Search Documents

By R. Sun, R. G. Gillies, R. S. Sanders, J. Schaan

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is abetter indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By R. G. Gillies

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is a better indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By R. T. Jones

The 20 Mt reverberatory furnace slag dump at Nkana in Zambia contains a substantial quantity of cobalt. A 40 MW DC arc furnace has been built at Chambishi for the purpose of recovering cobalt from the slag. The technology was jointly developed by Mintek and Anglovaal Mining Ltd (Avmin), and the furnace was designed by Bateman Titaco. Testwork at the 150?250 kW scale was conducted at AVRL, and larger scale piloting was conducted at Mintek (in partnership with Avmin) in a 3 MW DC arc furnace. Approximately 840 tons of Nkana dump slag (ranging from 0.66% Co) was processed at power levels around 1-2 MW. Good overall cobalt extraction was achieved, and approximately 100 tons of cobalt-bearing alloy was produced (containing 5 to 14% Co). This testwork demonstrated that the Nkana dump slag could be processed in a DC arc furnace of suitable design, to produce a cobalt-bearing alloy suitable for further hydrometallurgical processing. Bateman Titaco were contracted to design and build the furnace, and the design team contained representatives from Avmin and Mintek. The project was conceived as a fast-track exercise, and many activities had to be run in parallel. Notable features of the furnace include an ABB power supply, a Concast conductive hearth, the refractory design, and copper cooling in the sidewalls. Power to the furnace was switched on during January 2001.

Jan 1, 2002

By P. P. Kim, M. Tangstad, T. A. Larssen

"The kinetics of MnO and SiO2 reduction in SiMn slags based on Assmang/Comilog ore and HCFeMn (highcarbon ferromanganese) slag were investigated between 1500 and 1650°C under a CO atmosphere. The results showed that charges containing HCFeMn slag had relatively faster reduction rates than those without. The difference in the driving force for MnO reduction was insignificant among the SiMn slags at 1500°C, which implies a low contribution of the driving force for reduction rate. The slag viscosities were also rather similar, around 1 poise at 1500°C, which could not explain the different reduction rates. Instead, the different charges containing various sulphur contents are believed to give rise to the varying reduction rates. The estimated activation energies for MnO reduction were around 500–920 kJ/mol for charges containing HCFeMn slag, and between 250–300 kJ/mol for those without. Based on the estimated kinetic parameters, the considered rate models were able to describe the reduction of MnO and SiO2 in SiMn slags between 1500 and 1650°C. IntroductionManganese ferroalloys such as ferromanganese (FeMn) and silicomanganese (SiMn) are important ingredients in steel production due to the beneficial effects of manganese on the physical properties of steel. Mn enhances the strength, toughness, and hardness of steel products, and both Mn and Si are used as deoxidizers to prevent the development of porous structures (International Manganese Institute, 2014; Olsen, Tangstad, and Lindstad, 2007; Subramanyam, Swansiger, and Avery, 1990; Tomota et al., 1987).The thermodynamic background of manganese ferroalloys is well established (Olsen, Tangstad and Lindstad, 2007), but kinetic information is rather scarce, especially for the SiMn process (Tranell et al., 2007; Tore-Andre Skjervheim, 1994). The absence of kinetic information makes it more difficult to understand the reduction mechanisms of MnO and SiO2. It is not clear how different raw materials affect the SiMn process. The main metal-producing reactions in the SiMn process are described by Equations [1] and [2]:"

May 1, 2019

Mixtures of MnO and graphite were reacted under argon at temperatures ranging from 1200 to 1425°C, and the loss in mass of the mixture was recorded continuously. The results showed that the rate of reduction of MnO increased as the temperature increased and the ratio of MnO to C decreased. The effect of the particle size of MnO and of graphite on the rate of reduction at I350°C was very small in the range 63 to 250 µm for MnO and 45 to 355 µm for graphite. The rate of reduction at I350°C was increased markedly by the addition of Na2CO2 and K2CO3, was slightly increased by the addition of Fe2O3, was unaffected by the addition of CaO, MgO, and AI2O., and was decreased by the addition of SiO2. Some CO2 was always present in the effluent gas, and this was taken as evidence that the reduction of MnO occurred by way of CO2 as an intermediate product. The activation energy of the ratecontrolling step was 57,5 kcal, and this was similar to the measured activation energy for the gasification of graphite by CO., namely, 61,S kcal per mole of graphite. A simple kinetic model was derived on the assumption that the gasification of graphite was the ratecontrolling step, and the results over the temperature range 1200 to I425°C, when plotted in the appropriate form, yielded straight lines as predicted by the model.

Jan 1, 1980

By Elizma Ford, Vincent Sithole

"Two shortened test procedures for estimating the Bond ball work index are compared for suitability of use on Zambian/DRC-type copper–cobalt ores. The first procedure is based on a batch milling test while the second procedure is based on a limited locked-cycle test. Both procedures were conducted using a standard Bond test mill. INTRODUCTION The Bond ball work index is widely used in the field of minerals processing as an indicator of ore grindability. The work index is determined by means of a locked-cycle test procedure that typically requires seven to eight cycles to stabilise at a re-circulating load of 250%. A typical test requires between three to four kilogram of ore sample and around eight hours of operator time. For geometallurgical test work applications, where a large number of variability samples are to be tested, it would be highly beneficial to use a test procedure that requires less sample mass and operator time. Certain test work laboratories, for example SGS and JK Tech, are already offering various types of shortened test procedures for estimating the Bond ball work index. This paper discusses a comparison of two shortened test procedures that were evaluated for suitability of use on Zambian/DRC-type copper–cobalt ores. EXPERIMENTAL Test Procedure 1 – Batch Milling The first test procedure is derived from a batch milling approach proposed by the University of Hacettepe (Aksani, 2000). Some modifications were, however, made to the data analysis method from that originally proposed. During this test procedure, a 700 mL volume of sample is milled in a standard Bond test mill for a pre-determined number of revolutions. The feed and product particle size distributions are measured for each test. These results are then used to back-calculate a cumulative breakage rate parameter (k) for each particle size, according to the following formula:"

Jan 1, 2015

By N. Fardin, O. Stephansson, L. Jing

A pair of silicon rubber replicas of size 250 mm by 250 mm, from a natural rock joint, was used to produce several high strength concrete fracture replicas of different sizes, from 50 mm by 50 mm to 200 mm by 200 mm. The morphology of the concrete fracture replicas were digitized at the laboratory using a 3D-laser-scanning machine with high accuracy and resolution. The scale dependency of the geometrical properties, including surface roughness and aperture, of the samples were investigated using fractal method. The investigation was extended to study the scale effect on the mechanical properties of the concrete fracture replicas. Four concrete replicas having same geometry from each sampling size were sheared under four different normal loads. The results show that normal and shear stiffness and peak shear strength decrease with increasing sample size and decreasing normal stress. It is concluded that for accurate determination of geometrical and mechanical properties of rock joints in the laboratory and field scales, samples with size equal to or larger than stationarity limit are required. Silikongummiabdrücke der Größe 250 mm x 250 mm einer natürlichen Kluft dienten als Vorlage für mehrere Hochfestbeton Rissreplikas verschiedener Größe. Die Morphologie der Beton Rissreplikas wurde mittels eines 3D-Laserscanners hoher Genauigkeit und Auflösung im Labor digitalisiert. Die Skalenabhängigkeit der geometrischen Eigenschaften, dies inklusive Oberflächenrauhigkeit und Öffnungsweite, wurden mittels Fraktalen bestimmt. Die Studie wurde durch die Untersuchung der mechanischen Eigenschaften der Betonrepliken erweitert. Hierbei wurden vier Betonrepliken der selben Geometrie jeder Probengrösse unter vier verschiedenen normalen Belastungen abgeschert. Die Ergebnisse zeigen das sowohl Normal- und Schersteifigkeit als auch die Spitzenscherfestigkeit mit zunehmender Probengrösse und abnehmender Normalspannung abnehmen. Es hat sich gezeigt, daß für eine genaue Bestimmung der geometrischen und mechanischen Eigenschaften von Felsklüften im Labor und im Feld Proben einer Größe gleich oder größer des stationären Limits verlangt werden. Deux répliques en gomme de silicone d’une fracture naturelle, de dimension 250 mm par 250 mm, ont été utilisées pour produire des répliques en béton de haute résistance de dimensions allant de 50 mm par 50 mm à 200 mm par 200 mm. La morphologie de ces répliques a été digitalisée au laboratoire à l’aide d’un laser-scanner 3D haute résolution et haute précision. L’influence de l’échelle des propriétés géométriques, incluant rugosité et ouverture, a été étudiée en utilisant la méthode des fractales. Des essais complémentaires ont été réalisés afin d’étudier l’effet d’échelle sur les propriétés mécaniques des répliques de fracture en béton. Quatre répliques béton de même géométrie pour les différentes tailles d’échantillons ont été cisaillées sous quatre valeurs de contrainte normale. Les résultats montrent que la rigidité normale et tangentielle ainsi que la résistance de pic diminuent en proportion de l’augmentation de la taille de l’échantillon et de la diminution des contraintes normales. On peut en conclure que, pour une détermination précise des propriétés géométriques et mécaniques des fractures au laboratoire et sur le terrain, des échantillons de taille égale ou supérieure à la limite stationnaire sont nécessaires.

Jan 1, 2003

"Chairman: Dr R. E. ROBINSON Rapporteur: Dr R. P. COLBORNPapers:The simulation of crushing plants by W. J. WhitenSimulation of multi-component flotation plants by B. K. Loveday and G. R. MarchantComputer control of flotation at the Ecstall concentrator by M. P. Amsden C. Chapman and M. G. ReadingModel for the design and control of flotation plants by R. P. KingIn presenting his paper Dr W. J. Whiten outlined the basic concepts on which the control model was based and emphasized the fact that empirical models based as much as possible on theory were used to simulate each unit of the crushing plant. The final parameters of each model were computed using data collected from the plant. Unfortunately, the system did not permit accurate extrapolation but was successful when operating in the region from which the parameters were calculated.He concluded from the results of the test work that the crusher amperage was a critical parameter and that the utilization of the model gave a 15 per cent increase in the plant output. This was because the model predicted that a marginally fine grind would provide a significant increase in throughput. Dr Whiten elaborated on what constituted the multiple spline regression, explaining that it was a least-squares curve-fitting technique in one or more dimensions, where the calculation of coefficients in analytic expressions was replaced by the calculation of typical points on a very smooth curve called a spline function. The emphasis was placed on the shape and value of the curve or curves instead of on the coefficients as in analytic regression. A spline function was the line drawn between all points constituting the data set.Dr B. K. Loveday commented that the simulation was unusual in that the optimum throughput was considered to be the maximum throughput, which, surely, was limited by the crusher size. He also emphasized the importance of the interaction between both crushing and grinding circuits and added that in practice the optimum operating conditions were inter-dependent. Dr Whiten replied that in the case of the plant under consideration, the crushing process was not, in fact, the limiting operation.Mr C. E. Clifford indicated that the model was being used to simulate a number of crushing and grinding circuits at Mount Isa Mines. He reported that the model simulated the circuit satisfactorily for primary and secondary gap settings of 0,625 in. to 0,375 in., but that adjustment had to be made to the model parameters for gap settings of 0,250 in. to 0,125 in.In reply to a question from Dr D. M. Hawkins, Dr Whiten said that he preferred to use low-order splines with smaller segments rather than high-order spline functions with large segments."

Jan 1, 2014

By M. Kwasniewski, M. Takahashi

Prismatic samples of a medium-grained sandstone from Slask Colliery (Upper Silesian Coal Basin, Poland) were tested under uniaxial compression, conventional triaxial compression and true triaxial compression conditions. The conventional triaxial compression tests were carried out at confining pressure (p) equal to 12.5, 25.0 and 37.5 MPa. In the true triaxial compression tests the minimum principal stress (s3) was equal to 25.0 MPa and the intermediate principal stress (s2) was 1.5, 2 and 2.5 times higher than s3. Results of the studies show that confining pressure strongly inhibited dilatant behavior of rock samples tested under conventional triaxial compression conditions; the increasing confinement resulted in the growing compaction of the rock material. The effect of dilatancy was also highly suppressed by the intermediate principal stress. While important dilatant, negative volumetric strain corresponded to the peak differential stress at low intermediate principal stress conditions, at high intermediate stresses the rock material was damaged to much lesser extent. As a result, faulting of rock samples in the post-peak region was much more violent and was accompanied by a strong acoustic effect. Les échantillons parallélépipédiques du grès à grains moyens de la mine ‘Slask’ (Bassin Houiller de Haute Silésie, Pologne) ont subi les essais de compression monoaxiale (compression simple), de compression triaxiale conventionnelle (compression triaxale de révolution) et de compression triaxiale vraie. Les essais de la compression triaxiale conventionnelle ont été effectués à la pression de confinement de 12,5, 25,0 et 37,5 MPa. Dans les essais de compression triaxiale vraie la contrainte principale minimale (s3) était de 25,0 MPa et la contrainte principale intermédiaire (s2) était 1,5, 2 et 2,5 fois supérieure de s3. Il résulte des essais que la pression de confinement inhibe fortement le processus de dilatance dans les échantillons testés dans les conditions de compression triaxiale conventionnelle; l’augmentation de la pression provoquait l’augmentation du compactage du matériau rocheux. Le phénomène de dilatance était également limité de façon significative par la contrainte principale intermédiaire. Alors que l’importante déformation volumique négative correspondait à la contrainte différentielle ultime avec les faibles contraintes principales intermédiaires, dans les conditions de fortes contraintes intermédiaires, le matériau rocheux subissait l'endommagement de façon beaucoup moins importante. En résultat, la rupture des échantillons rocheux au stade post-maximum était beaucoup plus violente et accompagnée d’un fort effet acoustique. Prismatische Probekörper des mittelkörnigen Sandsteines aus dem Bergwerk ‘Slask’ (das Oberschlesische Kohlengebiet, Polen) wurden unter der einaxialen Druckbeanspruchung, konventionellen dreiaxialen Druckbeanspruchung und der echten dreiaxialen Druckbeanspruchung geprüft. Konventionelle dreiaxiale Druckversuche wurden bei dem Manteldruck von 12,5 25,0 und 37,5 MPa durchgeführt. Bei den echten dreiaxialen Druckversuchen betrug die kleinste Hauptspannung (s3) 25,0 MPa und mittlere Hauptspannung (s2) war 1,5-, 2- und 2,5-mal höher als s3. Aus den durchgeführten Versuchen ergibt sich, dass der Manteldruck die Dilatanzentwicklung bei den Probekörpern unter der konventionellen dreiaxialen Druckbeanspruchung stark bremst; die Erhöhung des Druckes rief die ansteigende Kompaktion des Gesteinsmaterials hervor. Die Dilatanz wurde auch durch die mittlere Hauptspannung beschränkt. Während die wesentlichen volumetrischen, dilatanten Verformungen der Grenzdifferenzspannung bei den niedrigen mittleren Hauptspannungen entsprachen, bei den hohen mittleren Hauptspannungen wurde das Gesteinsmaterial viel weniger beschädigt. Im Ergebnis war der Scherbruch der Gesteinsproben im Post-Peak-Bereich viel heftiger und mit kräftigen akustischen Effekten verbunden.

Jan 1, 2003

By A Weber, L MacNamara, H Schreiber

Design and development of the world?s largest flotation cell was completed in 2002. This was the first 257 m3 flotation cell installed in the mineral industry and represents a major development in the design of larger flotation cells. This cell has a 50% increase in volume over the widely installed 160 m3 WEMCO® Smartcell? flotation machine. In the next few years it is anticipated that 257 m3 flotation cells will be incorporated into rougher-scavenger flotation circuits in many more world class copper sulphide concentrators. The prototype 257 m3 cell, No.250 Smartcell? flotation machine was installed at Minera Los Pelambres in the front of Row 1 in the existing rougher flotation circuit. This cell is followed by nine No. 130 Smartcell? flotation cells. After the successful development phase, this unit has been incorporated as part of a row of No. 250 Smartcell? flotation machines at Minera Los Pelambres. A key to the successful development of the equipment has been the emphasis placed on fundamental hydrodynamic scale-up criteria. Hydrodynamic factors include superficial gas velocity, water (pulp) circulation through the draft tube, and pulp mixing (distribution) characteristics. This paper will review the scale-up criteria of the No. 250 flotation cell, and present a case study of the in-plant equipment testing. The case study will document the metallurgical and hydrodynamic performance of the machine. It will also illustrate the economic benefits derived by incorporating larger flotation cells in a modern copper sulphide concentrator.

Jan 1, 2007

By R. H. Matjie, J. R. Bunt, A. C. Collins, J. C. van Dyk, C. A. Strydom

South African discard coal fines and K₂CO₃ blends were heated in a laboratory-scale rotary kiln to produce ashes for H₂SO₄ leaching tests. The optimized H₂SO₄ leaching conditions of 6.12 mol.dm³ (M) H₂SO₄, solid to liquid ratios 1:5 and 1:10, and 80°C for 8 hours were used. K₂CO₃ was added to increase the dissolution efficiency of K. The objective was to determine if the Al present in metakaolinite (Al₂O₃.2SiO₂), the Al, K, and Ti in the alumino-silicate glasses, and the Ti in rutile (TiO₂) in the ashes could be selectively dissolved in H₂SO₄. XRF results show that the ashes formed at 700°C dissolved more efficiently (87% Al, 89% K and 23% Ti) compared to the ashes formed at 1050°C. This can be attributed to the presence of Al₂O₃.2SiO₂, K₂CO₃ melt, K₂CO₃ remnants, KAl(SO₄)₂, and K-aluminosilicate glass in these ashes. XRD results indicate that the ashes prepared at 1050°C contained anorthite (CaAl₂Si₂O₈), microcline (KAlSi₃O₈), pseudomullite (Al₂O₃.SiO₂), and silicon spinel (2Al₂O₃.3SiO₂), which are either insoluble or only sparingly soluble in H₂SO₄. These minerals resulted in the lower dissolution efficiencies of Al and K. Based on the high dissolution efficiencies of Al and K for the ashes produced at 700°C, coal fines blended with K₂CO₃ could possibly be utilized as feedstocks for the production of aluminium(III), potassium(I), and titanium(IV) and a sulphate-containing leach liquor. Furthermore, the environmental issues and costs associated with the handling and disposal of large volumes of coal fines will also be resolved.

Aug 2, 2022

By P. Pięta, A. Surowiak, T. Niedoba

In a flotation process of copper ore three factors were measured: copper grade in concentrate (β), copper grade in tailings (J) and recovery of copper in concentrate (e). The experiment was conducted by means of the Jameson cell. The factors influencing the quality of the process were particle size (d), time of separation (t), type of the collector (k) and dosage of the collector (s). The considered vector function was then [β(d, t, k, s), J(d, t, k, s), e(d, t, k, s)]. Optimisation achieved was based on determining the values of the adjustable factors (d, t, k, s). The goal was to obtain the highest possible values of functions β and e (maximum) and the lowest possible values of function J (minimum). To this purpose the taxonomic methods were applied. Keywords: Flotation, copper ore, lithology, flotation agents, particle size distribution, taxonomic methods

Jan 1, 2020

By H. A. Bilgin, A. Özgenog?lu, G. Kaçar

In this study, the influences of rock mass properties on the blasting performance in open cast mines are investigated. To this end, discontinuity spacings and discontinuity orientations are measured and full scale blasts with various designs are observed in open cast mines of Aegean Lignite (ELI) and Bursa Lignite (BLI) Establishments belonging to Turkish Coal Enterprises (TKI). For each blast, blasting cost is calculated, and particle size distribution representing the fragmentation of muckpile is determined by means of Split-Desktop software using image processing. 50%(K50), 80%(K80) passing sizes and topsize values are used in the determination of blasting performance according to rock mass properties. The relationships between orientation angle, which is the acute angle between the strikes of slope face and major discontinuity, and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of major discontinuity orientation on fragmentation and blasting cost. Furthermore, the relationships between discontinuity modal spacing (or block size index) and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of discontinuity spacing on fragmentation and blasting cost. In this paper, the trends observed in these relationships are discussed and the importance of it in mining is commented. Dans ce travail, Il a été traite les influences des qualites des rocheux massif sur les performances des abattages de l’excavation a ciel ouvert. Dans ce cas, les excavations a ciel ouvert dans les Entreprises Lignite d’Aegean et de Bursa qui appartient a La Societe Charbon de la Turquie; Il a été mesuré le trou du discontinuite et l’orientation du discontinuite et aussi, Il a été observé les abattages qui sont pareilles aux critaires exactes. Pour chaque abattages, Il a été fait le control des expences et la distribution du particle au dimension du pile qui a été deja abatté, a été trouve en utilisant le Software du Split-Desktop. Pour determiner les influences des qualites des rocheux massif sur les performances des abattages, Il a été utilisé K50, K80, et le plus grand valeurs des dimensions. Aussi pour determiner l’influence sur l’orientation du discontinuite majeur de la fragmentation et les expences de l’abattage, Il a été observé les relations entre l’angle de l’orientation ( C’est l’acutage entre la direction du banquette front et la direction du discontinuite majeur ) et les plus grand valeurs des dimensions et les expences de l’abattage. Plus, pour determiner des influences du trou du discontinuite sur l’abattage et la fragmentation; Il a été observé la relation entre l’index de la dimension du block et K50, K80 et les plus grand valeurs des dimensions et aussi les expences de l’abattage. Pour conclure; on peut dire que dans cette presentation, apres la discusssion des sujets consideres ces relations, Il a été souligné l’importances de ces relations dans la domain de la Minéralogie. In dieser Studie wurden die Einflüsse von Gesteinsmasse Eigenschaften auf die Sprengleistung in Tagebau Bergwerken untersucht. Zu diesem Zweck wurden Diskontinuität Abstände und Diskontinuität Orientierungen gemessen und Sprengungen im Originalmaßstab mit verschiedenen Anordnungen in Tagebau Bergwerken der Ägäischen Braunkohle (ELI) und Bursa Braunkohle (BLI) Betrieben, die zu der Türkischen Kohlegesellschaft (TKI) zugehörig sind, beobachtet. Für jede Sprengung wurden die Sprengkosten berechnet und die Teilchengrößenverteilung zur Darstellung der Aufteilung von Haufwerk ist durch Mittel von Teilbelegungssoftware, das Bildverarbeitung verwendet, bestimmt worden. 50% (K50), 80% (K80) durchlaufende Größen und Spitzengröße Werte wurden zur Bestimmung von Sprengleistung geordnet nach Gesteinsmasse Eigenschaften benutzt. Die Beziehungen zwischen Orientierungswinkel, welches der scharfe Winkel zwischen den Streichen der Hangfläche und Hauptdiskontinuität ist, und 50% (K50) und 80% (K80) durchlaufende Größen und Spitzengröße Werte sowie Sprengkosten wurden untersucht, um die Einflüsse von Hauptdiskontinuität Orientierung auf Aufteilung und Sprengkosten zu analysieren. Außerdem, wurden die Beziehungen zwischen Diskontinuität modal

Jan 1, 2003

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By T. Markus, K. Hilpert

Discharge vessels of advanced light sources are made of translucent polycrystalline Al2O3(PCA).These tubes contain salt mixtures, which essentially consist of metal halides. The salt mixture is present as a melt at the coldest spot of the vessel under operating conditions and vaporizes partly. The temperatures of the coldest spot range between 1200 K and 1300 K, depending on the lamp performance. The maximum wall temperatures range up to 1500 K and for special purposes up to1700 K. Important constituents of the melt are alkali halides AX (A = Na, Cs, X= Br, I) and rare earth metal halides LnX3(Ln = Dy, Ho, Tm). Severe corrosion attack on the wall material is observed in the PCA discharge vessels. The aim of this work is to elucidate the corrosion mechanism. Annealing experiments under well defined temperatures were carried out in order to understand the complex chemical corrosion processes. Two different annealing vessels were used, one for experiments under isothermal conditions with a temperature of 1473 K and one for experiments with a linear temperature gradient from 1450 K to 1600 K. The vessels were filled with salt mixtures of different compositions and annealed for 1000 h. The corrosion attack was characterised by XRD, analytical electron microscopy, high temperature mass spectrometry, and chemical analysis of the salt melts. The results of our investigations show that the corrosion attack is caused by vapour species and by the salt melt. The most severe corrosion is observed in vessels filled with mixtures of alkali halides and rare earth metal halides. No corrosion of the alumina is practically observed if pure alkali halides or pure rare earth metal halides are present in the annealing vessel. Keywords: thermodynamic, corrosion, lamps, metal halide salt

Jan 1, 2004

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By M. B. C. Brandt

The near-surface wave attenuation factor k (kappa), which describes the attenuation of seismic waves with distance in the upper 1–3 km of the Earth, was determined for the Far West Rand gold mining area using seismic data recorded by station Parys (PRYS) of the South African National Seismograph Network. Twenty micro-events in the magnitude range 0.7 ? ML ? 1.8 for the period 1 July to 15 November 2015 were analysed. For the analysis a 10-second window for the S phase portion of the vertical component seismogram was selected. The result was an average k = 0.048 ± 0.014 s, which is much higher than for a stable continental region where k = 0.006 s. This is because the assumed Brune source model is inappropriate for describing mining-related events that often have moment tensors with a volumetric (implosive) component. The average k was calculated to be 0.098 ± 0.038 s for explosions of a similar magnitude. This higher value derived for mining-related k may be employed as a means of correcting the Brune source spectrum to calculate seismic moment as well as corner frequency for events in the mining areas of South Africa.

Jan 1, 2017

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

By S. Ganguly

Slag samples taken from adjacent to the furnace wall of a submerged arc ferromanganese smelting furnace have been found to contain high concentrations of K2O. To characterize the phase equilibria relevant to these slags experimental studies have been carried out to determine pseudo-ternary sections of the form ?MnO?-CaO-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.65 and 6.0 wt% K2O for temperatures in the range 1523-1673 K. In the pseudo-ternary section investigated the primary phase fields are found to be mullite, 3Al2O3?2SiO2; corundum, Al2O3; spinel, MnO?Al2O3; manganosite solid solution, (Mn,Ca)O; dicalcium silicate,2CaO?SiO2; gehlenite 2CaO?Al2O3?SiO2; anorthite CaO?Al2O3?2SiO2; kalsilite KAlSiO4 and leuciteKAlSi2O6. It was found that the presence of K2O in the slag decreases liquidus temperature in the anorthite and gehlenite primary phase fields. The manganosite primary phase field is expanded in the direction of increased (Al2O3+SiO2) and the liquidus temperatures in the manganosite primary phase field are increased significantly with the presence of K2O in the slag.

Jan 1, 2007

[Council for 1994/95 President J.A. Cruise President Elect D.A.J. Ross-Watt Vice Presidents Senior P.D.K. Robinson Junior Dr N.A. Barcza Immediate Past President Dr H. Scott-Russell Honorary Treasurer D.A.J. Ross-Watt Members of Council J.P.W. Bennie Dr L.A. Cramer Prof. R.J. Dippenaar J.R. Dixon A.A.B. Douglas F.M.G. Egerton Prof. R.H. Eric B.R. Fleetwood Dr M.A. Ford Dr R.V.R. Handfield-Jones P.J. Knottenbelt R.P. Mohring K.C. Owen M.H. Rogers K.A. van Gessel P.M.T. White]

Jan 1, 1995