Search Documents

By D. E. Anders

Saturated hydrocarbons from 60 selected samples of a 2,300-foot Green River Formation oil-shale core (Piceance Creek Basin, Colo.) were analyzed by gas-liquid chromatography techniques. Emphasis was placed upon the distribution of normal alkanes and 15 key-branched and cyclic alkanes. The latter compounds consisted of the C15, C16, C18, C19, and C20 chain isoprenoids, the 5-a and 5-ß C27, C28, and C29 steranes, three C30 pentacyclic triterpanes, and perhydro-ß-carotene. The results showed definite evidence of maturation of both the n-alkanes and the branched and cyclic alkanes; however, most if not all of the changes were limited to the indigenous soluble extract and were not the result of additional soluble extract generation from the insoluble kerogen. Source material and environmental variations were important factors in some of the observed differences in the branched plus cyclic alkane compositions.

Jan 1, 1973

By G. T. Brow

An experimental method is described for testing diffusion of gases in crude oils at pressures and temperatures up to 3,000 psia and 200° F. A sampling technique was developed to withdraw by constant-pressure mercury displacement about 60 µl of oil from the diffusion cell through any of several 1/2-in vertically spaced capillary tubes and to trap about 4 µl of the oil in a specially designed microsampler. Oil trapped in the microsampler can be completely inserted in the sample inlet of a chromatograph. From analysis in a three-stage chromatograph (GLC), gas concentration in a sample is determined from the ratio of gas peak heights to area of peaks of reference components (hexanes or heptanes) in the oil. A diffusion coefficient is calculated from measured concentration profiles with known equations for diffusion in finite or semi-infinite systems, depending on whether the gas has or has not reached the end of the oil column. Results are given for a test of methane diffusing at 2,560 psia and 160° F in crude oil from the Weber Sandstone reservoir in the Rangely field, Colorado. A constant diffusion coefficient of 3.34 X 10-5 cm2 per sec was obtained which gives a good fit between calculated and experimental profiles determined at six times after start of diffusion. The maximum standard error of gas concentration determinations experienced with this method was ±0.88 ml per ml of gas-free oil.

Jan 1, 1970

By d&apos, Kathleen J. Amico

This summary appears in Minerals Yearbook volumes I-II, and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonweath of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The sections of this chapter and the area chapters in volume III contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1967

By M. L. Whisman

The Bureau of Mines developed a radiotracer method for detecting the contribution of selected components and additives to thermally induce deposits of turbine aircraft fuels. Fuels were examined before and after 52 weeks of storage at 130° F. Of particular concern was the influence of aromatic hydrocarbon fuel constituents on thermal-stability quality of jet fuels during storage. A microfuel coker test apparatus was used to thermally stress the test fuels and blends, and the resultant contribution to deposits of selected fuel components, labeled with carbon-14, was determined by radioactive-counting techniques. Ninety-one blends of five test fuels with carbon-14-labeled fuel additives or components were prepared, tested, stored for 52 weeks at 130° F, and reanalyzed for deposit-forming tendency. These additives included two anti-oxidants, a metal deactivator, and a corrosion inhibitor. Of the labeled hydrocarbon fuel systems studied, the greatest reaction was observed in blends containing methyl-and ethyl-substituted indenes. Other aromatic types also showed some contribution to the deposits. Three of the additives showed a marked tendency to degrade and react during storage and thermal stress. A cresol antioxidant, however, barely contributed to deposit formation. Oleic acid interacted with cadmium present in aircraft fuel systems and produced deleterious effects upon the thermal-stability quality of the fuel.

Jan 1, 1971

By F. D. Wang

The Bureau of Mines has developed a computer program for evaluating pit slope stability by the finite element stress analysis and limiting equilibrium method. The program includes the finite element method of stress analysis using triangular elements, finite-element model mesh generation, plotting of the model mesh and stress contours, calculation of a factor of safety along a circular or a plane failure surface, and location of a critical circular failure surface. Instructions for preparation of input data, an example problem, and the program listing are presented.

Jan 1, 1972

By Christopher Mark

Roof bolt system design means the selection of the type, length, capacity, and pattern of bolts for a particular application. Despite research efforts dating back 50 years, no design methodology has found wide acceptance. This paper begins by identifying four mechanisms that roof bolts use to reinforce the ground. It argues that the reinforcement mechanism is determined by the roof geology and stress level, not by the type of bolt. Next, the attributes of roof bolts are discussed in the light of recent research, including anchorage mechanism, installed tension, length, capacity, timing of installation, and installation quality. Several significant areas of controversy are identified. Design methods from around the world are discussed, including those based on empirical research, numerical modeling, and roof monitoring. Finally, some simple guidelines for preliminary design of roof bolt systems are proposed based on statistical analysis of roof support performance at 37 U.S. mines.

Jan 10, 2000

By Alan A. Campoli

OD March 20, 1989, a meeting was held at the U.S. Bureau of Mines Pittsburgh Research Center at the request of Senator Pete V. Domenici of New Mexico. The purpose of the meeting was to engender a technical relationship between the National Laboratories and the minerals industry. During the meeting, the Director of the Bureau of Mines, T S Ary, suggested that since the Bureau is the focal point for mining research in the United States, it would be appropriate for the agency to act as the liaison between the National Laboratories and the minerals industry. As the first step in this process, the author was selected to perform a 6-month investigation to better define the proper role of the Bureau in this area. As part of the investigation, the mining and mineral-related technology available at 21 major U.S. Department of Energy (DOE) Research Laboratories was reviewed. It was assumed that the broad range of scientific and technical areas covered DOE research would provide fertile ground for mining-related technologies. It was hoped that the applicability of DOE research to this liaison effort would be indicative of Federal laboratories in general.

Jan 1, 2011

By V. Castranova, T-M. Ong, V. Vallyathan, M. J. Keane, W. E. Wallace Jr.

"Inhalation of certain forms of silica, asbestos and some other respirable dusts can result in pulmonary fibrosis, characterized by destruction of the surfaces of alveoli and respiratory bronchioles. Fibrous thickening of the alveolar septa decreases the lung's capacity for gas exchange.Pulmonary macrophage damage by respired dust may initiate the fibrotic response.In one proposed mechanism, dust particles interact with the plasma membrane of a macrophage. This damages the cell or induces some hyperactivity of the cell, resulting in excessive release of lysosomal enzymes and reactive forms of oxygen (1). These reactive enzymes or radicals then damage the alveolar surface epithelial cells. A second mechanism has also been pro¬posed (2,3) in which dust damage to the macrophage causes the release of mediator substances which induce pulmonary fibroblast cell proliferation and increased collagen synthesis. This produces fibrous tissue in the terminal air spaces (4,5).Mineral surface interactions with plasma membrane lipoproteins have been proposed as a mechanism of lytic damage of pulmonary cells by silica dust in numerous models (6,7). The significance of dust surface proper¬ties has been further revealed in studies showing significant changes in dust induced cytotoxicity as a function of dust surface crystallinity and organic or inorganic contamination or coating of mineral surfaces (8,9). Such modification of the mineral surface might interfere with surface sites responsible for the toxicity of dusts for pulmonary macrophages, thus interrupting the early stages of the process of fibrosis.In vitro cellular assay systems using erythrocyte hemolysis or the release of macrophage cytosolic or lysosomal enzymes following dust challenge, have been used to analyze the initial mechanism of dust damage to cells. However the ability of these assays to predict the pulmonary disease producing potential of various dusts is imperfect owing to some ""false positive"" results. These assays as performed are therefore questionable models for the initial lesion in pneumoconiosis or silicosis. In particular, kaolin frequently is found to have comparable biological activity to silica quartz in these assays (10,11).Silica and kaolin have distinctly different fibrogenic potentials. Silica is highly fibrogenic, resulting in both acute and chronic silicosis (12). Some epidemiological data and animal experimentation data have indicated that long term exposure to kaolin can result in pneumoconiosis; however, kaolin is relatively benign as compared to silica (13-18). Kaolin is also of interest because it is one of the major mineral inclusions in Eastern U.S. bituminous coals. We have observed that exposing respirable sized native silica or kaolin for two hours to pulmonary macrophages results in a greater enzyme release for kaolin exposures, on a dust mass basis. Exposure of erythrocytes to the dusts also results in greater levels of hemolysis by kaolin for equal mass respirable dust doses. Therefore, these results do not correlate positively with known disease inducing potentials of the two dusts.Characterization of physical and chemical surface properties of dusts involved in occupational exposures, and characterization of the alteration of those surface properties which are likely to occur upon deposition of the dust in the lung, should improve the identification of respiratory disease hazards.Inhaled dust particles deposited in the lower respiratory tract will come in contact with pulmonary surfactant. This surfactant forms a surface film on and emulsion in the liquid hypophase coating of the alveoli and respiratory bronchioles. The primary constituent of this pulmonary surfactant is the lipid diacyl glycerophosphorylcholine, lecithin (19). Because this lipid is also a major component of cell membranes, it is possible that surfactant can interact with mineral dust to alter its Interaction with macrophages and other pulmonary cells and, thus, it"

Jan 1, 1988

By Gilbert M. Farrior

The electrical resistivity the coefficient of electrical resistivity the Hall coefficient, and the absolute thermoelectric power were determined in this Bureau of Mines investigation for nine compositions of the TiB2-CrB2 sub-system. The numerical values of the electrical resistivity and the thermo-electric power were greater for the intermediate compositions than for the end members. The absolute values of the Hall coefficients and the coefficients of electrical resistivity were less for the intermediate compositions than for the end members. The electrical resistivities and Hall coefficients were about the order of magnitude of most metals--from 34 to 202 microhm-cm and from about 0 to -23.3 X 10-4 cuP/coulomb. The thermoelectric power was somewhat greater than that of most metals--up to 15.6 microvolts per 0 C.

Jan 1, 1965

By F. R. Cattoir

The Federal Bureau of Mines refined chromium from an aqueous electrolytic process in molten sodium chloride-chromium chloride electrolytes. Oxygen and nitrogen contents were reduced by a factor of 10 to 40, but most other impurities were little changed. The product usually contained a little more iron than the feed. Since iron was entering the bath from the iron pot and the graphite liner at a nearly constant rate, contamination of the chromium deposits by it was more serious at low currents and deposition rates. A few runs in an iron cell with a nickel liner yielded chromium containing one half as much iron as the feed, but up to 1.5 pct. nickel. In all cases the anode feed lay in the bottom of the container, which itself was used as the anode connection. With a 12-in. cell, variations in applied voltage from 0.05 to 1.5, in current from less than 10 to over 100 a., and in initial cathode current densities from less than 100 to over 2,000 a./sq.ft. had little or no effect upon the analysis of the metal produced) except for iron content. Changes in bath analysis from 3 to 11 pct. chromium were also without effect. These changes did bring about large differences in the physical forms of the crystals obtained. The thick heavy crystals produced at low voltage and current contained voids which made them difficult to leach free of chlorides. Easiest to leach were the thin leaf-like crystals obtained at around 1 v.

Jan 1, 1960

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

By Stephen Gerard Sawyer

The Bureau of Mines developed a method for analyzing elastically certain types of protective cabs and canopies used on underground electric face equipment. The method is based on plane frame theory, and to be amenable to analysis by this method, cabs and canopies must contain symmetry about one plane. Additionally, protective structures with one or more top members in the long direction that do not frame into the columns should be approximately twice as long as they are wide and have two or more internal top members in the short direction. The assumptions and limitations of the plane frame method as regards analysis of three-dimensional cabs and canopies are discussed. A step-by-step procedure for application of the plane frame method is given, and three example canopies are analyzed following this procedure. Elastic strengths calculated for the three example canopies compare within 10 percent of those computed by the more complicated space frame analysis. Formulas employed in plane frame analysis of cabs and canopies are given in the appendixes.

Jan 1, 1973

By D. E. Shanks

The Bureau of Mines investigated the effects of HCI concentration and solution temperature on the solubility and crystal form of the chlorides of Co, Mn, and Ni when sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increasing HCI concentration in solution caused the chlo-rides of Co, Mn, and Ni to crystallize (salt out) because of the common ion effect. The salting-out crystallization was most effective for NiCI2, which had a solubility of 0.7 pct at 20° C and maximum HCI concentration. COCl2 salted out to a minimum solubility of 9.4 pct at 20° C and 22 pct HCI concentration and increased in solubility at greater HCI concentrations because of the formation of chloride complexes. MnCl2 was intermediate in behavior. The effect of temperature on solubility was greatest for CoCl2 and least for NiCI2, 15 and 7 pct change, respectively, over the temperature range of 20° to 60° C. The salted-out chlorides of cobalt and nickel formed the hexahydrates and those of manganese formed the tetrahydrate in saturated metal chlo-ride solutions at 20° C and low concentrations of HCI. Increasing the temperature or the HCI concentration caused a 108s in waters of hydra-tion. At 60° C, the salted-out crystals of NiCl2 formed the tetrahydrate in HCI concentrations up to 18 pct and the dihydrate at higher concentrations, while cobalt and manganese chlorides formed the dihydrates, even in water.

Jan 1, 1985

By F. Garcia, J. Cervik

The cross-measure borehole technique has been shown by the Bureau of Mines to be an effective method of controlling methane liberated by fracturing the roof strata in longwall gobs where overburden is less than 750 ft (229 m). Boreholes are drilled into roof strata before mining operations affect the roof strata. Longwall mining fractures the roof strata and releases methane from source beds. Surface exhausters or vacuum pumps are used to draw the gas to the surface through an underground pipeline and vertical exhaust hole. The captured methane is thus prevented from entering the mine's ventilation system. About 71 pct of the methane produced by longwall mining in the Lower Kittanning Coalbed was captured by the cross-measure boreholes. Borehole spacing is an important factor affecting the performance of the technique. Interference tests and measurements of methane flows in return air indicate borehole spacing in the Lower Kittanning Coalbed should be limited to about 200 ft (61 m) except on the first 600 ft (183 m) of the longwall, where spacing should be reduced to about 100 ft (30 m) to capture the large quantities of methane released when the first large roof fall occurs. Comparisons between measured and calculated gas pressure differentials on boreholes indicate borehole length can be reduced from 280 to 140 ft (85 to 43 m), which reduces drilling costs significantly. Additional experimentation is necessary to verify the calculations.

Jan 1, 1985

By T. E. Ackman

The Bureau of Mines conducted a study of current trends in methods employed by the coal industry to dispose of acid mine drainage (AMD) treatment sludge. Thirty-three AMD treatment plants, operated by 11 Pennsylvania coal companies, were randomly surveyed. These plants provided data for calculating sludge volumes, as well as information on sludge settling, transportation, and disposal. Onsite visits allowed observation of problems associated with the various methods of sludge disposal: (1) disposal into a deep mine, (2) permanent retention in ponds, (3) disposal at an active coal refuse area, and (4) onsite burial. Method 1 is the most frequently used and the most environmentally sound. It is apparent, based on this representative sampling of AMD treatment plants, that the magnitude of sludge production is such that an aggressive and directed effort in reduction of sludge volume is seriously needed. The areas of major concern are (1) the amount of surface land required for sludge storage and disposal, (2) reclamation of these disturbed surface areas, and (3) effective and efficient means of removing, transporting, and disposing of AMD sludge. In this report, an engineering approach to the practical problems associated with the existing disposal methods is presented, together with recommendations for future research.

Jan 1, 1982

By Franklin D. Cooper

This chapter includes tables for 1979 that were not available in time for publication in the 1978-79 Minerals Yearbook, but it does not include corresponding tables for 1980. The value of raw nonfuel mineral output in 1980 was estimated at $24.8 billion, 8.5% above the 1979 value. Of the 21 metal commodities produced, quantitative output increased for 11 and decreased for 10. The values for 10 metals were up, 10 were down, and 1 was unchanged. Among the 47 non-metallic commodities produced, 14 showed quantitative increases, 32 declined, and 1 was unchanged. In terms of value, 32 nonmetallics increased, and 15 declined.

Jan 1, 1981

By Donald A. Wilson

As part of a continuing effort to maximize metal recovery from domestic secondary resources, the Bureau of Mines investigated a process for recovering the metallic portion of scrap alkaline batteries. A pyrometallurgical method for recovering nickel and cadmium from Ni-Cd scrap batteries previously developed on a laboratory scale, was scaled up to 25-and 43-pound charges. The method employed reduction and/or decomposition in a retort using a minimum of 2.5 percent carbon as a reductant. Metallic cadmium was distilled at atmospheric pressure and a minimum of 900° C. Purity of the recovered cadmium was 99.8 percent minimum and the nickel-iron residue contained less than 0.02 percent cadmium.

Jan 1, 1981

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the char-coals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By Charles L. Kimbell

Following the pattern established in the 1989 edition of this study, the concept of data availability must be addressed, because there are perceptible changes from year to year, and the availability of accurately reported, precisely defined statistics and nonstatistical information provides the only sound basis for analytical studies of any type. As the countries of eastern Europe, including the numerous states that formerly comprised the U.S.S.R., undergo the transition from centrally planned economies' to market economies, there has been a perceptible increase in information availability for rather obvious reasons. Any industrial operation seeing economic assistance from government and/or private sources outside the country in which the facility is sited must provide some appraisal of its operations at the time it seeks assistance, as well as some information on previous performance to serve as tools in evaluating its potential under the proposed development scheme for which it seeks financial assistance. This situation, coupled with governmental recognition that concealment of much of the national mineral production, trade, and consumption data for purposes of national security probably never was really necessary and certainly proved unnecessary with the end of the so-called cold war, has led to the publication of increasing amounts of both statistical and nonstatistical information in the countries undergoing economic transition.

Jan 1, 1993

By Edward D. Thimons

The Bureau of Mines conducted in-mine tests to determine correction factors applicable to low-velocity airflows (below 150 fpm) measured by the smoke cloud, vane anemometer, and oil of wintergreen tracer gas techniques 0 The average correction factors found for these methods of measurement were lower than those reported in the literature for use with higher velocity measurements. All tests measured airflows with controlled average velocities ranging from 50 to 100 fpm. Correction factors averaged about 0.75 for readings taken by the centerline smoke cloud method, remotely controlled and stickheld center" line anemometer, and split traverse stick-held anemometer. For hand-held centerline anemometer and oil of wintergreen tracer gas readings, correction factors averaged about 0.67. Since special anemometers are needed to measure airflows in this low-velocity range, and since proper calibration of these anemometers is difficult and expensive, the use of anemometers for low-velocity measurement is imprac-tical. On the other hand, smoke and oil of wintergreen give results as con-sistent as those obtained with specially calibrated, low-velocity anemometers. Furthermore, they are easy to use and inexpensive.

Jan 1, 1979