Search Documents

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By J. E. Zeilinger

This Bureau of Mines study was conducted to determine the sulfur reduction potential attainable when washing fine-size coal on a spiral concentrator. Crushed samples of Middle Kittanning and Bakerstown bed coals washed on the spiral provided pyritic sulfur reductions of up to 90 percent for the plus 200-mesh material. Pyritic sulfur reductions on the minus 200-mesh material seldom exceeded 30 percent; consequently, this material would require further treatment. The capacity of the spiral was 2 tph per unit when washing l4-mesh by 0 coal. The ability to remove pyrite combined with the higher-than-expected capacity makes the spiral worthy of consideration as a rougher-cleaner in new fine-coal desulfurization circuits.

Jan 1, 1976

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in deter-mining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By D. H. Chambers

Digestion studies were undertaken to develop a method for the rapid dissolution of high-temperature ferroalloy scrap. Laboratory tests showed: (1) dissolution of alloy scrap with ferric ion as the leaching agent was a moderately rapid method of digestion; (2) the dissolution process can be considered as a typical reaction of a metal with chlorine gas, although evidence was obtained to show dissolution as a two-step process, one step as the reduction of ferric ion by the soluble alloy constituents and the other as the oxidation of ferrous ion with chlorine gas; and (3) the attack of ferric ion on the alloy was a function of alloy composition, ferric to ferrous ion ratio, and area of contact between leach solution and alloy. The exceedingly complex nature of alloy compositions and dissolution products generally precluded satisfactory analytical determinations. Results of moderate accuracy were obtained using complex modifications of standard analytical and spectrographic techniques.

Jan 1, 1968

By Paul T. Allsman

THIS CHAPTER reviews the highlights of developments in mining technology during 1956 and presents a special report on the design of mine openings in stable ground. This special report is presented each year in an endeavor to stimulate use of the scientific approach to the solution of problems related to mining technology. Assuming that the literature on mining technology reflects trends in mining, it appears that two areas of activity were given most attention in 1956. One was research on mining technology,4 and the other was improvement of transportation, particularly trackless transportation, both at surface and underground mines.

Jan 1, 1958

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

By M. J. Kovalik

The effects of the process variables on the production of chemical coke on a chain grate stoker, a type of traveling grate, were studied. Six bituminous coals, ranging in volatile matter from 16.7 to 43.8 percent, were successfully carbonized, yielding chemical coke with acceptable physical properties. The coke yields were dependent on the volatile-matter content of the coal. The air fuel ratio had the most marked effect on the yield and characteristics of the resultant coke, and the general furnace performance. Results can only be predicted; the actual yield and quality of coke obtained from any given coal can only be determined by actual tests using the optimum processing variables to obtain a coke with minimum volatile-matter content and to retain as much of the fixed carbon in the original coal as possible.

Jan 1, 1967

By Ned Baker

This report describes the development, construction and testing of a hydrogen-fueled underground mining vehicle. A hydrogen burning engine and a hydride fuel system, both previously developed, were installed on a modified utility vehicle, together with the necessary controls. In tests and in actual use, the vehicle performance in terms of speed, acceleration, and gradeability exceeded that of the standard, unmodified vehicle.

Jan 1, 1985

By Warren D. Longwill

[ ]

Jan 1, 1981

By Richard P. Walters

This Bureau of Mines report reviews and assesses the technology for preparing electrodeposited coatings of the platinum-group metals from molten alkali metal cyanide baths. Methods are described for the preparation and purification of the cyanide electrolyte. Vacuum drying, fusion, and purity of the cyanide salts are discussed. Use of a sodium borosilicate test tube as a sodium-ion-conducting membrane for the addition of the desired platinum-group metal is described. The optimum plating parameters of potential and current density for Pt, Pd, Rh, Ru, and Ir coatings that result in the best deposits are given. A method for producing platinum-rhodium alloy coatings of predetermined composition is also described. The importance of careful substrate surface preparation is illustrated. While problems still remain with respect to coating porosity, careful application of the methods described permits the preparation of adherent, coherent electrodeposited coatings of the platinum-group metals.

Jan 1, 1984

By G. L. Oldright

[Processes by which silver alone is extracted from ores that also cant contain base metals are usually associated in the mind of the period when mines were changing from the production of noble metals to the production of base metals containing noble metals as a by-product. In this transition period the mixed arcs of the partly oxidized ore zone had to be treated instead of the free-milling ore that had been treated in the past or the deeper-lying sulphide ores that were to be smelted subsequently under improved economic and technical conditions.]

Jan 1, 1929

By Mark Flower

A 20L ignition test chamber has been used to test suspensions of 7 UK and world traded coals in air and O2/CO2 mixtures typical of oxy-combustion conditions. The coals varied in rank from sub-bituminous to bituminous and were tested in varying concentrations from the ignition limit to 400g/m3. Following each successful test the combustion residue was collected, weighed and analysed within a thermogravimetric analyser, allowing Q factors to be estimated. The ignition limit varied slightly in air, but was mostly around the 200g/m3 level. With the exception of Coal C, which was much harder to ignite, it correlated roughly with coal rank. The ignition limit changed significantly with O2 concentration when in mixed O2/CO2 gases. Only a few high volatile coals ignited in 21% O2/CO2 v/v, and then only with a 2500 J, rather than a 1000J, igniter. An increase in O2/CO2 levels to 30 or 35% gave ignition patterns similar to those carried out in air with a further increase to 40% having little additional effect. In addition the minimum ignition concentration decreased with increase in O2. Heterogeneous combustion or gasification of the coal by CO2 appears to be confirmed by comparing weight loss results for air and O2/CO2 mixtures respectively for an equivalent peak pressure rise.

Jan 1, 2009

By J. W. Town

The Bureau of Mines studied the effects of reducing gas composition, tem-perature, and superficial gas velocity on the regeneration rate of alkalized alumina. Regeneration was assumed to follow the simple first order reaction for removal of sorbed S02: dµ/dt = -Kµ. An Arrhenius relationship can be plotted, which shows an activation energy of about 75 kcal/mole for simulated reformed propane. The general effects of the individual gases can be described as follows: (1) CO and H2 produced rates proportional to their con-centrations, up to about 5 percent for each; (2) addition of CO2 had no effects on the regeneration rate by CO; (3) the regeneration rate by H2 was lowered by the addition of H2O while the regeneration rate by CO was increased by 0 addition; (4) H2S showed a positive effect up to concentration levels of about 2 percent and then produced a rapid negative effect; (5) carbonyl sulfate (COS) increased the sulfur content; and (6) propane was as effective in regenerating the loaded pellets as was simulated reformed propane.

Jan 1, 1971

By P. W. Jeran, C. D. Sullivan, C. M. McCulloch

A series of geological surveys were completed in six coal mines in connection with a Bureau of Mines research program on methane control. The aim of these surveys was twofold: First, to study the overall geology of the coalbed, and second to use the resulting data to evaluate the influence of the geological characteristics of the coalbed on safe and efficient coal extraction. This report explains the advantages of geologic maps and fence diagrams in coal mining, and how the knowledge gained from such geologic investigations of mines can help control many underground problems.

Jan 1, 1975

By K. P. V. Lei

The Bureau of Mines as part of its research effort to minimize the generation of hydrometallurgical waste, investigated a sodium sulfide leaching-electrolysis procedure for treating hydrometallurgical residues for elemental sulfur and base-metals recovery. Research was conducted on a leaching residue from a lead concentrate. The following procedure was developed. 1. The elemental sulfur was dissolved as polysulfide with an Na2S solution. 2. The resultant metal sulfide bearing residue was oxidatively acid leached in a cationic membrane electrolysis cell; the metals were solu¬bilized at the anode, and a base was generated at the cathode. 3. The elemental sulfur was recovered from the polysulfide solution by neutralizing with the acid in the anolyte. Byproducts of the neutralization were H2S and a sodium salt solution. 4. Sodium sulfide was regenerated by reacting the H2S byproduct with the base in the catholyte. 5. Lead as PbCL2 was recovered from the anode residue by brine leaching, and the other metals were recovered from the sodium salt solution as metal sulfides. 6. The barren filtrate from the metal sulfide precipitation constituted the recycled electrolyte. Ninety-eight percent of the elemental sulfur, 98 pct of the lead, and up to 80 pct of other accessory metals were recovered from a residue obtained from the FeCl3-NaCl leaching of a lead concentrate.

Jan 1, 1982

By Jerry L. Huiatt

An accurate and reproducible procedure was developed using the gas-liquid chromatograph to quantitatively measure oleic acid on flotation products and in flotation water phases. The method comprised extraction of the oleic acid from the mineral surfaces with alcoholic NaOH, esterification of the extracted oleate, and chromatography of the methyl ester with an internal standard. Quantitative analysis of oleic acid on flotation products from test tube and bench-scale flotation tests with pure minerals and with natural ores proved the applicability of the method on a variety of minerals. The accountability of oleic acid added was 100 percent, ±5 percent.

Jan 1, 1968

By Terry J. Close

The Gates of the Mountains Wilderness study area is underlain by intrusive and sedimentary rocks, mainly limestone. No limestone has been produced from the study area; suitable material is more readily available elsewhere. Small amounts of gold, sapphires, and corundum were produced from a placer deposit along the banks of the Missouri River. The remaining gravel contains low mineral values. Other alluvial deposits along the Missouri River and Beaver Creek contain no identified economic resources other than sand and gravel. Some deposits could provide suitable construction material for local use.

Jan 1, 1984

By David C. Oyler, Herbert H. Fields, William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to sup- port the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

Several short color films describing new technology developed through Bureau of Mines research are available on a loan basis. The films review results of Bureau research programs aimed at aiding the minerals industry by increasing mine productivity, ensuring worker health and safety, and enhancing minerals recovery, processing and recycling. Most of the films are available in a choice of for mats: 16mm film, ½" VHS cassette tape, or ¾" U-matic tape. The films are loaned by the Bureau of Mines free of charge; borrowers are requested to pay only the return postage and for any damage to the films. All titles are also available for purchase in 16mm or videotape formats. Interested persons wishing to borrow or purchase a film should specify its title and the preferred and alternate showing dates. All requests should be addressed to: Motion Picture Library Bureau of Mines Cochrans Mill Road P.O. Box 18070 Pittsburgh, PA 15236 A short description of each film follows: Safer Coal Mining Equipment Traces the development of modified conventional and continuous mining equipment, beginning with an investigation of the problems encountered with mining equipment and continuing through long-term testing of the modified equipment in two mines. "Human engineered" coal mining machines are shown in operation. These machines include features such as adjustable cabs, easy access controls, improved illumination, and other safety improvements. (19 min)

Jan 1, 1986

By M. L. Skow, Maurice Deul, M. G. Zabetakis

This Bureau of Mines report presents a brief summary of the explosion trends in United States coal mines for the past 160 years. These trends show that in spite of the overall improvements in mine safety, the number of fatalities from ignitions of methane has actually increased in recent years. Suggestions are made of procedures that can be utilized to reverse this trend.

Jan 1, 1972