Search Documents

By Thomas M. Barczak

This U.S. Bureau of Mines report is intended to assist coal mine operators in the selection of longwall supports by providing advanced guidelines for performance testing and standardized test documentation to facilitate support comparisons. These advanced guidelines culminate in a series of proposed tests to evaluate (1) support resistance characteristics, (2) stiffness characteristics, (3) leg mechanics, (4) stability, (5) load transfer mechanics, and (6) structural integrity. The Bureau has conducted extensive studies on shield mechanics to identify boundary conditions that induce loading in support components, which is often not included in current testing techniques. This report discusses influential parameters that affect support behavior and provides insight into how components are loaded and what conditions produce the most severe loading. Testing philosophies and techniques in both active and static frames are discussed. Proper methods for determining support resistance are described and instrumentation requirements for advanced performance testing are provided.

Jan 1, 1989

By R. E. Hall

When the criterion for control of scale prevention on the evaporating surfaces is made the conditions in the concentrated boiler water, then this control becomes an exact operation amenable to an accuracy commensurate with all other operations in the boiler room. The responsibility in boiler water conditioning, however, includes more than clean surfaces. Corrosion in feed lines, economizers and the boiler is a function of the condition of the later, and must be controlled. Steam line and turbine blading deposits must be obviated by the system of conditioning. By the chemical treatment employed, the amount and character of noncondensable uses in the steam must be controlled in accordance with the intended use of the steam. All. in all, the responsibility in boiler crater conditioning ends not with the entrance of the water into the boiler but with the passage from the boiler nozzle of steam, the dryness and rarity of which are defined by the uses to be made thereof. A clearer conception of the scope of boiler water conditioning can be obtained by reference to a diagram of the surfaces (Figure 1) at which it functions. Consideration of this diagram leads to the following outline for the problems of boiler water conditioning: (a) Prevention of scale formation on surfaces (1) In contact with water but at which no evaporation occurs. (2) At which evaporation is occurring.

Jan 1, 1926

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operatons at or near mines.

Jan 1, 1963

By Alan R. Buehler

A mineral survey of the 20,792-acre Sand Butte WSA (Wilderness study Area), ID-57-8, was conducted by U.S. Bureau of Mines personnel in 1985, at the request of the Bureau of Land Management. The WSA is in Lincoln County, south-central Idaho, about 15 miles south-southeast of Carey. There are no mines, prospects, or claims within the WSA. Basaltic lava is the only rock type exposed within the WSA. The only mineral resource is a few tons of a platy variety of lava (slab pahoehoe) which is suitable for use as decorative stone. Similar slab pahoehoe, produced from other lava fields in southern Idaho, retails for approximately $125/ton. The deposit in the WSA is too small to be mined commercially but may have value to consumers who gather their own decorative stone. INTRODUCTION A mineral survey of the Sand Butte WSA (Wilderness Study Area) 1/ was conducted in June 1985 by the USBM (U.S. Bureau of Mines) and the USGS (U.S. Geological Survey) at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will he used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. The immediate goal of this and other USBM mineral surveys is to provide data to the President, Congress, government agencies, and the public for land-use decisions. The long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By d&apos, Kathleen J. Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By David C. Oyler

The U.S. Bureau of Mines and the United States Steel Corporation evaluated the progress of methane drainage at the Oak Grove, AL, degasification pattern. Coalbed pressures were monitored between December 1981 and November 1985. Formation pressures, in the lower bench of the Mary Lee Coalbed, were reduced from 400 lbf/in2(ga) in 1977 to 50 lbf/in2(ga) in November 1985. Gas contents of coal cores obtained from monitor wells were compared with coalbed gas contents measured in 1976. Data indicated a 48- to 56-pct reduction within the pattern and a 29-pct reduction at a point 500 ft outside the pattern. The effect of the advance of a section of the Oak Grove Mine on changes in gas and water production rates in the pattern was evaluated. Gas production increases were noted in 12 wells; water production decreases were noted in 6. The times of initial influence indicate the presence of a zone of high permeability within the pattern. This zone correlates well in orientation and location with a fracture zone mined through at the mine. The existence of such fracture zones could have a significant effect on productivity of individual coalbed methane wells.

Jan 1, 1989

By Ivette E. Torres

Many significant events that began in 1990-91 continued to have a profound impact in the world minerals economy in 1992. The dissolution of the U.S.S.R. and the formal breakup of the Council for Mutual Economic Assistance (CMEA) had significant effects far beyond the geographic boundaries of Europe and Central Eurasia. CMEA's network of economic interdependence had relied on central planning, a variety of subsidies, and barter agreements that allowed its members to function without the pressures of productivity and efficiency. In the mineral sector, many decisions had been made based on the need for military planning and technology competition with the market economy world. Because of inexpensive oil available through subsidies and technology assistance from the former U.S.S.R., industries III CMEA member countries had been able to function and maintain production to supply minerals and materials required to support the policies of the central plan. In 1992, most of the former CMEA countries decreased their output of many minerals. In some cases, the network of production that had been in place was severed. Political and economic instability, destruction of infrastructure, and new priorities were affecting other mineral industries in the area. In late 1991, 15 independent countries replaced the U.S.S.R. and in early 1991 the former CMEA countries found themselves trying to adjust to the realities of economic independence and the need to compete with former allies for survival. Although 11 of the 15 former Soviet republics joined in the Commonwealth of Independent States (CIS) in December 1991, in 1992, individual economic needs exceeded the needs of the Commonwealth III importance. As a result, new mineral trade patterns emerged as minerals were used as a source of much needed capital.

Jan 1, 1994

By A. W. Deurbrouck

This Bureau of Mines report describes the washability characteristics of 14 coalbed samples collected in Wyoming. Such data is needed to evaluate the quality of the coals of the West where most of our low-sulfur-content coal reserves are found. Of the 14 samples included in this report 13 had a total sulfur content of 1.1 percent or less. All of the samples contained low per¬centages of ash or could be readily washed to a desirable ash level with minimal loss of yield. The coals ranged in rank from high-volatile B bituminous to subbituminous C, although 10 of the samples were high-volatile C bituminous. The coalbeds varied in thickness from 4.5 to an unknown thickness greater than 67.5 feet.

Jan 1, 1971

By Edward P. Barrett

[Iron oxides, when reduced at temperatures below 900° form a dark gray substance, very porous bait otherwise in almost the same form as the original particles. In the temperature ire range of 1,000 to 1,100° the product is pertly sintered but still shows the outlines of the original particles. Those products are known as "sponge iron." At temperatures of 1,100 to 1,2000 the metallic iron begins to flow together and to a semifused, pasty, porous mass called a "bloom," which can he worked under a hammer to form a product similar to wrought iron; it contains slag inclusions and is too low in carbon to make steel. If the temperature is 1,300 to 1,300°, part of the iron will fuse enough to absorb more carbon. The dissolved carbon lowers the melting point and still more carbon is absorbed. The melted portion acts a flux for the unmelted metallic particles until the entire mass becomes a high-carbon fluid known as "cast iron." Sponge iron was probably the form in which the first iron was recovered from the ores. As early as the eighth century the Catlan forge3 developed into a low-shaft furnace known as the "high bloomary," in which iron eras produced in the form of a pasty mass. In 1340 the first blast furnace was built in Belgium. The greater part of the iron was made into wrought-iron blooms by crude puddling processes. Charcoal was used as the fuel until tie latter part of the 17th century when coke was used in England. In 1865 Bessemer built his first converter in. England, and within a few years the Siemen's regenerative open-hearth furnace was developed, also in England. Enormous expansion in the metallurgy of iron followed. The idea of "direct processes" for the production of iron arid steel has persisted throughout all this time. The production of steel from sponge iron has theoretical advantages over the present-day standard methods, and handreds of so--called "direct processes" have been proposed or tried during the past century.4]

Jan 1, 1929

By E. Chin

Natural gas was Bangladesh's only significant exploited mineral. A few other minerals or mineral-based commodities were produced for local consumption. The most valuable were nitrogen fertilizer, salt, cement, and clay for brick.2 The most important mineral industry development of 1987 was the start of modest production of crude oil, the first discovered and produced in the country. PRODUCTION AND TIADE Production of natural gas from the nation's huge reserves continued to increase but was limited by the lack of residential and industrial demand. Gas reserves of 7 trillion to 16 trillion cubic feet were sufficient for far more production than the country could efficiently utilize for many years. The country's consumption-to-reserves ratio was one of the lowest of the developing nations. Mineral exports have been insignificant, comprising a small amount of nitrogen fertilizer. Nitrogenous fertilizer exports could become important when planned new capacity comes on-stream. Mineral imports were dominated by crude petroleum.

Jan 1, 1989

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By R. E. Morgan, Barkleym J. F.

"INTRODUCTION Wood burned for commercial heat and power usually is waste material from some manufacturing process. The amount of it reaches substantial proportions. It is estimated that over 50 percent of the timber cut for lumber becomes ""waste"" in the process - sawdust, shavings, trimmings, slabs, and bark. Woodworking manufacturing processes also produce much waste. The incentive to use this waste has resulted in much development of wood-burning equipment to produce heat and power. To answer general inquiries received by the Bureau, this publication covering developments along these lines was written. There is included a bibliography of additional information on the subject.COMPOSITION AND BURNING CHARACTERISTICS OF WOODThe approximate composition of moisture-free wood is, in even figures:PercentHydrogen 6Carbon 49Oxygen 44Ash 1Total 100This composition corresponds to about C6H1005. Moisture is essentially always associated with wood. Green wood contains approximately 30 to 50 percent moisture; air-dried or seasoned wood contains 15 to 25 percent and kiln-dried about 8 percent. Exposed to the weather, wood absorbs and gives off moisture depending on weather conditions and water contact.""Dry"" wood ignites relatively quickly and readily gives off volatile matter when heated. Long flames and smoke easily occur during burning. The burning action is substantially retarded, however, by appreciable moisture content; ignition is more difficult. When the moisture content is more than about 70 percent, an auxiliary fuel is required to maintain combustion. One of the main factors in the problem of the satisfactory and smokeless combustion of wood is its moisture content."

Sep 1, 1950

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By Allen D. Look, J. Howard Bird

"INTRODUCTION The Phelps-Dodge Corp. New Cornelia Branch open-pit copper mine operated without a fatality in the drilling and blasting department from December 13, 1937, to April 1, 1947, and continuing.Between the dates named the explosives crews had a total of 746,520 man-hours of exposure and handled 12,000 tons of explosives, over 770,000 detonators, 2,300,000 feet of fuse, and 7,700,000 feet of Primacord in loading holes to break 116,780,000 tons of material.It is the purpose of this paper to record the procautions taken to insure safe handling of explosives at this operation where safety is definitely a matter of forethought rather than chance.GENERAL INFORMATIONThe New Cornelia Branch open-pit mine operates on a large, low-grade, disseminated-copper deposit about one-half mile south of Ajo, Ariz. The pit is approximately oval; the ore body being some 4,800 feet long and 2,750 feet wide. Ore is mined with electric shovels loading into railroad cars. All benches in- the pit are 40 feet in height except two, which are 60 feet high.The New Cornelia ore body differs from most porphyry-copper deposits in being hard and siliceous. In common with the other low-grade porphyry-copper deposits, continued operation is possible only with economical handling of large tonnages. This has necessitated a great deal of study in the evolution of a safe and efficient method of handling the large quantities of explosives needed in breaking this hard-rock material."

Feb 1, 1948

By J. H. Maysilles

The Bureau of Mines, U.S. Department of the Interior, is investigating several types of low-grade uranium deposits. Projections indicate that an increased percentage of future production will be derived from such sources. One material studied was from the Coso Mountains of California; this material contained 0.04 to 0.12 percent U3O8. The deposit contains at least two distinct types of mineralization. The material representing the bulk of this deposit was amenable to acid leaching; 80 to 85 percent U308 extraction resulted from leaching with 20 to 40 pounds per ton of sulfuric acid. No oxidizing agent was required. This ore fraction could be treated by either agitation or percolation leaching. Uranium recovery and purification from the acid leach solution was accomplished using anion exchange followed by precipitation with hydrogen peroxide and ammonia. The second type of mineral was very refractory to acid leaching; a maximum extraction of only 44 percent was obtained with sulfuric acid. Nitric and hydrochloric acids were ineffective also.

Jan 1, 1978

By Paul S. Lewis

Bench-scale experiment~ by the Bureau of Mines showed the gross effect of retention times ranging from 0.1 to 14.5 minutes on the conversion of high-volatile C bituminous coal to liquids and gases. The uncatalyzed coal was hydrogenated at 400°, 450°, and 538° C. and 500, 1,000, and 2,000 p.s.i.g. The percent coal conversion increased rapidly during the initial 3 minutes and asymptotically approached a maximum within 7 minutes at all conditions. Reasonably good correlations of coal conversion with time, pressure, and temperature were obtained. Temperatures up to 900° C. and retention times of about 1 minute are recommended for future experiments with the objective of producing only gaseous hydrocarbons and partially devolatilized coal suitable for use as solid fuel. The reactor contained 13 semicircular ledges, and the retention time was controlled by the rotation of scrapers which swept the coal from ledge to ledge. Only coal feeds that did not adhere to the internal mechanism could be used.

Jan 1, 1961

By T. G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a porphyry copper sulfide ore. The purpose was to determine the effects on copper leaching of additions of NaCI to a conventional sulfate leach system and to analyze the oxidant requirements and the oxidation products that resulted from leaching of the sulfide minerals in the ore. Baseline sulfate and sulfate plus 2-pct-NaCl-leach-solution experiments employing 167-kg (367-lb) and 152-kg (333-lb) charges, respectively, were conducted. The minus 25.4-cm (10-inch) ore was leached at 90° C under flooded conditions with 2.8 MPa (400 psig) of oxygen bubbling through the system. Sixty-seven pct of the copper was extracted in 1,236 days of leaching in the NaCI experiment, whereas 47 pct of the copper was extracted in 913 days of leaching in the baseline experiment. Diffusion into and out of the ore fragments controlled the rate of leaching, which precluded enhancement of the leach rate by the chloride ions. The calculated oxygen consumption was 3.17 kg/kg of copper extracted in the baseline experiment and 3.46 kg/kg of copper extracted in the experiment to determine the effect of chloride ions.

Jan 1, 1982

By J. E. Hamak

This publication contains analyses and related source data for 144 natural gas samples from 19 States. Of the total samples, 139 were collected during calendar year 1990. The remainder were collected earlier, but releases granting permission to publish were not received until 1990. All samples were obtained and analyzed as part of the U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free-market economies. This survey has been conducted since 1917. The analyses were made by mass spectrometer and chromatograph.

Jan 1, 1991

By J. W. Thompson

CONSTRUCTION OF STATUTE-SALE BY ENTRYMAN. The timber and stone act (20 Stat., 89) does not forbid an entryman from alienating his interest in his claim; but the act makes illegal any prior agreement by which the entryman acts for another in the purchase. Worden v. United States, 204Fed., 1, p. 4, April, 1913. ASSUMPTION OF DEBT BY GRANTEE-LIABILITY TO CREDITOR OF GRANTOR. A grantee of a mine who agrees to pay the grantor's debts in part payment of the purchase price of the mines becomes to that extent the principal debtor, and the grantor becomes the surety, and the grantor's creditor may in equity enforce his claim against the grantee of the mine, and the grantor in such a case is not a necessary party. Silver King Coalition Mines Co. v. Silver King Consolidated Mining Co., 204Fed., 166, p. 169, April, 1913. RIGHT OF COTENANT TO MINE AND SELL. A cotentant in exclusive possession' of mining property who extracts and sells ore is entitled to charge against the proceeds of the sale the reasonable and necessary expense of its extraction and marketing, as in such case the cotenant is not a trespasser.

Jan 1, 1914

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950