Search Documents

By R. F. Randolph, R. S. Fowkes, J. J. McClelland, G. H. Schnakenberg

Between 1986 and 1992, there were268 deaths and 54,642 severe injuries to workers in underground U. S. mining operations. Clearly, this level of health and safety risk is not acceptable. While most underground coal mining jobs are dangerous, some are much more dangerous than others. Many jobs in an underground coal mine are clustered around the working face—the place where machinery digs coal from the surrounding rock. The hazards in this area are numerous: When the coal is removed, the ground around it becomes unstable and can cave in on the workers. The mining machines used there are large, heavy, powerful, and move in many different directions in a very confined space, presenting danger to workers. Also, the machines churn up coal dust that causes black lung and other ailments. Figure1 shows a modern radio remote controlled continuous mining machine and its operator. In a typical mine, the jobs with the greatest exposure to hazards involve operation of machinery that cuts tunnel-like passages into the coal (the continuous mining machine) and machines that insert supportive steel bolts into the rock above the work area (roof bolting machines). The workers who endure these hazards are at almost twice the risk of death or disabling injury than co-workers in other safer areas of the mine. Of the statistics quoted above, 106 of the 268 deaths and 21,552 of the 54,642 severe injuries occurred in jobs involving equipment at the working face. The operators of roof bolting and continuous mining machines account for only 21% of the work force but suffered 40% of the deaths and 39% of the lost-time injuries during1986-1992. These death and injury rates are almost twice the rate for workers in other underground mining jobs (see figure 2). The estimated total cost of the 106 fatalities and21,552 lost-time injuries was $327 million from 1986-1992. On average, each fatality cost over $1 million and each lost-time injury costs in excess of $9,000.

Jan 1, 1994

By W. J. Fene, H. B. Humphrey, J. J. Forbes

"INTRODUCTION Loss of life from coal-mine explosions in the United States in 1949 was the lowest in any year since before 1870. Although fatality reports from coal nines before 1910 were incomplete,' the explosion fatalities from single disasters or individual States exceeded the 1949 total in each year as far back as 1870, when the records become fragmentary. Since 1890, the only other year in which fewer than 35 were killed was 1946, with a total of 32. Figure 1 shows the total yearly fatalities from explosions in all coal mines and those in anthracite mines alone since 1870. The fatalities in bituminous coal mines were not completely reported before 1910, but enough reports were issued by major coal-producing States to compile reasonably representative figures back to 1885. Any corrections would be additions to these totals.The reason for the moderate total of 46 explosion fatalities in 1948 and the low total of 8 killed in 1949 is thought to be the serious and careful attention devoted to elimination of coal-mine explosion hazards after the disastrous explosions in 1947. The standards now being observed generally with respect to ventilation, rock-dusting, and inspections for gas are better than those found earlier in even the mines having the best reputations for safety. Exceptions are still numerous, but they are fewer, month by month, because of the pressure of Federal and State inspections and a changing conception of the hazards that should not be permitted underground. The prevailing precautions have not eliminated all ignitions of gas or dust, but they have limited propagation to small explosions and have prevented serious loss of life.The number of ignitions (14) reported for the year was less than the average (24) for the 5 years 1944-48 and only half the average for the fiscal years 1929-44. Another favorable factor is that Bureau of Mines representatives were probably in closer contact with both small and large mines in nearly all coal-mining districts. Inspectors now assigned to individual districts are better able to keep informed on the happenings and the progress of safety in their districts. In 1948, one-fourth of the explosions were in mines that employed fewer than 10 men; this condition was duplicated in 1949."

Jul 1, 1950

By John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coal bed at Jim Walter Resources, Inc.'s No. 4 Mine, Brookwood, Ala., where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (308-m) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x 106 ft3 (1.1 x 106 m3). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft3 (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pet. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By Christopher C. Jobes, N. Kumar Kittusamy, Alan G. Mayton, Dean H. Ambrose

Researchers with the National Institute for Occupational Safety and Health (NIOSH) conducted a systematic study to evaluate seat designs on low- and mid-coal-seam shuttle cars. The purpose was to gather additional data to support earlier findings that NIOSH seats, with unique viscoelastic foam padding, are indeed improved designs for coal mine shuttle cars. This study included a larger sample of shuttle car operators than a prior NIOSH investigation. Eight shuttle car operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers then compared the operators’ perceptions with field-measured levels of vehicle jarring/jolting. Seven seat designs were evaluated on low- and mid-coal-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. These seat designs comprised the one already in use on each vehicle and five NIOSH designs. Experimental data were collected using accelerometers, signal conditioning amplifiers, and filters connected to a data recorder, whereas subjective data were gathered via a visual analog scale (VAS) and a questionnaire. Field trials included shuttle cars operating under full- and no-load conditions. VAS responses indicated that NIOSH-designed seats performed better relative to comfort and isolation from vehicle jarring/jolting than the existing seats used in the shuttle cars. Both mid- and low-coal-seam shuttle car operators, during no-load and full-load conditions, rated lower levels of jarring/jolting with the NIOSH seat design. Questionnaire responses indicated that shuttle car operators rated NIOSH seat designs as more comfortable. Vehicle operators most frequently suggested the addition of armrests as a way to improve the seats on the mid-seam shuttle car. The quantitative levels of vehicle jarring/jolting for the no-load condition (more severe condition for vehicle operation) showed that NIOSH seats for the mid-coal-seam shuttle car performed better than the existing seat in terms of peak acceleration and crest factor. Similarly, for the low-coal-seam shuttle car, NIOSH seats performed better than the existing seat in terms of peak acceleration, root-mean-square (RMS) acceleration, and crest factor.

Jan 11, 2006

By R. D. Leitch, W. P. Yant

"In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information- as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report.The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. .Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and to others for information received; and to Dr. R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.The Lower Kittanning is the most important bed in the locality studied. A great many of the abandoned mines examined are in this bed, and nearly all of the present active ones are. The Upper Freeport bed is also mined to some extent, and a number of the abandoned mines formerly worked this bed. As only three active mines are now (1927) working the Upper Freeport, the comparison of acidities is necessarily limited. Of these three, one had been idle since 1922 until shortly before it was sampled.The location of most of the mines was already known from previous work, but some of them had to be located by following up streams known to contain acid waters. A sample of the- outflow was collected in self-sealing bottles known as ""citrate bottles"" for the determination of dissolved oxygen by the Winkler method.5 Another sample was taken for the determination of acidity according to standard methods of water analysis.6 Ferrous iron was determined at the mine or very soon after taking the sample by titrating with a standard solution of potassium permanganate in acid solution. The hydrogen-ion value was determined by a standard double-wedge comparator.7From the total acidity values in each sample, which are the most important values, the total iron was calculated on the assumption that acidity as sulphuric acid was due to dissolved ferrous sulphate. This assumption is commonly made for mine waters, but is inaccurate to the extent that free acid is already present, and some of the iron is present as ferric, rather than ferrous, sulphate. The amount of ferrous sulphate may be a rough measure of the extent to which oxygen is lacking within the mine. The permanganate titrations just mentioned showed what part of this total iron was in combination as ferrous sulphate, and the difference .was assumed to be that in combination as ferric sulphate, after correcting for the amount of free acid already formed as shown by the titration values."

Oct 1, 1928

Predict the spontaneous combustion potential of a mining operation using an expert system computer program.

Jan 1, 1994

By Clarence A. Wright, JAMES T. NORTON, JAMES G. PARMELEE

The object of this paper is to give to mining companies and to all others who are interested some idea of the possibilities in the treatment, by differential flotation, of lead-zinc ores of the Coeur d'Alene region and other districts. The purpose of these investiga.. tions is not to evolve a differential flotation process that would replace present methods of gravity concentration but rather one that could be applied to the relatively fine material and slime produced in the mills and treated unsuc_pessfully by gravity methods or by flotation. It is expected, of course, that the products to be obtained by differential flotation would be of much better grade than those now produced by flotation in the Coeur d'Alene mills. In view of the fact that it has been difficult to obtain representative samples of flotation feed from the mills, owing to the necessity of shipping the material wet and free from oil or other foreign matter that might be deleterious to the differential separation of the sulphides, the writers have felt justified in running flotation tests with the mill feeds in order to ascertain whether a differential separation of the sulphides could be effected. However, two different lots of flotation feed were tested for differential flotation, and the results of tests of one of these are given in this report. It is hoped that it will be possible later to test out the flotation feed for differential flotation on a large scale in some of the mills. This paper covers part of the investigations carried on by the United States Bureau of Mines in cooperation with the Idaho Bureau of Mines, the University of Idaho, and certain mining companies of the Coeur d'Alene region. Although the results of the tests included in this report are not to be considered final, they indicate possibilities and may suggest others leading to a solution of the problem of separating lead and zinc sulphides by differential flotation in the treatment of certain ores.

Jan 1, 1921

By R. H. Lien

The Bureau of Mines developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. The modified citrate process involves absorption of sulfur dioxide (S02) in a buffered citric acid solution. The S02-loaded solution is regenerated by countercurrent contact with steam in a packed tower. The wet S02 product is then dried and can be liquefied or further processed to make sulfuric acid. Test data from process investigation unit studies are presented. Material balances, flowsheets, and cost estimates are given for recovering S02 from copper smelter reverberatory gas, lead smelter sintering machine tail gas, and power-plant stack gas. Operating cost estimates show the process will add $0.04 per pound of copper, $0.01 per pound of lead, and $0.015 per kwhr to the cost of the respective operations. These costs could be substantially reduced if a source of waste heat was avail-able to provide the process steam requirements.

Jan 1, 1982

By Michael J. Griffin

Science involves the study of the nature and behaviour of natural things and the knowledge we obtain about them. Scientific endeavour leads to the unfolding of new knowledge and adjustments to our understanding and our behavior. To indicate that we ‘know’ something may merely mean we do not feel able to, or that we do not wish to, disagree with others who claim to know; or it may mean we have either heard about it, or studied it, or understand part of it, or accept that it is true, or have seen evidence to be convinced of its veracity. What do we ‘know’ about the health effects of vibration? There are many unknowns in the field of human responses to vibration. Not all would agree on what is known and what is unknown. This paper seeks to summarize what we know that we know, what it is sometimes claimed that we know, and what we know that we do not know about the relation between exposures to vibration and our health. It also speculates on what we do not know that we do not know. Hand-transmitted vibration What we know we know We know that exposures to hand-transmitted vibration result in various disorders of the hand, including abnormal vascular and neurological function. Not all frequencies, or magnitudes, or durations, of hand-transmitted vibration cause the same effects. What we may claim to know To enable exposures to be reported and compared, they are ‘measured’ and ‘evaluated’ using defined (e.g. standardised) procedures. This involves identifying what is to be measured and specifying how it is expressed by one (or a few) numbers. Summarising a vibration exposure in a single value involves assuming the relative importance of components within the vibration (e.g. different magnitudes, frequencies, directions, and durations), so standards define ‘weightings’ for these variables. The importance of the weighted values may also be suggested, allowing ‘assessments’ according to a criterion (e.g. the probability of a specific severity of a specific disease). Standards for the measurement and evaluation of hand-transmitted vibration define a frequency weighting and time dependencies that allow the severity of vibration exposures to be assessed and the probability of finger blanching to be predicted 1. What we do not know We do not know that the frequency weighting in current standards reflects the relative importance of different frequencies and axes of vibration in producing any specific disorder. We do not know whether the energy-based daily time-dependency inherent in A(8) reflects the relative importance of vibration magnitude and daily exposure duration. Consequently, the relation between A(8) and the years of exposure to develop finger blanching, as in an appendix to ISO 5349-1 (2001), is not well-founded. We do not know, or at least there is no consensus on, the full extent of the disorders caused by hand-transmitted vibration (e.g. vascular, neurological, muscular, articular, central), or the pathogenesis of any specific disorder caused by hand-transmitted vibration, or the roles of other factors (e.g. ergonomic factors, environmental factors, or individual factors). We know that acute

Jan 6, 2006

By F. N. Kissell, C. D. Litton

This study ranks the factors impacting survival during a coal mine fire. It bas already been established that reducing time delays is the most important factor in saving lives. Consequently every event during afire is measured in terms d its duration, and the effectiveness d any action taken to improve survival is measured in terms d the time it saves. By ranking actions according to time saved these authors found that a comhination d actions was most effective. This combination was: • installing lifelines. • moderately decreasing air leakage and • decreasing the fire growth rate. Changing ventilation leakage alone was much less effective, as was altering the CO (carbon monoxide), sensor alarm threshold. These results confirm an earlier fault-tree study on escape from mine fires. The fault-tree study bad shown that, with the exception d delays, single factor changes have minimal impact. Significant reductions in fire fatalities only take place with multiple factor changes.

By J. F. McIlwain

The Bureau of Mines investigated fumes generated by selected welding materials used in mines in order to help determine their relative hazard potential. The initial phases of the study have been completed. A welding-fume generation and collection apparatus was designed, assembled, and calibrated. Five brands of coated, AWS-type E308-16 stainless steel electrodes were tested. Total fume generation rates of 0.39 to 0.51 g/min were measured. Quantitative chemical analyses were conducted for all of the principal firms constituents. Two analytical schemes were used to determine levels of the Cr6+ and Cr3+ species contained in the welding fumes; comparable results were obtained. The Cr6+ was found to be the most hazardous constituent, leading to a maximum allowable total fume exposure of 1 mg/m3. Fume generation rates and fume constituent analyses will be derived for other groups of welding electrodes using similar procedures.

Jan 1, 1983

By R. V. Ramani, P. M. T. White, D. Sutton

5.1 Incorporation with the Master Design Simulator Figure 1 diagrammatically illustrates the interaction between the various sub-systems that go to make up the total Master Design Simulator. As a total system, all sub-systems will be scheduled as needed by the controlling program. The data require¬ments for each will be made available either by providing common storage in core or by outputting data to external storage devices such as magnetic tape, disk, drum, etc. The incorporation of the Geology and Reserves sub-system into the total system involves the establishment of an interface through which data may be readily dissemminated in either direction. This interface will be provided by a geological data library in which all information available from the sub-system is stored and can be readily accessed by the main program and/or other sub-systems. In Figure 7, the information flow between the Geology and Reserves sub¬system and other sub-systems is shown. 5.2 Independent Function Geology and Reserves sub-system is capable of functioning as an independent unit or in direct communication with another sub¬system. This is possible by either continued use of the data library or by redirecting output to other peripheral devices separate from the total system libraries. (Figure 8).

Jan 1, 1974

By Geo S. Rice

"Three men lost their lives in the Black Diamond Coal Mine near Seattle, Wash., recently while wearing oxygen breathing apparatus. The press dispatches stated that these men lost their lives while practicing with the apparatus. Later reports stated that the men died while attempting to make a trip 1200 feet down a 25 degree slope which was filled with black damp, in order to measure the amount of water that had accumulated at the bottom of the mine, and the trip was attempted with oxygen in the tanks of the apparatus with dials indicating only 45 minutes supply. The oxygen in the tank was used up and the men therefore lost their lives from a deficiency of air to breathe.In spite of all the education and training done by the Government to prevent accidents, men are prone occasionally to take unnecessary chances. Every piece of apparatus, no matter how perfect, has its limitations. The Government, through the agency of the Bureau of Mines, has trained many thousands of miners in the use of mine rescue apparatus. The training has been given to all miners who requested it, and the Bureau has gone to the extreme of urging miners to join the rescue and first-aid classes. In spite of all the efforts of the Government, men occasionally attempt the impossible."

Jul 1, 1920

This report covers the work performed by the Advanced Products Division of FMC Corporation under Bureau of Hines Contract J0155166, Design Evaluation for Development of an Advanced Bolter Module. FMC has evaluated the existing ISMS bolter designs, and the corrections and improvements in progress, including the effect of the three-chain magazine presently being fabricated, and recommends that a complete bolter module featuring a new magazine, safety post and lower stabilizer or similar device be designed, fabricated, and tested, A 29 week program is proposed which includes a four week demonstration. This module would eliminate those reliability problems not presently being solved and would provide a reliable bolter module for a production oriented miner/ bolter.

Jan 1, 1975

By Alexander E. Morrow

Oxygen breathing apparatus for use in mines was introduced to the United States in 1907. Despite their intended purpose of safeguarding lives, the apparatus led to the deaths of many men because of inherent or developed defects in the equipment, lack of training,, physical shortcomings of wearers, and improper procedures. The Bureau of Mines pioneered in research and training to curb logs of life among users of such apparatus and promoted development of safer equipment and procedures. As a consequence, deaths have been far less frequent. In 1944 the Bureau issued Information Circular 7279, Loss of Life Among Wearers of Oxygen Breathing Apparatus. That publication listed the case histories of 26 deaths that had occurred since the introduction of such equipment to American mining. The author, the late G. W. Grove,3/ asserted that further loss of life could be avoided if good equipment were used, teams were properly trained, and the basic principles of safe procedure were followed. This publication is a sequel to I.C. 7279 and contains information on eight deaths among wearers of oxygen breathing apparatus that were overlooked in the original compilation. It also describes the single death that occurred since I.C. 7279 was published.

Jan 1, 1959

By D. W. Bridges, Donald R. Peterson, Masami Hayashi

Techniques are described for recovering about 80 pct of the cobalt and nickel contained in superalloy scrap by anodic dissolution of the scrap and simultaneous electrodeposition of a pure cobalt - nickel alloy at the cathodes in an electrolytic cell partitioned by permeable diaphragms into separate anode and cathode compartments . Superalloy scrap was alternatively prepared for subsequent anodic dissolution either by melting and casting massive scrap into suitably sized anodes , by packing moderate - sized discard scrap in inert metal baskets that subsequently served as anodes , or after concentrating the superalloy portion of grinding debris , by magnetic separation to reject corundum or other abrasives , slagging any remaining abrasives from molten grindings , and finally casting the superalloy metal into anodes . In the processing , purified electrolyte -- 1 N in NiSO4 and in NiCl₂ , and 0.1 N in CoSO4 and in CoCl2 --was charged to the cathode compartments and discharged from the anode compartments at a rate sufficient to overcome the backward migration of ionic impurities from the anodes to the cathodes . Discharged electrolyte was purified by reacting it first with SO2 and next with limestone , and then recirculated to the cathode compartments , in which a 50 pct cobalt - 50 pct nickel alloy was deposited on either blanks of stainless steel or starting sheets of cobalt - nickel alloy . The process was made self - sustaining by either adding H2SO4 to the catholyte feed to throttle the rate of cobalt - nickel deposition , thereby compensating for the slower rate of cobalt - nickel dissolution from the anode and losses occurring in electrolyte purification , or alternatively , adding H₂SO4 to

Jan 1, 1964

By Harold J. Rose

The economic situation in Switzerland during recent years has resulted in theoretical studies , engineering development work , and many commercial installations of ingenious methods for using energy more efficiently . The purpose of the present investigation was to learn of recent Swiss developments for the more effective use of coal , which comprises 98.9 percent of the romaining known mineral - fuel reserves of the United States .

Jun 1, 1947

By N. Kumar Kittusamy, Richard E. Miller

This field study evaluated a newer and older dozer at a construction site. Both dozers performed similar activities in the same location within the construction site. Two operators participated in this study. One operator used the older equipment and the other operator used the newer equipment. Jolting and jarring measurements were taken at the seat/operator interface and at the floor of the cab. The result of this field study indicates that the newer dozer was better than the older dozer.

By G. Nuñez, M. A. Pathak, C. F. Stanley

"Holographic interferometry is a non-destructive technique to detect small deformations1 of an object. It is a whole-field technique· with an accuracy of a few microns. An adaptation of holographic interferometry is time-averaged holographic interferometry which is particularly useful in detecting small vibration amplitudes of an object under investigation. Its application to biological tissue is especially difficult due to the combination of (a) the high sensitivity of the technique, and (b) the tendency of these objects to deform excessively, or move during the testing period. (This is also compounded by the changing moisture content of the tissue surface.)Ideally, a pulsed laser and fast-acting thermoplastic film camera could be chosen to overcome these difficulties, but the total equipment cost could exceed $75,000. In this paper we describe our relatively economical method to apply time· averaged holographic interferometry to an excised animal lung, utilizing holographic plates and a mechanically-shuttered continuous-wave Argon laser.EXPERIMENTAL METHODThe schematic of the experimental setup is shown in Fig. 1. The holographic equipment, including the laser, is fixed on a 3 ft x 6 ft x 4 in. honeycomb holographic table. This table is functionally similar to one described by Mark and Horsch2 which can be constructed for about one thousand dollars. The holographic table itself rests on six inner tubes to absorb floor vibrations. All unnecessary vibrations must be reduced to preserve the quality of the holograms. A laser beam from a 0.5-watt continuous-wave Argon laser is split by a circular variable beamsplitter (Newport Corporation Model 50GOOAV.1) into two beams, i.e., an object beam and a reference beam. The object beam is again split into two beams of equal intensity by a 50150 beamsplitter (Newport ·Corporation Model BS.1). These beams are optically filtered and expanded by spatial filters (Newport Corporation Model 910) to cover as much area of the object as possible. Soft biological tissues exhibit low reflectives, resulting in a relatively high reference to object beam ratio of roughly 5 : 1 at the holographic plate."

Jan 1, 1989

By Spencer P. Howell, J. F. Xrawshaw

"A recent premature explosion in a quarry that resulted in the death of nine men and the injury of several others, was directly traceable to a spark from a steam-shovel working under the face directly in front of the hole being loaded. This accident and similar accidents on record in the Bureau of Mines indicates the necessity for pointing out the dangers in quarries of explosives being ignited by sparks emitted from steam shovels and locomotives, and making recommendations for greater safety.Many premature explosions of which the following are examples, have resulted from sparks, both from steam shovels and passing locomotives. (A) The premature explosion occurred during August, 1920 at a limestone quarry, in a 100-foot drill hole, loaded with 1000 pounds of high-grade nitroglycerin and gelatin dynamites. This hole had been loaded with 500 pounds of 75 per cent strength gelatin dynamite, 300 pounds of 60 per cent straight nitroglycerin dynamite, and 200 pounds of 50 per cent straight nitro¬glycerin dynamite; but no steaming had been placed in the hole. The powderman loading the hole saw the spark enter the hole and was able to run a short distance before the explosion took place, thus escaping serious injury. The explosion of this first hole was transmitted to nearby hole similarly charged. The fall of rocks from these two holes buried the steam shovel and some of the gang of men working around it.(B) In September, 1909, in the Canal Zone, a steam shovel uncovered a misfired charge of dynamite. While the dynamite was being picked up the steam shovel continued working nearby. A spark from the shovel set fire to some loose dynamite spilled on the ground from the troken cartridges. This fire was transmitted to a hole which was being loaded close by and caused a premature explosion. One man was injured."

Nov 1, 1920