions. The results of this work show that the degree of sintering of chromite-silica well filler sand depends strongly on the silica content. The amount of liquid phase formed increases with increasing silica content.

Feb 2, 2022

By Q. G. Reynolds

The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single-electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions?this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magnetohydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By L. Dison

There are many potential uses in gold mining for an initially stiff element of backfill that will yield at a predetermined load and maintain that load to beyond a compression of 30%. Such elements could be used as yielding rib pillars, as replacements for more conventional supporting packs, as con- fining bulkheads for mass backfill, as supports to provide lateral constraint, and load-carrying augmentation to overloaded rock pillars. The paper describes a system of reinforced cemented backfill that can be used to provide the above requirements. The necessary characteristics of the reinforcing and the cemented tailings are described together with the method of design to obtain a predetermined stiffness and yield load. The load-compression characteristics of the reinforced tailings elements are described and the effect of changing various of the design parameters is demonstrated.

Jan 1, 1988

By K. Lomberg

In this paper the process of sampling and assaying as it relates in particular to the platinum group elements (PGEs) is presented. A discussion of the geology of PGE deposits is included to provide an understanding of the mineralization that is considered necessary prior to sampling, as this has a direct bearing on the mineral resource estimate and also the selection of an appropriate mining cut. The discussion includes the selection of the sampling technique (drilling or face sampling), the size of the sample relating to the requirements of the laboratory, the potential mining cut, as well as a reference to sampling theory. The selection of an assay technique that is appropriate and will yield the optimal result based on sample turnaround, precision, accuracy, and cost is then considered. Examples are drawn from work undertaken on the Bushveld Complex (Merensky Reef, UG2 Chromitite Layer, Platreef) and Great Dyke (Main Sulphide Zone). A discussion of the appropriate QA/QC programme includes the chain of custody, CRM selection and the QA/QC process. Keywords sampling, assaying, QA/QC, platinum group elements.

Jan 1, 2014

By S. Özgen

In this study, the possibility of beneficiation of chromite tailings in the Uckopru/Fethiye-Turkey region by a combination of hydrocyclone and multigravity separator (MGS) was investigated. The two significant operational parameters of hydrocyclone, which were diameter of the apex and diameter of the vortex, and the three significant operational parameters of the MGS, which were drum speed, tilt angle, and wash water, were varied and the results were evaluated with the central composite rotatable design. In order to produce a chromite concentrate by hydrocyclone and MGS, mathematical model equations were derived by computer simulation programming, applying the least-squares method using Minitab 15. Second-order response functions were produced for the grade and recovery of chromite concentrates.

Jan 1, 2012

By P. K. Van Manen

Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province in South Africa. A single 168 MVA six-in-line rectangular furnace smelts dry concentrates containing platinum group metals (PGMs). Furnace energy consumption since commissioning is presented, showing that energy efficiency improves as capacity utilization increases. An energy balance for the furnace is outlined, indicating the measured or calculated energy losses from the hearth and side-wall cooling, the copper coolers, the upper furnace walls and roof, and the energy losses in off-gas, matte, and slag. From the energy balance, the potential to improve energy efficiency by controlling the slag temperature, the slag level, and the off-gas volume is derived. Furthermore, the impact on the energy balance of different concentrate types is discussed, as well as the potential impact of replacing all upper waffle coolers by plate cooler panels.

Jan 1, 2009

By C. A. Rawlins

Deep underground mines use refrigeration systems to provide a reasonably comfortable ambient environment to increase productivity and to maintain safety as a priority. Deep level gold mines maintain the environment at an acceptable temperature, i.e. 27°C. However, the increasing cost of doing so through refrigeration is becoming a significant factor in the economic viability of mines. This paper discusses of the important facet of energy losses in cooling reticulation systems, laying with the specific emphasis on the subject of chilled water transport pipe insulation and its thermo-dynamic relationships. Aspects relating to the deterioration of open cell-type insulation materials such as polyurethane/styrene foams and the use of Phenolic resins that have good fire retardation properties have been investigated. The thermal conductivities of these insulation media are good (meaning below 0.05 W/°C)However, they are known to be negatively influenced by water vapour ingress and vapour pressure differences that result in the ingress of water into the material by means of absorption, condensation, hygrospicity, permeability and capillary action, to name a few of many. The overall effect on mine cooling efficiency takes in the two forms: first by the loss of refrigeration or increased chill in the water temperature arriving in a given section and second, by a loss in transfer efficiency when the gap between the arriving water temperature and the actual air temperature decreases. Keywords: Conductivity, vapour, insulation, fluid, thermal, temperature, pressure, transport, refrigeration.

Jan 1, 2007

By W. C. Joughin

A risk evaluation model has been developed, that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment. This enables the comparison of different support systems based on the expected frequency of injuries and the total cost of the support system, including the expected economic losses. The model takes into consideration the variability in joint orientations and joint strength within the geotechnical environment and the variability and quality of support systems. The quantification of the benefits of other rockfall risk-mitigating strategies, such as the effectiveness of barring or monitoring, are also incorporated in the model. The risk model is described in this paper and the validation of the model and case studies are described in Part II.

Jan 1, 2012

By A. M. Bauristhene

Ti-64, which accounts for more than 50% of the worldwide titanium tonnage, has found commercial importance in industries requiring components with high specific strength and resistance to corrosion. Investment casting is the preferred production method due to the difficult machinability of the alloy. This study was aimed at investigating the mechanism and the extent of alpha case formation on Ti-64 components cast using the investment casting method with YFSZ (yttria fully-stabilized zirconia) shell moulds after vacuum induction melting. The extent of the reaction between the mould hot face and the molten metal has been studied by varying parameters such as soaking temperature and mould hot face composition, and examining their effects on the reaction with the mould. An increase in the soaking temperature had an effect on the alpha case, both in appearance and hardness, but had no effect on contamination levels by carbon, oxygen, and nitrogen. The depth of alpha case increased with soaking temperature, increasing from 35 µm to 161 µm with an increase in temperature from 1200°C to 1400°C. The micro-hardness profiles provided insight into the effect of the alpha case on the mechanical properties of the Ti-64 alloy by displaying hardness values of 1000 HV0.1 and above, but could not be solely utilized to determine the alpha case penetration depth due to microstructural differences in the unaffected Ti-64, in particular the martensitic microstructure that formed with a fast cooling rate from a higher temperature. Levels of expected contaminants such as Zr, Y, 0, and C were low. The addition of the colloidal zirconia binder affected the interfacial reactions. YFSZ proved to be a thermodynamically stable refractory material, with the alpha case possibly forming as a result of segregation.

Jan 1, 2013

By A. F. Mulaba-Bafubiandi

Pseudomonas spp was isolated from mine water and tailings samples collected from mining effluents and mine dumps in the Gauteng and Northern provinces of South Africa respectively. Adsorption properties of Pseudomonas spp were then tested for the removal of Cu and Co initially from their synthetic sulphate solutions, subsequently from effluents derived from metallurgical operations. The effects of experimental conditions such as pH, temperature, time, volume and metal concentration on the efficiency of the biosorption process were studied. Absorption of 45% Cu (pH 6, 37°C, 24 hours) and 40% Co (pH 6, 37°C, 24 hours) was observed from solutions with low concentrations (0.07 M). A maximum of 73% and 65% of Cu and Corespectively were recovered from the mine water samples derived from effluents.

Jan 1, 2009