Search Documents

By Fredrick L. Johnson

No mineral resources were identified during the investigation of the White Cloud-Boulder RARE II area. Only a few claims have been located in the area and only two workings were found. However, there has been considerable exploration and mining activity near the RARE II area. Sand and gravel resources are abundant but similar deposits occur closer to market areas. There are no known coal, oil, or gas deposits. Most of the RARE II area is underlain by volcanic rocks. The likeliest host rocks for metallic minerals are the metasedimentary rocks exposed in the south part of the area; there is potential for zinc and silver resources at a prospect in that part. Traces of scheelite and powellite were observed in the Kent Peak-Ryan Peak area along hair-line fractures in calcareous country rock. While no significant concentrations of the minerals were found, their presence, a northwest alignment of prospects with similar deposits, and an abundance of dikes near the deposits, suggest that the intrusive system (Summit Creek stock) exposed near the head of Little Fall Creek may extend to the northwest under the RARE II area.

Jan 1, 1983

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1956 and 1956 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding table., for 1955 and 1956 follow in consecutive order under the following general sections: (A) General injury experience: Tables I to II: contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury data: Tables 12 to 77: Contain current data on causes of injuries, distribution of injuries by part of body injured, clays of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 78 to 87: Contain data on injuries, injury rates, employment, cause of injuries, aid severity rates by States. (D) Major disasters: Table 88: Contains data on major disasters, 1947 -56. A major disaster is defined as a single accident in which, or as the result of which, five or more persons are killed instantly or died at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 89 to 93: Contain data on fatalities and their causes at bituminous-coal and anthracite mines from the earliest records through 1956.

Jan 1, 1960

By Russel R. Bohn

The objectives of this study were to: (a) determine the state of the art for the control effectiveness of various chemical dust suppressants, (b) field test the effectiveness of the dust suppressants, and (c) develop technical guidelines for selecting and implementing cost effective tailings pond dust control programs. Chemical stabilizers evaluated under field conditions were: Coherax, Calcium Lignosulfonate, Nalco 656, 655, and Magnesium Chloride. Testing in the field utilized a portable field in-situ wind tunnel. The wind tunnel was placed on the tailings surface and simulated wind speeds of up to 80 mph were used to determine wind erosion threshold velocities. Emission rate testing was performed with the wind tunnel through the use of a real-time cascade impactor. A control cost effectiveness evaluation was performed to determine how efficient the chemical stabilizers were on a dollars expended per acre basis.

Jan 1, 1983

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940 to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the? Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940, to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956

By W. E. Schroeder

Two underground installations of the sprayfan system are described and evaluated. The spray fan proves capable of reducing by 1300 percent downtime due to high methane. Spray fan face ventilation at 20 ft brattice setback is shown to give improved methane control over conventional sprays at 10 ft setback. In addition, this report describes: ? A simple method for determining the most economical application of ventilation for face methane control ? The effect of place variables (primary ventilation, auxiliary ventilation, seam height, etc.) on methane concentrations ? The correlation of methane concentrations with brattice setback. These results are utilized to suggest a safer and more economical approach to face methane control.

Jan 1, 1981

By T. A. Raczek

Materials for stronger ventilation tubing for underground use in hardrock mines were developed. The new material composites were evaluated in performance characteristics and compared to currently used materials. The materials were compared on tear, tensile, puncture and flammability properties. Based on cost versus performance data, a polyester film bonded to a polyester fabric was selected as the candidate material for field testing. Ventilation tubing fabricated from the selected material was field tested in two underground uranium mines for four-month periods. The test results indicated that the new composite showed an increase in useful life in the majority of applications, However, the cost performance ratio was not significantly improved to warrant commercialization of the product. When connected directly to some blowers, the material in close proximity to the blower deteriorated. However, material which was punctured or torn by mechanical means did not have further propagation of the tear. The high tear strength of the material prevented further damage. Improved methods of repairing inflated ventilation tubing were investigated and developed. All the repair methods were portable and self-contained. Repair kits based on adhesives, pressure sensitive tapes, and mechanical means were evaluated. Plier staplers and patch systems based on pressure sensitive adhesive proved to be most functional.

Jan 1, 1980

By John H. Johnson

This report covers research which is directed toward the measurement and control of underground mine diesel emissions. The report consists of three separate reports presented as Sections 1, 2, and 3. Section 1 "Emissions Measurement Apparatus" (EMA 1) discusses the selection and evaluation of instruments and procedures to be used as part of a diesel tailpipe emissions dilution and measurement apparatus. The instruments selected for gaseous pollutants are the Energetics Science Inc.* E.S.I.) 2000 for CO, the E.S.I. 7000 for NO and N02, and the Fuji ZFP5 for C02. Particulate matter is presently measured with the Celesco 1013 Smoke Opacity Meter. The raw exhaust concentration of one of these constituents is used Lo calculate the dilution ratio. Either a modified high range E.S.I. 2000 CO instrument or a Daco Products Cobra C02 instrument can be used, but neither is totally satisfactory. The study also indicated that it may he possible to increase the sample collection time from 15 seconds to the total 30 seconds over which the engine can be loaded without increasing the probability of damaging the vehicle hydraulic systems. Section 2 "The Effect of Fuels, Catalysts and a Filter Trap on Drift Pollutant Concentrations" discusses research in the Mine Air Quality Laboratory. A Wagner ST5D LHD with a Deutz F8L714 engine was used to compare three exhaust aftertreatment devices and a muffler-only system. The effect of these four systems on CO, C02, NO and N02 and on total, soluble, sulfate, and solid particulate matter was measured in the drift and on the LHD. The filter trap successfully reduced particulate matter for both fuels without significantly increasing the concentrations of any of the other constituents. The PTX catalyst was effective in reducing CO, and soluble particulate, but significantly increased N02 and solid and sulfate particulate matter. The Oxy Cat catalyst tested didn't seem to he working on the gases, and it significantly increased sulfate, soluble arid solid particulate concentrations. Section 3 "Diesel/Coal Particulate Matter Characterization by Laser Raman Spectroscopy" covers basic research on a method for determining the percentage by weight of diesel particulate on a filter containing a diesel-coal mixture. Signal-averaged Raman spectra provide the necessary precision. The method developed is non-destructive and uses as-received filters requiring no sample manipulation. Particulate with diesel contents in the range of 10 to 50% by weight have been analyzed with accuracies better than 6%t of the mean value. A number of samples containing diesel-coal mixtures were characterized by the procedures developed and the results are analyzed in light of various spectral and other system variables including coal rank and form and diesel engine operating conditions.

Jan 1, 1982

By A. G. Galaitsis

This report summarizes the work performed under the USBM Contract No. J0245001. The purpose of this work was to expand and improve the scope and accuracy of the method developed under USBM Contract No. J0113056 for the prediction of the number of overexposed workers in the mining industry. A significant portion of the noise data were acquired during mine visits-that took place in the-course of this contract. These data were obtained with time-resolved dosimeters which among other things store a time history of the sampled noise for an eight hour work period. The remainder of the noise data have been obtained from MSHA files and from other BoM-sponsored projects. The report reviews the prediction model, discusses the model's assumptions and approximations, describes the function of the developed software, offers typical examples on the use of the software and includes plots of the newly acquired noise data records.

Jan 1, 1986

By Thomas E. Finch

This report is an engineering-economic evaluation of alternate methods of handling the parting between two coal seams. It consists of evaluations of parting stowing techniques applicable in a representative, thick seam western United States mine. Methods are examined for their potential implementation, and an estimated operating cost per yard of material moved is developed. The methods are of two categories castback or haulback. Haulback methods use truck haulage except With scrapers, and the castback methods are a direct stowage with no intermediate haulage equipment. Possible equipment combinations include draglines, shovels, hydraulic backhoes, bucket wheel excavators, scrapers, and front end loaders. The purpose of this report is to evaluate the effective competetiveness of the various alternatives.

Jan 1, 1975

By R. H. Hiltz

The Coal Mine Health and Safety Act of 1969 legislated maximum dust levels for the working place. As the law was implemented, extensive efforts were undertaken to provide the technology necessary to control dust generation. One approach to dust control was the use of high expansion foam in place of the usual water sprays on coal cutting equipment. At the time of the act, high expansion foam had already seen considerable testing for the suppression of dust in underground coal mines. Work by MSA, several coal companies and the Bureau of Mines itself had provided data which showed foam to have some merit as a dust control mechanism. It suffered in a few areas, however, which limited its practical application. Its principal difficulty was persistence which hampered operations due to foam buildup, but problems were also encountered due to equipment size and form.

Jan 1, 1975

By Robert Stefanko

The growing demand for energy during the post World War I and World War II periods has prompted underground coal production to increase rapidly. This has been met primarily by mine mechanization, resulting in the development and application of new mining machine types. Correspondingly, the total connected horsepower of each machine as well as the number employed has enlarged rapidly since 1950. (2,3,9,14,16,17) Electrical consumption for each mine has also grown. In the early years of mining electrical applications, only d-c power was utilized underground. Yet, d-c machine limitations were soon realized, and many a-c systems were substituted to permit economic and efficient utilization of a-c distribution and motors. Due to the attractive torque characteristics, ease of distribution and speed control, several traction applications have continued to be powered by d-c motors. The result has been the now prevalent use of mixed a-c/d-c mine power. However, augmented electrical power employment seems to have added to underground coal mining electrical accidents.

Jan 1, 1974

Electrical trailing cable used to power coal mining machinery is frequently damaged by tensile strain or crushing by mining machines running over the cable. A major problem is finding the exact location of a short or open in this cable so it may be repaired. A major problem is finding the exact location of a short or open in this cable so it may be repaired. FMC Corporation was awarded modification III to USBM Contract H0122011 to continue development and testing of cable fault locators, resulting in delivery of: 1. A prototype electrostatic/electromagnetic/ TDR transmitter and an electrostatic/electro-magnetic receiver sot that: o Locates cable faults by time domain reflectometry o Locates opens by detecting electrostatic signals o Locates shorts by electromagnetic coupling. 2. A prototype infrared detector and an infrared detector power supply that heats a shorted area by applying high current (at low voltage) and locating a short by infrared output. 3. Twelve production infrared detectors. 4. Detail drawings for all of the developed instruments.

Jan 1, 1973

Sixteen papers concerned with the technology and utilization of low-rank fossil fuels are presented as the proceedings of the 1973 lignite symposium. This symposium, the seventh in a series of biennial meetings, was cosponsored by the Bureau of Mines and the University of North Dakota.

Jan 1, 1974

By C. M. Harrer

The location, features, quality, and extent of iron ore deposits are evaluated in this Bureau of Mines report. The results of pioneer beneficiation on Wyoming taconites and their success are discussed along with developments in the iron-ore mining industry, markets, and economics. Market potential, transportation, resource developments, taxation, cost of iron ore enterprises, and the future of Wyoming iron resources are evaluated. Although occurrences of iron ores in Wyoming were known prior to 1870, early production to 1900 was as a nonferrous metallurgical flux and as mineral pigment for paints. In 1901, the Hartville-Sunrise hematite deposits were available to the Western iron and steel industry and in 1962, the first western taconite operation was placed in production at Atlantic City, Wyo. This investigation disclosed the probability of other large iron deposits in Wyoming. Taconite in the Bradley Peak area of the Seminoe Mountains has a potentiality of 100 million tons; that in the Owl Creek Mountains may prove very large also. Pioneer beneficiation testing has been included, and results have been generally encouraging. Research continues on the large titaniferous magnetite deposits of Albany County, Wyo. At present high-density titaniferous magnetite is being mined and processed at Iron Mountain for heavy-aggregate and as a sized coating for underwater pipelines. Ample mineral raw materials needed for mining and processing Wyoming iron ores are available. Investments for iron-ore processing plants will generally be large, particularly for taconite and titaniferous magnetite.

Jan 1, 1966

By C. M. Harrer

The location, features, quality, and extent of iron ore deposits are evaluated in this Bureau of Mines report. The results of pioneer beneficiation on Wyoming taconites and their success are discussed along with developments in the iron-ore mining industry, markets, and economics. Market potential, transportation, resource developments, taxation, cost of iron ore enterprises, and the future of Wyoming iron resources are evaluated. Although occurrences of iron ores in Wyoming were known prior to 1870, early production to 1900 was as a nonferrous metallurgical flux and as mineral pigment for paints. In 1901, the Hartville-Sunrise hematite deposits were available to the Western iron and steel industry and in 1962, the first western taconite operation was placed in production at Atlantic City, Wyo. This investigation disclosed the probability of other large iron deposits in Wyoming. Taconite in the Bradley Peak area of the Seminoe Mountains has a potentiality of 100 million tons; that in the Owl Creek Mountains may prove very large also. Pioneer beneficiation testing has been included, and results have been generally encouraging. Research continues on the large titaniferous magnetite deposits of Albany County, Wyo. At present high-density titaniferous magnetite is being mined and processed at Iron Mountain for heavy-aggregate and as a sized coating for underwater pipelines. Ample mineral raw materials needed for mining and processing Wyoming iron ores are available. Investments for iron-ore processing plants will generally be large, particularly for taconite and titaniferous magnetite.

Jan 1, 1966

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry For the years 1966-67. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent or disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973