Search Documents

By J. N. Van der Merwe, D. P. Roberts

The two components of pillar design formula being used in South Africa are pillar strength and pillar load. While considerable effort has been directed to the determination of pillar strength, the other half of the safety factor equation, the load, has not received the same amount of attention. The load acting on pillars has always been calculated using the Tributary Area Theory (TAT). This paper summarises the recent studies on coal pillar loading using various numerical models. It concludes that although there are meaningful differences under certain circumstances, there is still a compelling argument to use the TAT in coal pillar design. Les deux parties composantes de la formule de conception de pilier généralement utilisée en Afrique du Sud sont la résistance de pilier et la charge de pilier. Tandis que des efforts considérables on été dirigés vers la détermination de la résistance de pilier, l’autre moitié du facteur de sécurité n’a pas reçu la même attention. La charge agissant sur les piliers a toujours été calculée avec la Théorie d’Aire Tributaire (TAT). L’étude présente résume les études récentes sur la charge de pilier de charbon utilisant des modèles numériques variés. La conclusion est que bien qu’il y ait des différences significatives selon les circonstances, il y a toujours un argument puissant pour utiliser le TAT dans la conception de pilier de charbon. Die in Südafrika für die Auslegung von Pfeilern verwendeten zwei Formelkomponenten sind Pfeilerstärke und Pfeilerbelastung. Während beträchtlicher Aufwand zur Bestimmung der Pfeilerstärke gemacht wurde, wurde der anderen Hälfte der Sicherheitsfaktorsgleichung nicht die gleiche Aufmerksamkeit gewidmet. Die auf die Pfeiler wirkende Last wurde immer unter Verwendung der Tributary Area Theory (TAT) berechnet. Diese Arbeit fast neuere Studien betreffend der Belastung von Kohlepfeilern unter Verwendung verschiedener numerischer Modelle zusammen. Die Schlussfolderung ist, daß obwohl unter bestimmten Vorraussetzungen bedeutende Unterschiede existieren, nach wie vor ein bezwingendes Argument besteht TAT in der Kohlepfeilerauslegung zu verwenden.

Jan 1, 2003

By M. Hakala

A computer program was developed to simulate transient strains and stresses during an overcoring in the situ stress measurement. The solution is based on superpositioning of elastic stresses. The measured strains can be compared with the calculated ones to check if the measured transient behaviour is accordant with the interpreted in situ state of stress. If not, the in situ state of stress can be calculated based on any transient or final strain values. The transient stresses can be compared with the strength envelope of intact rock and thereby estimate the core damage potential. Technically, the developed code fulfilled all the objectives, and the numerical error was found to be less than 5%. The basic idea can be applied also for different overcoring probes with minor modifications and recalculation of stress tensors. The analysed case studies showed clearly the advance of having an objective and practical quality control method to study the reliability of the in situ stress measurement data. The study was set up and funded by the nuclear waste management companies Posiva Oy ( Finland ) and Svensk Kärnbränslehantering AB ( Sweden ). Un programme informatique a été développé pour simuler des tensions et des contraintes passagères pendant la mesure in situ de contrainte de surcarottage. La solution se fonde sur une superposition de contraintes élastiques. Les contraintes mesurées peuvent être comparées avec celles calculées pour vérifier si le comportement passager mesuré correspond à l'état de contrainte in situ interprété. Sinon, l'état de contrainte in situ peut être calculé à partir de n'importe quelle valeur de contrainte passagère ou finale. Les contraintes passagères peuvent être comparées avec l'enveloppe de force de roche intacte et ainsi il est possible d'évaluer le potentiel de dégâts au noyau. Techniquement le code développé a rempli tous les objectifs, et le taux d'erreur s'est révélé être inférieur à 5 %. L'idée de base peut être appliquée aussi pour différentes expériences de surcarottage avec des modifications mineures et le recalcul de tenseurs de contrainte. Les études de cas analysées ont montré clairement l'avantage d'avoir une méthode de contrôle de qualité objective et pratique pour étudier la fiabilité de données de mesure de contrainte in situ. L'étude a été fondée et financée par les sociétés de gestion de déchets nucléaires Posiva Oy (Finlande) et Svensk Kärnbränslehantering AB (Suède). Es wurde ein Computerprogramm entwickelt, um Transient-Beanspruchungen und Spannungen während eines Überentkernens in situ-Spannung-Messung zu simulieren. Die Lösung beruht auf Superpositionierung von elastischen Spannungen. Die gemessenen Beanspruchungen können mit den berechneten Daten verglichen werden, um nachzuprüfen, ob das abgemessene Transient-Verhalten mit dem interpretierten in situ-Zustand der Spannung übereinstimmt. Wenn nicht, kann der situ-Zustand der Spannung auf irgendwelchen Transient- oder endgültigen Beanspruchungswerten berechnet werden. Die Transiet-Spannungen können mit dem Stärke-Umschlag des intakten Felsens verglichen werden und dadurch ein Kernbeschädigungspotential kalkulieren. Technisch erkannte der entwickelte Code alle Ziele und hat gefunden, dass die numerische Fehler weniger als 5 % waren. Grundsätzlich können auch verschiedene Überentkernen-Untersuchungen mit kleineren Modifizierungen und Wiederberechnung des Spannung-Tensors angewandt werden. Die analysierten Fallstudien zeigten deutlich den Fortschritt, objektive und praktische Qualitätskontrollmethode zu haben, die Zuverlässigkeit in Situ-Spannung-Messung-Daten zu studieren. Die Studie wurde aufgestellt und durch Atommüll-Management-Firmen Posiva Oy (Finnland) und Svensk Kärnbränslehantering AB (Schweden) finanziert.

Jan 1, 2003

By Y. Y. Jiao, J. G. Cai

To investigate the dimensional effect on shock wave propagation in jointed rock masses, a 2-D and a 3-D calculation of a site test are performed respectively by using Discrete Element Method, the simulated results are compared with test data. It shows that, in modelling shock wave propagation and attenuation in jointed rock masses, when the explosive along explosion chamber is long enough and the joints are dense enough or uniformly distributed, the model can be considered as plane-strain problem, 2-D results are good enough to fit with test data. 2-D modelling, with much more details of rock masses taken into account, can be applied to make critical engineering judgements instead of 3-D modelling in some cases.

Jan 1, 2003

By W. Zhu

ABSTRACT: This paper presents further developments of the principle of Construction Process Mechanics of rockmasses, The principle of loading variations analyses in space-time is systematically described. To demonstrate the applicability of the theory and method, the effect of the construction process of two practical engineering cases are analysed. ZUSAMMENFASSUNG: Das Mechaniksprinzip vom Konstruktionsprozess des Massenfels wird in diesem Aufsatz weiter Entwickelt.. Das Prinzip von Variationsladungsanalyse mit dem Zeit-Raumseffekt wird systematisch erklaert. Um die Anwendungsmoeglichkeit der Theorie und der Methode zu anschaulich darstellen, das Mechanikseffekt des Konstruktionsprozess wird fuer zwei praktische Anwendungsbeispielen zergliedert. : RESUME: Dans ce papier le development se fait pour principles de la mechanique de process de construction . Le principle de variable analyse considerant effet de temps et de Space est present ´e . Pour demonstrer l´appilicabilite de le theorie et la methode , l´èffect de processe de construction pour ce deax examples sont analysés .

Jan 1, 2003

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely: codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage like nuclear power generation where international cooperation is eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit their mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2003

By D. G. Hulbert, D. J. Oosthuizen, D. de V. van der Spuy

Expert Online, as a software system, is aimed at providing plant operators in the minerals industry with effective training and on-the-job assistance. It incorporates a number of features to achieve this goal, of which the most important is its ability to explain the dynamics of the plant and control system in simple language, mimicking an informed plant expert who has online access to the inner workings of the plant and control system. This is made possible by a novel form of Artificial Intelligence, called the Interpreting Expert System. Previous implementations of the IES were only capable of explaining controller actions. Expert Online will extend this capability to also perform the more difficult task of explaining process behaviour. Expert Online will implement three main processes, namely the accumulation of data from the controllers and plant models, the interpretation, processing and filtering of that data and lastly communicating the relevant information to the user, both as written messages and in other audio-visual forms. Although Expert Online is aimed at the operator, other plant personnel, like supervisors and plant managers, will also benefit from it. This paper focuses on the structural and functional design of Expert Online for implementation on the latest version of Mintek’s open control platform, PlantStar, highlighting advances and additions since the previous implementations of the Interpreting Expert System and concluding with an example illustrating some of the principles.

Jan 1, 2003

By A. Rejeb

ABSTRACT: This paper contributes to the study of underground structures in argillaceous media, especially Tournemire argillites (Aveyron, France). The basic results obtained over six years in two experimental drifts at the Tournemire site are presented. In situ measurements cover drift wall temperature, humidity and convergence. Delayed convergence represents around 50-65% of the total measured convergence. Analysis of the measurements has shown that delayed convergence is explained by the viscoplastic behaviour of the argillaceous formations. Lemaitre’s rheological model has been extended to the orthotropic case, as Tournemire argillite is naturally anisotropic. The triaxial creep test results on samples at different orientations enabled the parameters of the Tournemire argillite to be identified in terms of orthotropic viscoplastic law. A plane deformation model, using this rheological law and the initial stress field in the site, was developed to interpret the convergence measurements in the drifts. The computed results match the measurements well, especially during the excavation phase. KEY WORDS: Argillite, convergence, time-dependent behaviour, creep, viscoplasticity, modelling. ZUSAMMENFASSUNG: Der vorliegende Artikel ist ein Beitrag zur Untersuchung der unterirdischen Strukturen tonhaltiger Milieus, insbesondere der Tongesteine von Tournemire (Aveyron, Frankreich). Die wichtigsten Ergebnisse, die in zwei Forschungsstrecken am Standort Tournemine über einen Beobachtungszeitraum von sechs Jahren zusammengetragen wurden, werden hier vorgestellt. Gemessen wurden in situ Temperatur, Feuchtigkeit und Streckenkonvergenz. Von der insgesamt gemessenen Konvergenz sind etwa 50 bis 65 % auf zeitlich verzögerte Konvergenz zurückzuführen. Die Auswertung aller Messungen hat ergeben, dass die zeitverzögerte Konvergenz mit dem viskos-plastischen Verhalten des Tonsteinmassivs zu erklären ist. Aufgrund der naturgemäßen Anisotropie des Tongesteins von Tournemine wurde das rheologische Modell von Lemaitre auf den orthotropen Fall ausgedehnt. Triaxiale Kriechversuche bei jeweils unterschiedlicher Ausrichtung dienten der Ermittlung der einzelnen Parameter des orthotropen, viskos-plastischen Gesetzes. Zur Auswertung der Konvergenzmessungen innerhalb der beiden Strecken wurde unter Beachtung dieses rheologischen Modells sowie des ursprünglichen Spannungszustands vor Ort ein flächiges Deformationsmodell entwickelt. Die Rechenergebnisse zeigen eine gute Übereinstimmung mit den Messungen, insbesondere während der Vortriebsphase. SCHLÜSSELWÖRTER: Tongestein, Konvergenz, zeitlich verzögertes Verhalten, Kriechen, Viskoplastizität, Modellbildung. RESUME : Cet article est une contribution à l’étude des structures souterraines dans les milieux argileux, notamment les argilites de Tournemire (Aveyron, France). Les principaux résultats obtenus pendant six années, dans deux galeries d’expérimentation au site de Tournemire, sont présentés. Ces mesures portent sur la température, l’humidité et la convergence des parements des galeries. La convergence différée représente environ 50 à 65% de la convergence totale mesurée. L’analyse de l’ensemble des mesures a montré que la convergence différée est interprétée par le comportement viscoplastique du massif argileux. Etant donné que l’argilite de Tournemire est naturellement anisotrope, le modèle rhéologique de Lemaitre a été étendu au cas orthotrope. Les résultats des essais de fluage triaxial, sur des échantillons à différentes orientations, ont permis de déterminer les paramètres de la loi viscoplastique orthotrope. Un modèle en déformation plane, utilisant cette loi rhéologique et l’état de contrainte initiale dans le site, a été développé en vue d’interpréter les mesures de convergence dans les galeries. Les résultats des calculs sont en bon accord avec les mesures et plus particulièrement durant la phase de creusement. MOTS-CLEFS : argilite, convergence, comportement différé, fluage, viscoplasticité, modélisation.

Jan 1, 2003

By S. K. Gilman, V. E. Hugo

A common problem encountered in the mineral sands industry is that the mineralogical measurements used in defining the resource are not readily converted to metallurgical recoveries, which are used to predict the quantity of the final products. The problem stems from the different objectives of the exploration and metallurgical assessment programmes, and is often compounded by the use of different laboratory techniques and mineral definitions. Common mistakes include the misapplication of routine analysis, incorrect interpretation of mineral recovery, the confusion of mineral recovery with product yield and inconsistent definition of the same mineral. Experience has shown that unless these potential mistakes are identified, the measurement techniques used during exploration and metallurgical assessment are not compatible, often resulting in large errors in the prediction of mineral production. There are no easy solutions to the problem, as there is no universal assay technique which can cost effectively characterize all the mineral sands resources. The recommended course of action will therefore require several iterations to optimize the assay technique to suit the resource. Fundamental to the success of the measurement technique is the understanding of the mineralogy, its behaviour during mineral processing and the quality requirements for the final products.

Jan 1, 2003

By J. F. Shao, G. Duveau, W. Z. Chen, O. Ozanam

In this paper, we present a sensitivity study for the numerical modelling of hydromechanical coupling around a shaft in partially saturated claystone. Two representative constitutive models have been used: an elastoplastic damage model (IDEPLML) and an elastic perfect plastic model based on the Hoek and Brown failure criterion (H&B). A series of comparative studies have been performed with respect to main parameters involved in coupling process (mechanical, hydraulic and hydric properties). The emphasis is put on the evaluation of induced plastic, damaged and failed zone due to excavation and drying process. Dans ce papier, nous présentons une étude numérique paramétrique du comportement hydromécanique couplé d’une argilite partiellement saturé, lors du creusement et de la maintenance d’un puit L’étude paramétrique porte à la fois sur le type de modèle et sur les principaux paramètres (mécaniques hydrauliques et hydriques) intervenant dans le couplage. L’accent est principalement porté sur l’évaluation des zones plastifiées autour de l’ouvrage lors de la désaturation. In unserem Beitrag geht es um eine digitale parametrische Untersuchung über das hydromechanische Verhalten eines teilweise durchtränkten Tons beim Abteufen und dem Betrieb von Schächten. Die parametrische Analyse konzentriert sich auf den Modelltypus und auf die wesentlichen bei der Verbindung wirksamen Parameter, d.h. die mechanischen, hydraulischen und hydrologischen. Der Schwerpunkt liegt auf der Bewährung der plastifizierten Bereiche des Bauwerkes während der Austrocknung.

Jan 1, 2003

By R. Strydom, J. H. Selby

Published information is available on the radiological impacts of disposing of zircon sand in a landfill. Zircon flour by virtue of its finer particle size presents a different set of issues during disposal. This paper describes two options for disposal of such fine grained materials – namely incorporation into concrete aggregates and agglomeration by addition of cement. The study considers the radiological exposure of the public from such disposal methods and concludes that these options are viable alternatives for the safe disposal of waste zircon flour. The disposal of zircon into concrete aggregates at a rate of 10 per cent produces a sufficiently low effect to allow such aggregates to be used in building foundations or other such mass concrete applications. The use of cement agglomeration methods will also provide a safe method of landfill disposal provided at least 20 cm of soil cover is included.

Jan 1, 2003

By E. M. Bloomfield, C. A. Jermy

Geotechnical tests were carried out within an area of the coastal sand dune cordon of northern KwaZulu-Natal which is currently being exploited through mining of heavy mineral sands. In situ and laboratory tests were carried out to assess the density, strength and stability of the dune sand material before and after mining. The most stable combination of sand (>63µm) and fines(<63µm) material was determined as well as the effects of compaction on the strength and permeability of the sand dune samples. In situ DCP and density tests showed that the sand dunes fall in density immediately after mining has taken place. However, settlement of the dunes occurs with time and the density increases within the top 2 metres, and particularly once the dunes become re-vegetated. Laboratory tests carried out showed that the dune sand with between 20% and 30% added fines had the highest shear strength and dry density, but the permeability was shown to decrease steadily with increasing fines up to 40% fines added. The addition of fines would result in steadily increasing water flow problems. Compaction of the dune sands was shown to significantly increase the density and the shear strength, but with a corresponding dramatic decrease in the permeability of the material. Slope stability analysis carried out on models of the dunes with increasing fines showed that the addition of fines increases the stability of the dune sands up to a peak of about 30% fines added, and compaction further increases the stability of the dune sands. Despite the benefits of compaction on the stability of the tailings dunes, the loss of permeability is thought to outweigh the benefits as well as the high costs involved. The stability of the tailings dunes greatly increases after re-vegetation. Compaction and densification of the tailings dunes may be necessary within the top 2 m interval if large-scale construction takes place on the sand dunes. Petrographic analysis was performed to understand the granular interactions of the sand and fines fractions, and the effect of the in situ weathering of the dune sands on the stability of the sand dunes. As the fines contents increase the gaps between the sand grains are filled, until a point where the percentage of fines begins to push the sand grains apart.

Jan 1, 2003

By W. Dziurzynski

Transient states of the air parameters in mine workings occur as the effects of natural and technological disturbances, and in particular as a result of changes in ventilation conditions, caused by alteration of the mine workings geometry, state of fans performance or emission of gases. Particularly significant are those transient states caused by disturbances resulted from catastrophes, since they are frequently associated with violent phenomena that may be a danger for life and health of the staff working underground. The paper presents a number of examples of transient states of the air parameters in mine workings after a catastrophe, like the bump in the ZABRZE-BIELSZOWICE coal mine. Registration of air disturbances by the monitoring systems of ventilation in mine workings in the area of disaster both at the moment of a catastrophe occurrence and later during the rescue operation, enabled to track out the incident and identify the circumstances and reasons of those tragic events which caused death of 18 miners during last two years. Furthermore, computer simulations of processes occurring in mine ventilation network make effective research tools to be applied in practice, among others for the study of accidents and disasters.

Jan 1, 2003

By T. Oberthür

The Great Dyke of Zimbabwe constitutes the world?s second largest reserve of platinum group elements (PGE) after the Bushveld Complex in neighbouring South Africa. Within the Great Dyke, economic concentrations of PGE are restricted to sulphide disseminations of the Main Sulphide Zone (MSZ), which are currently mined at the Ngezi, Unki, and Mimosa mines. Near-surface oxidized MSZ ores have a large potential. Their total resources are in the range of ca. 160 ? 250 Mt; however, all previous attempts to extract the PGE from this ore type proved uneconomic due to low PGE recoveries (<< 50 per cent) achieved by conventional metallurgical methods. Within the ores of pristine, sulphide-bearing MSZ, the PGE are bimodally distributed. Platinum occurs mainly in the form of discrete platinum group mineral (PGM) grains (mainly bismuthotellurides, sulphides, and arsenides), whereas approximately 80 per cent of the Pd (and some Rh) is hosted in pentlandite. Within the oxidized MSZ ores, the PGE are polymodally distributed. Whereas arsenide- and sulphide-PGMs, making up ca. 25 per cent of the original Pt content of the ore, largely remain stable (relict PGMs), the remaining PGMs are disintegrated. The base metal sulphides are destroyed, partly releasing their base metal and PGE contents, and are replaced by iron oxides or hydroxides. Unspecified amounts of the PGE are redistributed and either form secondary PGMs, are found in chemically and mineralogically ill-defined (Pt/Pd)-oxides or hydroxides, or in iron-hydroxides, Mn?Co-hydroxides, and in secondary silicates. The problematic processing of oxidized MSZ ores is attributable to their complex nature and polymodal distribution of the PGE, prohibiting a significant upgrading of the ores by conventional metallurgical methods. Therefore, only bulk leaching methods are viable for ore treatment, and novel metallurgical methods have to be developed for the processing of these ores. Our ongoing work aims at locating the PGE in their mineralogical form in order to understand the mineralogical balance of the PGE in the ores and thereby facilitate the evaluation of metallurgical options for their recovery. A short overview on options and recent advances regarding the recovery of the PGE from oxidized ores is given.

Jan 1, 2012

By J. W. Latilla, J. J. van Wijk

A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. Une cassure de taille en avant des unités de soutènement s’est produise sur la veine numéro 4 dans le puits numéro 3 (Matla 3) de la mine Matla Coal en avril et mai 2002. Les conditions d’extraction étaient extrêmement difficiles sur une distance d’environ 150 m dans la voie de tête et, en moindre mesure, sur le front de taille lui-même. L’étude présente analyse les raison majeures pour les conditions de grandes contraintes qui ont conduit à la cassure de taille, à savoir l’existence d’un mur de dolérite de >20m proche de la surface et l’effet d’arrêter la longue taille sur la veine 5 superposée. Les difficultés rencontrées pendant la cassure de taille sont rapportées, y compris les effondrements de piliers et toit dans la voie de tête, les aires de grandes contraintes en avant du front de taille causant des problèmes de stabilité pour le toit et les parois latérales, l’injection de roches cassées dans la taille en voie de tête, les cassures secondaires à mi-taille, et la disponibilité d’unités de soutènement critiques. Interventions minières réussies et leçons apprises furent : un angle de remblai de 14.6° était plus réaliste que celui de 20 à 25° utilisé auparavant pour prédire la conduite du mur de dolérite dans cet endroit ; tir à deux temps du mur a réduit considérablement les contraintes sur la taille et la voie de tête, ce qui a permis un travail de support complémentaire ; des types variés de support de piliers furent analysés et évalués ; la nécessité d’avoir toujours une trousse de première urgence disponible fut reconnue ; et finalement une stratégie pour les panneaux en dessous du mur fut

Jan 1, 2003

By T. A. Ngcobo

Paper written on project work carried out in partial fulfilment of BSc Eng (Mining)degree The purpose of this report is to assess the risks faced by mines in dolomitic compartments in particular Kloof 8 shaft. The dolomites of the West Rand comprise one of South Africa?s most natural water resources, and overlie the reefs of the richest gold mines in the world. The pumping of water from the dolomitic aquifers to prevent flooding has caused the natural water table to subside, and the resulting cavities within the dolomite rock formations that overlie many gold deposits sometimes collapse, causing sinkholes. These impacts of the mining industry could worsen over time if preventative measures are not taken. This report discusses these impacts in detail, more specifically the risks to which operations in dolomitic compartments are exposed. A risk analysis was carried out to access the risks that the organization could face and it was this analysis that allowed one to examine the best methods to combat the problems. Other factors such as geological features and seismic events were also considered for the evaluation. To aid with the completion of this work various resources were utilized. A literature study was undertaken, information was gathered from various experts who specialize in dolomitic studies, evaluations were conducted and conclusions reached. The results from the project indicated that preventative measures should be implemented and correct procedures put in place to prevent any disasters.

Jan 1, 2006

By J. P. Harrison

ABSTRACT: The significant effect of fracture surface morphology on the mechanical behaviour of rock masses is well known and has been studied by many people. For linear profiles taken from fracture surfaces, short- and long-period variation has traditionally been described using the descriptors ‘roughness’ and ‘waviness’, with Fourier series analysis being perhaps the most commonly used technique to distinguish between the two attributes. However, the mathematical procedure is involved and the assumptions that have to be made may not be appropriate for rock fracture surfaces. In this paper, an alternative method is presented that enables us to distinguish between roughness and waviness of a linear profile by performing only one straightforward analysis. In our technique, surface morphology is studied in terms of the distribution of unit normal vectors to the profile. The statistical analysis of the distribution is performed using Riemannian, rather than the customary Euclidean, geometry, and from this the 1D Riemannian dispersion parameter (DR1) is obtained, which quantifies the geometry of the profile. The method is applied at different scales to both synthetic sinusoidal profiles and real rock profiles. The results show how periodic behaviour of the profile is revealed at scales where DR1 is substantially equal to zero. RESUME: L’influence significative de la morphologie des épontes sur le comportement mécanique des massifs rocheux est bien connue et a fait l’objet de nombreuses études. Pour les profils lineraires, les variations de courtes et longues périodes sont traditionnellement décrites par les indicateurs “rugosité” et “ondulation” qui sont le plus couramment distingués à l’aide d’une analyse en series de Fourrier. Cependant, la méthode de calcul utilisée et les hypothèses faites ne sont pas appropriées dans le cas des épontes rocheuses. Cet article présente une méthode alternative qui permet de distinguer la rugosité de l’ondulation d’un profil en réalisant une seule analyse directe. Avec notre technique, la morphologie de l’éponte est étudiée comme une distribution spatiale de vecteurs normaux au profil. L’analyse de cette distribution est réalisée à l’aide de la géométrie Riemannienne plutôt que la géométrie classique Euclidienne et permet d’identifier la dispersion Riemanienne en 1D (DR1) qui quantifie la géométrie du profil. Cette méthode est appliquée à différentes échelles sur des profils artificiels sinusoïdaux et des épontes naturelles. Les résultats montrent que le comportement périodique du profil est révélé à des échelles où DR1 est essentiellement égal à zéro. ZUSAMMENFASSUNG: Der signifikante Effekt von Bruchoberflaechen Morphologien auf das mechanische Verhalten von Gesteinsmassen ist gut bekannt und von vielen Bearbeitern untersucht worden. Traditionel lineare Profile von Bruchflaechen sind mit kurz und lang periodischen Variationen, die auch als “Rauhigkeit” und “Welligkeit” bezeichnet worden sind, beschrieben worden. Hierbei ist wohl die Fourier Serien Analyse das wichtigste Hilfsmittel zur Unterscheidung der beiden Attribute gewesen. Hierfuer wird jedoch ein mathematisches Prozedere verlangt und Vorraussetzungen gemacht, die vielleicht nicht fuer Gesteinsbruchflaechen zutreffend sind. In dieser Publikation wird eine andere Methode vorgestellt, die uns mit Hilfe nur einer einfachen Analyse erlaubt zwischen “Rauigkeit” und “Welligkeit” bei einem linearen Profil zu unterscheiden. In unserer Methode wird die Gesteinsoberflaeche unter zu Hilfenahme der Verteilung von Einheitsnormalvektoren beschrieben. Die statistische Analyse der raeumlichenVerteilung dieser Vektoren wird mit Hilfe der Riemannschen, anstatt der ueblicherweise benutzten Euklidischen, Geometrie durchgefuehrt. Von ihr wird der Riemannsche Dispersions Parameter (DR1) abgeleitet, der die Geometrie des Profils quantifiziert. Diese Methode ist bei verschiedenen Masstaeben sowohl auf rein harmonische (sinusoidale), syntetische Profile als auch auf Gesteinsprofile angewendet worden. Die Ergebnisse zeigen, dass bei Masstaeben bei denen DR1 nahe Null ist periodische Characteristika der Profile hervortreten.

Jan 1, 2003

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 um. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By V. Labiouse, B. Heidenreich

The rebound phenomenon, which occurs during rockfalls when a rock block impacts with a slope surface, is influenced by several parameters related not only to the slope material but also to the block and the kinematics. The paper presents a small-scale testing campaign undertaken at the LMR (EPFL) to better understand and quantify the bouncing of blocks on granular slopes. The influence of some factors related to the ground material, the block and the kinematics is examined. Bei Steinschlägen wird die Flugbahn eines stürzenden Felsbrockens maßgeblich durch den Abprall vom Hang bestimmt. Der Rückprall hängt von verschiedenen Parametern ab, wobei nicht nur das Hangmaterial sondern auch Blockeigenschaften und Kinematik eine große Rolle spielen. Zum besseren Verständnis dieses Phänomens und seiner Quantifizierung werden am LMR (EPFL) kleinmaßstäbliche Versuchskampagnen auf granulären Materialien durchgeführt. Der vorliegende Artikel stellt die Versuche vor und untersucht den Einfluss verschiedener Boden-, Block- und kinematischer Parameter. Le phénomène de rebond qui se présente lors de l’impact d’un bloc rocheux sur la surface d’un versant dépend non seulement des caractéristiques du terrain, mais aussi de facteurs relatifs au bloc et à la cinématique. L’article présente une campagne d’essais sur modèle réduit entreprise au LMR (EPFL) afin de mieux comprendre et quantifier l’impact de blocs sur des matériaux granulaires. L’influence de divers paramètres relatifs au sol, au bloc et à la cinématique est mise en évidence.

Jan 1, 2003

By G. A. Brown

Major mining projects are developed with the assistance of lending institutions who provide hundreds of millions of dollars in funding over several years, and of course expect those funds to be returned with interest. Two Australian banks have adopted the Equator Principles, an emerging financial industry benchmark for assessing and managing environmental and social risk in project financing. Project financiers have encountered environmental and social issues that are both complex and challenging, particularly with respect to projects in the emerging markets of Asia-Pacific and elsewhere. There are many recent and historical examples of failures by resource companies to effectively manage their environmental, social, safety and security risks, some of which have caused the project to fail completely, and some of which have caused the temporary cessation of production. These events put the financial institutions&apos; funds at risk through inadequate management capacity and non-compliance adversely affecting the ability of the borrowers to repay the loans. They can also reflect adversely on the reputation of the lending institutions. In assessing these risks, lenders are increasingly looking at the track record of the borrower in its country of origin and in other countries where it operates. Lenders are wary of companies that have one standard for operations in a developed country, where the regulatory environment may tightly control what they do, and another standard for operations in countries where the regulatory regime is perhaps less stringent. Lenders may require environmental and social reviews or audits to be conducted on their behalf by competent third parties prior to a loan being approved, and annually over the life of the relationship. The mining industry&apos;s concept of the unwritten `social licence to operate&apos; is highly relevant in relation to the delivery of community benefits that are sustainable post-mine closure. This paper provides examples of recent practices that support financial viability and sustainable development, as well as examples of some failures that have put lenders at risk.

Jan 1, 2007

By J. -P. Tshibangu, A. Vervoort, A. Lavrov

Abstract: The aim of the research presented is to study the effect of complex loading schemes on the fracturing process during loading and/or unloading. A first set of experiments was done using a poly-axial cell. These experiments in combination with numerical simulations showed a difference in micro-fracturing (shear and tensile cracks), but not in macro-failure between various loading/ unloading schemes. The second set of experiments was based on the three-point bending test and several cycles with or without rotation between cycles were applied. If the specimen was rotated by 90° or 180° about its long axis between the first and second cycle, no Kaiser effect was observed. Résumé: Le but de la recherche présentée est d’étudier l’effet de schémas de charge complexe sur le processus de fracturation durant la phase de charge et de décharge. Une première série d’expériences était réalisée utilisant une cellule polyaxiale. Ces expériences combinées avec des simulations numériques ont montré une différence de micro-fracturation (fissures de cisaillements et de traction) pour les différents schémas de charge et décharge, mais en ce qui concerne la macro-fracturation ce n’est pas le cas. La deuxième série d’expériences était basée sur des essais de flexion trois points avec plusieurs cycles, avec ou sans rotation entre les cycles. Si l’échantillon est tourné de 90° ou 180° selon le grand axe entre le premier et le second cycle, l’effet Kaiser n’est pas observé. Zusammenfassung: Der Zweck der vorliegenden Forschung bestand darin, den Einfluß von komplizierten Beanspruchungsschemen auf den Bruchprozess im Laufe von Belastung und/oder Entlastung von Gesteinen zu untersuchen. Der erste hier beschriebene Satz von Experimenten wurde mit einer dreiaxialen Belastungsmaschine angestellt. Diese Experimenten zusammen mit dazugehörigen numerischen Simulationen zeigten Unterschiede zwischen Be- und Entlastungsbeanspruchungen in Bezug auf mikrobruchmechanische Mechanismen (d.h. Scher- oder Zugrisse) an, aber nicht in Bezug auf den Makrobruchprozess. Der zweite Satz von Experimenten umfasste Gesteinsbeanspruchung in mehreren Zyklen von Drei-Punkt-Biegung, indem die Gesteinsproben zwischen den Zyklen um einen angegebenen Winkel (0°, 90° oder 180°) gedreht wurden. Falls die Probe um 90° oder 180° gedreht wurde, wurde kein Kaiser-Effekt im zweiten Zyklus beobachtet.

Jan 1, 2003